Fliegl Samooskrba 3 Strani nakup rabljenega (342)

Stanje: novo, številka stroja/vozila: 637ca014c140e4e48dc3231a0, lastna masa: 5.700 kg, največja dovoljena obremenitev: 33.300 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.700 mm, širina tovornega prostora: 2.350 mm, višina nakladalnega prostora: 1.600 mm, prostornina tovornega prostora: 31 m³, skupna dolžina: 9.090 mm, skupna širina: 2.550 mm, skupna višina: 3.110 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, Further Information Chassis Semi-Trailer Tipper Fine-grain steel welded construction in Basic lightweight design, with saddle plate and replaceable 2" kingpin Curved front panel (patented) 24 t 2-speed landing gear, single-sided operation, with straight lower section, without stroke compensation Wheel chocks with bracket Foldable underrun protection Half-shell mudguards Integrated mudguard bracket, stone-repellent surface With antispray mudflap only on last axle Tarpaulin bar with holder Tow hook at rear Axles & Suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year corrosion warranty Brake System 2-line compressed-air braking system, color-coded line routing for easy servicing Spring-loaded parking brake 2 interchange-proof coupling heads at front, without connecting line EBS, electronic braking system with EBS socket at front, without connection cable Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With raise & lower valve Vehicle Stability System Wheels and Tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire Pressure Monitoring System, compliant with ECE R 141, displayed on tractor display via EBS, without truck installation (functionality must be available in the truck; applies only to basic tires) Electrics 24 Volt, multi-chamber lights, lateral yellow LED lights Lateral yellow LED lights, synchronized with blinker "flashing side marker lights" 2 x 7-pin, interchange-proof sockets at front, without connection cable Hydraulics Low pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Hydraulic operation via truck PTO Body Steel round dump body in "Stone Master Design" made of highly wear-resistant HB 400/450 steel. Slanted front wall with external hydraulic cylinder mount. Access step inside on front wall. Greenline – conical and aerodynamic body shape Shovel and broom holder outside on front wall. Membrane rear wall Rear wall as pendulum tailgate with double joint hinge, external with double hook locking. Two clamping screws with wing closures at the lower sides. Continuous side walls, 4 mm thick; floor 4/5 mm thick, wear- and weight-optimized construction Standing platform with access ladder, connection plate for air/electrics and brake, with generous clearance for best possible operation Roll tarp can be placed one-sided on R-rear, with central locking on L-rear Registration country / plates Germany Type approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE-70 Contour marking with reflective tape according to ECE R 048, white on sides and red at rear Paintwork Frame: DB 7350 Nova Grey "10-year anti-corrosion warranty" Landing legs: powder-coated black Body: RAL color of choice, single-color Dcedpfx Aoi Rivdoiaoh Roll tarp: RAL 7035 light grey

Stanje: novo, številka stroja/vozila: 8b1f4087611d72661dc0b3869, lastna masa: 4.750 kg, največja dovoljena obremenitev: 30.250 kg, skupna masa: 35.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.200 mm, višina nakladalnega prostora: 1.450 mm, prostornina tovornega prostora: 25 m³, skupna dolžina: 8.600 mm, skupna širina: 2.550 mm, skupna višina: 3.000 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22.5, Further Information Chassis, Semi-trailer Tipper Fine-grained steel welded construction, in basic lightweight design, kingpin plate with replaceable 2" kingpin Patented curved front end 24 t, 2-speed landing gear, single-sided operation, with straight base, without compensating ram Foldable underrun protection Half-shell mudguards Tow hook at rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Laser-measured axles/chassis: reduces tyre wear and fuel consumption Axles in off-road specification Air suspension 1st axle is an automatic lift axle, incl. forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year anti-corrosion warranty Braking System 2-line compressed air braking system with color-coded line routing for easy servicing Spring-loaded parking brake 2 foolproof coupling heads at front, without connection line EBS electronic braking system with EBS socket at front, no connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of ABS! Raise & lower valve included Vehicle stability control system Wheels and Tyres 385/65 R22.5 Steel rims, OEM silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via towing vehicle dashboard over EBS, no truck installation (requirement: system compatibility in the truck; only for base tires) Electrics 24 Volt, multifunctional lights, yellow side LED marking lights Yellow side LED marking lights linked to indicator (“flashing side lights”) 2 white front position lights 2 white/red rear edge marker lights 2 x 7-pin foolproof sockets at front, no connection cable Hydraulics Low-pressure cylinder max. 170 bar, lowest stage hard-chrome plated, with HDK screw coupling, fixed section, nominal width 48 mm (without hose connection) Operated hydraulically via truck PTO Body Steel round body in “Stone Master” design, made from highly wear-resistant HB 400/450 steel. Sloped front wall with external hydraulic unit and access ladder at front wall. Greenline – conical and aerodynamic body shape External shovel and broom holders on front wall Membrane rear wall Rear wall as pendulum tailgate with double-joint hinge, exterior mounting with dual hook locking. 2 clamping screws with toggle locks on lower sides. Continuous side walls 4 mm thick, floor 4/5 mm thick, wear- and weight-optimized construction Standing platform with access ladder, connection plate for air/electric/bra ke system with generous clearance for optimal operability Roll tarp can be stowed right-hand side, with central locking on left-hand side Country of Registration / License Plates Germany Dodpoi Ri Nfefx Aiaoch With Dekra inspection and report (according to §13 EC - FGV) Body strength according to EN 12642 24/7 Service Hotline Prepared for single-line license plate holder Contour marking with reflective tape ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Nova Grey 10-year anti-corrosion warranty Support legs black coated Body RAL of choice, single-color Roll tarp RAL of choice, single-color Available in thermally insulated version!

Stanje: novo, številka stroja/vozila: 2f960ff7c44de83fd060ec5df, lastna masa: 6.750 kg, največja dovoljena obremenitev: 32.250 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 2.150 mm, prostornina tovornega prostora: 50 m³, skupna dolžina: 10.300 mm, skupna širina: 2.550 mm, skupna višina: 3.670 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, Further Information Chassis Semi-Trailer Tipper Fine-grained steel welded construction, lightweight basic design, fifth-wheel plate with exchangeable 2" kingpin Curved front end patented 24 t, two-speed landing gear, single-sided operation, with straight base, without thrust compensation Wheel chocks with holder Folding underrun protection Half-shell mudguards Integrated mudguard bracket, stone-repellent surface Tarp bar with holder Tow hook at rear Axles & Suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and traction aid Hot-dip galvanized lift axle mechanism, 10-year warranty against corrosion Braking System 2-line air brake system, color-coded piping for easy service Spring-loaded parking brake 2 foolproof coupling heads at front, without interconnection Dcodpfxei Rizfo Aiaoh EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractors that ensure the functionality of ABS! With raise/lower valve Vehicle driving stability system Wheels and Tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire pressure monitoring system (ECE R 141), display via screen in towing vehicle via EBS, not installed in truck (truck needs to be prepared; system only for original tires) Electrics 24 Volts, multi-chamber lights, side yellow LED lighting Side yellow LED lighting linked to turn signal, "flashing side markers" 2 x 7-pin foolproof sockets at front, without interconnecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operated hydraulically via truck PTO Body Steel half-pipe body made of highly wear-resistant HB 400 steel, sloped front wall with external hydraulic cylinder mount. Shovel and broom holders outside on the front wall. Climbing access inside at front wall. Side walls continuously 3 mm, floor continuously 3 mm thick Membrane rear wall Internal width at base approx. 1440 mm Aluminum rear wall, pendulum-mounted with "double joint hinge" and two-leaf door split (1/2 to 1/2), overhead swing bar, each door with its own grain chute Standing platform with access, connecting plate for air/electric and brake with large clearance for optimal operability Rolling tarp to be stowed to the right in direction of travel, with central locking on the left in direction of travel Approval Country/ Registration Germany Type approval in accordance with EC 2007/46 Body strength as per EN 12642 24/7 Service Hotline Prepared for single-line license plate holder Warning sign according to ECE-70 Contour marking with reflective strips acc. to ECE R 048, white on sides and red at rear Paintwork Frame: DB 7350 Novagrau "10-year warranty against corrosion" Body: Single color to RAL selection Rolling tarp: RAL 7035 light grey

Stanje: novo, številka stroja/vozila: 113bec9dd54d24fa34a088424, lastna masa: 4.400 kg, največja dovoljena obremenitev: 28.600 kg, skupna masa: 33.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.200 mm, višina nakladalnega prostora: 1.750 mm, prostornina tovornega prostora: 30 m³, skupna dolžina: 8.600 mm, skupna širina: 2.550 mm, skupna višina: 3.400 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, Further Information Chassis - Tipper Semi-Trailer Fine-grain steel welded construction, lightweight design, fifth wheel plate with replaceable 2" kingpin Curved front wall, patented 24 t, 2-speed support leg, single-sided operation, with straight base, without load equalisation 2 wheel chocks with holders Foldable underrun protection Half-shell mudguards Tarpaulin rod with holder 2 towing hooks at the rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axles / running gear laser-measured to reduce tyre wear and fuel consumption Axles in off-road version Air suspension 1st axle automatic lift axle, including forced lowering and start assistance Hot-dip galvanised lift axle mechanism, 10-year warranty against corrosion Brake System 2-line compressed air brake system, colour-coded pipe layout for easy servicing Spring-loaded parking brake 2 anti-interchange couplings at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connection cable Note: The trailer may only be towed by vehicles capable of ensuring the ABS functionality! with lift & lower valve Vehicle Stability Control System Wheels and Tyres 385/65 R22.5 tyres, make at manufacturer’s discretion Steel rims, factory silver "TPMS" Tyre Pressure Monitoring System according to ECE R 141, display via in-cab display through EBS, not installed on the truck (vehicle must be equipped for this; only standard tyres) Electrics 24 Volt, multi-chamber lights, lateral yellow LED lighting side yellow LED lighting synchronised with the indicator “flashing side marker lamps” 2 white clearance lights front 2 white/red lane assistance lamps rear 2 x 7-pin anti-interchange sockets at the front, without connecting cable Hydraulics Dcedji Rizispfx Aiajh Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck PTO Body (Tipper Bed) Aluminium box body made of high-quality, abrasion-resistant material, front wall thickness 5 mm, outer walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repelling upper edge profile; inside with access at the front wall (not in conjunction with Cramaro) Holder for shovel and broom outside on the front wall Greenline - conical and aerodynamic body shape Membrane rear wall Rear wall as pendulum flap with dual hinge, externally mounted with double hook locking Rear wall with rubber seal Note! Heat resistant up to max. 170°C! Continuously 6 mm strong floor Standing platform with access, connection plate for air/electricity and brakes with large free space for optimum operability Roll tarpaulin stored to the right-hand side, central locking on the left Country of Approval / Registration Germany with Dekra inspection and report (per §13 EC-FGV) 24/7 Service Hotline prepared for single-line licence plate holder Contour marking with reflective tape according to ECE R 048, white on the sides, red at the rear Paintwork Frame: DB 7350 Nova Grey "10 years warranty against perforation corrosion" Body: RAL code as requested, single colour Roll tarpaulin: RAL 7035 light grey

Stanje: novo, številka stroja/vozila: aaa375d3c15c697ac80fb51f9, lastna masa: 7.900 kg, največja dovoljena obremenitev: 31.100 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, širina tovornega prostora: 2.330 mm, višina nakladalnega prostora: 1.950 mm, prostornina tovornega prostora: 50 m³, skupna dolžina: 11.200 mm, skupna širina: 2.550 mm, skupna višina: 3.470 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22,5, Further information Chassis - Tipping Semi-Trailer Fine-grain steel welded construction, lightweight design, with slight cranking, kingpin plate fitted with replaceable 2" kingpin 24 t, 2-speed landing gear, single-side operation, with straight lower section, without compensation adjuster Wheel chocks with holder Folding underrun protection Half-shell mudguards Integrated mudguard holder with stone-repellent surface Tarp rod with holder Tow hook at the rear Axles & Suspension BPW disc brake axles with 430 mm disc diameter Laser-aligned axles/chassis to reduce tire wear and fuel consumption Air suspension 1st axle with automatic lift axle function, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism with 10-year anti-corrosion warranty Brake System 2-line compressed air braking system, color-coded pipe routing for easy service Spring-loaded parking brake 2 foolproof coupling heads at the front, without connecting pipe EBS (Electronic Braking System) with EBS socket at the front, without connection cable Note: The towed trailer may only be hauled by towing vehicles that ensure the effectiveness of the ABS! With lift and lower valve Vehicle stability control system Wheels & Tires 385/65 R22.5 Steel rims in factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via truck display, via EBS, not installed on truck (vehicle must be preequipped for this; only applies to standard tires). Electrics 24 volt, multi-chamber lights, yellow LED side lighting Yellow LED side lighting synchronized with indicators ("flashing side marker lights") 2 white position lights at the front 2 white/red lane guide lights at the rear 2 x 7-pin foolproof sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, base stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck PTO Body Steel trough made of highly wear-resistant HB 400 steel, sloped front wall with external hydraulic cylinder mount. Folding aluminium fender at front right for sliding tarp. Shovel and broom holder on outer front wall. Internal ladder at front wall. Side walls 4 mm thick throughout, floor 5 mm thick throughout Tailgate (membrane type) Rear wall with dual-wing doors split 1/2 to 1/2, with 1 slider in the right wing. With external locking bar and mechanical lower lock, Platform with access steps, connection plate for air, electrics and brakes with large free clearance for optimum usability. Roll tarp stored on front right, with central locking on front left. Registration/Country Plates Germany Type approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE-70 Dcedpfx Aiji Rizqjaeh Contour marking with reflective strips according to ECE R 048, side white and rear red Painting Frame: DB 7350 Novagrau 10-year anti-corrosion warranty Landing legs: coated black Trough: Single color as per customer RAL request Roll tarp: RAL 7035 light grey

Stanje: novo, številka stroja/vozila: 4499ca1b286f9f653066b5693, lastna masa: 4.900 kg, največja dovoljena obremenitev: 30.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.200 mm, višina nakladalnega prostora: 1.600 mm, prostornina tovornega prostora: 27 m³, skupna dolžina: 8.600 mm, skupna širina: 2.550 mm, skupna višina: 3.150 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R 22.5, Further Information Dedpei Ri Nijfx Aiajch Chassis Semi-Trailer Tipper Fine-grain steel welded construction, in basic lightweight design, kingpin plate with replaceable 2" kingpin Patented curved front panel 24 t, 2-speed landing gear, single-sided operation, with straight lower section, without thrust compensation Folding underrun protection Half-shell mudguards Rear tow hook Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/frame laser alignment to reduce tire wear and fuel consumption Axles in off-road configuration Air suspension 1st axle: automatic lift axle, including forced lowering and traction assist Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air brake system, color-coded line routing for easy servicing. Spring-actuated parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, Electronic Brake System with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve Wheels and Tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via in-cab display, through EBS, without truck installation (must already be installed in the truck; only for primary tire set) Electrics 24 Volt, multi-chamber tail lamps, side yellow LED lighting Side yellow LED lighting linked to indicator – "flashing side marker lamps" 2 x 7-pin swap-proof sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Activation hydraulically via truck PTO Tipping Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Slanting front wall with exterior hydraulic operation and ladder at the front. Greenline – conical and aerodynamic body shape Exterior shovel and broom holder on the front wall. Membrane rear wall Rear wall as pendulum flap with double-joint hinge, external mounting with dual hook locking. 2 clamping screws with toggle latches at the lower side edges. Side walls throughout 4 mm thick, floor 4/5 mm thick, wear- and weight-optimized construction. Standing platform with access ladder, connector plate for air/electrics and brakes with large open space for optimal operation. Manual roll tarp can be rolled one-sided to curbside right (FR), with central locking on curbside left (FR) Registration Country/Plates Germany with Dekra Inspection and Certificate (pursuant to §13 EG - FGV) Superstructure strength according to EN 12642 24/7 Service Hotline Prepared for single-row license plate holder Contour marking with reflective tape according to ECE R 048, lateral white and rear red Paintwork Frame in DB 7350 Novagrau 10-year warranty against rust-through Landing gear coated black Trough in RAL color of choice, single-color and subject to availability Roll tarp RAL color of choice, single-color Also available with hydraulic rear wall

Stanje: rabljeno, lastna masa: 5.933 kg, največja dovoljena obremenitev: 29.067 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, Condition – Very well-maintained vehicle from first ownership Category – Semi-Trailer Model – FLIEGL DHKA 350 – 35,000 kg Registration Month – 02 Registration Year – 2013 Gross Weight in kg – 35,000 Unladen Weight in kg – 5,933 Payload in kg – 29,067 Colour – Silver Number of Axles – 3 Maintenance – Inspection log Commercial/Export – Net price in € – 19,990 Subject to change, prior sale, and errors Phone: +49 551 50 84 912 According to Manufacturer Axles and Suspension SAF disc brake axles with 370 mm disc diameter; air suspension with raise and lower function; 1st axle is a self-lifting axle, including forced lowering and traction assist, operation via "3x braking" (traction assist operational up to 30% axle load excess and up to a maximum speed of 25 km/h) Chassis Special steel welded lightweight construction; fifth wheel plate with replaceable 2" kingpin Support gear/landing legs Not included Tyres/Rims 385/65 R 22.5” as selected by the manufacturer; polished aluminium rims as selected by the manufacturer Brake System Two-line brake system according to EC regulations; EBS; 2 mistake-proof coupling heads; spring-loaded parking brake; without connection cables Electrics 24 Volt, multi-chamber lights; 2 x 7-pin mistake-proof sockets; lighting according to EC regulations; without connection cables Hydraulics Low-pressure cylinder max. 170 bar with HDK screw coupling; fixed part, NW 48 mm (no hose connection) Body/Tub Djdpfx Aowk Ux Nsiajch Aluminium floor made from high-quality abrasion-resistant material, 5 mm thick, Brinell 110, reinforced with U-cross beams; side walls made with neatly welded hollow chamber profiles, with bulk material deflecting top rail; inclined front wall, rear wall as pendulum tailgate with "double hinge", mounted externally with dual hook locking. Note! Only suitable for transporting sand, gravel, and round pebbles up to a max. grain size of 20 mm! Warranty is excluded for all other transported goods! Paintwork Frame blasted, primed, and finished in single-colour 2K/HS acrylic paint in DB Novagrau; body in RAL 9010 pure white with Revolution letterings Other Folding underride guard; wheel chocks with holder; ½ shell plastic mudguards; with Dekra inspection and certificate (according to §13 EC - FGV); contour marking with reflective strips per ECE R 048, white on the sides and red at the rear; shovel and broom holders on the outside of the front wall

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 09/2008, skupna dolžina: 17.700 mm, skupna širina: 2.600 mm, vzmetenje: zrak, Leto izdelave: 2008, Dodatne informacije: Znamka: FLIEGL Model: SVS580T Zasnova: platforma (platforma D=13.211 mm / Š=2.540 mm / V=930 mm) Leto izdelave: 09.2008 Vzmetenje: zračno Zavore: bobnaste Dimenzije: D/Š: 17.700 mm / 2.550 mm Mase: skupna/prazna: 58.000 kg / 14.310 kg Letnik modela: 2008 Tip vzmetenja: zračno Zavore: bobnaste Dvižna os: dvižna os Krmiljenje: krmiljena = Več informacij = Vzmetenje: zračno vzmetenje Prednja os: dvižna os Srednja os 1: krmiljena Zadnja os: krmiljena Lastna masa: 14.310 kg Dsdpfxowkdmvs Aiaoch Nosilnost: 43.690 kg Dovoljeno skupno maso: 58.000 kg

Stanje: rabljeno, največja dovoljena obremenitev: 33.787 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2017, naslednji pregled (TÜV): 01/2027, dolžina tovornega prostora: 7.200 mm, širina tovornega prostora: 2.350 mm, skupna širina: 2.550 mm, Skupna teža: 39.000kg/35.000kg Lastna teža: 5.213kg Nosilnost: 33.787kg/29.787kg Skupna dolžina: 8.200mm Nakladalna dolžina: 7.200mm Širina: nakladalna širina 2.350mm / skupna 2.550mm Dodatne informacije: - Notranja višina kesona 1.450mm - Prostornina: 24,5 m³ - Višina pripenjanja: 1.200mm - Palica za ponjavo z nosilcem - BPW osi - Zračno vzmetenje - Jeklen okrogel keson v obliki kadi - Zadnja stena kot nihajna loputa - Ploščad s stopniščem - Enostranska rolo ponjava Vozilo je lahko polepljeno in/ali označeno z reklamami. Dcsdoycbi Rjpfx Aiash

Stanje: rabljeno, lastna masa: 7.950 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2013, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 2.850 mm, prostornina tovornega prostora: 95 m³, velikost pnevmatike: 385/55 R22,5, medosna razdalja: 1.310 mm, barva: črn, Oprema: ABS, Disc brake EBS Payload 27,050 kg Air lift suspension Sliding tarpaulin Platform SAF axles Alcoa aluminum rims Lifting and lowering device Lashing rings Dcodpfxsuiytls Aiash Subject to errors and omissions

Stanje: rabljeno, lastna masa: 7.950 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2013, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 2.850 mm, prostornina tovornega prostora: 95 m³, velikost pnevmatike: 385/55 R22,5, medosna razdalja: 1.310 mm, barva: črn, Oprema: ABS, Disc brake EBS (Electronic Braking System) Payload 27,050 kg Air suspension with lift axle Sliding tarpaulin Platform SAF axles Alcoa aluminum rims Djdpfx Aijuiyvyjajch Lifting and lowering device Lashing rings Subject to errors and omissions

Stanje: rabljeno, skupna masa: 18.000 kg, prva registracija: 09/2019, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.000 mm, - Dvojna montaža pnevmatik - Mega, - 3 metre notranje višine - Stranski naklad Dsdpfx Aoxxxltsiaech

Stanje: novo, številka stroja/vozila: 195f80ad09517628522e33a91, lastna masa: 7.300 kg, največja dovoljena obremenitev: 16.700 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Rear mudflaps across the entire width Quarter shell fenders in front of 1st axle 1st pair of wheel recesses embedded after the kink in the loading bed area, ramped entry, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! The frame in the main beam area is 400 mm higher than the wheel recess. Dedpfx Aioi Ri Rveajch 2nd pair of wheel recesses embedded between the axles in the loading bed area, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The frame in the main beam area is 300 mm higher than the wheel recess. Sliding extensions for widening, extendable to 3,000 mm (not in tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Sliding extensions for widening, extendable to 3,000 mm, also at the bottom in the wheel recesses, foldable at the wheel recess extensions (extension not in the tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) 70 mm timber planks for extension to 3,000 mm Tie-down points on low loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front in the kink, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for attaching tie-down straps) 7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated at 10 t 1x at the front in the kink 6x in the loading bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points no greater than 1,100 mm Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Axles & suspension SAF drum brake axles Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-applied parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, LED side marker lights, 2 white position lights at the front 2 white/red lane guidance lights at the rear 2 x 7-pin fail-safe connectors at the front, with connection cable, 1 LED rotating beacon with holder, switched via side light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Front kink with steel/checkered plate covering Storage box embedded in the ramp to the kink, then with 70 mm softwood floor, in the wheel arch area with steel/checkered plate covering Tail ramp with 70 mm softwood floor Low loading area including tail ramp: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring assist Operating Instructions For 10,000 kg axle load an exemption is required, only indivisible loads allowed! The stated gross weight is technically possible, but depending on the type of load, the gross weight may not be achievable within the pe

Stanje: novo, številka stroja/vozila: 6650f95fd39bb5625662ee336, lastna masa: 7.550 kg, največja dovoljena obremenitev: 27.450 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 385/55 r22.5, Further Information Chassis Semitrailer for Haulage Companies Fine-grain steel welded construction in lightweight design, reaching down to the landing legs, fifth wheel plate with replaceable 2" king pin Prepared for lashing eyes in the floor on the side (up to 13 pairs max.) 24 t two-speed landing gear, operated from one side, with straight base section, without stroke compensation Dcodpfx Aisi Riwxsaoh Slide-out ladder at the rear Side-mounted door retainers 2 wheel chocks with holders Aluminium side underrun protection Steel rear underrun protection with wide Fliegl mud flap, foldable splash guard for lighting unit Quarter round mudguards Rear impact protection Aluminium ladder approx. 3,550 mm with side holder Tarpaulin support bar with bracket 1 plastic toolbox with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) 1 spare wheel holder for 1 spare wheel, with wheel securing kit Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, operated by applying brakes 3 times (starting aid functional up to 30% axle overload and up to 25 km/h max. speed) Brake System 2-line compressed air brake system, colored piping for easy maintenance Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without interconnection EBS, Electronic Braking System with EBS socket at front, without connection cable Note: This trailer may only be towed by towing vehicles that ensure the functionality of the ABS! With lift & lower valve Vehicle Stability Control System Wheels and Tires 385/55 R22.5 tyres, brand at manufacturer’s discretion Steel rims, factory silver Electrics 24 Volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, without interconnection cable SB Hydraulics Hydraulic cylinder with sliding mechanism integrated in the floor. Dual-circuit hydraulics. Forward/reverse stroke selection is electric via cable remote control. Sliding floor power supply via parking light Actuation hydraulically via truck PTO Hydraulic connection with hose to front wall and HDK screw coupling NW = 48 mm Note: A dual-circuit hydraulic system is required! Recommended pump performance: Output: 110 l/min Pressure: 250 bar Oil tank capacity min.: 100 l SB Floor Sliding floor with wear plate at the rear Floor made of 8 mm aluminium planks, ribbed design SB Body Aluminium box-type body made of high-grade, wear-resistant material. Front and side walls made of aluminum hollow profiles, circumferential upper edge welded with a wide special reinforcement profile of aluminum, lower edge welded with a special frame. Moving bulkhead for better unloading of cargo, with reinforced tarpaulin apron at the bottom With rail cleaner Rear wall made of aluminum hollow profiles, as double-leaf door, split 1/2 to 1/2, circumferentially framed with special U-profile with stop and rubber seal, with 2 external locking rods, locked top and bottom. Rear wall with mechanical security lock, operated at the rear to the left in direction of travel. With swiveling cross-beam at top. The door locks are padlockable. Standing platform with ladders on both sides (left/right in direction of travel) and railing, for opening

Stanje: novo, številka stroja/vozila: 562ca26c733cc91276e95b716, lastna masa: 6.700 kg, največja dovoljena obremenitev: 28.300 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 385/55 r22.5, Further Information Chassis: Tractor Unit for Haulage Fine-grain steel welded construction in lightweight design, extending to the landing legs, fifth wheel plate with replaceable 2-inch kingpin Prepared lashing rings on the floor (max. 13 pairs) 24 t two-speed landing gear, single-sided operation, with straight lower section, without push compensation Extendable ladder at the rear Dsdpfx Aioi Riywjaoch Side door retainers 2 wheel chocks with holders Side underrun protection made of aluminium Rear underrun protection made of steel with wide Fliegl mudflaps, foldable guard for light units Quarter-shell fenders Rear impact guard Aluminium ladder approx. 3,550 mm, with side-mounted holder Tarp pole with mounting bracket 1 plastic toolbox with drawer and shelf, dimensions: 650 mm (W) / 520 mm (H) / 670 mm (D), lockable with padlock (padlock not included) 1 spare wheel holder for 1 spare wheel, including wheel fastening kit Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser alignment, reducing tire wear and fuel consumption Air suspension 1st axle is an automatic lift axle, including forced lowering and start assist, activated by braking three times (start assist functional up to 30% axle overload and up to a max speed of 25 km/h) Braking System 2-line compressed air braking system. Color-coded piping for easy servicing. Spring-actuated parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure ABS functionality! Including raise/lower valve Vehicle stability control system Wheels and Tires 385/55 R22.5, brand at manufacturer’s discretion Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, without connecting cable Moving Floor (SB) Hydraulic System Hydraulic cylinder with sliding device installed in the floor. Dual-circuit hydraulics. Forward/reverse control is electric via wired remote control. Moving floor power supply via parking lights Hydraulic operation by truck PTO Hydraulic connection with hose at bulkhead and HDK screw connector NW = 48 mm Note: A dual-circuit hydraulic system is required! Recommended pump performance: Flow rate: 110 l/min Pressure: 250 bar Minimum oil tank capacity: 100 l Moving Floor Moving floor with wear plate at rear Floor boards made of aluminum, 8 mm ribbed floor profile Moving Floor Body Aluminum box body, manufactured from high-quality, wear-resistant material. Front and side walls made of aluminum hollow profiles, completely welded at the top with a wide special reinforcement profile, and at the bottom with a special frame. Sliding wall for improved unloading, with reinforced tarpaulin flaps at the bottom. With rail sweeper Rear wall made from aluminum hollow profiles, two-wing door design, split 1/2 to 1/2, fully framed with a special U-profile including stop and rubber seal, with 2 external locking bars, locked top and bottom. Rear wall equipped with mechanical safety lock, operated at the rear on the left in driving direction. With swingable crossbar at the top. Door locks are padlockable. Standing platform with ladder access on both left/right sides (in driving direction) and railing for opening

Stanje: novo, številka stroja/vozila: 2dff0c136c85096f36822a0bb, lastna masa: 7.150 kg, največja dovoljena obremenitev: 16.850 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis - Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring, storage box integrated into turntable front section Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflaps Extendable extensions to 3,000 mm (not at the rear bevel) (Note: The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Central storage compartment for timber boards on the loading platform 70 mm timber boards for extension to 3,000 mm Low-bed lashing rings 3 pairs of 10 t lashing points integrated into the front floor 6 pairs of 10 t lashing mushrooms recessed in the top and side of the outer frame 1 x by the neck area The remaining points are distributed at no more than 1200 mm intervals 1 x at the rear bevel 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (can be converted to 5 t ring lashing eyes, not included) Drawbar Turntable Trailer Coupling Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical Axle load equalisation (rocker balancing) Brake System 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake included 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles ensuring the proper function of ABS! Wheels and Tyres 235/75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver finish Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, followed by 70 mm softwood flooring; wheel arch covers in steel/chequer plate Rear bevel with 70 mm softwood flooring Low-bed area incl. rear bevel 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered, included With spring assist Operating Notes An exemption permit is required for 10,000 kg axle load—only indivisible loads allowed! Dsdpfxsi Riy Eo Aiaoch The specified total weight is technically achievable, but depending on the load, the permissible total weight may not be reached due to axle/support/kingpin limits. (Poor driving and tracking may result from incorrect load distribution) Country of Registration/Plates Country of registration: Germany With Dekra inspection and appraisal (according to §13 EU-FGV) 24/7 service hotline Prepared for double-line license plate holder Contour marking with reflective stripes per ECE R 048, white to the side, red to the rear Paintwork Frame DB 7350 Novagrau 10-year guarantee against rust-through Drawbar galvanized or black, manufacturer's choice Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 2dee9cc4124b79c4820f5c3cf, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 385/65 r22.5, Further information Fine-grained steel welded construction, fifth wheel plate with interchangeable 2-inch kingpin, exterior frame slightly angled, new design with Load-Lock profile for securing lashing straps, 24t 2-speed landing gear, operation from one side, with straight lower section, without traction equalizer Note: Free support foot corner dimension or free rear swing radius approx. 1930 mm, pull-out ladder at the rear, door holders on the sides, 2 wheel chocks with holders, Side underrun protection made of aluminium, rear underrun protection made of galvanized steel, quarter shell mudguards in front of and behind the axle assembly, with EG-compliant anti-spray mudflaps, rear impact protection SAF disc brake axles with 430 mm disc diameter, axles/chassis laser aligned to reduce tyre wear and fuel consumption, air suspension 2-line compressed air brake system, color-coded pipe layout for easy servicing, spring-loaded parking brake, 2 non-interchangeable coupling heads at front, without connection line, EBS, electronic braking system with EBS socket at the front, without connecting cable, Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With lift & lower valve, vehicle stability system 385/65 R22.5 tires, brand at manufacturer’s discretion, steel rims, factory silver 24 volt, multi-chamber lights, yellow LED side marker lights, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 2 x 7-pin non-interchangeable sockets at front, without connection cable, Floor: phenolic plywood approx. 30 mm thick, on longitudinal cross members for high point load capacity, for forklift axle load up to max. 7100 kg Front bulkhead / front corner posts: 2, 580 mm high, steel corner posts, volume design, quick-release system for side curtain at bulkhead, crash blocker, lower interior approx. 140 mm high with steel impact protection Centre posts: 3 pairs of sliding uprights, adjustable along the full length, with 4 insert pockets and long pocket at the bottom, 3 pairs of upright positions Insert slats: 5 rows of wooden insert slats Djdpfx Aei Riy Teiajch Rear wall / rear corner posts: rear corner posts steel up to lower edge of roof, curtain mounting with round tube and tensioning ratchet, rear portal doors, double-winged, each with 2 internal locking bars Tarpaulin: tarpaulin with welded horizontal and vertical belts, tension locks of stainless steel Roof: sliding roof, rear end liftable, roof can be shifted from rear to front, L crossmembers for automotive industry, interior width between roof crossmembers approx. 2,490 mm, tarpaulin color: white, 400 Roof non-elastic, minimal sag of roof crossmember during loading and unloading, optimal rear rain gutter above the doors at end post at the top Germany, type approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer certificate for body strength as per EN 12642 XL, prepared for single-line license plate holder, warning plate according to ECE-70, reflective tape: white, continuous along lower edge of side curtain and upper corners (if visible drop sides, tape at lower edge on sides), reflective tape: red, all around rear portal Frame DB 7350 nova grey, 10-year warranty against rust-through, support feet black coated, front corner posts hot-dip galvanized, front wall aluminium, rear corner posts hot-dip galvanized, rear wall white, tarpaulin RAL of choice, single-color, subject to availability Attention: Archive pictures!

Stanje: novo, številka stroja/vozila: ede0610378cbe39cc4883251d, lastna masa: 24.000 kg, največja dovoljena obremenitev: 7.550 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-loader Trailer Steel welded construction 1st pair of wheel recesses embedded in the driving lane area after the steel platform, bevelled for entry, approx. 1,400 mm long at the bottom, approx. 400 mm deep. Note! Frame is 400 mm higher in the main beam area than at the wheel recess. If machines are to be transported where overall height must be verified, we request a technical data sheet for the machine types with precise specifications (if overall height is exceeded -> customer is responsible, approval required). Depending on ground clearance under the machines, inserts for the wheel recesses may be required on the customer side. Turntable with robust ball race ring, storage box integrated in the turntable front section Rear supports foldable 2 wheel chocks with holder Aluminium side underrun protection Full-width rear mudflap Extending wideners to 3,000 mm (not in rear bevel area) (The track width of the construction machines or vehicles to be transported must not exceed the outside frame width of 2,550 mm) Dsdpfx Aei Ri Ryoiaech Central storage compartment for wooden planks on loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes low-loader 3 pairs of 10 t lashing points integrated in the floor at the front incl. 6 pairs of lashing mushrooms recessed on top and at the side in the outer frame, each 10 t 1 x at the gooseneck The remaining distributed between, spacing not greater than 1,200 mm 1 x rear bevel 5 pairs of stake pockets integrated into the outer frame, internal 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly trailer turntable Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser aligned to reduce tyre and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colour-coded piping for easy service Spring loaded parking brake 2 interchange-proof coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by tractor units which ensure the functionality of ABS! Wheels and tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED illumination 2 white position lights at front 2 white/red track marker lights at rear 2 x 7-pin interchange-proof plugs at front with connecting cable 1 LED beacon with bracket, switched via parking light (removable lamp) 2 pairs of double warning boards, LED-lit and extendable up to 3,000 mm Floor Front area steel floor, incl. Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-loader deck incl. rear bevel 8,200 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring lifting aid Operating instructions For 10,000 kg axle load, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achievable while complying with permissible axle/kingpin/saddle loads. (Poor driving and tracking behaviour possible due to incorrect load distribution) Country of registration / Plates Country of registration: Germany incl. With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for two-line number pla

Stanje: novo, številka stroja/vozila: b50cac2c60a813b0968994fa0, lastna masa: 5.700 kg, največja dovoljena obremenitev: 18.300 kg, skupna masa: 24.000 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Full-width rear mudflap Preparation for widening to 3,000 mm (holes in outer frame, not in rear bevel) Low-loader lashing rings 1 pair of lashing cutouts embedded in the front longitudinal beam at the gooseneck, each rated for 10 t 7 pairs of lashing mushroom pins embedded on top and side of the outer frame, each rated for 10 t 1 x on the front gooseneck 5 x in the low-bed area 1 x in the rear bevel 12 pairs of lashing holes in the outer frame, each rated for 5 t (for lashing strap hooks) 5 x at the gooseneck, 6 x in the low-bed area, and 1 x in the rear bevel Drawbar system for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles, brand as per manufacturer’s choice Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 unmistakable coupling heads at the front, with connecting lines to the truck, Connecting lines extended by approx. 60 cm No ABS, but with mechanical ALB (automatic load-dependent brake valve), thus maximum 60 km/h permit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 7-pin 12 Volt plug at the front with connecting cable, extended by approx. 60 cm 1 LED beacon with holder, operated via parking light (lamp removable) 2 pairs of illuminated and extendable warning plates up to 3,000 mm Floor Front gooseneck with steel/chequer plate covering Toolbox recessed in the drive-over slant to gooseneck Following area with 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-bed loading area including rear bevel: 5,900 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Dcsdpji Ri Agofx Aiaoh Wooden covering Spring-assisted lifting Operating Instructions For axle loads of 10,000 kg, an exemption permit is required; only indivisible loads permitted!!! The stated total weight is technically possible; depending on the load, the total weight may not be achievable within the allowable axle/support and fifth wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate for max. 60 km/h approval, towing vehicle as agricultural/forestry vehicle (LoF), (for Switzerland, max. 40 km/h possible) Prepared for double-line license plate holder No contour markings / reflective tape according to ECE R 048 Painting Frame: DB 7350 Novagrau 10-year corrosion protection warranty Drawbar galvanized or black, according to manufacturer’s choice Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: d461243f559015adca5bb372c, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflap Dcjdpoi Ri Dlsfx Aiaoh Half-shell mudguards on 1st axle with anti-spray mudflaps Anti-spray mudflaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: W=620/H=360/D=440 mm, lockable with a padlock Extendable width up to 3,000 mm Central storage compartment for timber planks on loading area 70 mm timber planks for widening to 3,000 mm Lashing rings for low-bed (40 lashing points) 1 pair of lashing apertures recessed in the front longitudinal beam at the gooseneck, each rated for 10 t 4 pairs of lashing holes in the external frame, each rated for 5 t (for lashing strap hooks) 7 pairs of lashing mushrooms embedded on top and side of the outer frame, each rated for 10 t 1 at the front on the gooseneck 6 in the low-bed section First lashing ring 250 mm from the front, last max. 250 mm from the rear, spacing between lashing rings not greater than 1,100 mm 5 pairs of stake pockets embedded in the external frame, internal dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes) 2 pairs of additional folding lashing eyes, each rated for 10 t 1 on the gooseneck (protruding) 1 recessed behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 40 mm towing eye Axles + Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and tyres 235/75 R 17.5 Manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line pneumatic braking system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connecting lines to towing vehicle ABS and ALB, ABS connector at the front with connecting cable Brand: Wabco, Knorr or Haldex Electrics 24 Volt, multi-chamber rear lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with bracket, controlled via parking lights (removable beacon) 2 pairs of warning boards, double, LED illuminated, extendable to 3,000 mm Floor Gooseneck front with steel tread plate covering Storage box recessed in the transition to the gooseneck Followed by 70 mm softwood flooring, wheel arch areas with steel tread plate covering Rear chamfer with 70 mm softwood flooring Low-bed area incl. rear chamfer: 6,500 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber-layered Hydraulically operated via tractor PTO with throttle, operated from left-hand side, front Hydraulic connection with SVK coupling NW 10/3, including connecting hose Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Warning board according to ECE - 70 Paintwork Frame hot-dip galvanized incl. passivation 15-year warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Note: These are archive images!

Stanje: novo, številka stroja/vozila: 8e6cf81e11b107f23f22f209a, konfiguracija osi: 3 osi, velikost pnevmatike: 435/50 r19.5, Further Information Fine-grain steel welded construction, with preload light pretensioning in the neck area, fifth wheel plate with interchangeable 2" kingpin, outer frame slightly angled new version with load-lock profile for lashing strap attachment, 24-ton 2-speed landing gear, single-sided operation, with straight lower section, without sliding compensation. Note: Free landing leg corner dimension or free rear swing radius approx. 1930 mm, extending ladder at rear, door holders on the side, 2 wheel chocks with holders, side underrun protection in aluminum, underrun guard in galvanized steel, quarter shell mudguards in front of the first axle and behind each axle, with anti-spray flaps as per EC regulations, rear impact protection. SAF disc brake axles, axles/chassis laser-aligned to reduce tire wear and fuel consumption, air suspension. 2-line compressed air brake system, color-coded line routing for easy maintenance. Spring-actuated parking brake, 2 mistakable-proof coupling heads at front, without connecting line, EBS, electronic braking system with EBS socket at the front, without connecting cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With raise & lower valve, vehicle stability control system. 435/50 R19.5 tires, brand as chosen by manufacturer, steel rims, factory silver. 24 Volt, multi-chamber lights, side yellow LED lighting, 2 white position lights at front, 2 white/red side marker lights at rear, 2 x 7-pin mistakable-proof sockets at front, without connecting cable. Floor: Phenolic plywood panels approx. 30 mm thick, laid on longitudinal crossmembers for high point load capacity, suitable for forklift axle loads up to max. 7100 kg. Front wall / front corner posts: 2,580 mm high, corner posts in steel, high-volume design, quick-release system for side curtain at front wall, crash blocker, interior lower ram protection in steel approx. 140 mm high. Dcodpfxji Ri E He Aiash Center posts: 3 pairs of sliding posts movable along the entire length, with 4 stake pockets each and long pocket below, 3 pairs of post positions. Insert slats: 5 rows of wooden slats. Rear wall / rear corner posts: Rear corner posts in steel up to lower roof edge, curtain mounting with round tube and curtain tensioner ratchet, rear portal doors, double-wing, each with 2 internal locking bars. Tarpaulin: Tarpaulin with welded-in horizontal and vertical straps, tension locks in stainless steel. Roof: Sliding roof, rear end lift foldable upwards, roof can be slid from rear to front, L-profile roof beam for automotive industry, interior width between roof beams approx. 2,490 mm, tarpaulin color: white, 400 roof non-elastic, minimal roof beam deflection during loading and unloading, optimal rain gutter at rear, top of the end bow above the doors, EcoLift – lifting roof can be raised by approx. 380 mm, with gas strut assistance, 3 driving positions at front: internal height at front approx. 2,900 mm / 2,950 mm / 3,000 mm, set to approx. 3,000 mm. Germany, type approval as per EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for body strength as per EN 12642 XL, prepared for single-line license plate holder, warning sign as per ECE-70, reflective tape: white, continuous at the lower edge of the side curtain and at the top corners (if visible sideboards, stripe at the bottom of sideboards), reflective tape: red, all around the rear portal. Frame DB 7350 Nova grey, 10-year anti-corrosion warranty, land

Stanje: novo, številka stroja/vozila: f044065451f6d849ee7a5b9f8, lastna masa: 5 kg, največja dovoljena obremenitev: 29 kg, skupna masa: 35 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 385 / 65 r 22,5, Further information Chassis, Semi-Trailer, Forwarder Steel welded construction in reinforced design, only 2 longitudinal members as double T-beams with steel/chequered plate between the longitudinal members, fifth wheel plate with interchangeable 2-inch kingpin. Protective cover for rear lights. 1 steel toolbox, recessed between longitudinal members 8 pairs of lashing rings bolted or welded to the frame, as per manufacturer’s choice 24t, 2-speed landing gear, single-sided operation, with straight base plate, without load equalizer 2 wheel chocks with holders Side underrun protection made of aluminium Rear underrun protection galvanized steel Half-shell mudguards With anti-spray mud flaps according to EC standard 1 spare wheel carrier for 1 spare wheel, with wheel fastening kit 8 pieces of timber bolsters (according to manufacturer’s specification), bolted to the frame, each with 2 telescopic wooden stakes 1800 to 2800 mm, 7t per pair. Axles & Suspension SAF disc brake axles with 430 mm disc diameter Air suspension with raise/lower valve, safety cable on the axles Dcodpfx Aoi Rivwsiaeh 1st axle automatic lift axle, including forced lowering and drive-off aid, activation by braking 3x (Drive-off aid functional up to axle overload of 30% and up to a max. speed of 25 km/h) Axle spacing offset mm (Combined transport) up to a total tractor weight of 44t Wheels and Tyres 385 / 65 R 22.5 At manufacturer’s discretion Steel rims, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS CAN bus signal, for display in the truck cab (truck must be pre-equipped, no truck sensor included, not a calibrated scale) 2 reverse-polarity safe coupling heads at front, without connecting lines EBS, Electronic Braking System with EBS socket at front, without connecting cable Note: The towed vehicle may only be operated by towing vehicles that guarantee the effectiveness of the ABS! Electrics 24 V, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin and 1 x 15-pin reverse-polarity safe sockets at the front, without connecting cables Front wall/corner posts Steel/grating front wall, approx. 2300 mm high, bolted to the frame Approval / Markings Country of registration: Germany Approval according to EC 2007/46 Prepared for single-line number plate holder Contour marking with reflective tape according to ECE R 048, side white and rear red Paintwork Frame DB 7350 Nova Grey Landing legs coated black Front wall hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 068983c41e44eb5660fa9100c, lastna masa: 6 kg, največja dovoljena obremenitev: 28 kg, skupna masa: 35 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 435/50 r19,5, Further Information Chassis, Fifth-Wheel, Logistics Fine-grained steel welded construction, with preload for slight neck area pretension, fifth wheel plate with replaceable 2" kingpin X-tra Long, with 15,030 mm internal length New type slightly inclined outer frame with Load-Lock profile for securing lashing straps 24 t twin-speed landing gear, operable from one side, with straight lower section, without compensating device Note: Free support foot external dimension or free rear swing radius approx. 1,930 mm Extending ladder at rear Lateral door retainers 2 wheel chocks with holder Side underrun protection, aluminium Rear underrun protection, galvanized steel Quarter mudguards in front of the first axle and behind each axle Rear impact guard Axles + Suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Air suspension Brake System Dual-line compressed air brake system Colour-coded line routing for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability system AAC Basic, automatic lift axle working on last axle, maneuvering aid, up to 20 km/h, can be switched off manually Axle load detection via EBS CAN-bus signal, for display in the driver’s cab, truck must be preconfigured accordingly; not installed (not a certified scale) Wheels and Tyres 435/50 R19.5, brand at manufacturer's discretion Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, yellow LED side lighting Side yellow LED lighting linked with indicators, flashing Side marker lights 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin fail-safe sockets at the front, without connecting cables Floor Phenolic plywood, approx. 30 mm thick, on longitudinal subframes for high point load capacity, suitable for forklift axle loads up to max. 7,100 kg Front Wall / Front Corner Raves 2 pieces, 580 mm high, steel corner raves in high-volume design, release device for side curtain at bulkhead, crash blocker, inner steel rear impact guard at approx. 140 mm height Centre Stanchions 3 pairs of sliding stanchions moveable along full length, with quadruple pocketing and long lower pocket 3 pairs of stanchion positions Insert Slats 5 rows of wooden insert slats Dedpfxoi Riwue Aiasch Rear Wall / Rear Corner Raves Rear corner raves, steel up to lower roof edge, fitting for curtain with round tube and curtain tension ratchet Double-winged tail doors, each with 2 internal locking bars Curtain Curtain with welded horizontal and vertical straps Tension closures made of stainless steel Roof Sliding roof, rear end-lift foldable, canopy can be slid from rear to front, L-roof beam for automotive industry, clear internal width between roof beams approx. 2,490 mm, curtain colour: white Roof non-elastic, minimal deflection of roof beam during loading and unloading EcoLift - hydraulically liftable roof by approx. 380 mm on both sides, gas strut-assisted 3 driving positions at the front: Internal height at front approx. 2,900mm / 2,950 mm / 3,000 mm, set to approx. 3,000 mm Optimized rain gutter at rear, upper end spar, above doors Operating Instructions Special permit required if total train length exceeds 16,500 mm. When assembling the truck and trailer combinations, ens

Stanje: novo, številka stroja/vozila: 628cde0fe99cc2d3c8eaa8dd8, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear spray flap Half-shell mudguards on 1st axle with anti-spray flaps, anti-spray flaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: width=620 mm / height=360 mm / depth=440 mm, lockable with padlock (padlock not included) Extendable width up to 3,000 mm Storage compartment for wooden planks in the centre of the loading area 70 mm wooden planks for extension to 3,000 mm Tie-down lugs for low loader (40 lashing points) 1 pair of lashing cut-outs in the longitudinal beam at the front, recessed into the gooseneck, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for securing with lashing straps) 7 pairs of lashing mushrooms, recessed at the top and side of the outer frame, each rated at 10 t 1 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front, last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, interior dimensions 70 x 40 mm (convertible to 5 t ring lashing points, not included) 2 additional pairs of folding lashing rings, each rated at 10 t 1 on the gooseneck (protruding) 1 behind the last axle, recessed in the floor Towing Device Turntable Trailer Drawbar with certified 40 mm towing eye Axles and Suspension Drum brake axles, manufacturer’s choice Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalisation (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims, twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front with connecting lines to the tractor unit ABS and ALB, with ABS socket at the front and connecting cable Manufacturer: Wabco or Knorr Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with bracket, switched with parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/chequer plate covering Toolbox recessed into transition slope to gooseneck Following area with 70 mm softwood floor, steel/chequer plate in wheel arch area Rear taper with 70 mm softwood floor Low-loader deck including rear taper: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber surfaced Dcjdoi Ri Ddepfx Aiaoh With spring lift assistance Country of Registration / License Plates Country of registration: Germany 24/7-Service Hotline Prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on sides, red at rear Warning sign according to ECE-70 Painting Frame hot-dip galvanized including passivation 15 years’ warranty against corrosion perforation Drawbar galvanized or black, manufacturer’s choice Loading ramps hot-dip galvanized Attention! Archive images shown!

Stanje: novo, številka stroja/vozila: abc6276e1749f9dddc494eb32, lastna masa: 4.900 kg, največja dovoljena obremenitev: 30.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 385/65 r22,5², Further Information Chassis Semi-Trailer Tipper Fine-grain steel welded construction, lightweight design, fifth wheel plate with replaceable 2-inch kingpin Patented curved front section Central telescopic support leg, uncoupling with load not possible; when uncoupled, the vehicle must be positioned with a rearward slope. 2 wheel chocks with holders Folding underrun protection Half-shell mudguards Integrated mudguard bracket, stone-repellent surface With anti-spray splash flaps only on the last axle 1 tarpaulin support bar with holder Dodpfsi Ri H Iox Aiaoch 2 towing hooks at the rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axles/chassis laser-aligned to reduce tire wear and fuel consumption Axles in off-road configuration Air suspension 1st axle automatic lift axle, including forced lowering and traction aid, activated by braking three times (traction aid functional up to a 30% axle load exceedance and to a maximum speed of 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against corrosion Brake System 2-line compressed air braking system, color-coded lines for easy maintenance Spring-loaded parking brake 2 foolproof coupling heads at the front, without connecting line EBS electronic braking system with EBS socket at the front, without connection cable Note: The towed vehicle may only be towed by towing vehicles that ensure the function of ABS! With lift & lower valve Vehicle - Driving Stability System Automatic tipping lowering with shut-off valve Wheels and Tires 385/65 R22.5, brand at manufacturer's discretion Steel rims, factory silver Electrics 24 volts, multi-chamber lights, yellow LED side lighting 2 white position lights at the front 2 white/red lane marker lights at the rear Two 7-pin foolproof sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck PTO Bodies Aluminum box body made of high-quality, wear-resistant material; front wall 5 mm thick, with external wall panels made of 30 mm hollow chamber profiles, neatly welded, with bulk material-repellent top rail profile. Access inside at the front wall (not in combination with Cramaro). Shovel and broom holder on the outside of the front wall. Greenline - conical and aerodynamic body shape Membrane rear wall Rear wall as swinging tailgate with double hinge, externally mounted with double hook locking. Rear wall with rubber seal Note: Heat resistant up to max. 170°C! Floor throughout 6 mm thick Access platform with steps, connection plate for air/electric and brakes with ample free space for optimal operability Roll tarp can be stored on right side (FR-right), with central locking on (FR-left) Operating Instructions For transports of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent corrosion caused by the material. The specified total weight is technically feasible; depending on the cargo, the total weight may not be achievable within the permitted axle, support, and coupling loads. (Poor handling and tracking due to incorrect load distribution possible) Registration Country/Plates Germany Certification in accordance with EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tapes in accordance with ECE R 048, white on the sides and red on the rear.