Müller-Mitteltal T4, Luftfed., Hydr. Klapprampe, Baggerstiel. nakup rabljenega (3.756)

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: Pgodpsylfvmjfx Ab Hsn * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lowering system, including RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Support legs at the front and mechanical swivel supports at the rear of the chassis * Straight pressed steel fenders * Spare wheel holder under the chassis, right side ----Low Loader Deck: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the fifth wheel platform, foldable and removable * Rear board plug-in, 150 mm high * Rear slope on fifth wheel platform to low-bed approx. 700 mm long * Fifth wheel platform with 50 mm timber planks, low-bed deck with 60 mm timber planks * Tread plate above the axles ----Widenings: * 8 x mechanical folding extensions to a total width of 3 meters (not on rear slope; extension planks available with storage on the platform) * Mechanically adjustable warning panel sets front and rear ----Load Securing (Lashing Package): * On the fifth wheel platform: 2 x 6.3 t lashing rings on each side, plus 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side, plus 4 x 10 t lashing rings, pivotable and lowerable, recessed in the outer frame * 2 x 6.4 t lashing eyes per side, plus 1 lashing ring at the excavator arm rest * 2 x container locks directly after the neck in the low-bed platform ----Excavator Arm Rest: * Continuous excavator arm rest from end of last fixed axle over steering axle to end crossbeam, with internal reinforcements, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanical one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * Outer board on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope * Rubber matting on ramp and approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump performance in the truck between 40 l/min and 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Fifth Wheel Height: * approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Coating: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, support legs, air tanks painted in a black shade * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted Psdpfoy Ngzyex Ab Hegn * Sample images may show equipment not included with the offered vehicle ----Delivery time: * available from c

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle hydraulically steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lower function as well as RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED flashing beacon, rear left ----General attachments: * Side underrun protection * Landing gears in the front and mechanical swing supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder mounted on the chassis, right-hand side ----Low-loader platform: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel, width = 2,480 mm x height = 500 mm x length = 665 mm, with folding lid * 400 mm high aluminum sideboards (RAL 9010 pure white) on both sides of the fifth wheel platform, foldable and removable * Rear wall – 150 mm high, slotted in * Rear slope on the fifth wheel platform down to the low-bed area, approx. 700 mm long * Fifth wheel platform fitted with 50 mm wooden planks, low-bed area with 60 mm wooden planks * Tread plate above the axles ----Width extensions: * 8 x mechanical folding width extensions to a total width of 3 m, except in the rear slope area (extension planks available with storage on the fifth wheel platform) * Mechanically adjustable warning sign packages front and rear ----Load securing (lashing package): * On the fifth wheel platform, 2 x 6.3 t lashing eyes each as well as 3 x 5 t lashing bars on each side in the outer frame * In the low-bed area, 2 x 13.4 t lashing rings on each side as well as 4 x 10 t lashing rings, swiveling and retractable, integrated into the outer frame * 2 x 6.4 t lashing eyes on each side and 1 lashing eye at the rear in the excavator trough * 2 x container locks directly after the kick-up section in the low-bed platform ----Excavator trough: * Excavator trough from end of last rigid axle over steering axle up to the end brace, continuous, with internal reinforcement profile, approx. L = 2,450 mm x W = 770 mm x D = 270 mm ----Ramps: * Mechanically single-piece, hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * The outer board of the ramp is made from 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacities in the truck from over 40 l to 120 l/min) ----Loading dimensions: * Loading area of fifth wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Coupling height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) Pgedel Tnvgjpfx Ab Hen ----Paintwork: * Chassis, ramps, rear swing supports, extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in black tone * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may contain equipment not included with the offered v

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation at rear * Side underrun protection * Pivoting supports at the rear on chassis frame * Mechanically adjustable warning sign packages front and rear * Front closed plastic mudguards and rear straight galvanized steel skirts, each with splash protection * Reflective contour tape on sides and rear * Fold-down (hot-dip galvanized) lid for toolbox on the turntable platform * Multi-voltage system Pgodpfx Absl Th Ads Hjn * LED tail lights * Removable rotating beacon at rear * Drawbar with 40 mm draw eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * 4 stake pockets on each side (stakes not included), with simultaneous lashing facility * Load securing package (La-Si-Paket) comprising: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform, 5 pairs of UVV-compliant lashing rings, swiveling and lowerable, loadable in all directions and recessed into outer frame - in the corners rated to 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not in rear inclined section) * Extension boards stowed in the center of the loading area * Excavator arm rest over rear axle up to end crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator arm rest) * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) * 4-way control block for future retrofitting of hydraulic ramp shift * Mechanical lateral ramp shift * Loading area above turntable: approx. 1,960 x 2,520 mm * Unloaded loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unloaded loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tank, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible gross weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves Podpjylfvgefx Ab Hsgn ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with equalizing unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with in-cab display via EBS signal—no in-cab installation required * 15-pin power connector * LED lighting system, 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * External folding rear support legs * Plastic toolbox approx. 858 x 500 x 500 mm, front right, mounted externally on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Provision in front of the bulkhead for retrofitting container locks * Bolted 400 mm smooth steel bulkhead * Bolted rear stanchions * Side walls with spring assist ----Load Securing: * Perforated outer frame, angled at approx. 45°, with 2 t lashing capacity every 480 mm * Option to install 3 t drop lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing points * Profifix lashing rail along the centerline for lashing capabilities up to LC 3000 daN ----Ramps: * One-piece hydraulic grating ramps, approx. 2,750 x 600 mm (can be compacted to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump performance in the truck of over 40 l/min up to max. 140 l/min) ----Paintwork: Pedpfx Aberwc R As Hsgn * Chassis, drawbar, bulkhead, mechanical drop supports, and ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange towing eye painted in a black shade * Side wall paintwork in RAL 9010 pure white * Painting of the side walls in an RAL color of choice available at an extra charge ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Sample images shown ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle trailing steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift-and-lower function and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an infotool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Landing gears at the front as well as mechanical swing-down supports at the rear of the chassis * Straight sheet steel mudguards * Spare wheel holder under the chassis on the right side ----Low Loader Deck: * Gooseneck platform with 45° chamfered front corners and front toolbox made of galvanized sheet steel W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the gooseneck, foldable and removable * Rear wall – 150 mm – fitted * Rear slope at the gooseneck platform to the low-bed approx. 700 mm long * Gooseneck platform with 50 mm timber planks, low-bed platform with 60 mm timber planks * Tread plate over the axles ----Extensions: * 8 x mechanical fold-out extensions to 3 m total width, but not on the rear slope (extension planks present with storage on gooseneck platform) * Mechanically adjustable warning sign packages front and rear ----Load Securing (Lashing Package): * On the gooseneck platform: 2 x 6.3 t lashing rings each side and 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform sides: 2 x 13.4 t lashing rings each, and 4 x 10 t swivel and lowerable lashing rings recessed in the outer frame * 2 x 6.4 t lashing eyes per side and rear 1 lashing ring in the excavator arm recess * 2 x container locks directly after the gooseneck in the low-bed platform ----Excavator Arm Recess: * Excavator arm recess from end of last rigid axle, over steering axle to end crossmember, continuous, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Loading Ramps: * Mechanically one-piece hot-dip galvanized hydraulic loading ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer retrofit of hydraulic ramp shifting * The outer board of the ramp consists of 50 mm hardwood * Climbing strips on the outer frame of the ramp as well as on the drive-up slope * Rubber on the ramp and drive-up slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck from 40 up to 120 l/min) ----Loading Dimensions: * Loading area, gooseneck platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm drive-up slope) ----Fifth Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, loading ramps, rear folding supports, extension brackets hot-dip galvanized * Axles, landing gears, air reservoirs painted in a black tone * Vehicle is hot-dip galvanized ----Information: Psdsy Ngz Hepfx Ab Hsgn * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Sample images may include features not part of the offered vehicle * Sample images ----Delivery time: * tba

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalizer * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign kits at the front and rear * Front: closed plastic mudguards, rear: straight galvanized steel mud flaps, each with splash guards * Contour marking tape, reflective, on sides and rear * Foldable (hot-dip galvanized) tool box cover on the turntable platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * Four stake pockets each side (no stakes included), also suitable for lashing * Load securing package consisting of: 2 lashing points (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions and recessed into the outer frame (13.4 t in corners, otherwise 10 t) * 6 pairs of mechanical folding outriggers for total width of 3 m (not in the rear slant) Pjdjx Ipa Nepfx Ab Hsgn * Widening planks stored in the center of the loading area * Excavator arm support over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides in the excavator arm support) * Mechanical one-piece ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanically adjustable lateral ramp displacement * Loading area above the turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach incline) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Gross technical weight of 30,000 kg possible -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle with steering function and electro-pneumatic steering lock ----Suspension: * Air suspension with lifting/lowering system and RtR valve ----Electrics / Lighting: * Tire pressure monitoring system (TPMS) Pgodpfx Aspk D I Aeb Hjn * Smartboard operator panel mounted on the trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon at rear left ----General attachments: * Side underrun protection * Landing legs at the front and mechanical swing supports at rear of chassis * Straight steel mudguards * Spare wheel carrier mounted under chassis, right side ----Low-loader platform: * Gooseneck platform with 45° chamfered front corners and tool box at the front made of galvanized steel, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm high aluminum side boards (RAL 9010 pure white) foldable and removable, along the sides of the gooseneck platform * Rear panel 150 mm high, plug-in * Rear slope on the gooseneck platform leading to low-bed, approx. 700 mm long * Gooseneck platform with 50 mm wooden planks; low-bed platform with 60 mm wooden planks * Tread plate over the axles ----Extensions: * 8 x mechanical folding extensions to a total width of 3 m (not on the rear slope, extension planks available with storage on gooseneck platform) * Mechanically adjustable warning panel sets, front and rear ----Load securing (Lashing package): * On the gooseneck platform: 2 x 6.3 t lashing rings per side and 3 x 5 t lashing bars per side on the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side and 4 x 10 t lashing rings, swivel and lowerable, embedded in the outer frame * 2 x 6.4 t lashing eyes per side and 1 lashing ring at the rear, in the excavator-arm recess * 2 x container locks immediately after the step in the low-bed platform ----Excavator-arm recess: * Continuous from the end of the last rigid axle over the steering axle to the end cross member, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Access ramps: * Mechanical one-piece, hot-dip galvanized hydraulic access ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * Quadruple control block for future retrofitting of hydraulically lateral shifting ramps by customer * The outer plank on the ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output of 40 up to 120 liters/min in the truck) ----Loading dimensions: * Gooseneck platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen: approx. 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paint/Finish: * Chassis, access ramps, rear folding supports, and extension brackets are hot-dip galvanized * Axles, landing legs, and air reservoirs are painted in a shade of black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Sample images may show equipment not included in the offered vehicle ----Delivery time: * Available from week 38/2026

Stanje: novo, največja dovoljena obremenitev: 23.830 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical rear axle compensation * Side underrun protection * Rear swivel supports on chassis frame * Mechanically adjustable warning panel sets front and rear * Front closed plastic fenders and rear straight galvanized steel skirts, each with splash protection * Contour tapes on sides and rear, reflective * Hinged lid (hot-dip galvanized) for tool box in the bogie platform * Multi-voltage system * LED tail lights * Removable beacon at the rear * Tow bar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * Four stake pockets each side (no stakes present) with simultaneous lashing options * Load securing package consisting of: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV-compliant lashing rings - swiveling and retractable, loadable in all directions and integrated in the outer frame – 13.4 t at the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (not on rear taper) * Widening planks stored in the center of the loading platform * Excavator arm rest over rear axle up to the rear cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings fitted laterally in the arm rest) * Mechanically operated one-piece loading ramps with spring assembly (approx. 3,000 x 720 mm) * Mechanical lateral ramp adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm drive-on slope) * Chassis, bogie, tow bar, and loading ramps hot-dip galvanized * Axles, springs, air tank, etc., painted in black * 235/75 R17.5 twin tires * 5,900 kg curb weight * --Permissible total weight of 30,000 kg technically possible-- Pgsdex Ipavepfx Ab Hsn * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 23.900 kg, skupna masa: 31.000 kg, konfiguracija osi: 2 osi, prva registracija: 06/2007, Leto izdelave: 2007, Interna številka vozila: G400178 Na voljo takoj na naši lokaciji v Kaufungenu Več informacij: Pgsdozahg Djpfx Ab Hon * Golec Nutzfahrzeuge GmbH (nemško, angleško, bolgarsko, rusko) * Viktoria Sologubova (poljsko, rusko, ukrajinsko, angleško) Lastna teža: 7.100 kg Skupna dolžina: 10.800 mm Največja dovoljena masa: 31.000 kg Možne so napake pri vnosu podatkov Z veseljem vzamemo vaše rabljeno vozilo v račun. Financiranje možno neposredno pri nas. GOLEC NUTZFAHRZEUGE GMBH Govori se: nemško, angleško, špansko, poljsko, ukrajinsko, rusko, bolgarsko.

Stanje: rabljeno, največja dovoljena obremenitev: 27.300 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2013, naslednji pregled (TÜV): 08/2026, dolžina tovornega prostora: 11.700 mm, širina tovornega prostora: 3.000 mm, skupna širina: 2.550 mm, skupna višina: 3.700 mm, Oprema: ABS, * Gugalnica z zaboji za shranjevanje * Sledilne krmiljene osi Pgodpfeza Rliex Ab Hjn * Hidravlične nakladalne rampe * Razširljiva nizkopodna ploščad ----* Dimenzija pnevmatik: 235/75R17,5 * Tehnična skupna masa: 42.000 kg * Lastna teža: 8.700 kg * Skupna dolžina: 13.150 mm * SP veljavnost do: 02/2027 ----Številka vozila: 12148 ----Možne napake in vmesna prodaja pridržane ----Oglasi in različni napisi so bili digitalno odstranjeni. -----Z veseljem vam pomagamo pri vseh formalnostih, ki nastanejo ob nakupu vozila – sporočite nam vaše želje in predloge ter za vse ostalo bomo poskrbeli mi. Med drugim vam lahko za doplačilo ponudimo naslednje storitve: ----Odkup vašega starega vozila TÜV/SP tehnični pregled Popolna izvozna obdelava Posredovanje financiranja Urejanje izvoznih tablic Prevoz vozil Registracija vozil Reševanje in transport vozil ----VAŠ VTS TEAM

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear Pgedpfx Abjxmpykj Hon * Warning sign packages front & rear * SmartBord infotool installed with pressure sensors for displaying axle group loads * Reflective contour tape on the sides and rear * LED beacon (removable) at the rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front enclosed individual plastic mudguards * Rear straight steel mudflaps with spray suppression * Side underrun protection * Extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments with lockable folding lids (folding lids open towards the rear) * Chassis made from high-strength fine-grain steel * Floor over bogie platform made of 50 mm softwood, and in the low-bed platform made of 60 mm softwood * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t each at the front left and right on the main frame of the bogie platform; one pair of 13.4 t lashing rings at the front and rear sides of outer frame; one pair of 10 t lashing rings on each side foldable and lowerable, loadable in all directions, integrated into the side frame; 5 t bolted lashing rings on the outer frame of the wheel recesses (2 per front wheel recess, 1 per rear); 2 pairs of 6.4 t lashing rings at the excavator stick compartment * 11 pairs of fold-out outriggers for overall width of 3 m (not on the rear incline) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for width-extension planks, steel, mounted crosswise to the loading area in front of the first rear axle * Excavator stick compartment above the rear axle extending to the end of the ramp incline, approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on bogie platform) for transporting wheel loaders with wheelbase 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulic extendable tip, approx. 4,650 x 720 mm * Hydraulic sideward ramp displacement * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded deck height approx. 890 mm ± 20 mm (including 860 mm ramp incline) * Chassis, bogie, fold-out outriggers, rear supports, and access ramps fully hot-dip galvanized * Axles, air tanks, and drawbar painted in black shade * Tires: 235/75R17.5 * Vehicle is fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved Pgedpfxsxmpydo Ab Hen * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, PT 30 Profile: ----Braking System: * EBS (electronic braking system) * Emergency release mechanism for spring-actuated cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system, including RtR valve ----Drawbar: * Drawbar, 1,200 mm long, with 40 mm towing eye and height adjustment via traction spring & turnbuckle Pedpfx Absxptn Rj Hegn ----Electrical / Lighting: * Smart-Board information system mounted on the trailer (for axle load indication – separate front and rear display) * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning board sets front and rear * Front axle plastic quarter mudguards with spray protection * Rear axle straight galvanized steel mud skirts with spray protection * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted right side * Compartment in the bogie for accessories, with folding lid and 2 fixed container locks (directly behind the bogie platform) * 2 galvanized steps on the bogie, left and right ----Low Loader Platform: * Robot-welded non-slip overlay on the steel plate of the bogie platform (protruding weld seams) ----Load Securing (La-Si package consisting of): * 2 lashing eyes (13.4 t) front left & right on front bulkhead carrier * 1 pair of UVV lashing rings at front & rear (13.4 t) and 3 pairs of UVV lashing rings on each side (10 t), pivotable and lowerable, loadable in all directions, recessed in outer frame * 3 stake pockets on each side, each with 2 t lashing capacity * Profifix lashing rail in longitudinal axis, centered in flat area, for lashing up to LC 3000 daN ----Widening: * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear taper) * Widening planks stored in the centre of the loading platform ----Ramps: * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm * Mechanically adjustable laterally * 4-way control block for future retrofit of hydraulic ramp lateral adjustment ----Excavator Arm Rest: * Excavator arm rest above rear axle, extending to the rear end crossmember (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator arm rest, located laterally in the main longitudinal frame ----Loading Height: * Loaded approx. 910 mm +/- 20 mm (air suspension) ----Paintwork: * Chassis, bogie, folding outriggers, drop-down supports and ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 23.940 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.460 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * T3 Profi 30.0 ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Parabolic springs with mechanical rear axle compensation ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment via drawbar spring & turnbuckle ----Lighting / Electrics: * TPMS Tire Pressure Monitoring System * Multi-voltage system * LED tail lights 12 / 24 V * Rear removable warning beacon * 15-pin power connector ----General Equipment: * Side underrun protection * Rear swing-down support legs on chassis frame * Mechanically adjustable warning panel kits front and rear * VA closed plastic mudguards in front and straight galvanized steel skirts at the rear, each with spray protection * Tool box made of galvanized steel sheet - black powder-coated - approx. 650 x 300 x 600 mm * Folding lid (hot-dip galvanized) for the toolbox in the turntable platform * Four stake pockets per side (stakes not included), also with lashing function ----Load Securing (La-Si package consisting of): * 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform * 6 pairs of UVV folding and retractable lashing rings, loadable in all directions and countersunk into the outer frame * 13.4 t at corners, 10 t otherwise ----Widening: * 6 pairs of manual folding outrigger arms for 3 m overall width (not on the sloped rear section) * Widening boards stowed in the center of the loading area ----Ramps: * Hot-dip galvanized one-piece hydraulic loading ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * 4-way hydraulic control unit pre-installed for optional hydraulic side shift of ramps ----Loading Area: * Over turntable: approx. 1,960 x 2,520 mm & unladen height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm & unladen height approx. 910 mm (incl. 860 mm entry incline) ----Tyres: * 235/75 R 17.5 twin tyres ----Unladen weight: * Approx. 5,980 kg unladen weight Pgsdpfx Ael Th Nnjb Hon ----Finish: * Chassis, turntable, drawbar and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted black ----Information: * Permissible total weight of 30,000 kg technically possible * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex stock Egestorf

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Brakes: * Without ABS/EBS, approved for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: Psdpfxjr Dpzuo Ab Hegn * Tandem equalization unit with 100 mm wide parabolic springs ----Drawbar / Drawtube: * Fixed welded drawtube with low-maintenance ball joint for K80 ball coupling (offset by +77 mm / 33 mm via head plate), with raised bracket for connection lines ----Electrics / Lighting: * 12 V, 7 + 4 pin power supply * LED lighting system 12 / 24 V with protective grid * 2 LED work lights at the rear, switchable from towing vehicle without installation on towing side ----General attachments: * Support winch at the front * Mechanical drop-down supports at the rear * Side marker lights with indicator activation * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right side * Hot-dip galvanized two-step access ladder in front of the front wall (on FR left) ----Chassis: * Fine-grain steel chassis ----Tipper body: * Steel Pal.- 3-way tipper body with M-Strong side panels (front wall fixed, continuous side panels - without center stanchions - swinging via manual central locking and mechanically foldable with sideboard spring assistor) * Hydraulic tailgate, 500 mm high, functioning as hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load securing: * 1 x 7-tonne recessed and foldable lashing point in each corner * 4 x 3-tonne recessed and foldable lashing rings on each side ----Ramps: * 1 pair of aluminum drive-on ramps (10 t/pair with axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber-tired and tracked vehicles * 2 receiving compartments for aluminum drive-on ramps, recessed from behind into the chassis * Load securing according to EN 12642 XL ----Coupling height: * Laden approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Superstructure painted RAL 9010 pure white * Chassis, drawtube, rear supports, underrun protection hot-dip galvanized * Axles, air tank, support winch at the front * K80 coupling painted in black shade ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Braking System: * Without ABS/EBS, homologated for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: * Tandem-balance unit with 100 mm wide parabolic springs ----Drawbar Eye / Drawbar: * Rigid, welded drawbar with low-maintenance ball joint for K80 ball coupling (adjustable by +77 mm / 33 mm via mounting plate) with elevated gallows for connection lines ----Electrics / Lighting: * 12 V 7 + 4-pin power supply cable * LED lighting system, 12 / 24 V with protective grilles * 2 LED work lights at the rear, switchable from the towing vehicle, no vehicle-side installation required ----General Attachments: * Landing gear at the front * Mechanical drop legs at the rear * Side marker lights with indicator control * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right-hand side * Hot-dip galvanized two-step access steps in front of the bulkhead on the left (FR) ----Chassis: * Chassis made from high-tensile fine-grained steel ----Tipper Body: * Steel pallet three-way tipper body with M-Strong side boards (fixed front wall, continuous sides without central stanchions, swinging via manual central locking, plus mechanically folding with board spring lifters) * Hydraulic tailgate, 500 mm high, engineered as a hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load Securing: * Each corner equipped with 1 x 7 t recessed folding lashing ring * Each side fitted with 4 x 3 t recessed folding lashing points ----Ramps: * 1 pair aluminum loading ramps (10 t/pair for axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber and tracked vehicles * 2 recessed storage compartments for aluminum ramps in the rear of the chassis * Load securing compliant with EN 12642 XL ----Coupling Height: * Loaded approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Bodywork painted in RAL 9010 pure white * Chassis, drawbar, rear support legs, underrun protection hot-dip galvanized * Axles, air tanks, landing gear (front) * K80 coupling painted in black ----Information: Podpfx Asr Dpz Hsb Hjgn * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex works Egestorf

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m Podpfxjw Tgkbs Ab Hogn * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026

Stanje: rabljeno, prva registracija: 11/2006, Leto izdelave: 2006, MÜLLER - MITTELTAL T4 Kompakt Vrtljiva prikolica - Nizkopodna prikolica z zračno vzmetenimi in jamskimi kolesi - 4 x zračno vzmetene GIGANT - osi - zračno vzmetenje - 4 x kolesne jame - mehanske nakladalne rampe - 2 zadnja podporna noga, zložljiva - izvlečne opozorilne table - ABS - MICHELIN pnevmatike: 235/75 R 17.5 - težka izvedba: 40.000 kg skupne mase - lastna teža: 8.400 kg - skupna dolžina: 11.750 mm - vlečna zanka: 50 mm Posebej primerna za prevoz strojev za rezanje apna! Podpfjwmpbdex Ab Hjgn - nemška prikolica - Tehnični pregled / tehnični preizkus možen na zahtevo in za doplačilo! Pridržujemo si pravico do napak in vmesne prodaje!

Stanje: rabljeno, številka stroja/vozila: 110, lastna masa: 8.320 kg, največja dovoljena obremenitev: 31.680 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2008, dolžina tovornega prostora: 10.300 mm, širina tovornega prostora: 2.550 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 r17,5, medosna razdalja: 6.500 mm, barva: modra, Oprema: ABS, * Drum brake * 4 axles * Wheelbase 6,500 mm * Hydraulic ramp length 2,850 mm – width 650 mm * Loading edge height 920 mm Pgedpfx Ajlpav Uob Hen * Extendable to 3 m Subject to errors and omissions

Stanje: rabljeno, lastna masa: 9.300 kg, največja dovoljena obremenitev: 14.700 kg, prva registracija: 02/2001, naslednji pregled (TÜV): 10/2024, skupna širina: 25.500 mm, vzmetenje: jeklo, velikost pnevmatike: 235 / 75 R 17.5 / 10mm, velikost sprednje pnevmatike: 235 / 75 R 17.5 / 10mm, obratovalna teža: 24.000 kg,

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve ----Electrics / Lighting: * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: Pgedsq Euakepfx Ab Hjn * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: rabljeno, številka stroja/vozila: 39500, lastna masa: 8.250 kg, največja dovoljena obremenitev: 31.750 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/1995, velikost pnevmatike: 235/75 r17,5 zwilling, barva: oranžna, Further information Main and outer frame made of high-strength double-T sections, grade ST 52.3, quadruple longitudinal profiling, with high-webbed front and rear cross-members as well as transverse braces; frame behind the bogie passage features a gently sloping stepped offset and rear loading bevel, 0.8 m long; lowest possible floor height achieved by recessed wheel wells above the rear wheels; leading edges of the bogie platform beveled at 45 degrees. Two recessed UVV lashing rings each on the bogie platform and loading bevel for attaching securing devices. Rear end fitted with wide supports for a ramp shaft with six-fold bearings. Lateral side protection fitted with an EC-compliant guard rail, wheel chocks with clamp lock. Low-maintenance inclined roller bearing axles with automatic linkage adjusters, two-line pneumatic braking system in accordance with EC regulations, and parking brake. Bogie and drawbar: Constructed from double-T sections in welded design with ball-bearing turntable; standard drawbar length 1,500 mm, with 8 eyelets (50 mm diameter each), drawbar support with threaded spindle as height adjustment device. Vehicle is not fitted with axle compensation! 24 volts, 2 exchange-proof 7-pin connection cables, large rectangular four-chamber lights including rear fog and reversing lights, front distribution box, rear outline marker lights, side marker reflectors, and holder for single-line license plate. Undercarriage made of 40 mm thick, pressure-impregnated pine. Low-loader platform and loading bevel with cross-laid top flooring, 30 mm thick, running lengthwise. Total floor thickness 70 mm. Bogie platform with longitudinal single-layer flooring and recessed open tool box, size L 700 x W 800 x H 180 mm. Pedpfx Asi Rixgeb Hegn Ramps: Welded construction with trough plate, transverse braces, longitudinally laid wooden overlay, 50 mm thick; ramp tips reinforced; ramp holding rods with turnbuckle and safety catch; ramps laterally adjustable by 470 mm each, with perforated rail and sliding tube; ramp shaft made of bright steel, articulated spring lifters with external and internal springs for easy one-person operation, with automatic ground supports. Shot-blasted with steel granulate, zinc phosphate-primed, painted in a single acrylic RAL color of choice; wheels silver. Available in traffic, light, and metallic colors as well as two-tone paint finishes; wood surface is stained.

Stanje: novo, največja dovoljena obremenitev: 37.560 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW axles * Start assist for shunting purposes on the first axle, activated via EBS (without truck-side installation) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes from the driver’s cab via EBS (without truck-side installation) ----Suspension: * Air suspension with lift and lowering function as well as RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lamps with indicator function * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) ----General Attachments: * Side underrun protection * Support legs at the front and swing-down supports at the rear of the chassis Pgjdpfsykx Nksx Ab Hsn * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swing arm as a carrier for connecting lines from truck to semi-trailer ----Low Loader Platform: * 2nd king pin position * Gooseneck platform with 45° chamfered front corners and front-mounted toolbox made of galvanized, powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (in desired RAL color) foldable and removable along the gooseneck platform * Rear wall, insertable, height 150 mm * Rear incline on the gooseneck platform to the low-bed approx. 700 mm long with checker plate covering and at the end a perforated strip for attaching aluminum approach ramps * Gooseneck platform with 50 mm clamped wooden planks, low-bed platform with 60 mm clamped wooden planks * Tread plate over axles * 9 mechanical extension panels to a total width of 3 m, not included in the rear incline (extension planks available with closed transverse stowage compartment under load floor) * Preparation for 3 storage recesses under the gooseneck platform for optional storage of aluminum approach ramps or planks for covering wheel recesses * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Gooseneck platform: * Perforated outer frame, 45° angled, with hole pattern for lashing devices (2 t lashing capacity per point with a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor per side (1 x on gooseneck platform, 1 x on longitudinal frame after the cranking, 1 x above middle axle next to longitudinal frame) Low-bed platform: * 3 x 13.4 t lashing rings per side at the outer frame (1 x start of gooseneck cranking, 1 x start of approach ramp, 1 x end of approach ramp) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side screwed to outer frames of the wheel recesses (2 at front wheel recess, 1 at rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last rigid axle over the steering axle to the end cross member, continuous with internal reinforcing profile approx. W = 770 mm x T rear