Polpriklopnik z nizko nakladalno ploščadjo

MÜLLER-MITTELTAL 3- achs Satteltiefl.-Luft-Lenk,hydr. Auffahrram.

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle with steering function and electro-pneumatic steering lock ----Suspension: * Air suspension with lifting/lowering system and RtR valve ----Electrics / Lighting: * Tire pressure monitoring system (TPMS) * Smartboard operator panel mounted on the trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon at rear left ----General attachments: * Side underrun protection * Landing legs at the front and mechanical swing supports at rear of chassis * Straight steel mudguards * Spare wheel carrier mounted under chassis, right side ----Low-loader platform: * Gooseneck platform with 45° chamfered front corners and tool box at the front made of galvanized steel, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm high aluminum side boards (RAL 9010 pure white) foldable and removable, along the sides of the gooseneck platform * Rear panel 150 mm high, plug-in * Rear slope on the gooseneck platform leading to low-bed, approx. 700 mm long * Gooseneck platform with 50 mm wooden planks; low-bed platform with 60 mm wooden planks * Tread plate over the axles ----Extensions: Dkjdpfxjpk D I As Al Hjl * 8 x mechanical folding extensions to a total width of 3 m (not on the rear slope, extension planks available with storage on gooseneck platform) * Mechanically adjustable warning panel sets, front and rear ----Load securing (Lashing package): * On the gooseneck platform: 2 x 6.3 t lashing rings per side and 3 x 5 t lashing bars per side on the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side and 4 x 10 t lashing rings, swivel and lowerable, embedded in the outer frame * 2 x 6.4 t lashing eyes per side and 1 lashing ring at the rear, in the excavator-arm recess * 2 x container locks immediately after the step in the low-bed platform ----Excavator-arm recess: * Continuous from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Access ramps: * Mechanical one-piece, hot-dip galvanized hydraulic access ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * Quadruple control block for future retrofitting of hydraulically lateral shifting ramps by customer * The outer plank on the ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output of 40 up to 120 liters/min in the truck) ----Loading dimensions: * Gooseneck platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen: approx. 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paint/Finish: * Chassis, access ramps, rear folding supports, and extension brackets are hot-dip galvanized * Axles, landing legs, and air reservoirs are painted in a shade of black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Sample images may show equipment not included in the offered vehicle ----Delivery time: * Available from week 38/2026

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, prva registracija: 03/2015, dolžina tovornega prostora: 134.450 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 480 mm, vzmetenje: hidravlika, Leto izdelave: 2015, Oprema: ABS, = Dodatne možnosti in oprema = - Centralno mazanje = Dodatne informacije = Konfiguracija osi Vzmetenje: hidravlično vzmetenje Zadnja os 1: Max. obremenitev osi: 12.000 kg; Krmiljena Zadnja os 2: Max. obremenitev osi: 12.000 kg; Krmiljena Teže Dkodpfsvtc Aiex Al Hsl Lastna teža: 12.660 kg Nosilnost: 34.340 kg Skupna dovoljena masa: 47.000 kg Funkcionalno Višina nakladalne površine: 48 cm Izvlečna nadgradnja: Da Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Finančne informacije Cena: Po dogovoru Dodatne informacije Za več informacij se obrnite na Davida F Middelmana.

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length Dksdsrgzv Nepfx Al Hel * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck

Stanje: novo, največja dovoljena obremenitev: 31.500 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, Oprema: ABS, Priekaba Wiese ar trijų ašių važiuokle, kėlimo stalu ir atverčiamu galu. Idealiai tinka šakinių krautuvų ir (arba) darbo platformų pervežimui. Techninės specifikacijos. 3 x 10 t ašys Pakeliama ašis Valdoma ašis su „Smart Steering“ (vairavimas į priekį ir atgal) Išorinio rėmo važiuoklė su nuolydžiu Galinė konstrukcija, tinkama 18 t, pritaikyta 2- ir 3-ašių vilkikams Hidraulinis kėlimo stalas reguliuojamas 3 pozicijose Atverčiamas galas su hidrauliniais išstumiamais elementais, tinkamas naudoti kaip užvažiavimo rampos, pervažiavimo rampos arba kaip pakrovimo platforma (Bendro ilgio sumažinimas pakėlus galą vertikaliai) Nuotolinis valdymas rampoms ir kėlimo stalui Priekinė sienelė Grotelinis grindų paviršius Daug tvirtinimo taškų „SmartBoard“ sistema Centrinė tepimo sistema Plieninė konstrukcija, cinkuota ir nudažyta Galima įsigyti daugybę papildomų pasirinkimų, pvz.: - Gervė Dkjdpfsvw Hmtex Al Hjl - Įrankių dėžė ant priekabos pakopos - Aliuminiai ratlankiai Daugiau informacijos pagal užklausą.

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Maximum speed: 80 km/h (legal) Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Turning radius king pin to rear approx.: 2,100 mm Coupling height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Load height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific legislation: Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform approx. 9,600 mm in length with rear bevel approx. 900 mm x 6°. Loading area after gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair of two-piece AXS steel ramps, approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Djdpfoizu Ntex Al Hekl Ramps individually hydraulically adjustable by approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle according to technical datasheet: C470319 Maximum gradient angle with lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion Load index 143/141J (144/144F) Brake System: WABCO EBS-E brake system according to EU regulations. No connecting cable to the tractor unit included. Lighting System: 24V lighting system in "ASPÖCK-NORDIK full LED" version according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation) Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). 6-Coat Paint Treatment: Entire steel structure shot-blasted after welding. 1 coat zinc-based primer, 1 coat adhesion primer. Topcoat consisting of 2 layers of 2K paint (acrylic) in a single RAL shade of choice, followed by cavity sealing with special wax. Rims in silver. Multi-colour and special coatings available at extra charge. Steel Construction: High-strength fine-grain steel structure. Steel grades: S355J2+N/S355MC (min. yield strength 355MPa) S690QL/S700MC (min. yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG-welding process to EN ISO 4063. Shielding gas M21 according to EN ISO 14175 Front bulkhead made of steel, detachable, approx. 400 mm high Connector strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. Anderson socket at the front connection strip. Rema 78051-00 & Amp. 150 V. Cable for supplying the electro-hydraulic power unit and/or

Stanje: rabljeno, največja dovoljena obremenitev: 42.500 kg, skupna masa: 60.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2022, with 12 axles, divided, hydraulically suspended, with hydromechanical forced steering, with rear taper and drive-on ramps STZ-L Gooseneck - robust welded steel construction - formed loading area 3,950 x 2,480 mm incl. tapered rear section - hydromechanical forced steering (dual-circuit steering) - turntable-mounted king pin plate with replaceable 2 or 3.5 inch king pin and adjustable steering wedge - fifth wheel load 24 t - rear turning radius: 2,600 mm Loading Deck - stepped outer beams 4,630 mm, 420 mm deep, providing a loading height of 470 mm or 830 mm with decking installed - extendable by 2,053 mm - includes aluminium bridging rails for creating a flat surface - excavator arm recess at rear of chassis: 4,900 mm long, 880 mm wide, 480 mm deep - chassis length at rear: 4,900 mm including 500 mm rear taper, loading height 890 mm - pair of wheel recesses in lower loading area - hydraulically suspended 3-axle chassis - divided Gigant axles with 600 mm stroke Rear of Vehicle - design: 500 mm rear taper - hydraulic rear support Drive-on Ramps - 2-piece ramps, length: 2,850 + 1,850 mm, width: 800 mm - rubber-coated surface with climbing strip Brake System - dual-line full air brake system with diaphragm brake cylinders - automatic load-dependent brake (ALB) - automatic rod plates (AGS) - parking brake operated via spring-loaded cylinders - ABV brake system Special Equipment - radio remote control for steering and ramp operation - central lubrication system Technical Data Gooseneck Loading area (LxW): 3,950 x 2,480 mm Dkjdpfx Ajw Etd Tel Hel Loaded saddle height: 1,300 mm Loading Deck Loading area (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Stepped outer beams: 4,630 mm long plus 2,053 mm extension Centre beam: 980 mm Excavator arm recess: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle with hydromechanical forced steering (dual-circuit steering)

Stanje: rabljeno, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2017, * SAF osi * Kolesni jaški * Hidravlične nakladalne rampe nastavljive po širini * Zračno vzmetenje * Razširljiv * Lastna teža: 11.020 kg -----Interna številka vozila: 11010----Pridržujemo si pravico do napak in vmesne prodaje. WhatsApp podpora na voljo! Dsdpfx Aljwta Ale Hskl Za vprašanja o vozilu ali dodatne informacije nam pišite preko WhatsAppa. WhatsApp nemščina, angleščina -- WhatsApp nemščina, angleščina, arabščina

Stanje: novo, lastna masa: 10.900 kg, največja dovoljena obremenitev: 37.100 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear bevel approx. 1,000 mm x 6° - Technical king pin load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,600 mm long with rear taper approx. 900 mm x 6° - Platform area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, with a load capacity of up to approx. 9,000 kg - Grating surface and steel sheet floor approx. 5 mm thick as additional reinforcement on the sloped section of the platform Ramps: - One pair of two-section AXS steel ramps, approx. 4,675 mm long and approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward - Painted sand coating on the outer frame and ramp tips - Flashing lights on the outer sides of the ramp tips with control switch next to the ramp operation panel - Ramp lock in transport position with quick-release fastener Axles, suspension and tires: - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steerable (trailing) - 1st axle with traction assistance - Operated via brake pedal in the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 Dsdpfx Asuadk Nel Hjkl - TPMS tire pressure monitoring system compliant with ECE R 141 - TPMS tire pressure sensors installed on all wheels including spare wheels Brake system: - WABCO EBS-E braking system in accordance with EU regulations Paintwork: - Trailer MB 7350 Novagrau Equipment included: - Removable front steel wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations, except for hydraulic winches - Gooseneck guide plate for the fifth wheel, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating with 5 mm steel underlay as additional reinforcement - Painted sand coating - Cutouts in the outer frame of loading platform and lift bed for hooking hydraulic ramp control valves on the right-hand side of the vehicle - 2" king pin - Central lubrication system with 1 pump, brand BEKAMAX - 1 pair of plug-in ALU side boards on the gooseneck, approx. 400 mm high, anodised - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope pressure roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m Djdpfxow Tgkbe Al Hskl * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026

Stanje: novo, največja dovoljena obremenitev: 36.980 kg, skupna masa: 43.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.440 mm, Leto izdelave: 2023, Oprema: ABS, Fzg.-Typ: MFCC Mitten-Heckschieber Container-Chassis für Container Mitten- und Heckaufschub Fahrgestell geeignet zur Aufnahme von 1x40 Fuss Standard Container ohne Gooseneckausführung Fahrgestell geeignet zur Aufnahme von 1x20 Fuss Containern heckbündig, Sattellast abhängig von Lastverteilung! Fahrgestell geeignet zur Aufnahme von 1x40' High Cube Container in Gooseneckausführung Fahrgestell geeignet zur Aufnahme von 2x20 Fuss Containern Fahrgestell geeignet zur Aufnahme von 1x30 Fuss Standard Container ohne Gooseneckausführung Fahrgestell geeignet zur Aufnahme von 1x45 Fuss Containern Das Chassis kann einfach durch Vor- und Rückwärtsfahren mit der Zugmaschine, aus- und eingeschoben werden. Auf diese Art und Weise, ist keine Kraft vom Fahrer notwendig und die Konstruktion ist Betriebssicher. Dkedpfxjtt Hu Aj Al Hjl Liftachse Mehrfach vorhanden Vermietung möglich!