Polpriklopnik z nizko nakladalno ploščadjo

Wiese SA 36 CS-S Tieflader-Auflieger Plane,Rampe

Stanje: novo, številka stroja/vozila: 56c59c8aba35227ffb44c9f75, lastna masa: 11.350 kg, največja dovoljena obremenitev: 26.650 kg, skupna masa: 38.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Jumbo semi-trailer chassis Steel welded construction with closely spaced cross members, reinforced design, low-bed outer frame profile, suitable for the transport of construction machinery up to 32,000 kg and with a maximum machine width of up to 2,550 mm. Fifth wheel plate with interchangeable 2” king pin. Rear taper approx. 1,200 mm and 7°. Ramp roller closed at the top with steel/chequer plate. In the low-bed area: Omega rail mounted laterally below the outer frame for curtain mounting and as a spacer to the lashing mushrooms, not in the wheel area. For hydraulic lift table: additional fixed lightweight outer frame with Omega profile; lift table can be raised with the tarpaulin closed! 24 t 2-speed landing gear, single-side operation, with semi-circular base and straight mounting plate, load compensation, free rear swing radius approx. 1,950 mm. Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Quarter-round mudguards in front of and behind each axle Anti-spray flaps behind each axle Steel rear underrun protection Full-width rear spray flap 4 stainless steel toolboxes, w=800/h=350/t=350 mm, polished lockable doors, 2x on front left and 2x on front right before the first axle Hydraulic lift table behind gooseneck, approx. 3,000 mm long, hydraulically raisable to drive over the gooseneck, with mechanical locking in raised position (cylinders angled for ground clearance, Fliegl standard). Operation from front right + additional remote control operation (same device as ramp control). Lift table operable with closed tarpaulin! Curtain mounting in the lift table area on a separate lightweight Omega-profile outer frame; lift table operable with closed tarpaulin. Lashing mushrooms usable even when table is lowered! Lashing eyes Gooseneck: 4 pairs of 5 t lashing eyes recessed into outer frame 2 pairs of lashing mushrooms recessed at the top and on the side of the outer frame Low bed 8 pairs of lashing mushrooms (top and side of outer frame), each 10 t 9 pairs of 5 t lashing eyes recessed into outer frame Axles & suspension SAF drum brake axles Last axle self-steering, with automatic reverse lock via reversing light, additional manual locking on vehicle Air suspension with raise/lower valve and auto-reset function Raise/lower function with quick exhaust 1st axle automatic lift axle, including forced lowering and traction aid, activated by 3x braking (traction aid works up to 30% axle overload and max 25 km/h) Axle lift below recommended driving height; therefore, no warranty against tyre damage Bjdpfx Afoi Riw Ao Aocw Wheels and tyres 235/75 R17.5 From leading manufacturers Twin steel rims, factory silver Braking system 2-line compressed air brake system Spring-type parking brake 2 fail-safe coupling heads (front), no connecting line EBS, Electronic Braking System with front EBS socket, no connection cable Note: Trailer may only be towed by tractors that ensure ABS is working! Axle load detection via EBS in truck, without truck installation (not a certified scale) Electrics 24 volt, multi-chamber rear lamps, yellow LED side marker lighting 2 white LED front position lights 2 white/red lane assist rear lights 1 rotating beacon with bracket, switchable via parking light (detachable light) 2 pairs of double LED warning boards, extendable up to 3,000 mm 2 x 7-pin and 1 x 15-pin fail-safe sockets at front, without connecting cable

Stanje: rabljeno, največja dovoljena obremenitev: 36.216 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, prva registracija: 10/2024, naslednji pregled (TÜV): 10/2026, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.100 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, Leto izdelave: 2024, Oprema: ABS, FAYMONVILLE MAX100 3-axle SANH semi low-loader forklift transport trailer First registration 10/2024 Unladen weight approx. 13,200 kg Saddle height 1,150 mm Length of low-bed 9,300 mm Gooseneck length 3,800 mm Internal width 2,480 mm Loading height in low-bed 860 mm Height-adjustable tarpaulin cover, adjustable by approx. 400 mm EDSCHA sliding roof, can be moved forward The body can be hydraulically extended at the rear portal by approx. 750 mm Loading platform after gooseneck hydraulically liftable/lowerable, length approx. 2,800 mm, gooseneck and low-bed with grating flooring, above axles with checker plate and integrated sand coating Two-part steel ramps approx. 3,185 + 1,420 mm, width each 1,250 mm, also with grating surface, max. load 30,000 kg Tyres: 13 pieces, 235/75 R 17.5 BPW axles with drum brakes 1st axle: LIFT AXLE 3rd axle: SELF-STEERING AXLE Air suspension with lifting/lowering function WABCO Trailer EBS E-hydraulics 24 volt Bjdpfox Nlhrjx Af Ascw RENTING is the new BUYING – with us also available immediately as a full-service rental.

Stanje: novo, največja dovoljena obremenitev: 36.461 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, skupna širina: 2.480 mm, skupna višina: 860 mm, Leto izdelave: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm hardwood flooring. Loading Platform: Loading platform after the gooseneck, hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings at the front central beam (LC 10,000 daN). C40/4 grating floor (point load 2.3 t on an area of 20 x 20 cm), over the axles checker plate covering. Two-part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with C40/5 grating (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections, hydraulic lifting system. Max load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length of 16,500 mm when in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF, manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system in line with ECE R 141. Data transmission to the towing vehicle is via the standardised EBS interface according to ISO 11992. The towing vehicle must be able to receive and display this data for correct indication. Axles: BPW axles and suspension, 2 rigid axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with lift and lower valve. Axle tool kit. Brake System: WABCO braking system according to EU regulations with EBS-E (2S2M), without connecting lines to tractor unit. Electrical System: Bsdpfx Aew Dl Hwef Ascw Electrical system according to EU regulations, LED lighting 24 V ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15 pin. Connection in accordance with ISO: 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Steel Construction: Steel construction made of high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Curtainsider Structure: Curtainsider body, ??? 3,960 mm ??? - Galvanised front wall with a tensioning mechanism for sliding curtains. - "EDSCHA" roof, forward sliding on ALU roof beam profiles (bolted to front and rear wall). - 3 pairs of sliding stanchions in the loading platform. - The body is hydraulically extendable at the rear by approx. 750 mm left and right. - Sliding roof with upward folding portal beam. - Sliding curtain with 700 mm length reserve and tie-down straps approx. every 600 mm. Height upper edge of body approx. 3,960 mm (laden). - Driving with an open sliding roof is not permitted and will cause damage to the curtain. Paintwork: Entire steel structure is shot-blasted automatically after welding using a wheel blast system. Second blasting with corundum for optimal coating system adhesion. HRM-metalizing of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection. Final painting with two layers of 2K topcoat, single colour, shade selectable according to RAL 841GL. Rear section metalized and painted RAL 9010 (pure white). No metallic paint.

Stanje: novo, lastna masa: 12.300 kg, največja dovoljena obremenitev: 37.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system Bcjdpfx Aotvfkfjf Aew Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load capacity per pair: 30,000 kg Loading area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering trailing axle - Air suspension with lift and lower valve - The trailing steering axle with electro-magnetic reversing lock, activated by reverse gear or manually - Tyres 235/75 R17.5 3PMSF Included accessories: - 1 spare wheel with holder - TPMS tyre pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holder on the front wall - Rear mounting area on the gooseneck for ALU approach ramps - 3 heights of aluminium planks - Galvanized folding supports under the loading area chamfer - Height-adjustable tarpaulin body (3,960 mm) - Galvanized front wall with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof beam profiles, bolted to front and rear walls - 3 pairs of movable stakes in the loading platform - The superstructure is hydraulically extendable at the rear to the left and right by approx. 750 mm - Sliding roof with high-swivelling portal beam - Sliding curtain with 700 mm length surplus, with tensioning straps spaced approx. 600 mm apart - Height to top of the body: approx. 3,960 mm - Driving with open sliding roof is not permitted and will damage the curtain - Cover plates to bridge the gap between ramps and loading area - Rear electro-hydraulic unit under the loading platform - On gooseneck and ramps, each side with one holder for warning signs including socket - Ramp control valves located on right-hand side of trailer - 6 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - Lift axle on the front axle - Grating surface in the chamfer of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm, mounted on the right side in the direction of travel between the axles - Painted sand layer as anti-slip protection on the chequer plates on the gooseneck and loading area - BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable cover for the pump - Four extendable warning signs (approx. 400 mm each) approx. 423 x 423 mm with position light - Axle load gauge including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, afterwards defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-refined

Stanje: rabljeno, največja dovoljena obremenitev: 31.300 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2019, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.050 mm, skupna širina: 2.550 mm, Oprema: ABS, Meusburger MPG-3 Nizkopodnožno prikolica s ponjavo, krmiljena/dvigljiva os Oprema: zračno vzmetenje * Tehtnica za os * 1. os dvigljiva * 3. os krmiljena * Hidravlična rampa z dodatno podporo in daljinskim upravljanjem * Prehodna rampa * Električni vitel z daljinskim upravljanjem * Edscha streha * Stranski zaboji za shranjevanje * Rezervno kolo s standardno pnevmatiko Bjdpfewfwd Djx Af Ascw * Dodatni žarometi * Izvlečne table za izredne širine Varnost: ABS * EBS * Kolutne zavore Pridržujemo si pravico do napak in predhodne prodaje. Interna številka vozila: 8303

Stanje: rabljeno, največja dovoljena obremenitev: 44.980 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, naslednji pregled (TÜV): 09/2025, skupna širina: 2.550 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt of the equipment list. Complete equipment details available upon request. Chassis, cranked * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, robust outer frame * 4-axle configuration. Wheel arch covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection mounted, made of anodised aluminum * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special design in the cranked area for maximum low-bed length in combination with AluLeg drop supports instead of telescopic landing gears, maximum rear swing radius of the tractor unit approx. 2,100 mm Special superstructure with rear stake extension * Self-supporting aluminium roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable to approx. 4,200 mm * Three sliding stakes per side with spring-assisted tension relief * Additional central stake locks in the roof beam and parking position, operated via pull cord and spring latch * Mechanically height-adjustable roof lift, adjustment height approx. 400 mm, can be operated from either side or single side without needing to open the opposite side and doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with stake height adjustment * Front overlap at bulkhead for driving under tarpaulin up to an overall height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on each side, 450 mm pockets below, above 4 rows of single pockets * In the high bed, only 3 rows of slats. Intermediate distances evenly distributed Bcjdpslthgujfx Af Aew Floor * approx. 27 mm special water-resistant bonded beech plywood, non-slip surface * Steel plate in wheel arch area * Forklift accessible per DIN ? standard * Outer frame surface flush Brakes * WABCO air brake system with EBS complying with EC Directive 71/320 EEC incl. PREV (park-release safety valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer with drum brakes, low loader specification * Air suspension with raise/lower function, total lift approx. 230 mm * Third and fourth axles are friction-steered trailing axles with electrical and mechanical locking Twin tires * 235/75 R 17.5, -16, incl. spare wheel holder. Without spare wheel Paintwork * Chassis in RAL 3002 red, solid color * Central stakes and axles KTL coated black * Corner posts galvanized finish * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork solid color per RAL shade Included special equipment * Air suspension with ECAS control, operated at the trailer * Oversize signage front and rear, galvanized, infinitely extendable, with marker lights incl. plug-in sockets for revolving beacons (small panels) * Additional unlocking for sliding roof frame from outside * 4 stake adapters for special outer frame profile, for flexible locking of central stakes * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, oversize/height version, flat hooks, tarpaulin folds, closures with safety pawl / OCS * Left rear telescopic plug-in socket for revolving beacon incl. beacon * Outer frame for machine transport with approx. 64 securing points in 2,000 kg, 3,000 kg and 10,000 kg versions, according to construction release drawing * 1

Stanje: rabljeno, največja dovoljena obremenitev: 26.100 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2013, naslednji pregled (TÜV): 02/2025, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.000 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, Oprema: ABS, Krebs Mega Curtainsider Semi-Trailer with Dhollandia Tail Lift 9 Tons, Ramp Function * Recently fitted with new tarpaulins; rear and front portal repainted * SAF axles * 1st axle liftable * 3rd axle self-steering (trailing steering axle) * Dhollandia tail lift model DHLSU.90, lifting capacity 9,000 kg, ramp function * Radio remote control * 3 large storage boxes * Work lights * Ice-Protect system For further information, please do not hesitate to contact us. Bcedpfx Asu Em Nnef Aew

Stanje: novo, največja dovoljena obremenitev: 37.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.550 mm, Oprema: ABS, Our complete range of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment features. Full equipment details available upon request. Chassis, dropped frame: * Special high-strength fine-grain steel frame, electrically welded at the joints * Generously dimensioned outer frame * 3-axle configuration * Wheel covers over axles with spray suppression * All steel parts sandblasted * Side underrun protection made from anodized aluminum installed * Increased point load approx. 30,000 kg across approx. 5,000 mm * Special design in the drop area for maximum low-bed length in combination with AluLeg landing gears * Drop legs instead of telescopic support winches, maximum rear swing clearance of tractor unit 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminum roof rail/profile approx. 100 x 100 mm, sliding roof tarpaulin with plastic flaps * Rear stanchions extendable to approx. 4,200 mm (for loading and unloading only) * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks integrated into roof rail with parking position, operated via pull cable and spring bolt * DINKEL mechanically height-adjustable lifting roof * Lifting roof height approx. 400 mm, adjustable on both sides or one side only, without opening the opposite side * Additional height adjustment of approx. 480 mm in steps of approx. 40 mm, adjustable in the stanchions * Front cover panel on bulkhead for driving under tarpaulin at an overall height up to 4,400 mm * Four rows per side of stackable approx. 150 mm aluminum slats, lower section with 450 mm pockets, above that 4 rows of single pockets * In high bed, only 3 rows of insertable slats, evenly spaced Floor: * Approx. 27 mm special waterproof bonded beech plywood, anti-slip surface * Steel plating in wheel arch area. Suitable for forklift traffic as per DIN standard * Outer frame with flush surface Brakes: * WABCO compressed-air braking system with EBS as per EC Standard 71/320 EEC incl. PREV (Parking Release Safety Valve). Spring-loaded brake cylinders for parking brake * Wabco Smart Board with odometer and axle load indicator * Including WABCO tire pressure monitoring Axles: * 3 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower function, total stroke approx. 230 mm * Third axle as friction-steered trailing axle with electric and mechanical lock Twin tires: * 235/75 R 17.5 – 12-ply. Premium brand of our choice, including spare wheel carrier Lighting: * EC-compliant including LED side marker lights * LED position lights * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis with body painted in RAL color (RAL 3002) Bedswx Dcmjpfx Af Ajcw * Central stanchions and axles KTL coated in black * Corner stanchions hot-dip galvanized * Plastic parts in black * Hot-dip galvanized parts unpainted * Wheels in factory silver * Body in single-tone RAL color Special equipment included: * Air suspension in ECAS version, operated on trailer * Central stanchions with additional roof rail latching via pull cable – operated from below * External unlocking for sliding roof frame * 4 stanchion adapters for special outer frame profile, for arbitrary locking of central stanchions * PVC sliding tarpaulins, color SILVER similar to RAL 9006, in over-width and over-height execution, flat hooks, tarpaulin folds, catches with lock

Stanje: dober (rabljeno), obratovalne ure: 4.299 h, dvižna višina: 3.000 mm, Proizvajalec: KALMAR Tip: DCE100-6 Leto proizvodnje: 2010 Nosilnost: 12 t Lastna teža: 16 t Višina dviga: 3 m Bedov D Ixdopfx Af Ajcw Delovne ure: 4.299 h Oprema: Popolna kabina z grelcem, podaljšek vilic 2 m