Polpriklopnik s ploščadjo

4x FLIEGL SDS 380

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 27.000 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.300 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 235/75 R17.5, barva: siv, obratovalna teža: 11.000 kg, Oprema: ABS, Chassis: - Welded steel frame construction with front and rear frame cranks and a lowered bed without rear chamfer - Neck and kingpin plate 225 mm - Lowered bed rated for 25 t point load over 5 m - Outer frame closed to the outside with welded-on lashing rings for securing - Interchangeable 2" king pin - Rear hook-in rail for aluminum ramps Axles and Tyres: - BPW low-loader axles, each with a 10 t axle load, air bellows diameter 360 mm - Air suspension with lifting and lowering function, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights +100 mm - S-cam brakes 300/200 mm, asbestos-free brake pads - Automatic slack adjusters - IVTM tyre pressure monitoring - 9 tyres 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically forced steered via fifth wheel coupling Floor: - Multi-layer bonded board floor, 27 mm thick, flush with outer frame and longitudinal beams - Underside reinforced with GRP coating - 12 pairs of lashing rings welded in outer frame (8 pairs RUD 8 t – 6 pairs in the lowered bed as well as one pair each on the gooseneck and at the front of the rear aggregate – 2 pairs of 4 t lashing rings on gooseneck and rear aggregate) - 6 pairs of mushroom anchors in outer frame in the lowered bed - Storage box with lid in the lowered bed floor, front left and right Front Wall: - 25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Tarpaulin curtains on both sides with integrated vertical and horizontal belts (approx. 600 mm spacing) and stainless steel tension locks - Adjustable tarp straps (overcentre) up to loading width 4,000 mm including tarpaulin extension with press studs and Velcro fastener - Tarp extension in driving direction: 300 mm, in height: 750 mm - Incl. eyelets for separate tarpaulin extension piece - 1 pair of vertical tarpaulin pockets approx. 1,000 mm long, positioned in the lowered bed at the front crank - With belt pockets Rear Wall: - Steel rear portal frame with side tarpaulin hook-in device - Aluminum double-wing door, 25 mm thick - Both door wings fully foldable with door holders - Each door wing with aluminum double-joint hinge and two recessed grip hollows Front Corner Posts: - Roof height, bolted to front side Central Posts: - 3 pairs of infinitely adjustable folding posts - Posts are movable along the entire length via trolley - Middle posts in the lowered bed also fixable at the rear platform Roof: - EDSCHA sliding roof (galvanized) with cross beams movable in both directions (stacked forward inside the cargo area) - Rear portal cross beam swivels away - PVC tarpaulin roof without customs closure - Manually operated hydraulic lifting roof on both sides, lift 450 mm - Movable lifting roof in positions front (9x50) and rear (9x50), can be driven at increased height - Including tarpaulin extension and apron at rear - Roof can be cranked out 900 mm at front wall Accessories: - Extendable warning signs (removable at front and rear, with socket) incl. position lights up to loading width 4,000 mm - Storage for 4 warning signs on inside of front wall, top right and left - 1 aluminum ladder with holder 2,500 mm long on front wall - 2 rows of self-securing aluminum slats - Metal mudguards with splash flaps Bwedpfjiu Eu Nex Amten - 1 overnight parking plate and 1 ADR plate on rear wall - BEKAMAX central lubrication system with pump and grease class 2 for approx. 35 lubrication points - Electrohydraul

Stanje: novo, največja dovoljena obremenitev: 36.156 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Gross vehicle weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Unladen weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading platform length: 13,600 mm Loaded saddle height: 950–1050 mm Rear steering radius: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360/1,405 mm Overall width: 2,540 mm Technical Description Loading platform: Extendable loading platform with pneumatically operated locking. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of external foldable lashing rings (LC 5,000 daN). 2 pairs of external foldable lashing rings (LC 10,000 daN). Cut-outs in the outer frame of the loading platform for attaching tension belts, LC 2,000 daN. Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (test load 50 t). Axles: SAF axles: SAF CD air suspension axles with disc brakes (377 mm), featuring lifting/lowering function (ET 120). Trailing steering axles with electromagnetic reversing lock, activated via reverse gear or manually. Axle tools. (± 80 kg) Brake system: Brake system compliant with EU regulations, EBS-E (2S2M), without connecting lines to the tractor unit. Chassis: Chassis made from high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) Bwsdpfjg Sk Tvox Amtsn S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and durable corrosion protection of the shot-blasted welded frame provided by a 2-component (2K) zinc dust primer. High-quality 2-component (2K) topcoat, single colour in RAL shade of choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint available. Electrical equipment: Electrical system in accordance with EU regulations. LED lighting, 24V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S, & 15-pin. Connections according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included accessories: At the galvanized front connection bar, yellow-red air couplings. 2 wheel chocks with holder. 2" kingpin. Galvanized steel front wall approx. 2,200 mm high (± 105 kg) EN12642-XL. Yellow reflective tape according to EU regulations on the sides, extension, and rear of the trailer. European reflector plates (red-yellow) on the rear of the trailer. Loading platform with approx. 38 mm thick hardwood floor (± 320 kg). 10 pairs of stake pockets for 100 x 50 mm plug-in stakes on the outer frame of the loading platform (± 30 kg). 1 spare wheel holder under the loading platform, right side in direction of travel. Tyres 435/50 R 19.5 as selected by manufacturer. One mudflap at the rear of the trailer. Manual and documentation on USB stick. Mounting bracket for revolving warning beacon at the rear of the trailer. On the gooseneck and rear panel left and right, each with a bracket for warning plates with socket. One INOX toolbox, cross-mounted under the loading platform (1,000 x 400 x 2,500 mm) (± 135 kg). 6 pairs of WADER container locks in the loading platform for 1x20’ container, 2x20’ containers or 1x40’ container; an additional locking position is provided in the extension for a 45’ container (± 90 kg). 4 pairs of WADER container locks (± 60 kg). 10 pairs of galvanized plug-in stakes, approx. 100 x 50 mm, 1,000 mm high (± 220 kg). 3 pairs of crosswise stake pocket strips mounted in the loading platform for 100 x 50 mm plug-in stakes (± 95 kg). Holder for 1,000 mm stakes (± 45 kg).

Stanje: novo, največja dovoljena obremenitev: 30.540 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.550 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 2.990 mm, skupna širina: 2.550 mm, skupna višina: 1.010 mm, Leto izdelave: 2025, Oprema: ABS, SCHWARZMÜLLER 3-Axle Flatbed Semi-Trailer RH100 – Extendable – For building materials and construction machinery transport NEW VEHICLE Gross weight (technical): 39 t Axle load (technical): 27 t Fifth wheel load (technical): 12 t Empty weight approx. 9 t (+/- DIN tolerance) Flatbed length approx. 13,500 mm = front approx. 4,150 mm, rear approx. 9,350 mm Flatbed width approx. 2,540 mm Loading height front approx. 1,060 mm at coupling height approx. 980 mm, rear 1,010 mm Extendable lightweight steel welded frame construction Extension length approx. 4,000 mm, lockable at intervals of approx. 500 mm Reinforced version for building material transport, 20 t/5m at centre of gravity; construction machine transport up to 20 t (in retracted position) Reinforced U-profile outer frame 6 mm Tapered cross-members 4 mm Bevelled frame at rear, approx. 15°, approx. 500 mm Visual indicator for pneumatic frame locking on both sides, with green control lamp = indicator light for pneumatic frame locking at front left of the fifth wheel Energy guiding chain in central frame Frame locking with integrated lubrication strip 4 pairs of extendable 8 t lashing rings, rear 9 pairs of extendable 10 t lashing rings in outer frame profile, foldable outward on both sides for oversize cargo lashing 10 pairs of lashing mushrooms with welded round steel at lower edge of outer frame 6 pairs of insert sleeves with reinforcement bar for square tube side stanchions 80x50x5 mm (longitudinal, approx. 3 mm clearance), on both sides of outer frame 3 insert sleeve cross-members for side stanchions 80x80 mm, located at central cross-members Insert sleeve cross-members as empty holders for stanchions 6 pairs of sunken container locks for: 2 x 20 ft containers 1 x 20 ft container central 2 x 20 ft containers 1 x 30 ft container Reinforced rear end plate with continuous ramp hanger rail Bsdewfu N Repfx Amtjwn Mechanical 2 x 12 t landing legs, single-sided operation + compensation 2 drop support legs at rear SAF Intradisc B9 axles with 370 mm disc brakes (19.5" discs), Load capacity 9 t/axle, on-road specification Axle spacing 1,310 + 1,410 mm Wheelbase 7,650 mm SAF steering trailing axle with kingpin/bushing approx. 10° steering angle, automatic electro-pneumatic reverse lock, engages automatically in reverse, additional cab switch with release valve Special axle lift on 1st axle, automatic raise/lower depending on weight, with forced lowering, start assist via cab button / "3 x brake" Kilometre counter 6x tyres 435/50 R 19.5, 164J 6x steel rims 14.00 x 19.5 Brake system according to EC Directive 71/320 ECE R13 2-line air brake system, EBS system 2S2M, one axle with sensors RSS/RSP stability programme Spring-loaded parking brake Steel air tanks Air suspension with lifting and lowering device, total stroke approx. 200 mm Automatic ride height 15 km/h Quick release valves SWIT – Schwarzmüller Intelligent Telematics, package "BASIC" Axle load display via EBS CAN bus signal Tyre pressure monitoring according to ECE Regulation 141 35 mm wooden floor, longitudinal over wheels with steel checker plate cover Wooden floor impregnated both sides Reinforced steel front wall approx. 1,800 mm + centre supports integrated into front wall 2 lashing eyes top of corner posts Front steel corner posts integrated into front wall, front (clear side loading length) 24-volt lighting system according to EC Directive 76/756/EWG 2 units full-LED multifunction tail lights "Aspöck" with integrated control unit Flashing LED side marker

Stanje: novo, lastna masa: 10.000 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading Platform: - Gooseneck, length approx. 4,100 mm with central beam - Extendable loading platform, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated hook-on bar for attaching loose ALU approach ramps - Pneumatic locking system with conical locking bolts and reinforced locking positions - Supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles, Suspension, and Tyres: - BPW axles and suspension, all axles hydro-mechanically forced steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tyres 235/75 R17.5, twin-mounted Paintwork: - 6-coat surface treatment - Complete steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paintwork with 2 layers of 2-component (acrylic) paint, single colour in MB 7350 Novagrau, followed by cavity sealing with special wax Steel Structure: - Steel structure made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket at the front connection strip - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets integrated into the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 transverse stake pocket strip mounted in the floor of the gooseneck for stakes approx. 100x50 mm (1x rear on gooseneck) - 2'' kingpin - Mechanical landing legs with 2-speed gearbox and hand crank - JOST Module B – static test load = 50,000 kg - On the gooseneck and loading area, approx. 32 mm wooden flooring in ALU-omega profiles - One locking position on the extension, approx. every 500 mm - 10 pairs of recessed folding lashing rings in the outer frame of the loading area, folding outwards - 6 pairs of stake pockets integrated into the outer frame of the loading area for stakes approx. 100x50 mm - 2 transverse stake pocket strips mounted in the floor of the loading area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Tapered end crossmember of the vehicle, approx. 350 mm 10° - Integrated hook-on bar for loose ALU approach ramps at the rear crossmember of the vehicle - 1 pair of drop tube supports at the rear crossmember - Mudguards on all axles - Central lubrication system with 1 pump - Remote steering from front and rear operable via cable remote control with push button, including single-track monitoring of the axles - Under the gooseneck and at the rear crossmember, left and right, each with a 7-pin socket for warning panels - One 7-pin socket at the rear crossmember - Container locks "TWIST-LOCKS" in the loading area for transport of 2x 20ft and 1x 40ft containers - Radio remote control for rear steering in addition to cable remote control, with 2 indicator lights on the receiver for single-track monitoring - 2 axle load gauges + axle load diagram - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm Bsdpfx Amsiuy Nljtjwn - Standard HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible areas hot-coated in metallic finish using ZIN

Stanje: rabljeno, največja dovoljena obremenitev: 7.350 kg, skupna masa: 10.500 kg, konfiguracija osi: 2 osi, prva registracija: 05/2011, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.440 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Skupna masa: 10.500 kg Bwedsxnhm Sepfx Amtsn Lastna masa: 3.150 kg Nosilnost: 7.350 kg Skupna dolžina: 6.920 mm Nakladalna dolžina: 5.000 mm Širina: skupna širina 2.550 mm / širina nakladalne površine 2.440 mm Višina nakladanja: cca 900 mm Dodatne informacije - Višinsko nastavljiva vlečna oj - 500 mm preklopne stranice - Podporne noge

Stanje: zelo dobro (rabljeno), prva registracija: 03/2021, Leto izdelave: 2021, Oprema: ABS, = Dodatne možnosti in oprema = - ADR - Zračno vzmetenje - Centralno mazanje Bjdpfxey E Hdms Amtown = Dodatne informacije = Lastna teža: 12.360 kg Nosilnost: 43.140 kg Skupna dovoljena masa: 55.500 kg Višina nakladalne površine: 138 cm Tehnično stanje: zelo dobro Optično stanje: zelo dobro Cena: Na zahtevo

Stanje: novo, največja dovoljena obremenitev: 36.565 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.550 mm, skupna širina: 2.550 mm, skupna višina: 1.040 mm, Leto izdelave: 2025, Oprema: ABS, Brand new Kässbohrer SPS Mega heavy-duty platform semi-trailer available immediately! Technical Data: * Fifth wheel height: 950 mm * Platform length: 13,550 mm * Gooseneck: 120 mm * Platform height: 1,040 mm * Wheelbase: 7,700 mm * Axle spacing: 1,360 mm * Overall width: 2,550 mm * Gross technical weight [80 km/h]: 45,000 kg * Gross technical weight [60 km/h]: 46,000 kg * Unladen weight: 7,827 kg Running Gear: * BPW axles with air suspension and disc brakes * Air suspension with load gauge * 1st axle liftable * Wabco braking system * 445/45/R 19.5 tyres Chassis: * Frame made of high-quality, high-strength S700 MC steel, according to ISO 1726 * 2 mm omega-profile reinforced 30 mm hardwood floor * 8x2 sections of side extensions, extendable up to 300 mm * Support winch at front, foldable support legs at rear Ramp: * Ramp mounts at the rear of the vehicle * Rear ramp storage box Load Securing: * Lashing rings * Stake pockets * 6 x 2 pcs. container locking pockets (suitable for 1x20 ft., 2x20 ft., 1x40 ft. container) + 2 x 2 pcs. container locks Bwjdpfxjrukurs Amtjn * Bulkhead made of steel material, 1,500 mm high, with Code XL certificate Accessories: * 1x stainless steel toolbox * Stake box Chassis colour: RAL 3020 Traffic Red For more information, please do not hesitate to contact us.

Stanje: novo, največja dovoljena obremenitev: 36.565 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.550 mm, skupna širina: 2.550 mm, skupna višina: 1.040 mm, Leto izdelave: 2025, Oprema: ABS, Brand-new Kässbohrer SPS Mega Heavy-Duty Platform Semi-Trailer – Immediately Available! Technical Data: * Fifth-wheel height: 950 mm * Platform length: 13,550 mm * Gooseneck: 120 mm * Platform height: 1,040 mm * Wheelbase: 7,700 mm * Axle spacing: 1,360 mm * Overall width: 2,550 mm * Gross vehicle weight rating [80 km/h]: 45,000 kg * Gross vehicle weight rating [60 km/h]: 46,000 kg * Unladen weight: 7,827 kg Chassis: * BPW axles with air suspension and disc brakes * Air suspension with load gauge * 1st axle liftable * Wabco braking system * Tyres: 445/45 R 19.5 Bwjdpjrukt Rofx Amtjn Frame: * Chassis manufactured from high-grade S700 MC steel, compliant with ISO 1726 * 30 mm hardwood floor with 2 mm Omega-profile reinforcement * 8x2 units of side extensions, adjustable up to 300 mm * Landing gear at the front, foldable supports at the rear Ramp: * Ramp mounts at the rear of the vehicle * Rear ramp storage box Load securing: * Lashing rings * Stake pockets * 6 x 2 pcs. container lock pockets (suitable for 1x20 ft, 2x20 ft, 1x40 ft containers) + 2 x 2 pcs. container locks * Steel front wall, 1,500 mm high, with Code XL certificate Accessories: * 1x stainless steel toolbox * Stake storage box Chassis colour: RAL 3020 Traffic Red For further information, please do not hesitate to contact us.

Stanje: dober (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 9.000 kg, dovoljena osna obremenitev (os 2): 9.000 kg, dovoljena osna obremenitev (os 3): 9.000 kg, prva registracija: 05/2019, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, medosna razdalja: 9.400 mm, barva: črn, Leto izdelave: 2019, Oprema: ABS, = Druge možnosti in oprema = - Zračno vzmetenje = Dodatne informacije = Konfiguracija osi Zadnja os 1: dvižna os; Največja osna obremenitev: 9.000 kg Zadnja os 2: Največja osna obremenitev: 9.000 kg Zadnja os 3: Največja osna obremenitev: 9.000 kg Teže Lastna teža: 6.160 kg Nosilnost: 32.840 kg Dovoljena skupna masa: 39.000 kg Funkcionalno Višina nakladalne površine: 132 cm Stanje Bwjdpfx Aoyx Ducjmtjn Tehnično stanje: dobro Vizualno stanje: povprečno Finančne informacije Cena: po dogovoru Dodatne informacije Za več informacij se obrnite na Davida F Middelmana.

Stanje: dober (rabljeno), številka stroja/vozila: SKBS40S30RKE27851, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.550 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 900 mm, Leto izdelave: 2024, = Druge možnosti in oprema = - Zadnje zračno vzmetenje - Sprednje zračno vzmetenje - Sistem kolutnih zavor = Dodatne informacije = Teže Lastna teža: 7.070 kg Nosilnost: 35.930 kg Skupna dovoljena masa: 43.000 kg Bsdpfxoyagk Us Amtewn Stanje Tehnično stanje: dobro Vizualno stanje: dobro Dodatne informacije Stanje prednjih pnevmatik: 50% Prednje pnevmatike: 265/70 R 19.5 Zadnje pnevmatike: 265/70 R 19.5 Zadnji pregled: 2026-01-15 Dodatne informacije Za več informacij kontaktirajte prodajo Lastas.