Müller-Mitteltal Pt 30,0 Kompakt Gerade Fläche Container Nr.: 540 nakup rabljenega (9.163)

Stanje: rabljeno, lastna masa: 9.300 kg, največja dovoljena obremenitev: 14.700 kg, prva registracija: 02/2001, naslednji pregled (TÜV): 10/2024, skupna širina: 25.500 mm, vzmetenje: jeklo, velikost pnevmatike: 235 / 75 R 17.5 / 10mm, velikost sprednje pnevmatike: 235 / 75 R 17.5 / 10mm, obratovalna teža: 24.000 kg,

Stanje: rabljeno, največja dovoljena obremenitev: 6.800 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, prva registracija: 04/2026, Müller-Mitteltal KWH 9.9 ML Cable Transport Trailer with Diesel Engine Hfsdpsy R Ipnjfx Ag Ieg * KWH 9.9 ML * Drum brake system EBS 2S/2M * BPW axles * Leaf suspension with parabolic springs * Spring-assisted square tube supports at the rear with base plate; safety locking pins for various support heights * Drawbar with 40 mm or 50 mm bolt-type towing eye (height adjustable) * Fixture for additional drawbar, mounted laterally on the towing device, right side in driving direction * Chassis made of torsion-resistant square tubes and cross members * Plastic toolbox * LED lighting * Swivelling cable drum frame consisting of base frame, rotary bearings, and drum support arms * Drum support arm ends with tension lock for drum shaft securing * Locking of the swivelling cable drum frame to the chassis by means of a centrally positioned claw lock * Steel drum shaft 76 mm diameter with centering and rotating ends * For a drum diameter of 3,000 mm, a maximum drum width of 1,650 mm is possible * Hydraulic pull and push cylinders, motor-driven, with load-holding valve * Control valve with automatic neutral position and pressure relief valve * Hydraulic system connectors, hoses, and pipes in NW 13 * Required oil capacity approx. 10 liters * Drum drive motor-hydraulic with oil motor, valves, and rubber-coated drive rollers (adjustable). Hydraulic speed controller and brake for drum drive * Hydraulic pump unit driven by diesel engine with hand starter, 6.5 HP with gear pump (150 bar) * Pressure supply can be provided either by the truck hydraulics or the pump unit by changing connection lines * Weather protection cover, fully hot-galvanized without final paint coating * Tyres: 315/80 R22.5 Subject to prior sale and errors! Sale exclusively according to our General Terms and Conditions. Important Notice: Even though we carefully check every detail in our offers, errors may occur. Some mistakes may result from data transfer errors between the different platform providers. Therefore, all information is provided without guarantee and does not constitute a legal claim. Legal Disclaimer: This sales advertisement does not constitute an offer within the meaning of §145 BGB (German Civil Code). Rather, it provides information for contract initiation. The information provided is non-binding and does not represent warranted characteristics.

Stanje: rabljeno, lastna masa: 6.200 kg, največja dovoljena obremenitev: 23.800 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2006, vzmetenje: jeklo, velikost pnevmatike: 235/75R17,5 141/140J, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75R17,5 141/140J, velikost zadnje pnevmatike: 235/75R17,5 141/140J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Lashing eyes, -- Typographical errors, mistakes and changes excepted, sample images --, More data at: !, More details: ! Hjdpfoy Hh Icex Ag Iefg

Stanje: rabljeno, največja dovoljena obremenitev: 16.950 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2006, naslednji pregled (TÜV): 04/2026, Leto izdelave: 2006, * Müller Mitteltal T3 NG * Low-loader * Ramps * Twin tires * Permissible total weight: 24,000 kg * Unladen weight: 7,050 kg * Payload: 16,950 kg * Tyres: see pictures * BPW axles * Immediately available * Subject to prior sale and errors excepted Do you have any questions? Contact us for prompt advice – also available directly via WhatsApp: Hsdoyv Ug Djpfx Ag Iofg We offer: Net purchase for companies within the EU with VAT ID number as well as for customers from non-EU countries. Leasing and financing options. Handling of all customs formalities. Issuance of short-term and export license plates. Transport to the port. All prices listed on classified ad platforms are gross prices and already include the statutory VAT of 19%.

Stanje: rabljeno, največja dovoljena obremenitev: 31.820 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/1980, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 3.000 mm, skupna širina: 2.550 mm, skupna višina: 900 mm, Leto izdelave: 1980, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal T4 Low Loader Trailer * SAF axles with drum brakes * Twin tyres * Low bed with extendable loading platform * Hydraulic loading ramps, movable (2 units) * Drive-over gooseneck * Additional rear supports * Turntable construction ----Dimensions & loading area * Loading area approx. 9,800 mm * Loading width: 2,550 - 3,000 mm * Loading height: 900 mm ----* Permissible total weight: 40,000 kg * Payload: 31,820 kg * Tyres: 235/75R17.5 ----Vehicle number: 11892----Subject to errors and prior sale----Advertising and various lettering have been digitally removed. -----We are happy to assist you with any formalities arising from the purchase of a vehicle. Simply let us know your requirements and suggestions, and we will take care of the rest. Among other things, we can offer you the following services at an additional cost: ----Trade-in of your old vehicle TÜV/general inspection Complete export processing Financing brokerage Obtaining export license plates Vehicle transport Vehicle registration Recovery and vehicle transport Hfsdoy Skl Iepfx Ag Ieg ----Your VTS Team

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: Hjdpfxsq Ra D Ee Ag Isfg * Parabolic springs with equalizer unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by 300 mm * 40 mm flange drawbar eye ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic quarter mudguards * Plastic toolbox, front right, mounted externally on bulkhead ----Electrics / Lighting: * TPMS Tire Pressure Monitoring System * LED lighting ----Loading Platform: * Loading length: 6.27 m * Suitable for container transport * 50 mm softwood floor * Preparation in front of bulkhead for retrofitting container locks * Bolted smooth steel bulkhead * Hinged, trapezoidal-profile steel side panels with drop-side spring assist * Removable steel rear wall, can be stowed in front of the bulkhead between ramp mounts * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t recessed lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in the bulkhead and end beam for 1.2 t lashing options ----Ramps: * One-piece mechanical drive-up ramps with spring mechanism, single-operator use, approx. 2,750 x 600 mm (collapsible down to 20 mm) * Rear approach angle approx. 860 mm ----Tyres: * Tyres: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, rear wall, rear stanchions, and drive-up ramps * Side panels painted in RAL 9010 pure white * Painting of side walls in an individual RAL color available for a surcharge ----Information: * Subject to errors and prior sale * New vehicle with manufacturer warranty ----Delivery time: * Available from CW

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3-in-1: Suitable for hooklift containers, skip containers, and as a low loader ----Brakes: * EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 tonne axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * TPMS (Tyre Pressure Monitoring System), display on truck via EBS signal (no truck-side installation required) * LED rear lights 12/24V * 15-pin power connector ----General Attachments: * Toolbox made of powder-coated sheet steel * Spare wheel carrier basket, right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffers * Folding A-board at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer rails to guide roll-off containers * Steel floor with roller recesses in the bogie area Hfjdol Tld Iepfx Ag Ieg * For hooklift container transport, container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking system and mechanical plug-in stop angles at the front of the track * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable skip locators for lateral centering of the skips, front 4 locators plug-in with swinging stop * Weld seam as anti-slip surface in the ramp area * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for hooking in securing elements for positive and non-positive locking of skips, 4 cloverleaf-type lashing bars per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t lashing eyes per side flush-mounted in the outer frame ----Ramps: * Aluminium approach ramps (10.6 t per pair), 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment at rear) ----Paintwork: * Reflective contour tape on sides & rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Permissible gross weight technically up to 20,000 kg * New vehicle, never registered, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Type Towing Eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of fine-grain steel ----Tipper Platform: * Mesh hooks on sides and rear located at the central locking mounts, plus 2 on the front wall * Steel pallet two-way tipping body, front wall fixed, made of smooth plate; continuous collapsible sidewalls (without center posts), with drop side spring lifters and manual central locking for tilting * Rear stanchions bolted * Steel rear wall slid in front of the ramps * Each corner with 1 x 5 t lashing point; 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm floor made of fine-grain steel ----Ramps: * Two-piece mechanical grating drive-up ramps with aluminium tip section 2,150 + 1,300 mm x 600 mm (can be slid together manually up to 80 mm) Hfjdpfotr Sucjx Ag Isg ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical stabilizer legs, and ramps hot-dip galvanized * Axles, springs, air tanks, towing eye, and landing gear painted in black * Sidewalls and platform in RAL 9010 pure white * Paint finish of sidewalls and tipper platform available in RAL color of choice at extra charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Type Towing Eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of fine-grain steel Hfjdpstr St Ujfx Ag Isg ----Tipper Platform: * Mesh hooks on sides and rear located at the central locking mounts, plus 2 on the front wall * Steel pallet two-way tipping body, front wall fixed, made of smooth plate; continuous collapsible sidewalls (without center posts), with drop side spring lifters and manual central locking for tilting * Rear stanchions bolted * Steel rear wall slid in front of the ramps * Each corner with 1 x 5 t lashing point; 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm floor made of fine-grain steel ----Ramps: * Two-piece mechanical grating drive-up ramps with aluminium tip section 2,150 + 1,300 mm x 600 mm (can be slid together manually up to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical stabilizer legs, and ramps hot-dip galvanized * Axles, springs, air tanks, towing eye, and landing gear painted in black * Sidewalls and platform in RAL 9010 pure white * Paint finish of sidewalls and tipper platform available in RAL color of choice at extra charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flanged Drawbar Eye: * Height-adjustable drawbar by 300 mm * 40 mm flanged drawbar eye ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding rear supports * Plastic quarter mudguards * Plastic toolbox mounted front right on the bulkhead ----Electrics / Lighting: * RDÜ tire pressure monitoring system * LED lighting ----Loading Area: * Loading platform length: 6.27 m * Suitable for container transport * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks Hfodpfx Aervvfwog Ijg * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal profile steel, foldable with drop side spring lifter * Steel tailgate, insertable between ramp holders; stowable inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Each front and rear corner fitted with 1 x 6.3 t lashing point * Various holes in bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical drive-on ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be retracted to 20 mm height) * Rear approach angle approx. 860 mm ----Tyres: * Tyres: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paint Finish: * Hot-dip galvanized chassis, drawbar, bulkhead, tailgate, rear stanchions, and ramps * Sideboard paint finish in RAL 9010 pure white * Painting of side walls in another RAL color possible at extra cost ----Information: * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Availability: * Available from CW (calendar week)

Stanje: rabljeno, največja dovoljena obremenitev: 6.940 kg, skupna masa: 10.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2018, naslednji pregled (TÜV): 11/2026, dolžina tovornega prostora: 5.360 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 350 mm, skupna širina: 2.550 mm, Oprema: ABS, Equipment: * 40 mm jaw coupling * height-adjustable towing eye * drop-down side panels * storage box * removable tailgate * towing eyes * BPW axles Hfjdpfx Ajy Si Etjg Ieg * galvanized Other information: * 1 previous owner * German first delivery * Downrated from 11.9 t to 10.0 t without technical modification Since 1972, your reliable partner for all things automotive and commercial vehicles in 28832 Achim at Bremer Kreuz. NutzfahrzeugZentrum Behnke constantly stocks around 200 vehicles from the fields of vans, commercial vehicles, and construction machinery! We continuously offer attractive financing solutions at favourable special rates. If you are interested, we will be happy to provide you with an individual quote! Trade-in of your commercial vehicle/construction machinery is welcome. If a new TÜV inspection is desired, we will gladly provide you with an offer from our partner workshops. Our offer generally does NOT include a new TÜV inspection. Delivery of your "new" commercial vehicle is possible through our external partners for an additional fee. The information provided in advertisements, on the internet, on price tags and in images are non-binding descriptions and do not constitute guaranteed features. The seller accepts no liability or warranty for typographical or data transmission errors. Listed equipment must be checked separately if necessary. Subject to errors and prior sale.

Stanje: rabljeno, največja dovoljena obremenitev: 6.000 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, prva registracija: 04/2026, Oprema: ABS, * Müller Mitteltal KWH 8.8 ML Cable Transport Trailer * LIKE NEW and available * Reference for inquiries: 11652 * TPMS Tire Pressure Monitoring System * EBS brake system, drum brake, BPW axle, parabolic springs * Support winch at front, spring-assisted square tube supports at rear with base plate, safety locking pins for multiple support heights * Drawbar with 40 mm towing eye (height-adjustable in mm) * 15-pin electrical connector * LED lighting * 315/80 R 22.5 tyres, solid steel fenders * Swivel-mounted cable reel assembly * Steel drum shaft with 76 mm diameter, centering and rotating ends * 1 pair of step-tapered polyamide centering cones * For reel diameters Ø 800–3,000 mm x (1,700 mm width between reel arms) Hfodpfxsy R Hx Ue Ag Ijg * With clamp lock for securing the reel at the end of load arms and central claw lock for securing the cable reel assembly to the chassis * Motor-hydraulic, actuated pull and push cylinders with pipe rupture protection. Control valve with auto-centering neutral position, pressure relief valve, and lowering throttle. NW 13 hydraulic system connectors, hoses, and pipes included. * Hydraulically driven reel motor with oil motor, valves, and rubber-coated drive rollers (adjustable). Hydraulic speed regulator and brake for reel drive. * Includes hydraulic pump unit – Hatz 1B30 Silent diesel engine with hand starter, 6.5 HP (150 bar), pressure supply selectable via connection change: truck hydraulics or pump unit * Toolbox approx. 500 x 350 x 400 mm * Hot-dip galvanized chassis with drawbar * Advert space integrated in side guard, exterior polyester-coated in RAL white * ----like-new condition (only used for one project) * ---- * Financing available from our partner banks with or without down payment, balloon payment and different terms possible. Ask us for a quote! * We are an official Müller Mitteltal trading partner! * Lease-purchase example from our partner FM LeasingPartner: starting from just €595/month net, 60 months term (no down payment, €0 final payment). * Ask us for a quote! ---- * Our business hours: * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside business hours, appointments by arrangement * Languages spoken: German, English, Russian, Polish, French ----

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: Hsdpfx Aeq Euakjg Ijfg * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Traction aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for shunting via EBS (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 extra LED reversing lights * 7-pin socket at the rear for additional length lighting * Side marker lights with indicator activation * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the headboard crossmember (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection cables from truck to semi-trailer ----Lowbed platform: * Second kingpin position * Fifth wheel platform with 45° bevelled front corners and front toolbox made of galvanised, powder-coated steel sheet, W = 2,480 mm x H = 500 mm x L = 665 mm with folding lid * Side aluminium drop sides, 400 mm high (in RAL custom colour), foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on the saddle platform to the lowbed approx. 700 mm long with chequer plate covering and a perforated strip at the end for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9 x mechanical folding wideners to 3 m overall width, not in rear slope (widening planks available with sealed crosswise storage compartment under the loading area) * 3 mounting shafts under the saddle platform for the storage of either aluminium loading ramps or wooden planks for wheel well covering ----Load securing (LaSi-package): Hsdjtpta Djpfx Ag Iofg Fifth wheel platform: * Perforated outer frame, 45° angled, with hole pattern for lashings (2 t lashing capacity per tie-down point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the cranking, 1 x above the central axle next to the longitudinal member) Lowbed platform: * 3 x 13.4 t lashing rings per side on the outer frame (1 x at the start of the cranked platform, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 t lashing rings per side (1 x between the front wheel well and 1st axle, 1 x between the 2nd and 3rd axle) * 3 x 5 t lashing rings per side bolted to the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear wheel well) ----Excavator arm rest: * Extended excavator arm rest from end of last rigid axle over steering axle to end crossmember, continuous with internal reinforcing profile approx. W = 770 mm x D rear = 270 mm / D front = 170 mm * 2 x 6.4 t lashing rings per side in the exca

Stanje: rabljeno, največja dovoljena obremenitev: 30.700 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2002, Oprema: ABS, * MüllerMitteltal nizkopodni priklopnik s 4 osmi T40 * 2x krmiljeni vrtljivi osi * Nemška prikolica * pero * hidravlično pomične rampe / levo-desno * deljene preklopne rampe * možnost razširitve Hfodsyuri Eepfx Ag Isg * ABS * BPW osi * 40 t * lastna teža: 9300 kg * osne obremenitve = 10 t na os * popolnoma funkcionalen * pnevmatike v redu

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Brakes: * Wabco EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs – 110 mm wide – with tandem equalizer unit ----Drawbar / Drawbar Eye: Drawbar with 50 mm flanged towing eye and height-adjustable drawbar ----Electrical / Lighting: * 15-pin power connector * LED taillights * RDÜ tire pressure monitoring system ----General Attachments: * Jost landing gear at the front * External folding supports at the rear * Lateral underrun protection * Plastic quarter mudguards Hedpfxsl Th Hws Ag Ijfg ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted bulkhead panel, smooth sheet metal * Side walls made of trapezoidal profiled steel sheet, foldable with board-wall spring assist * Steel rear wall insertable between the ramps, with internal storage in the front when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees with 2 t lashing capacity every 480 mm * Optional installation of 3 t fold-down lashing rings every 600 mm * 1 x 10 t lashing ring in each front and rear corner; multiple holes in the front and rear crossmembers for 1.2 t lashing options * Profifix lashing rail centrally along the longitudinal axis for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-man operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear access slope approx. 860 mm ----Paintwork: * Chassis, drawbar, bulkhead, rear wall, drive-on ramps, and folding supports hot-dip galvanized * Sideboard painting in RAL 9010 pure white * Optional painting of the side walls in a RAL colour for an additional charge * Axles, springs, air tank, flanged towing eye, and landing gear painted in black ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Sample images ----Delivery Time: * Available approx. from calendar week 21/2026

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar / Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Electrics / Lighting: * TPMS (tyre pressure monitoring system) * 15-pin power connector * LED tail lights ----General Attachments: * Jost landing gear at the front * Outward folding rear supports * Tool box made of galvanized steel sheet, approx. 650 x 350 x 320 mm, mounted on the right side (powder-coated black) * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Reinforcement package for drill rig transport on the chassis – loading height +20 mm * 50 mm softwood floor, clamped design * Preparation in front of the front wall for subsequent installation of container locks * Bolted smooth steel front wall * Fold-down trapezoidal-profile steel side walls with board-lift assist * Steel rear wall, slidable between ramps – storage bracket for unused position inside, in front of the headboard * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Front and rear corners each fitted with 1 x 10 t lashing ring; multiple holes for 1.2 t lashing options in front and rear crossmembers ----Ramps: * One-piece, mechanical grate ramps with spring system for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm gap) * Rear access angle approx. 860 mm ----Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ----Paintwork: * Chassis, drawbar, front wall, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks and landing gear painted in a shade of black * Sideboard painting in RAL 9010 pure white Hedpfx Agjpk D D Ho Iefg * Painting of side walls in an individual RAL color available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 10.870 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2025, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2023, Oprema: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----General Attachments: * Jost mechanical landing gear at front * 2 mechanical folding supports at rear * Plastic toolbox, approx. 650 x 350 x 320 mm, mounted on the right side of the chassis at the front * Bolted underrun protection * Plastic quarter mudguards * Net hooks positioned at the central locking locations and 2 on the front wall ----Chassis: * High-tensile steel chassis ----Tipping Platform: * Steel pallet-type three-way tipper body with continuous side walls, upper inside pipe reinforcement, no central stanchions; drop-down with drop side spring assistance * Bolt-on rear stanchions * Combination steel swing doors on the rear wall, 2-leaf, asymmetrically split, can swing and lock 270°, not drop-down, with additional pendulum frame for automatic rear wall opening during tipping; locking via galvanized rotary bolt at the rear and central locking; deactivation for auto rear wall function when tipping backwards with door open * 4 mm fine-grained steel floor plate * Rear mounting rails for loading ramps ----Load Securing: * 1 x 5 t lashing point in each corner, plus 4 x 3 t lashing rings on each side recessed into the external frame Hfodpol Th Htefx Ag Ijg ----Ramps: * 1 pair of aluminium drive-on ramps, approx. 3,570 x 410 mm (load capacity: 10 t/pair), suitable for rubber-tired & tracked vehicles * Lockable storage compartment under the loading platform, integrated into the chassis for the ramps ----Tyres: * Tyres 285/70 R19.5 ----Painting: * Chassis, drawbar, underrun protection, rear stanchions and rear folding supports hot-dip galvanized * Axles, springs, air tanks and support winch painted black * Drop sides painted RAL 9010 pure white * Other RAL-coloured side wall painting available at extra cost ----Information: * Reinforced body with load securing certificate * Vehicle has a day registration (not previously in use) * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: Hsdpfeq Dyvvox Ag Isfg * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General Attachments: * Jost landing gear at the front * External, hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right exterior on the bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet steel bulkhead * Drop sides made of trapezoidal-profiled steel, foldable with drop-side lifting aid * Rear wall made of steel, can be inserted between ramps - storage bracket inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Optional installation of 3 t recessed lashing rings every 600 mm * Each front and rear corner equipped with 1 x 6.3 t lashing ring * Various holes in the front and rear cross members for 1.2 t lashing points * Profifix lashing rail along the center longitudinal axis for securing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, ramps, and rear wall * Drop side color in RAL 9010 pure white * Painting of the side walls in any RAL shade available at extra cost ----Information: * --Reinforced and certified body to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from week 29/2026

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Brakes: * Wabco EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs, 110 mm wide, with tandem compensating aggregate ----Drawbar / Towing Eye: Drawbar with 50 mm bolt-on towing eye and height-adjustable drawbar ----Electrics / Lighting: * 15-pin electrical connector * LED rear lights * RDÜ tire pressure monitoring system ----General Accessories: * Jost landing leg at the front * External folding support legs at the rear * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the front wall for subsequent installation of container locks * Bolted front wall made from smooth sheet metal * Side walls made from trapezoidal profiled steel – foldable, with tailgate spring assist * Rear wall made of steel, slidable between the ramps – storage bracket inside, in front of the front wall when not in use * Bolt-on rear stanchions ----Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing points every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In each corner at front and rear, 1 x 10 t lashing ring; various holes for 1.2 t lashing options in front and rear cross-members * Profifix lashing rail along the center longitudinal axis for lashing points up to LC 3000 daN ----Ramps: * One-piece mechanical grid ramps with spring mechanism for one-person operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear ramp wedge approx. 860 mm ----Paintwork: * Chassis, drawbar, front wall, rear wall, loading ramps and folding supports hot-dip galvanized * Sideboard panels painted in RAL 9010 pure white * Side walls can be painted in any RAL color (surcharge applies) * Axles, springs, air reservoirs, towing eye, and landing leg painted in a shade of black ----Info: * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Sample images ----Delivery time: Hfedpfx Agsl Th Hle Ieg * Available approx. from CW 21/2026

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ---- Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ---- Axles: * 2 x 11 t Gigant axles ---- Suspension: * Air suspension with manual lowering at the rear ---- Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ---- Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * 15-pin power connector * LED tail lights ---- General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm, fitted on the right side (black powder-coated) * Side underride protection * Plastic quarter mudguards ---- Low Loader Platform: * Reinforcement package for drilling rig transport on the chassis – loading height +20 mm * 50 mm softwood floor in clamped design * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal-profiled steel sheet, foldable with board wall spring-assisted lifter * Steel rear wall, can be inserted between the ramps – storage bracket in front of the bulkhead when not in use Hfodpfxjpk D Ncj Ag Isg * Rear stakes bolted ---- Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * Each front and rear corner with 1 x 10 t lashing ring; various holes in the headboard and end cross member for 1.2 t lashing options ---- Ramps: * One-piece mechanical steel grating ramps with spring assistance for one-man operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear access slope approx. 860 mm ---- Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ---- Painting: * Chassis, drawbar, headboard, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing leg painted in black * Side boards painted in RAL 9010 pure white * Side walls can be painted in any RAL color for a surcharge ---- Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ---- Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with compensating unit ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * TPMS (tire pressure monitoring system) * LED lighting ----General attachments: * Jost landing leg at the front * Externally mounted, hot-dip galvanized drop-down support legs at the rear * Plastic toolbox, mounted front right on the bulkhead * Side impact protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Preparation in front of bulkhead for retrofitting container locks * Bolted bulkhead in smooth sheet metal * Trapezoidal profile steel side walls, foldable with side wall spring assist * Steel rear wall, slidable between the ramps – storage bracket inside the bulkhead when not in use * Screwed-in rear stanchions ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t recessed lashing rings possible every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in front and rear cross members for 1.2 t lashing options * Profifix lashing rail along the longitudinal axis (center), lashing option up to LC 3,000 daN ----Ramps: * Single-piece mechanical mesh approach ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (can be collapsed down to 20 mm) * Rear drive-up angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, ramps, and rear panel * Side wall color RAL 9010 pure white * Painting of the side walls in a different RAL color available at extra cost Hfodervvflepfx Ag Ieg ----Information: * --Reinforced and certified construction according to EN 12642 XL, including load securing certificate-- * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. week 29/2026

Stanje: rabljeno, največja dovoljena obremenitev: 10.870 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2025, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2023, Oprema: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer set ----Drawbar / Flange eye: * Height-adjustable drawbar (300 mm adjustment range) with 40 mm flange eye ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----General attachments: * Jost mechanical landing gear in front * Two mechanical folding supports at the rear * Plastic toolbox approx. 650 x 350 x 320 mm mounted on the right side at the front of the chassis * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks located at the central locking mounting points as well as 2 hooks on the front wall ----Chassis: * Chassis fabricated from fine-grain steel ----Tipper body: * Steel pallet three-way tipper body with continuous side walls, upper sections internally reinforced with pipe, no central stanchions, drop-side design with tailgate spring lifters * Rear stanchions bolted * Combination steel wing doors at the rear, double-leaf, asymmetrically divided, can swing open and lock to 270°, not collapsible, fitted with additional pendulum frame for automatic tailgate opening during tipping operation; locking by galvanized rotary bar at the rear and central locking; deactivation for automatic tailgate function when tipping backward with open wing doors * 4 mm fine-grain steel floor plate * Rear mounting rails for loading ramps ----Load securing: * Each corner fitted with one 5 t lashing ring, each side fitted with four 3 t recessed lashing rings in the outer frame ----Ramps: * One pair of aluminum access ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tired & tracked vehicles * Rear lockable storage compartment for ramps integrated underneath the load area in the chassis ----Tyres: * Tyres 285/70 19.5 ----Paintwork: * Chassis, drawbar, underrun protection, rear stanchion, and rear support legs hot-dip galvanized * Axles, springs, air reservoirs, and landing gear painted in a shade of black * Side wall paintwork in RAL 9010 pure white * Other RAL color tones for side walls available at extra cost Hfedpfol Th Dusx Ag Iog ----Additional Information: * Reinforced body with load securing certificate * Vehicle comes with one-day registration (never used) * Subject to errors and prior sale ----Delivery time: Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 13.900 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2008, naslednji pregled (TÜV): 09/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 850 mm, prostornina tovornega prostora: 10 m³, skupna širina: 2.550 mm, skupna višina: 2.580 mm, Leto izdelave: 2008, Oprema: ABS, Müller-Mitteltal Three-Sided Tipper 2-Axle Tandem Trailer VIN: 051973 Chassis / Attachments: * Air suspension * 2 x BPW Eco Plus axles with drum brakes * Tyres: 385/65 R 22.5 * Remaining tyre tread: front approx. 20/80%, rear approx. 30/80% * Fixed underrun protection * Drawbar with 50 mm towing eye * 1 x Jost support leg on drawbar Body: * Müller-Mitteltal three-way tipper body * 850 mm aluminium side walls * Front wall and tailgate 960 mm * Approx. 10 m³ * Pallet-wide Weights: * Gross weight 18,000 kg * Payload 13,900 kg * Unladen weight 4,100 kg Hfjdpfx Asy H Trysg Ijg Miscellaneous: * German registration * SP 03 / 2027 * 1 previous owner New general inspections / safety checks or adjustments to gross weights (down- or upgrading) are possible on request. We are happy to assist with export/temporary licence plates, as well as the transport of your purchased vehicles within Germany. Contact us! ---- We speak the following languages: German, English and Russian! ---- No liability for printing or typographical errors. Subject to change, prior sale and mistakes! ---- Who are we? Leible Nutzfahrzeuge is a family-owned company based in Kehl am Rhein. With our many years of experience in the preparation and sale of commercial vehicles, we are a reliable partner for customers worldwide. Leible Nutzfahrzeuge’s particular strength lies in the sale of new and used commercial vehicles. On 11,000 sqm, you will find a wide range of vehicles. Our company philosophy is characterised by fairness and integrity. As customer satisfaction is very important to us, we offer our customers an excellent all-round service package and provide them with a competent contact person who accompanies them in the purchase or sale of vehicles. See for yourself! Our services for you: Vehicle loading We are happy to assist you in loading your purchased vehicles. Organisation of special transports We support you in organising special transports. Day registration / Export licence plates We can arrange export or temporary number plates for you. Handling customs formalities We are pleased to assist you with customs matters.

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-ER 19.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering device ----Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye, height-adjustable by 110 mm via offset plate ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * LED tail lights 12/24 Volt ----General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right side * Side underrun protection * Plastic quarter mudguards ----Low-loader Platform: Hfjdpomi Tmaofx Ag Iog * Reinforcement package on chassis for drilling rig transport * 50 mm softwood floor, clamped type * Preparation in front of front wall for retrofitting container locks * Bolted smooth plate front wall * Split steel side walls – trapezoidal profile – foldable with central folding stanchion * Steel rear wall slide-in between ramps – bracket for storage in front wall when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45-degree angled, with 2 t lashing force every 480 mm * Option for installation of 3 t drop lashing rings every 600 mm * Lashing package: 1 x 10 t UVV lashing ring in each front and rear corner, 2 x 8 t UVV retractable lashing rings each side in the outer frame, various holes for 1.2 t lashing options in the front and rear crossmembers ----Ramps: * One-piece slide-in ramps 12 t/pair, ramps approx. 2,750 x 620 mm * Rear approach angle approx. 860 mm ----Loading Height: * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm ----Tyres / Wheelbase: * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 ----Paintwork: * Chassis, drawbar, front wall, rear flap, folding supports and access ramps hot-dip galvanized * ---Axles, air tanks, flange towing eye and landing leg painted in a shade of black--- * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf