Polpriklopnik z nizko nakladalno ploščadjo

DINKEL 4-Achs-Jumbotieflader - doppelte Rampen

Stanje: rabljeno, največja dovoljena obremenitev: 44.980 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, naslednji pregled (TÜV): 09/2025, skupna širina: 2.550 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt of the equipment list. Complete equipment details available upon request. Chassis, cranked * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, robust outer frame * 4-axle configuration. Wheel arch covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection mounted, made of anodised aluminum * Increased point load approx. 30,000 kg over approx. 4,000 mm Pedpfx Aolthgujgfepp * Special design in the cranked area for maximum low-bed length in combination with AluLeg drop supports instead of telescopic landing gears, maximum rear swing radius of the tractor unit approx. 2,100 mm Special superstructure with rear stake extension * Self-supporting aluminium roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable to approx. 4,200 mm * Three sliding stakes per side with spring-assisted tension relief * Additional central stake locks in the roof beam and parking position, operated via pull cord and spring latch * Mechanically height-adjustable roof lift, adjustment height approx. 400 mm, can be operated from either side or single side without needing to open the opposite side and doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with stake height adjustment * Front overlap at bulkhead for driving under tarpaulin up to an overall height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on each side, 450 mm pockets below, above 4 rows of single pockets * In the high bed, only 3 rows of slats. Intermediate distances evenly distributed Floor * approx. 27 mm special water-resistant bonded beech plywood, non-slip surface * Steel plate in wheel arch area * Forklift accessible per DIN ? standard * Outer frame surface flush Brakes * WABCO air brake system with EBS complying with EC Directive 71/320 EEC incl. PREV (park-release safety valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer with drum brakes, low loader specification * Air suspension with raise/lower function, total lift approx. 230 mm * Third and fourth axles are friction-steered trailing axles with electrical and mechanical locking Twin tires * 235/75 R 17.5, -16, incl. spare wheel holder. Without spare wheel Paintwork * Chassis in RAL 3002 red, solid color * Central stakes and axles KTL coated black * Corner posts galvanized finish * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork solid color per RAL shade Included special equipment * Air suspension with ECAS control, operated at the trailer * Oversize signage front and rear, galvanized, infinitely extendable, with marker lights incl. plug-in sockets for revolving beacons (small panels) * Additional unlocking for sliding roof frame from outside * 4 stake adapters for special outer frame profile, for flexible locking of central stakes * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, oversize/height version, flat hooks, tarpaulin folds, closures with safety pawl / OCS * Left rear telescopic plug-in socket for revolving beacon incl. beacon * Outer frame for machine transport with approx. 64 securing points in 2,000 kg, 3,000 kg and 10,000 kg versions, according to construction release drawing * 1

Stanje: novo, številka stroja/vozila: 56c59c8aba35227ffb44c9f75, lastna masa: 11.350 kg, največja dovoljena obremenitev: 26.650 kg, skupna masa: 38.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Jumbo semi-trailer chassis Steel welded construction with closely spaced cross members, reinforced design, low-bed outer frame profile, suitable for the transport of construction machinery up to 32,000 kg and with a maximum machine width of up to 2,550 mm. Fifth wheel plate with interchangeable 2” king pin. Rear taper approx. 1,200 mm and 7°. Ramp roller closed at the top with steel/chequer plate. In the low-bed area: Omega rail mounted laterally below the outer frame for curtain mounting and as a spacer to the lashing mushrooms, not in the wheel area. For hydraulic lift table: additional fixed lightweight outer frame with Omega profile; lift table can be raised with the tarpaulin closed! 24 t 2-speed landing gear, single-side operation, with semi-circular base and straight mounting plate, load compensation, free rear swing radius approx. 1,950 mm. Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Quarter-round mudguards in front of and behind each axle Anti-spray flaps behind each axle Steel rear underrun protection Full-width rear spray flap 4 stainless steel toolboxes, w=800/h=350/t=350 mm, polished lockable doors, 2x on front left and 2x on front right before the first axle Hydraulic lift table behind gooseneck, approx. 3,000 mm long, hydraulically raisable to drive over the gooseneck, with mechanical locking in raised position (cylinders angled for ground clearance, Fliegl standard). Operation from front right + additional remote control operation (same device as ramp control). Lift table operable with closed tarpaulin! Curtain mounting in the lift table area on a separate lightweight Omega-profile outer frame; lift table operable with closed tarpaulin. Lashing mushrooms usable even when table is lowered! Lashing eyes Gooseneck: 4 pairs of 5 t lashing eyes recessed into outer frame 2 pairs of lashing mushrooms recessed at the top and on the side of the outer frame Low bed 8 pairs of lashing mushrooms (top and side of outer frame), each 10 t 9 pairs of 5 t lashing eyes recessed into outer frame Axles & suspension SAF drum brake axles Last axle self-steering, with automatic reverse lock via reversing light, additional manual locking on vehicle Ppsdpfji Riw Aox Agfep Air suspension with raise/lower valve and auto-reset function Raise/lower function with quick exhaust 1st axle automatic lift axle, including forced lowering and traction aid, activated by 3x braking (traction aid works up to 30% axle overload and max 25 km/h) Axle lift below recommended driving height; therefore, no warranty against tyre damage Wheels and tyres 235/75 R17.5 From leading manufacturers Twin steel rims, factory silver Braking system 2-line compressed air brake system Spring-type parking brake 2 fail-safe coupling heads (front), no connecting line EBS, Electronic Braking System with front EBS socket, no connection cable Note: Trailer may only be towed by tractors that ensure ABS is working! Axle load detection via EBS in truck, without truck installation (not a certified scale) Electrics 24 volt, multi-chamber rear lamps, yellow LED side marker lighting 2 white LED front position lights 2 white/red lane assist rear lights 1 rotating beacon with bracket, switchable via parking light (detachable light) 2 pairs of double LED warning boards, extendable up to 3,000 mm 2 x 7-pin and 1 x 15-pin fail-safe sockets at front, without connecting cable

Stanje: rabljeno, največja dovoljena obremenitev: 29.690 kg, skupna masa: 37.800 kg, konfiguracija osi: 3 osi, prva registracija: 12/2002, Leto izdelave: 2002, Oprema: ABS, Curtain-sided low-loader Meusburger MPG 3 Dimensions: Length 13.90 m, Width 2.55 m (extendable to 3.50 m with rear posts), Height 4 m Loading dimensions: Platform height 80 cm, internal height in the low-bed area 3.20 m, low-bed to gooseneck height difference 67 cm, internal height in the gooseneck 2.53 m Ppjdswrvubepfx Agfjp Condition: Good for its age Tyres: 205/65R17.5, tread depth 50-70%

Stanje: novo, lastna masa: 12.300 kg, največja dovoljena obremenitev: 37.200 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood flooring Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load capacity per pair: 30,000 kg Loading area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering trailing axle - Air suspension with lift and lower valve - The trailing steering axle with electro-magnetic reversing lock, activated by reverse gear or manually - Tyres 235/75 R17.5 3PMSF Included accessories: - 1 spare wheel with holder - TPMS tyre pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holder on the front wall - Rear mounting area on the gooseneck for ALU approach ramps - 3 heights of aluminium planks - Galvanized folding supports under the loading area chamfer - Height-adjustable tarpaulin body (3,960 mm) - Galvanized front wall with tensioning mechanism for sliding curtain Ppodpjtvfkfjfx Agfjp - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof beam profiles, bolted to front and rear walls - 3 pairs of movable stakes in the loading platform - The superstructure is hydraulically extendable at the rear to the left and right by approx. 750 mm - Sliding roof with high-swivelling portal beam - Sliding curtain with 700 mm length surplus, with tensioning straps spaced approx. 600 mm apart - Height to top of the body: approx. 3,960 mm - Driving with open sliding roof is not permitted and will damage the curtain - Cover plates to bridge the gap between ramps and loading area - Rear electro-hydraulic unit under the loading platform - On gooseneck and ramps, each side with one holder for warning signs including socket - Ramp control valves located on right-hand side of trailer - 6 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - Lift axle on the front axle - Grating surface in the chamfer of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm, mounted on the right side in the direction of travel between the axles - Painted sand layer as anti-slip protection on the chequer plates on the gooseneck and loading area - BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable cover for the pump - Four extendable warning signs (approx. 400 mm each) approx. 423 x 423 mm with position light - Axle load gauge including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Entire steel structure shot-blasted, afterwards defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-refined

Stanje: novo, prevoženi kilometri: 100 km, moč: 375 kW (509,86 KM), vrsta goriva: dizel, skupna masa: 32.000 kg, konfiguracija osi: 3 osi, barva: bela, vrsta prenosa: samodejen, emisijski razred: Euro 6, dolžina tovornega prostora: 9.000 mm, širina tovornega prostora: 2.550 mm, Leto izdelave: 2026, Oprema: ABS, klimatska naprava, navigacijski sistem, parkirni grelec, 4-axle Volvo machine transporter / work platform transporter • FH 500 8x2R • Trailing axle, electro-hydraulically steered, single tires • Rear axle suspension with air suspension: 1 drive axle, 1 trailing axle • FH long-distance safety cab • Cab auxiliary heater, 2 kW • 33 l coolbox with freezer compartment under bunk • Air suspension on the front axle(s) • Transmission/I-Shift operated via control unit on driver's seat • I-Shift drive modes: Standard, Performance, and Economy • I-See with map-based topographical and traffic data • Eco Cruise Control (cruise control) including brake cruise control • Manual gear selection possible in automatic mode (incl. kickdown) • Adaptive Traction Control • Adaptive Cruise Control (ACC) with collision warning & emergency braking • Lane Keeping Assist • Side collision avoidance & turn assist (both sides) • Driver alertness warning system for fatigue • VEB Volvo Engine Brake • etc. WIESE bodywork for aerial platform and construction machinery transport with hydraulic loading ramps with 2 pairs of wheel recesses incl. wheel recess covers Body dimensions: - Usable length approx. 9,050 mm - External width 2,550 mm - Platform height (top of floor) approx. 1,050 mm unladen - Robust, weight-optimized steel welded construction, box-type design - Short crossmember spacing for high point loads - Rear end beveled for low approach angle - External frame profile 90° - Bulkhead in reinforced design - Internal storage box at bottom in front of bulkhead - Grating floor - Designed for 5,000 daN axle load - Above axles: steel toolboxes & outer frame with anti-slip coating Load securing: - 9 pairs of heavy-duty lashing rings, 8 tonnes, flush-mounted in outer frame - Longitudinals each with Multi-X contour along the entire length, many lashing points 2.5 tonnes - 4 lashing eyes 8t at the rear, recessed (left/right/center/center) - 4 lashing eyes 8t at front bulkhead, recessed (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramp design as 2 individual/split ramps, both ramps laterally adjustable - Ramp can be used as a loading ramp or as a drive-over ramp for warehouse technology (sliding part remains closed), fixed ramp section placed on hall ramp - Heavy-duty locking bar for transport security (optional with strap lock) - 2 hydraulic rear supports with plates incl. warning buzzer & indicator light in cab - Ramps and supports operated by electro-hydraulics - Control via radio remote and emergency control at control block - Control block mounted in stainless steel toolbox at side of frame - Superwinch, 8.2 t, with approx. 20 m steel cable Ppodpew Itmlefx Agfep - Access steps with handrails left and right for cargo area access - 5 stainless steel drawer-type toolboxes, incl. lighting (option, at extra cost) - Side fairings as per sample images (green vehicle), option at extra cost - Body coating KTL - Rear tow hitch (ball), 3.3t - 4 LED work spotlights - 2 LED rear lights mounted high on bulkhead - 4 LED external work lights on frame for area illumination - 2 LED work lights at rear - 1 removable rotating beacon at rear The stock vehicle is supplied with cab in white and body in nova grey (outer frame painted to RAL color by request).

Stanje: novo, lastna masa: 10.100 kg, največja dovoljena obremenitev: 38.900 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 245/70 R 17,5, obratovalna teža: 10.100 kg, Oprema: ABS, Chassis: - Sturdy welded steel frame construction with front frame cranking and flat loading platform, rear ramped section approx. 500x100 mm - Gooseneck 200 mm with beveled corners - Sloped gooseneck end approx. 500x100 mm (traction ribs on outer frame behind rear inclination) - 2 kingpin positions with replaceable 2" kingpin - Outer frame closed on the outside as perforated frame for lashing with tension belts (chains not permitted) - Reinforced frame design / point load at the center of gravity - Prepared for extendable load platform widenings - With excavator trough (without cover), depth approx. 220 mm, width approx. 600 mm, starting after 2nd axle to end of vehicle - 1 pair wheel recesses in front of axle with steel covers (covers with Körapur coating), depth approx. 400 mm, and 1 pair between 1st and 2nd axle, steel covers - Underrun protection = extended end plate - Drop-down supports at rear Ramps: - 2-piece drive-up ramps, custom design, with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting mechanism (only in connection with electrohydraulic unit) - Width approx. 800 mm - Wood topping - Incl. traction ribs on ramps - Can be secured for travel with tension belts - Operated by manual lever mounted rear right in direction of travel - Hydraulically laterally shiftable Floor: - 35 mm larch wood floor with aluminum omega profiles Landing Gears: - Mechanical 24 t landing gears, operated from one side with load equalization Axles, Steering, and Tires: - BPW air suspension axles, each rated at 10 t axle load, airbag diameter 360 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lift and lower device, total stroke approx. 200 mm - 2nd drive position via ball valve +50 mm - 1st axle as lift axle (wired via EBS), operation fully automatic with mechanical emergency actuation via button on trailer - 3rd axle as friction steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center-fitted offset - 12 tires 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring Accessories: - Plug-in side walls and rear wall on gooseneck approx. 400 mm high - Spare wheel holder - Lateral aluminum underrun protection - 4 wheel chocks - Long license plate holder in end plate - 1 detachable ECE sign at rear - 11 pairs ZK modules 10t on the sides: - 2x on the gooseneck - 9x on the load platform - Steel mudguards with clear pass - Extendable warning panels incl. 3 position lamps each, front at landing gears and rear before end plate, infinitely extendable up to loading width 4,500 mm Ppedpfewviwkjx Agfop - 4 plug-in holders for warning panels in stake pockets on loading surface - 6 pairs of lateral stake pockets for 100x50 mm stakes - 2 rows of crosswise stake pockets for 100x50 mm stakes on the gooseneck from outer frame towards main frame (1x before and 1x after kingpin positions) - 3 rows of crosswise stake pockets for 100x50 mm stakes on loading platform from outer frame towards main frame (1x in front area, 1x before 1st axle, 1x after 3rd axle) - 2 pairs of steel plates in load platform for container locks to receive 1x 20ft container - Rubber apron mounted on underrun protection - Steel shot blasting, chassis hot-dip galvanized and primed - Chassis/wheel hubs/outer frame painted in DB 7350 Nova grey

Stanje: rabljeno, največja dovoljena obremenitev: 31.300 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2019, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.050 mm, skupna širina: 2.550 mm, Oprema: ABS, Meusburger MPG-3 Nizkopodnožno prikolica s ponjavo, krmiljena/dvigljiva os Oprema: zračno vzmetenje * Tehtnica za os * 1. os dvigljiva * 3. os krmiljena * Hidravlična rampa z dodatno podporo in daljinskim upravljanjem * Prehodna rampa * Električni vitel z daljinskim upravljanjem Ppsdpewfwd Dsfx Agfsp * Edscha streha * Stranski zaboji za shranjevanje * Rezervno kolo s standardno pnevmatiko * Dodatni žarometi * Izvlečne table za izredne širine Varnost: ABS * EBS * Kolutne zavore Pridržujemo si pravico do napak in predhodne prodaje. Interna številka vozila: 8303

Stanje: rabljeno, prevoženi kilometri: 939.311 km, moč: 331 kW (450,03 KM), prva registracija: 04/2021, vrsta goriva: dizel, zavore: retarder, barva: bela, vrsta prenosa: samodejen, emisijski razred: Euro 6, Leto izdelave: 2021, MERCEDES-BENZ ACTROS 1845 4x2 Trekkerunits Blad-/Luchtvering, Mirrorcam, Retarder Type: Trekkerunit Bouwjaar: 2021 Kilometerstand: 939.311 km BTW-id: BTW-plichtig voertuig, vermelde prijs is excl. BTW. Specificaties: - 6-cilinder lijnmotor met turbo, 450 pk - Euro 6 - Hydraulische retarder - Mirrorcam - Nieuw dashboard - Zware as, naafreductie - Voor bladvering, achter luchtvering - Koelkast - Airconditioning De truck is in topconditie en direct inzetbaar. Zeer krachtige truck. Wereldwijde verzending kunnen wij voor u regelen. Bekijk ons volledige aanbod op onze website. Overige informatie: - Laadvermogen: 44.000 kg - Transmissie | Aantal versnellingen: 12 - Transmissietype: Mercedes - Toelaatbaar gewicht: 44.000 kg Overige uitrusting: - Intarder - Retarder Tony Trucks B.V. | Meer foto’s op aanvraag Contact | Michel Kurt | Tel: | WhatsApp: | Email: Tony | Tel: | WhatsApp: Ppodpfx Ageyawm Tsfop Exportkosten: Neem vooraf contact op over tarieven en procedures die in uw land gelden Locatie: Bergschenhoek (NL) | 130 km van de grens | 10 km van Rotterdam The Hague Airport Disclaimer: Wijzigingen, tussentijdse verkoop en fouten voorbehouden. Vermelde prijzen zijn exclusief BPM en gelden alleen voor export.