Dinkel 4-Achs-Jumbotieflader - Doppelte Rampen nakup rabljenega (39.505)

Stanje: novo, največja dovoljena obremenitev: 45.250 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.550 mm, Oprema: ABS, Our entire range of vehicles, including immediately and short-term available units, can be found on our website. Excerpt from the equipment list. Full equipment details available upon request. Chassis, cranked: * Special steel frame made of high-strength fine-grain steels, electrically welded at connection points * Well-dimensioned outer frame, 4-axle configuration * Wheel coverings above the axles with spray mist suppression * All steel parts shot-blasted * Side underride guard made of anodised aluminium, installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special configuration in the cranked area for maximum low bed length, combined with AluLeg drop-down supports instead of telescopic support winches, maximum rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special body construction * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions can be extended for loading and unloading to approx. 4,200 mm * Three sliding stanchions per side with spring-assisted lifting * Additional central stanchion locks in the roof rail and parked position by pull cable and spring bolt * DINKEL mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable on both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments, with adjustment in the stanchions * Front cover at the bulkhead for driving under tarp, total height up to approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the side, lower 450 mm pockets, above that 4 rows of individual pockets. In the raised bed, only 3 rows of plug-in slats, with uniform spacing Floor: * Approx. 27 mm special waterproof bonded beech plywood, slip-resistant surface * Steel sheet in wheel arch areas, forklift-rated to DIN standard * Outer frame with flush surface Brakes: * WABCO air brake system with EBS according to EC regulation 71/320 EEC incl. PREV (parking-release safety valve) * Spring-loaded brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-bed configuration * Air suspension with lifting and lowering system, total travel approx. 230 mm * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: Gbedpowx Dbiofx Acgjl * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * without spare wheel Lighting: * As per EC regulation, incl. LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights in the front wall, inside, at the top Paintwork: * Chassis and body in single colour RAL 3002 Carmine Red * Central stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signage at front and rear in galvanized, continuously telescopic version with mounted contour lights including plug bases for beacon lights (small panels) * Additional external unlocking for sliding roof frame * 4 stanchion adapters for special outer frame profile, to lock central stanchions as required * PVC sliding tarpaulins, colour similar

Stanje: rabljeno, največja dovoljena obremenitev: 44.980 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, naslednji pregled (TÜV): 09/2025, skupna širina: 2.550 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt of the equipment list. Complete equipment details available upon request. Chassis, cranked * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, robust outer frame * 4-axle configuration. Wheel arch covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection mounted, made of anodised aluminum * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special design in the cranked area for maximum low-bed length in combination with AluLeg drop supports instead of telescopic landing gears, maximum rear swing radius of the tractor unit approx. 2,100 mm Gbedpfx Acelthguogol Special superstructure with rear stake extension * Self-supporting aluminium roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable to approx. 4,200 mm * Three sliding stakes per side with spring-assisted tension relief * Additional central stake locks in the roof beam and parking position, operated via pull cord and spring latch * Mechanically height-adjustable roof lift, adjustment height approx. 400 mm, can be operated from either side or single side without needing to open the opposite side and doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with stake height adjustment * Front overlap at bulkhead for driving under tarpaulin up to an overall height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on each side, 450 mm pockets below, above 4 rows of single pockets * In the high bed, only 3 rows of slats. Intermediate distances evenly distributed Floor * approx. 27 mm special water-resistant bonded beech plywood, non-slip surface * Steel plate in wheel arch area * Forklift accessible per DIN ? standard * Outer frame surface flush Brakes * WABCO air brake system with EBS complying with EC Directive 71/320 EEC incl. PREV (park-release safety valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer with drum brakes, low loader specification * Air suspension with raise/lower function, total lift approx. 230 mm * Third and fourth axles are friction-steered trailing axles with electrical and mechanical locking Twin tires * 235/75 R 17.5, -16, incl. spare wheel holder. Without spare wheel Paintwork * Chassis in RAL 3002 red, solid color * Central stakes and axles KTL coated black * Corner posts galvanized finish * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork solid color per RAL shade Included special equipment * Air suspension with ECAS control, operated at the trailer * Oversize signage front and rear, galvanized, infinitely extendable, with marker lights incl. plug-in sockets for revolving beacons (small panels) * Additional unlocking for sliding roof frame from outside * 4 stake adapters for special outer frame profile, for flexible locking of central stakes * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, oversize/height version, flat hooks, tarpaulin folds, closures with safety pawl / OCS * Left rear telescopic plug-in socket for revolving beacon incl. beacon * Outer frame for machine transport with approx. 64 securing points in 2,000 kg, 3,000 kg and 10,000 kg versions, according to construction release drawing * 1

Stanje: novo, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, Zračno vzmetenje z možnostjo dviga in spusta, Tehtnice za obremenitev osi, Skupna dolžina nakladalne površine pribl.: 9.100 mm, Globoka postelja pribl.: 6.900 mm dolga, Višina nakladanja pod obremenitvijo pribl. 890 mm, 24 x pritrdilna ušesa po 10 t, 12 x žepov za kolike v zunanjem okviru, Plezalna letvica na zunanji strani ramp in zadnje poševnine, Dvodelne nakladalne rampe (pribl. 4.300 x 750 mm), Nakladalne rampe nastavljive vstran, Lesena tla debeline 68 mm, Skladiščna škatla s pokrovom za verige ali pritrdilne pasove, Označevanje obrisa po predpisih, Opozorilna rotacijska luč, Pomožna parkirna zavora z vzmetjo, Vklj. prikaz obremenitve osi, Vozilo pocinkano v potopni kopeli, Doplačilo za: Hidravlični premik ramp = cena: 1.000 €, -- Možne tiskarske napake, spremembe in napake so pridržane, vzorčne slike --, Več podatkov na: !, Več podrobnosti na: ! Gsdpfxey Rlmde Acgobl

Stanje: novo, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.350 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Flatbed, ABS, air suspension with lift/lower function, axle load scales, total platform length approx. 9,350 mm, 32 lashing rings, 10 stake pockets in the outer frame, loading ramps (approx. 3,100 x 760 mm), cleat strip on outside of ramps and rear slope, ramps adjustable sideways, 68 mm thick wooden floor, storage box with lid for lashing chains or tie-down straps, mandatory contour marking, rotating beacon, spring-loaded parking brake, incl. axle load indicators, chassis fully hot-dip galvanized, Surcharge for: hydraulic ramp adjustment, Price: €1,000. -- Subject to typing errors, mistakes, and changes. Sample images. For more data see: !, More Details: ! Gjdey Niu Njpfx Acgebl

Stanje: novo, lastna masa: 9.150 kg, največja dovoljena obremenitev: 30.850 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, zračno vzmetenje z dvigovanjem in spuščanjem, tehtnice za obremenitev osi, skupna dolžina tovorne površine ca: 9.100 mm, nizko ležišče ca: 6.900 mm dolgo, nakladalna višina obtežena ca. 890 mm, 24 x pritrdilnih ušes po 10 t, 12 x žepov za stebričke v zunanjem okvirju, nakladalne rampe (ca. 3.100 x 760 mm), stopničasta letev na zunanji strani ramp in zadnjega naklona, rampe bočno nastavljive, lesena tla debeline 68 mm, skladiščna škatla z pokrovom za pritrdilne verige ali pasove, označba obrisa po predpisih, rotacijska opozorilna luč, zavorni sistem s federnim pomnilnikom, vklj. z indikatorji obremenitev osi, vozilo vroče pocinkano v potopni kopeli, doplačilo za: hidravlično pomikanje ramp = cena: 1.000 €, -- napake v tisku, pomote in spremembe pridržane, slike so simbolične --, Več podatkov na: !, More Details: ! Godpfx Ajy Izrqjcgjbl

Stanje: novo, lastna masa: 9.550 kg, največja dovoljena obremenitev: 30.450 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Air suspension with lift and lower function, axle load scales, total loading platform length approx. 9,100 mm, low bed approx. 6,900 mm long, loaded loading height approx. 890 mm, 24 lashing rings each rated at 10 t, 12 stake pockets in the outer frame, drive-on ramps (approx. 3,100 x 760 mm), climbing strip on the outside of the ramps and rear slope, ramps adjustable sideways, 68 mm thick wooden floor, storage box with lid for lashing chains or tension belts, contour marking according to regulations, revolving beacon, spring-applied parking brake, incl. axle load displays, vehicle hot-dip galvanized, surcharge for: hydraulic ramp shifting = Price: €1,000, -- Subject to errors, misprints and changes, sample images --, More data at: !, More details: ! Gedpfx Asy Irxnocgebl

Stanje: novo, lastna masa: 9.150 kg, največja dovoljena obremenitev: 30.850 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, zračno vzmetenje z dvigom in spustom, tehtnice za obremenitev osi, skupna dolžina nakladalne površine cca: 9.100 mm, globoko ležišče cca: 6.900 mm dolgo, nakladalna višina obremenjena cca 890 mm, 24 x pritrdilnih ušes po 10 t, 12 x žepov za stebričke v zunanjem okviru, plezalna letev na zunanji strani ramp in zadnjega naklona, nakladalne rampe (pribl. 3.100 x 760 mm), rampe bočno nastavljive, lesena tla debeline 68 mm, zaboji z pokrovom za pritrdilne verige ali napenjalne trakove, konturirana označitev po predpisih, opozorilna luč, parkirna zavora s shranjevalnim vzmetjo, vključuje prikazovalnike obremenitve osi, vozilo vroče pocinkano s potopno kopeljo, doplačilo za: hidravlični premik ramp = cena: 1.000 €, -- Možne tiskarske napake, spremembe in napake pridržane, slike so simbolične --, Več podatkov na: !, Več podrobnosti na: ! Gbsdpfxoy Ifite Acgel

Stanje: novo, lastna masa: 9.150 kg, največja dovoljena obremenitev: 30.850 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, zračno vzmetenje z dvigovanjem in spuščanjem, tehtnice za obremenitev osi, skupna dolžina tovorne površine ca: 9.100 mm, nizko ležišče ca: 6.900 mm dolgo, nakladalna višina obtežena ca. 890 mm, 24 x pritrdilnih ušes po 10 t, 12 x žepov za stebričke v zunanjem okvirju, nakladalne rampe (ca. 3.100 x 760 mm), stopničasta letev na zunanji strani ramp in zadnjega naklona, rampe bočno nastavljive, lesena tla debeline 68 mm, skladiščna škatla z pokrovom za pritrdilne verige ali pasove, označba obrisa po predpisih, rotacijska opozorilna luč, zavorni sistem s federnim pomnilnikom, vklj. z indikatorji obremenitev osi, vozilo vroče pocinkano v potopni kopeli, doplačilo za: hidravlično pomikanje ramp = cena: 1.000 €, -- napake v tisku, pomote in spremembe pridržane, slike so simbolične --, Več podatkov na: !, More Details: ! Gbedpfx Acsy Ifg Esgel

Stanje: novo, lastna masa: 9.150 kg, največja dovoljena obremenitev: 30.850 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, zračno vzmetenje z dvigom in spustom, tehtnice za obremenitev osi, skupna dolžina nakladalne površine pribl. 9.100 mm, nizka postelja pribl. 6.900 mm dolžine, nakladalna višina pod obremenitvijo pribl. 890 mm, 24 x pritrdilna ušesa po 10 t, 12 x žepov za stebričke v zunanjem okviru, nakladalne rampe (pribl. 3.100 x 760 mm), protidrsna letev na zunanji strani ramp in zadnjem nagibu, rampe bočno nastavljive, lesen pod 68 mm debeline, škatla z pokrovom za verige ali privezne pasove, obrisna označitev po predpisih, rotacijska luč, parkirna zavora s tlačno vzmetjo, vklj. z indikatorji obremenitve osi, vozilo vroče cinkano s potapljanjem, doplačilo za: hidravlično premikanje ramp = cena: 1.000 €, -- Pridržujemo si pravico do napak v tisku, sprememb in zamenjav, primer slike --, Več podatkov na: !, Več informacij na: ! Gbedoy H A Scspfx Acgsl

Stanje: novo, lastna masa: 9.150 kg, največja dovoljena obremenitev: 30.850 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.100 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, ABS, zračno vzmetenje z dvigom in spustom, tehtnice za obremenitev osi, skupna dolžina nakladalne površine pribl. 9.100 mm, nizka postelja pribl. 6.900 mm dolžine, nakladalna višina pod obremenitvijo pribl. 890 mm, 24 x pritrdilna ušesa po 10 t, 12 x žepov za stebričke v zunanjem okviru, nakladalne rampe (pribl. 3.100 x 760 mm), protidrsna letev na zunanji strani ramp in zadnjem nagibu, rampe bočno nastavljive, lesen pod 68 mm debeline, škatla z pokrovom za verige ali privezne pasove, obrisna označitev po predpisih, rotacijska luč, parkirna zavora s tlačno vzmetjo, vklj. z indikatorji obremenitve osi, vozilo vroče cinkano s potapljanjem, doplačilo za: hidravlično premikanje ramp = cena: 1.000 €, -- Pridržujemo si pravico do napak v tisku, sprememb in zamenjav, primer slike --, Več podatkov na: !, Več informacij na: ! Gedpfx Acey H A Nuegobl

Stanje: novo, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.350 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Flatbed, ABS, air suspension with lift/lower function, axle load scales, total platform length approx. 9,350 mm, 32 lashing rings, 10 stake pockets in the outer frame, loading ramps (approx. 3,100 x 760 mm), cleat strip on outside of ramps and rear slope, ramps adjustable sideways, 68 mm thick wooden floor, storage box with lid for lashing chains or tie-down straps, mandatory contour marking, rotating beacon, spring-loaded parking brake, incl. axle load indicators, chassis fully hot-dip galvanized, Surcharge for: hydraulic ramp adjustment, Price: €1,000. -- Subject to typing errors, mistakes, and changes. Sample images. For more data see: !, More Details: ! Godpjy Hfv Refx Acgobl

Stanje: novo, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.350 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Flatbed, ABS, air suspension with raising and lowering function, axle load scales, total loading area length approx. 9,350 mm, 32 lashing rings, 10 stake pockets in the outer frame, loading ramps (approx. 3,100 x 760 mm), climbing strips on the outside of ramps and rear slope, laterally adjustable ramps, 68 mm thick wooden floor, storage box with lid for lashing chains or tension belts, contour marking according to regulations, rotating beacon, spring-applied parking brake, incl. axle load indicators, vehicle hot-dip galvanized, surcharge for: hydraulic ramp adjustment = price: €1,000, -- Errors, omissions, and changes excepted, sample pictures --, More data at: !, More details: ! Gbodpfxeyy Nams Acgol

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, lastna masa: 15.900 kg, največja dovoljena obremenitev: 42.100 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 11/2001, dolžina tovornega prostora: 8.960 mm, širina tovornega prostora: 2.520 mm, skupna dolžina: 12.950 mm, skupna širina: 2.520 mm, skupna višina: 3.800 mm, vzmetenje: hidravlika, velikost pnevmatike: 245/70R17,5, medosna razdalja: 1.360 mm, največja hitrost: 90 km/h, barva: modra, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2001, Oprema: ABS, Nooteboom MCO-73-04V Top trailer from first owner, first registration 21.11.2001, Fully overhauled in 2014, Brakes renewed in 12.2025! 66,000kg total combination weight with 3-axle tractor unit, Gross weight 58,000kg, Fifth wheel load 18,000kg, 1-4 axles: 10,000 / 10,000 / 10,000 / 10,000kg, Unladen weight 15,900kg, Please refer to the technical data sheet for exact dimensions, Lowbed: 8.96m + 5.50m telescopic extension, Hydraulic supports front and rear allow the trailer including up to 30t of payload to be lifted completely—ideal for unloading laterally at a ramp, Hydraulic suspension (enables leveling even with uneven load distribution), First axle liftable, All four axles are steerable, either automatically or via remote control (also in opposite direction), Hydraulic ramps and hydraulically extendable up to 3,000mm, Load platform extendable to 3,000mm, Tyres 245/70R17.5 – 1st axle: 6/6/6/6mm, 2nd: 11/11/8/8mm, 3rd: 9/9/7/7mm, 4th: 11/11/7/5mm, Spare: 6mm, More details upon request. Sale only to business customers or for export. Leasing/financing available upon request – immediate processing possible, also without down payment! Further details and requirements on request. Vehicle description is for general identification purposes. All information, images and descriptions are non-binding. Equipment must be verified separately if necessary. The seller accepts no liability for typing or data transmission errors. Errors and prior sale reserved. Thank you very much for your interest! We look forward to your visit. Our SERVICE We are happy to take your used vehicle in part-exchange, 30-day export license plate incl. insurance, EUR-1 and all customs documents for export, TÜV / SP / UVV / tachograph inspection / OBU installation, Professional transportation to your location, Transfer from Stuttgart Airport / Sindelfingen station to us by arrangement, Retrofitting with additional components and other individual customer requests possible upon request. Gbsdpfeyqm I Uex Acgjl

Stanje: rabljeno, lastna masa: 14.350 kg, največja dovoljena obremenitev: 48.650 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Leto izdelave: 2025, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - SNT design gooseneck for optimized loading platform length, length approx. 3,700 mm - Gooseneck rear with approx. 1,000 mm x 10° bevel Loading Platform: - Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° - Recessed area in platform and bevel for accommodating the excavator’s dipper stick Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide - Ramps with hardwood decking - Hydraulically folding ramp tips - Ramps hydraulically adjustable individually, approx. 235 mm outward and 215 mm inward - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the ramp outer frame Axles and Suspension: - BPW axles and suspension, first axle steering assist, all other axles forced steered hydromechanical - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse-lock, activated via reverse gear or manually - Air suspension with lift/lower valve - 235/75 R 17.5 tires - TPMS tire monitoring system Included Accessories: - Detachable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic controls (except hydraulic winches) - Park position for warning signs on gooseneck when not in use - 1 spare wheel - Gooseneck outer beams with fixing holes for bolted lashing rings - First borehole approx. 200 mm from the front, then every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of recessed lashing rings at the rear of the gooseneck - Gooseneck with 1 pair of plug-in anodized ALU sideboards, approx. 400 mm high - Gooseneck with plug-in anodized ALU rear board, approx. 400 mm high - Gooseneck deck with 40 mm thick hardwood, with checker plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - Round NATO socket on the front connector strip - 4 wheel chocks - Mechanical landing legs with 2-speed gearbox and crank - Loading platform with continuous and between-axle interrupted approx. 50 mm thick hardwood deck - Platform locking with conically welded locking profiles every 250 mm - Including pre-tensioning plate Gbedeyrfn Nopfx Acgsl - 1 intermediate table, approx. 300 mm wide, for extension tube with large cross-section; intermediate table has offset loading surface and extendable hanging rails for aluminum bridging elements - 1 pair of lashing rings on the front cross member - 8 pairs of recessed lashing rings in outer frame of platform, can be folded outwards - Galvanized extensions extendable by approx. 230 mm per side - Wheel wells with square climbing bars, 15 x 15 mm, open continuously in front of the axles to the gooseneck cross member, approx. 700 x 410 mm - ALU covers for wheel wells, also usable as bridging elements for extension or as widening planks - Aluminum elements lockable onto extension tubes of the widenings - Extendable U-profiles for ALU covers - Wheel wells with square climbing bars, 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - 1st axle with automatic lift axle function - 4 warning signs, approx. 423 x 423 mm - Radio and cable remote control

Stanje: rabljeno, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2024, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, Leto izdelave: 2024, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functional report. Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long - Gooseneck rear with chamfer, approx. 1,000 mm x 10° Loading platform: - Extendable loading platform, approx. 8,800 mm long, with chamfer at the rear approx. 500 mm x 10° - A recess in the loading platform and into the chamfer to accommodate the excavator's dipper stick - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood surface on the chamfer of the loading platform Ramps: - 1 pair of two-part steel ramps, approx. 4,350 mm long and 900 mm wide - Ramps with hardwood inlay - Hydraulically foldable ramp tips - Ramps can be hydraulically shifted approx. 235 mm outwards and 215 mm inwards individually - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle with forced steering, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - Air suspension - Tyres 235/75 R 17.5 - TPMS tyre monitoring system - TPMS tyre pressure sensors Gbodpsypb Akefx Acgol Included Accessories: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for hydraulic operations - 1 spare wheel - Outer beams on the gooseneck with fixing holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear of the gooseneck - On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized - 2" kingpin - Round NATO socket at the front connection bar - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outwards - Extendable galvanized outriggers, approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm, open continuously in front of the axles up to the gooseneck crossmember, approx. 700 x 410 mm - ALU covers for the wheel recesses - Lockable aluminium elements fitted on the extension pipes of the outriggers - Widenable U-profiles for inserting the ALU covers - Wheel recesses with square climbing strips, 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - Lockable aluminium elements fitted on the extension pipes of the outriggers - 1 pair of mechanical rear supports - Remote steering control from both front and rear by cable remote control, with axle single-track alignment control - 1st axle with automatic lift axle function and start assist according to EU Directive 2021/535 - Under the gooseneck and at the rear crossmember left and right: 7-pin sockets with mountings for warning plates - Square climbing strips 20 x 30 mm, spaced approx. every 200 mm on the chamfered part of the loading platform outer frame - Central lubrication system with 1 pump, BEKAMAX - Radio remote control for steering in addition to cable remote - Wabco Smart Board system - 4 warning plates, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Gbjdpfx Acsk Aht Uegsl Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Gbedpfx Acsk Ahugsgel Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Gbjdpol Uxdkofx Acgsl Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a

Stanje: novo, največja dovoljena obremenitev: 49.000 kg, skupna masa: 60.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Extendable Loading Platform: - Loading platform, extendable design with rear chamfer of approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, checker-plate covering above the axles Godpoh Etf Rofx Acgebl Two-Part Removable Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulic side-shift - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles, two fixed axles and two steering axles (self-steering), air suspended, with drum brakes, raise/lower function - Self-steering axles with electro-magnetic reverse lock, can be activated by reverse gear or manually - Axle tool kit - Tyre size 235/75 R 17.5 Brake System: - Braking system according to EU regulations with EBS-E (4S3M) Steel Structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class, long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality single-tone topcoat using 2-component (2K) paint in Nova grey Electrical System: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with 24N, 24S, and 15-pin sockets Included Accessories: - 2" kingpin - Galvanized steel front wall, approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings on the galvanized front connector strip - 4 wheel chocks with holders on the front wall - Mount at the rear section of the gooseneck for ALU approach ramps - Galvanized folding supports underneath the loading platform chamfer - One holder for warning beacon - Cover plates to bridge the gap between ramps and loading platform - White reflective tape on the side, red on extension and rear, according to EU regulations - Electro-hydraulic power unit - At the gooseneck and ramps (left/right) a holder each for warning signs including socket - Control valves for the ramps mounted on the right side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the gooseneck, plug-in ALU side boards and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, two 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform - Galvanized, extendable platform wideners approx. 230 mm per side - Lift axle on the front axle with control system - 20 x 20 mm square climbing bars - BEKAMAX central lubrication system - Four warning signs extendable by approx. 400 mm eac

Stanje: rabljeno, največja dovoljena obremenitev: 31.050 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2016, naslednji pregled (TÜV): 06/2026, dolžina tovornega prostora: 9.500 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, skupna višina: 3.650 mm, Oprema: ABS, * Schwarzmüller 4-osni nizkopodni priklopnik z dvojnimi hidravličnimi zložljivimi rampami - visoko priklopljen s 50 mm obročem * Zračno vzmetenje - BPW osi - kolutne zavore - pnevmatike: 245/70R17,5 * Skupna dolžina: 11.900 mm - širina: 2.500 mm (možno do 3.000 mm) - višina: 3.650 mm Gbedpfey Dy Enox Acgel * Dovoljena skupna masa: 40.000 kg - lastna masa: 8.950 kg - nosilnost: 31.050 kg * Nemško vozilo - nemški prometni list - takoj na voljo - iz prve roke * Leva zadnja hidravlična podporna noga potrebuje popravilo * Za ogled prosimo, da se dogovorite za termin * Kontaktna oseba: gospod Andreas Vogel * Podatki na internetu so nezavezujoči opisi. * Ne predstavljajo zagotovljenih lastnosti. * Prodajalec ne odgovarja za tipkarske ali prenosne napake podatkov. * Pridržujemo si pravico do sprememb, napak in predhodne prodaje.

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck Gjdpfei Ai E Rex Acgebl - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: novo, največja dovoljena obremenitev: 30.540 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.550 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 2.990 mm, skupna širina: 2.550 mm, skupna višina: 1.010 mm, Leto izdelave: 2025, Oprema: ABS, SCHWARZMÜLLER 3-Axle Flatbed Semi-Trailer RH100 – Extendable – For building materials and construction machinery transport NEW VEHICLE Gross weight (technical): 39 t Axle load (technical): 27 t Fifth wheel load (technical): 12 t Empty weight approx. 9 t (+/- DIN tolerance) Flatbed length approx. 13,500 mm = front approx. 4,150 mm, rear approx. 9,350 mm Flatbed width approx. 2,540 mm Loading height front approx. 1,060 mm at coupling height approx. 980 mm, rear 1,010 mm Extendable lightweight steel welded frame construction Extension length approx. 4,000 mm, lockable at intervals of approx. 500 mm Reinforced version for building material transport, 20 t/5m at centre of gravity; construction machine transport up to 20 t (in retracted position) Reinforced U-profile outer frame 6 mm Tapered cross-members 4 mm Bevelled frame at rear, approx. 15°, approx. 500 mm Visual indicator for pneumatic frame locking on both sides, with green control lamp = indicator light for pneumatic frame locking at front left of the fifth wheel Energy guiding chain in central frame Frame locking with integrated lubrication strip 4 pairs of extendable 8 t lashing rings, rear 9 pairs of extendable 10 t lashing rings in outer frame profile, foldable outward on both sides for oversize cargo lashing 10 pairs of lashing mushrooms with welded round steel at lower edge of outer frame 6 pairs of insert sleeves with reinforcement bar for square tube side stanchions 80x50x5 mm (longitudinal, approx. 3 mm clearance), on both sides of outer frame 3 insert sleeve cross-members for side stanchions 80x80 mm, located at central cross-members Insert sleeve cross-members as empty holders for stanchions 6 pairs of sunken container locks for: 2 x 20 ft containers 1 x 20 ft container central 2 x 20 ft containers 1 x 30 ft container Reinforced rear end plate with continuous ramp hanger rail Mechanical 2 x 12 t landing legs, single-sided operation + compensation 2 drop support legs at rear SAF Intradisc B9 axles with 370 mm disc brakes (19.5" discs), Load capacity 9 t/axle, on-road specification Axle spacing 1,310 + 1,410 mm Wheelbase 7,650 mm SAF steering trailing axle with kingpin/bushing approx. 10° steering angle, automatic electro-pneumatic reverse lock, engages automatically in reverse, additional cab switch with release valve Special axle lift on 1st axle, automatic raise/lower depending on weight, with forced lowering, start assist via cab button / "3 x brake" Kilometre counter 6x tyres 435/50 R 19.5, 164J Godjwfu N Ropfx Acgobl 6x steel rims 14.00 x 19.5 Brake system according to EC Directive 71/320 ECE R13 2-line air brake system, EBS system 2S2M, one axle with sensors RSS/RSP stability programme Spring-loaded parking brake Steel air tanks Air suspension with lifting and lowering device, total stroke approx. 200 mm Automatic ride height 15 km/h Quick release valves SWIT – Schwarzmüller Intelligent Telematics, package "BASIC" Axle load display via EBS CAN bus signal Tyre pressure monitoring according to ECE Regulation 141 35 mm wooden floor, longitudinal over wheels with steel checker plate cover Wooden floor impregnated both sides Reinforced steel front wall approx. 1,800 mm + centre supports integrated into front wall 2 lashing eyes top of corner posts Front steel corner posts integrated into front wall, front (clear side loading length) 24-volt lighting system according to EC Directive 76/756/EWG 2 units full-LED multifunction tail lights "Aspöck" with integrated control unit Flashing LED side marker

Stanje: rabljeno, največja dovoljena obremenitev: 30.700 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2002, Oprema: ABS, * MüllerMitteltal nizkopodni priklopnik s 4 osmi T40 * 2x krmiljeni vrtljivi osi * Nemška prikolica * pero * hidravlično pomične rampe / levo-desno * deljene preklopne rampe * možnost razširitve * ABS Gedpfjyuri Ejx Acgsbl * BPW osi * 40 t * lastna teža: 9300 kg * osne obremenitve = 10 t na os * popolnoma funkcionalen * pnevmatike v redu

Stanje: rabljeno, največja dovoljena obremenitev: 31.710 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2016, skupna širina: 2.550 mm, Oprema: ABS, Our complete vehicle inventory with immediately and short-term available vehicles can be found on our website. Excerpt from the equipment list. Full equipment details available on request. - Chassis wedge-shaped, increased point load approx. 25,000 kg over approx. 5,000 mm - 24,000 kg telescopic support winches with load and rapid operation - Lashing points available in 5,000 kg, 6,000 kg, and 10,000 kg variants - 8 stake pocket inserts (for second bulkhead) - Aluminum roof bow with sliding tarpaulin - Rear stakes extendable up to approx. 3,500 mm, for loading and unloading only - Three sliding stakes per side - End stakes longitudinally extensible in direction of travel - Bulkhead fully designed as storage compartment with integrated shelving system, closed on the inside - DINKEL mechanical hydraulic lifting roof, height-adjustable. Lifting roof height: 400 mm, operable from both sides or one side - Additional height adjustment of 480 mm in 40 mm increments (12 x 40 mm), height-adjustable within the stake pockets - Trailer moveable under tarpaulin up to a total height of approx. 4,400 mm (rear side open above tail lift) - Upper portal cross member with movable sliding tarpaulin - Four rows of stackable 150 mm aluminum slats on each side (in raised bed, only 2 rows), lower: 450 pockets, above: 4 rows of pockets, evenly spaced - WABCO air brake system with EBS, EC-regulation 71/320 EEC incl. PREV - Air suspension in ECAS version, with raise and lower function - Wabco Smart Board with axle load indicator and hubodometer - 3 x 10,000 kg SAF axles with drum brakes - 3rd axle as friction-steered trailing axle Gbjdpfxoy Dy Ehs Acgsl - 1st axle liftable - Tires: 235/75 R 17.5 - Dhollandia heavy-duty tail lift type DHLSU, lifting capacity 9,000 kg – load distance 1,000 mm, steel platform approx. 3,000 x 2,500 mm - Hydraulic additional support, automatic ground leveling - Tail lift with ramp function for platform tilting, can be used as a drive-on ramp – loadable up to max. 13,500 kg - Chassis painted in MB-Novagrau - Superstructure with white tarpaulin featuring customer branding

Stanje: rabljeno, lastna masa: 10.660 kg, največja dovoljena obremenitev: 37.340 kg, skupna masa: 48.000 kg, prva registracija: 03/1992, vzmetenje: drugo, velikost pnevmatike: 215/75 R17.5 141/140 J, največja hitrost: 80 km/h, barva: rdeča, vrsta prenosa: drugo, velikost sprednje pnevmatike: 215/75 R17.5 141/140 J, velikost zadnje pnevmatike: 215/75 R17.5 141/140 J, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, centralno zaklepanje, sistem za imobilizacijo, Kontaktna oseba prodaje: Frank Rau / Rusko / Angleško / Nemško - Bachar Ibrahim / Arabsko / Angleško / Nemško - Gbedpexqav Djfx Acgol Registracijske storitve, HU/SP/UVV, prevoz do pristanišča. Osnovna barva: rdeča Dodatna oprema ABS, vozilo pripravljeno na vožnjo, zračno vzmetenje, cena na zahtevo (Mobile), video, imobilizator, centralno zaklepanje, nosilnost (kg): 37340 Tip nadgradnje: Nooteboom OSD-48-03 V/L nizkopodni polpriklopnik. Razširitve 3000 mm, izvlečne površine, HSN/TSN: Pridržujemo si pravico do napak.