Müller-Mitteltal Odprta Platforma nakup rabljenega (267)

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brake System: Lhodpou I Iq Ejfx Aqpsn * EBS braking system * Drum brakes * Emergency release device for spring brake cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange Eye: * Drawbar with 40 mm bolted towing eye (height-adjustable mm) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring system ----General Attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate. Safety locking pins for various support heights * Closed steel mudguards with spray protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with floor inlay (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, clear width between drum arms 1,700 mm, with tension lock on the drum arm ends, plus central claw lock securing the cable drum superstructure to the chassis * Motor-driven hydraulic cable drum drive with oil motor * Valves and movable, rubber-coated drive rollers * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of polyamide centering cones, stepped ----Chassis: * Chassis made from torsion-resistant square tubing and cross beams ----Pump Unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tyres: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized ----Notes: * New vehicle with full manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brakes: * EBS brake system * Drum brakes * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange eye: * Drawbar with 40 mm screwed towing eye (height adjustable mm) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring ----General attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate; safety locking pins for various support heights * Closed steel sheet mudguards with splash protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Superstructure: * Pivoting cable drum superstructure, clear width between drum arms 1,700 mm, with tension locks for securing the drum at the ends of the support arms, and central claw locking device securing the drum superstructure to the chassis Lhsdpfsu I Iqljx Aqpen * Motor-hydraulic drum drive with oil motor * Valves and movable, rubber-covered drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of stepwise offset centering cones made of polyamide ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: Ljdpfx Asu I Iqxeqpohn ----Brakes: * EBS braking system * Drum brakes * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Coupling Eye: * Drawbar with 40 mm bolted towing eye (height-adjustable) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring system ----General Attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate, safety lock pin for various support heights * Enclosed steel mudguards with spray protection * Enclosed side underrun protection usable as advertising panel * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Body: * Swiveling cable drum body, clear width between drum arms 1,700 mm, with tension lock for securing drums at the support arm ends, as well as a central claw lock to secure the cable drum body to the chassis * Motor-hydraulic drum drive with hydraulic motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter including centering and rotating ends * 1 pair of polyamide centering cones, stepwise offset ----Chassis: * Chassis made of torsion-resistant square tubes and cross beams ----Pump Unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale reserved ----Delivery Time: * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 3.650 kg, največja dovoljena obremenitev: 10.750 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 07/2011, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 285/70R19.5, barva: bela, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, tandem, air suspension, ABS (anti-lock braking system), tailgate, lashing eyes, underrun protection, front support legs, rear support legs, pendulum tailgates, height-adjustable drawbar. Body: Tandem 3-way tipper trailer with aluminium sideboards, 2x Gigant axles, drum brakes! Ljdpozr H Ngofx Aqpehn Loading ramps available at an additional cost of €990.00 net! ACCESSORY INFORMATION WITHOUT GUARANTEE. Subject to change, prior sale, and errors excepted!

Stanje: rabljeno, lastna masa: 3.500 kg, največja dovoljena obremenitev: 9.500 kg, skupna masa: 13.000 kg, konfiguracija osi: 2 osi, prva registracija: 11/1993, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.200 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, barva: oranžna, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Lokacija vozila: Bovenden, jeklena nadstavba, 2 osi, tandem, listnata vzmetna vzmet, pritrdilne točke, zaščita podvozja, oporni mehanizem na sprednji strani, nihajne zapornice. Nadstavba: Tandem, 3-stranski nakladalni prikolica. Rezervno kolo na voljo proti doplačilu! PODATKI O DODATNI OPREMI SO NAVEDENI BREZ GARANCIJE, pridržane spremembe, vmesna prodaja in napake! Lsdpfx Aqozgu Sfepjhn

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18,0: * 3 v 1 = za prevoz zabojnikov za odlaganje in dvigovanje ter kot nizkopodna prikolica ----Zavore: * EBS-E (električni zavorni sistem) * Naprava za hitro sprostitev zavor za vzmetne zavorne cilindre * Bobnaste zavore ----Osje: * 2 x 10,5-tonski osi Gigant ----Vzmetenje: * Zračno vzmetenje z ročnim spuščanjem zadnje osi *pneumatična vlečna priprava, dolžina 2.100 mm, z 40 mm vtičnico in nastavitvijo višine ----Elektrika / Osvetljava: * Sistem za nadzor tlaka v pnevmatikah (RDÜ), možnost prikaza na zaslonu tovornjaka prek signala EBS (brez namestitve na strani tovornjaka) * LED zadnje luči 12 / 24 V * 15-polni vtič ----Splošni dodatki: * Orodjarna škatla iz prašno barvane jeklene pločevine * Nosilec rezervnega kolesa na desni strani, vgrajen v stransko konstrukcijo * Zaprt stranski odbijač * Plastični stranski blatnik z zaščito proti brizganju * Plastični odbijač zadaj * Zložljiv opozorilni znak zadaj ----Nosilna površina: Lodpfjl Tnwzjx Aqpshn * Vroče pocinkana glavna konstrukcija z dvignjenimi stranskimi okvirji za vodilo zabojnikov * Jeklena pločevinasta podlaga z vdolbinami za valje v območju podvoznika * Pri prevozu zabojnikov za odlaganje in dvigovanje je možna dolžina 5.500 - 7.000 mm * Pnevmatična 4-točkovna zaklepna naprava ter mehanska, vstavljiva oporna kota spredaj v vodilu * Možen prevoz do 2 zabojnikov za odlaganje in dvigovanje z največjo prostornino 10 m³ * 8 premičnih opornih točk za stransko centriranje zabojnikov, sprednje 4 oporne točke so vstavljene z nihajno oporo * Varjena plast za preprečevanje zdrsavanja v območju rampe * Mehanske oporne noge zadaj ----Pritrditev tovora: * 3 pari 10-tonskih UVV pritrdilnih zank na obeh straneh za pritrditev pritrdilnih elementov za obliki in mehansko pritrjevanje zabojnikov, vsaka z 4 pritrdilnimi pasovi v obliki deteljice (stransko) * 1 par 13,4-tonskih UVV pritrdilnih zank spredaj * Na obeh straneh 4 x 8-tonske pritrdilne točke, vgrajene v stranski okvir ----Rampe: * Aluminijaste nakladalne rampe (10,6 t / par), 2.800 x 470 mm, primerne za vozila z gumijastimi in goseničnimi pogoni (zaklenljiv prostor za shranjevanje zadaj) ----Barvanje: * Odsevni varnostni trak na straneh in zadnji strani * Okvir vroče pocinkan * Osje in vlečna priprava, črno barvani ----Informacije: * Certifikat za pritrditev tovora po standardu DIN 30722-1 * Certifikat za pritrditev tovora po standardih DIN EN 12195-1, DIN EN 12640, DIN EN 12642 in VDI 2700 * --Dovoljena skupna masa 20.000 kg, tehnično izvedljivo-- * Novo vozilo brez prve registracije z garancijo proizvajalca * Pridržujemo si pravico do sprememb in napak ----Dobavni rok: * Takoj na voljo iz Egstorfa

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18,0: ?3 v 1 = za prevoz zabojnikov za odlaganje, prevoz s prikolico in kot nizkotlačna prikolica ----Zavore: * EBS-E (električni zavorni sistem) * Naprava za hitro sprostitev zavor za vzmetne akumulatorje * Bobnaste zavore ----Osi: * 2 x 10,5 t ose Gigant ----Vzmetenje: * Zračno vzmetenje z ročnim spuščanjem zadaj ----Povezava vlečnega stroja: * Pnevmatično spuščana povezava vlečnega stroja, dolžina 2.100 mm, z 40 mm vtičnico in nastavitvijo višine ----Elektrika / Osvetlitev: * Sistem za nadzor tlaka v pnevmatikah (TPMS), možnost prikaza na tovornjaku preko signala EBS (brez namestitve na tovornjaku) * LED zadnje luči 12 / 24 V * 15-polni vtič ----Splošni dodatki: * Orodjarna omara iz jeklene pločevine s prašnim premazom * Nosilec za rezervno kolo, stranska izvedba na desni strani * Zaprt stranski zaščitni element * Plastični blažilnik na prednjem delu * Plastični blažilnik na zadnjem delu * Zložljiv opozorilni znak na zadnji strani ----Nosilna površina: * Vroče pocinkano glavno ogrodje z dvignjenim zunanjim okvirjem za vodenje zabojnikov * Jeklena pločevina s poglobitvami za valje na področju podvozkja * Pri prevozu zabojnikov za odlaganje je možna dolžina 5.500 - 7.000 mm * Pnevmatična 4-delna sponka za zaklepanje ter mehanska, vstavljiva oporna kota spredaj na nosilni površini * 1 prevoz do 2 zabojnikov za odlaganje z največjo prostornino 10 m³ je možen * 8 vstavljivih opornih elementov za stransko centriranje zabojnikov, prednji 4 oporni elementi so vstavljeni z možnostjo nihanja * Varjena plošča kot protizdrsna prevleka na nosilni površini nakladalne rampe * Mehanske podpore na zadnji strani ----Varovanje tovora: * 3 pari 10 t jeklenih zank UVV na straneh za pritrditev napenjalnih elementov za varno pritrditev zabojnikov, vsak par ima 4 jeklene zanke v obliki deteljice (stransko) * 1 par 13,4 t jeklenih zank UVV spredaj * Na vsaki strani 4 x 8 t jeklene zanke, vgrajene v zunanji okvir ----Rampe: * Aluminijaste nakladalne rampe (10,6 t / par), 2.800 x 470 mm, primerne za vozila s gumijastimi in goseničnimi pogoni (zaključljiv prostor za shranjevanje na zadnji strani) ----Barvanje: * Odsevni obod na straneh in zadnji strani * Okvir vroče pocinkan * Osi, povezava vlečnega stroja, pobarvane v črno barvo ----Informacije: * Potrdilo o varnosti tovora v skladu s standardom DIN 30722-1 * Potrdilo o varnosti tovora v skladu s standardi DIN EN 12195-1, DIN EN 12640, DIN EN 12642 in VDI 2700 * --Dovoljena skupna teža 20.000 kg, tehnično možno-- * Novo vozilo brez prve registracije z garancijo proizvajalca * Pridržujemo si pravico do sprememb in napak ----Dobavni rok: * Takoj na voljo iz Egstorfa Ledpfx Ajl Tld Ieqpjhn

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Brakes: * Without ABS/EBS, approved for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: * Tandem equalization unit with 100 mm wide parabolic springs ----Drawbar / Drawtube: * Fixed welded drawtube with low-maintenance ball joint for K80 ball coupling (offset by +77 mm / 33 mm via head plate), with raised bracket for connection lines ----Electrics / Lighting: * 12 V, 7 + 4 pin power supply * LED lighting system 12 / 24 V with protective grid * 2 LED work lights at the rear, switchable from towing vehicle without installation on towing side ----General attachments: * Support winch at the front * Mechanical drop-down supports at the rear * Side marker lights with indicator activation Lhjdpfsr Dpzuex Aqpjn * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right side * Hot-dip galvanized two-step access ladder in front of the front wall (on FR left) ----Chassis: * Fine-grain steel chassis ----Tipper body: * Steel Pal.- 3-way tipper body with M-Strong side panels (front wall fixed, continuous side panels - without center stanchions - swinging via manual central locking and mechanically foldable with sideboard spring assistor) * Hydraulic tailgate, 500 mm high, functioning as hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load securing: * 1 x 7-tonne recessed and foldable lashing point in each corner * 4 x 3-tonne recessed and foldable lashing rings on each side ----Ramps: * 1 pair of aluminum drive-on ramps (10 t/pair with axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber-tired and tracked vehicles * 2 receiving compartments for aluminum drive-on ramps, recessed from behind into the chassis * Load securing according to EN 12642 XL ----Coupling height: * Laden approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Superstructure painted RAL 9010 pure white * Chassis, drawtube, rear supports, underrun protection hot-dip galvanized * Axles, air tank, support winch at the front * K80 coupling painted in black shade ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 6.500 kg, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2010, vzmetenje: jeklo, velikost pnevmatike: 235 / 75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Vehicle is being sold on behalf of the customer. Some wooden planks are damaged. Equipped with 17 pairs of lashing rings. Loading height approx. 900 mm. -- Subject to typographical errors, mistakes, and modifications. Sample images used. More data available at: !, More Details: ! Lodpfx Aqsz Td H Depshn

Stanje: rabljeno, Leto izdelave: 2008, vrsta prenosa: drugo, prva registracija: 01/2008, barva: oranžna, prevoženi kilometri: 1.001 km, voznikova kabina: drugo, Lokacija vozila: Bovenden, dvižne rampe, 2-delne, hidravlične. Lodpfozzfcqex Aqpshn Dolžina rampe približno 4000 mm! Demontaža Mueller Mitteltal T 3 Kompakt 30,0! PODATKI O DODATNI OPREMI SO PODANI BREZ GARANCIJE, pridržana pravica do sprememb, vmesne prodaje in napak!

Stanje: rabljeno, lastna masa: 7.340 kg, največja dovoljena obremenitev: 22.660 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2012, dolžina tovornega prostora: 9.200 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, Dolžina nakladalne površine cca 9.200 mm, nakladalna višina cca 900 mm, 16 pritrdilnih obročev, vozilo se prodaja po naročilu, pridržujemo si pravico do tiskarskih napak, napak in sprememb, slike so vzorčne. Več podatkov na: !, More Details: ! Lhjdo Aawfrjpfx Aqpjn

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, Leto izdelave: 2026, RA-T 18,0: Obremenljiv spredaj in zadaj ----Zavore: * Wabco EBS-E (električni zavorni sistem) * Naprava za izredno sprostitev zavor za zračne zavore * Kolutne zavore 19,5" * Avtomatsko zavorjenje ob odpiranju prečnega nosilca ----Osi: * 2 x 10 t BPW široke osi ----Vzmetenje: * Zračno vzmetenje (avtomatsko spuščanje ob odklopu zavor) ----Elektrika / Osvetlitev: * Nadzor tlaka v pnevmatikah z možnostjo prikaza v tovornjaku prek signala EBS – brez vgradnje na strani tovornjaka * 15-polni priključek za elektriko * LED-osvetlitev s zaščitnim pokrovom * 2 LED-luči za vzvratno vožnjo (upravljanje prek vzvratne prestave) Ledpfx Aqol Tn U Repehn ----Povezovalna priprava: * Pnevmatsko spuščana povezovalna priprava, dolžine 1.800 mm, z 40 mm priključkom in nastavitvijo višine s pomočjo vzmetne povezave in zapornice ----Splošni dodatni deli: * Plastična orodjarna škatla 858 x 500 x 500 mm na desni strani * Shranjevalni predal za mreže za pritrditev tovora, izdelan iz pocinkane perforirane pločevine, dimenzije 1.000 x 500 x 500 mm, nameščen na strani * Zaprti plastični blatniki spredaj in zadaj * Zaprti stranski odbijač (RAL 9010 čista bela) kot reklamna površina * Zadnji podvozni odbijač * Plastični odbijač zadaj * Zložljiv A-znak * Opozorilni znak za nevarne snovi s priključeno mapo za spremljevalno dokumentacijo ter odsevna parkirna opozorilna tabla zadaj ----Površina za kontejner: * Dodatno obremenjevanje spredaj z možnostjo spuščanja tirnic zadaj in vtičnim nosilcem * Vdolbine za valje v območju vrtilnega obroča z mehansko nastavljivimi kotnimi omejitvami (2 položaja) spredaj levo in desno na tirnicah * Dolžina tirnic približno 6.830 mm * Pnevmatska 4-točkovna zapora * Za transport zunanjih valjnih kontejnerjev po standardu DIN 30722, del 1 – na voljo je certifikat za pritrditev tovora (Dekra). ----Višina nakladanja: * obremenjeno približno 1.130 mm ----Barvanje: * Podvozje in deli zapornice so pocinkani * Zračni rezervoar, osi, vrtilni obroč in povezovalna priprava so pobarvani v črni barvi ----Informacije: * --Dovoljena skupna masa 20.000 kg je tehnično možna-- * Novo vozilo brez prve registracije z garancijo proizvajalca * Napake in vmesna prodaja pridržane * Ilustrativne slike ----Dobavni rok: * Na voljo takoj iz Egestorfa

Stanje: novo, največja dovoljena obremenitev: 16.000 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2024, * KA-TA-RT 21.0 ML ----Braking System: * Without ABS/EBS, homologated for 40 km/h * Spring-loaded parking brake * Drum brakes ----Axles: * Gigant axles ----Suspension: * Tandem-balance unit with 100 mm wide parabolic springs ----Drawbar Eye / Drawbar: * Rigid, welded drawbar with low-maintenance ball joint for K80 ball coupling (adjustable by +77 mm / 33 mm via mounting plate) with elevated gallows for connection lines ----Electrics / Lighting: * 12 V 7 + 4-pin power supply cable * LED lighting system, 12 / 24 V with protective grilles * 2 LED work lights at the rear, switchable from the towing vehicle, no vehicle-side installation required ----General Attachments: * Landing gear at the front * Mechanical drop legs at the rear * Side marker lights with indicator control * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right-hand side * Hot-dip galvanized two-step access steps in front of the bulkhead on the left (FR) ----Chassis: * Chassis made from high-tensile fine-grained steel ----Tipper Body: * Steel pallet three-way tipper body with M-Strong side boards (fixed front wall, continuous sides without central stanchions, swinging via manual central locking, plus mechanically folding with board spring lifters) * Hydraulic tailgate, 500 mm high, engineered as a hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor ----Load Securing: * Each corner equipped with 1 x 7 t recessed folding lashing ring * Each side fitted with 4 x 3 t recessed folding lashing points ----Ramps: * 1 pair aluminum loading ramps (10 t/pair for axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber and tracked vehicles * 2 recessed storage compartments for aluminum ramps in the rear of the chassis * Load securing compliant with EN 12642 XL Lhjdsr Dpz Hopfx Aqpsn ----Coupling Height: * Loaded approx. 530 mm & unladen approx. 590 mm ----Paintwork: * Bodywork painted in RAL 9010 pure white * Chassis, drawbar, rear support legs, underrun protection hot-dip galvanized * Axles, air tanks, landing gear (front) * K80 coupling painted in black ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex works Egestorf

Stanje: rabljeno, konfiguracija osi: 3 osi, vzmetenje: parabolično listje (vzmet), velikost pnevmatike: 235-75R17.5, Leto izdelave: 2010, 3-osni nizek priklopnik, dostopen od zadaj. Dovoljena skupna masa 30.000 kg, nosilnost 22.700 kg. Nakladalna površina 8.900 mm (7.000 + 1.900) x 2.550 mm, opozorilni paket za prekomerno širino, 12 pritrdilnih ušes ter 8 žepov za stebričke z možnostjo istočasnega pritrjevanja, 6 orodnih zabojev. Dvodelne hidravlične rampe cca. 2.100+2.000 x 800 mm z gumijasto oblogo, hidravlično zadnjo podporo. BPW osi, EBS, parabolično vzmetenje z izravnalno enoto, pnevmatike 235-75 R 17.5. Pokrivljena vlečna roka, premična vlečna kljuka 40+50 mm. 2-cevni zračni (duomatik) in 2-cevni hidravlični priključek, 24 voltov. Višina nakladanja praznega vozila cca. 910 mm. Barva oranžna. Tehnični pregled veljaven do 03-2027. = Dodatne informacije = Dimenzije pnevmatik: 235-75R17.5 Vzmetenje: parabolično vzmetenje Lhodpsy Evvljfx Aqpsn Lastna masa: 7.300 kg Nosilnost: 22.700 kg Skupna dovoljena masa: 30.000 kg Država proizvodnje: DE Za več informacij se obrnite na Jan-Marc Schwickert.

Stanje: rabljeno, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2010, naslednji pregled (TÜV): 07/2025, vzmetenje: zrak, velikost pnevmatike: 235/75R17.5, barva: rumena, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, turntable trailer, air suspension, ABS (anti-lock braking system), container locking mechanism, underrun protection, side aluminum side guard, twin tires. Body: 2-axle outer roller trailer for roll-off containers from 5.5 m to 7 m or 2x 10 m³ skip containers, BPW axles, drum brakes, pneumatic locking, pneumatic lowering drawbar. Lhodexgilmopfx Aqpjn ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-ER 19.0: ----Brake System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Flange Eye: * Drawbar with 50 mm flange eye and height adjustment of 110 mm by offset plate ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * LED tail lights 12 / 24 Volt ----General Attachments: * Jost landing gear, front * External folding supports, rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Reinforcement package for drilling rig transport on chassis * 50 mm softwood flooring, clamped * Preparation in front of front wall for subsequent installation of container locks * Bolted front wall, smooth sheet * Split side walls, steel sheet, trapezoidal profile—foldable with central folding stakes * Steel rear wall, sliding between ramps—holder inside front wall when not in use * Bolt-on rear stakes ----Load Securing: * Perforated outer frame, approx. 45 degrees bent, with 2 t lashing capacity every 480 mm * Option to install 3 t fall-arrest lashing rings every 600 mm * Load securing package: Each front and rear corner 1 x 10 t UVV lashing ring, each side 2 x 8 t UVV retractable lashing rings in outer frame; in front and end crossmember various bores for 1.2 t lashing options ----Ramps: Ledpjmi Tcqefx Aqpehn * One-piece sliding ramps 12 t / pair, approx. 2,750 x 620 mm * Rear approach slope approx. 860 mm ----Loading Height: * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm ----Tires / Wheelbase: * Wheelbase: 1,810 mm * Tires: 235/75 R17.5 ----Paintwork: * Chassis, drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * ---Axles, air reservoirs, flange eye, and landing gear painted black--- * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release system for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lowering device including RTR function * First axle liftable * Last axle is self-steering trailing axle with electro-pneumatic steering lock via reverse gear PIN (Steering lock for trailing axle activated from the tractor for maneuvering purposes—no truck-side installation required—wired to PIN 10 in the 15-pin connector, only for maneuvering and not for use on public roads) * SmartBoard control unit as infotool with pressure sensors for displaying total axle load * Tire pressure monitoring with readout in the truck via EBS signal, no truck-side installation required * Fixed center drawbar with 50 mm flange drawbar eye (loaded 900 mm, mm height adjustment at the head plate) * Mechanical landing gear at the front, mechanical swivel supports at the rear chassis * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the drive-on slope * Folding rear stanchions * Steel rear wall slotted in before rear stanchions * Mechanically adjustable warning panel kit front and rear * Toolboxes made of galvanized steel sheet—black powder-coated—approx. 650 x 300 x 600 mm, right side * 15-pin power connector * LED tail lights * Removable LED rotating beacon incl. bracket and installation * 2 x LED reversing lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir wooden floor * 400 mm steel front wall slotted in * Perforated outer frame approx. 45° angled with provisions for mounting 3 t folding lashing rings * In each corner: 1 x 10 t lashing ring, plus 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes for 1.2 t lashing points in front and rear crossmembers * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways Lsdpfx Aqer Dpzxjpshn * 4-circuit hydraulic control block for potential retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, mechanical rear supports, and loading ramps hot-dip galvanized * Axles, air tanks, flange drawbar eye, and front landing gear painted in black * Hydraulic flow divider in the trailer (for hydraulic pump output in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Subject to error and prior sale * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.970 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, KA-TA-R 14.4 - LKW tandem trostrani kiper - Nosivost serijski cca: 11.050 kg - Povećanje ukupne dozvoljene mase na 14,4 t kod guma 285/70R19.5 - Unutrašnje dimenzije: 5.000 x 2.420 x 500 mm - Visina poda pod opterećenjem: 1.040 mm Ledpfx Aoxmwiyjqpjhn - 1 šasija sa zaštitom od podletanja, vruće pocinkovana - Lakiranje: osovine sa oprugama, vazdušni rezervoari itd. u crnoj boji - 3 para upuštenih i preklopnih veznih kuka u čeličnom podu, LC 3.000 daN - ABS 2S/2M, 24 volti - 2 podizne opruge za čelične bočne stranice visine 500 mm - 1 centralno zaključavanje levo i desno, njihajuće kod nepreklopnih bočnih stranica Dodatna oprema: 1 par UVV veznih prstenova upuštenih u čelični pod, umesto na čelični pod 1 čelični pod od Hardoxa 450, debljine 4 mm Podešavanje visine vučne ruke preko ugaonog prenosa sa ručnim pogonom umesto serijskog 1 par alu rampi bez ivica (8,0 t/par), 3.500 x 400 x 105 mm pogodno za pneumaticima i guseničarima Kutija za alat

Stanje: novo, največja dovoljena obremenitev: 20.500 kg, skupna masa: 27.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TR 27.0 Flatbed: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower system featuring RTR function * 1st axle liftable * Rear axle as trailing steering axle with electro-pneumatic steering lock via reverse gear PIN (trailing axle lock for maneuvering purposes—no truck-side installation—assigned to PIN 10 in the 15-pin connector, for shunting purposes only, not for use on public roads) * SmartBoard control box as an info tool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * Fixed central drawbar with 50 mm flange towing eye (loaded 900 mm, mm height adjustment at head plate) Lsdor Dpz Aspfx Aqpshn * Mechanical support windlass at the front, mechanical swing supports at the rear of the chassis * Mechanically adjustable warning sign package at the front and rear * Toolboxes made of galvanized sheet steel—black powder-coated—approx. 650 x 300 x 600 mm on the right side * Hydraulic flow divider * Continuous side walls (without central stanchion) up to the access ramp * Folding rear stanchions * Steel rear wall inserted in front of the rear stanchions * 15-pin electrical connector * LED tail lights * Removable LED beacon with holder and installation * 2 x LED reversing lamps at the rear of the vehicle (controlled by reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir timber floor * 400 mm steel front wall plug-in * Perforated outer frame approx. 45-degree angled with provisions for 3 t folding lashing brackets * In each corner, 1 x 10 t lashing ring, plus 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes in the front and end cross-members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically laterally adjustable * 4-way hydraulic control block for possible retrofit of hydraulic ramp lateral adjustment * Chassis, drawbar, front wall, mechanical rear supports, loading ramps, and tailgate hot-dip galvanized * Axles, air tanks, flange towing eye, and front support windlass painted in black tone * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck of more than 40 ltr up to 120 ltr/min) * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.850 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 "Masterline" Lhsdpsl Thymsfx Aqpjn ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem load equalization unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (approx. 300 mm adjustment range) with 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, on the right-hand side * Bolted underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS tire pressure monitoring system ----Tipper Body: * Net hooks at sides and rear in the central locking compartments, as well as 2 units on the front wall * Steel palletized 3-way tipper body (continuous side walls—without central stanchions—foldable with board spring-lifter) * Rear stanchions bolted * Combination steel double-wing rear doors, asymmetrically divided, can be opened and locked at 270°, not foldable—with additional swinging frame for automatic rear tailgate opening during tipping process; locking via galvanized locking rods and central locking * Deactivation function for automatic rear tailgate operation when tipping backwards with open wing door * 4 mm steel chequer plate floor * Rear mounting rail for loading ramps ----Load Securing: * One 5 t lashing ring per corner * Four 3 t lashing rings each side, recessed into the outer frame ----Ramps: * 1 pair aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable rear storage compartment beneath the loading area, integrated into the chassis ----Paintwork: * Drawbar, front wall, tipper body, rear stanchions, underrun protection, and mechanical supports hot-dip galvanized * Side walls and tailgate painted in RAL 9010 pure white * Side wall painting in other RAL color shades available for an additional charge * Axles, springs, flange eye, air tanks, and landing gear painted in black ----Information: * Reinforced body with cargo securing certificate according to EN 12642 XL * New vehicle, without initial registration, with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex works Egestorf on the A7 Motorway

Stanje: novo, največja dovoljena obremenitev: 8.850 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 "Masterline" ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensating unit ----Drawbar / Flange Eye: * Approx. 300 mm height-adjustable drawbar with 40 mm flange eye ----General Fittings: * Jost mechanical landing gear at front * Rear: 2 mechanical, hot-dip galvanized drop-down support legs * Plastic toolbox approx. 750 x 350 x 300 mm, fitted on right side * Bolted underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS tire pressure monitoring system ----Tipping Platform: Lhjdpfx Ajl Thyxsqpen * Mesh hooks on the sides and rear in the central locking fixtures, plus 2 at the front wall * Steel pallet, 3-way tipping body (continuous sidewalls – without center stanchions – foldable with drop side spring assistance) * Rear stanchions bolted * Combination steel double rear doors, asymmetrically split, can be swung open and locked at 270°, not foldable – with additional pendulum frame for automatic tailgate opening during tipping operation; locking via galvanized swing bolt locking and central locking system * Deactivation function for automatic rear wall opening when tipping backwards with open door * 4 mm steel floor plate * Rear ramp carrier rail for drive-on ramps ----Load Securing: * 1 x 5 t lashing point in each corner * 4 x 3 t recessed lashing rings per side, fitted in the outer frame ----Ramps: * 1 pair of aluminum drive-on ramps approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for vehicles on rubber tires & tracks * Lockable storage compartment for ramps under the loading platform, integrated into the chassis ----Paint Finish: * Drawbar, front wall, tipping platform, rear stanchions, underrun protection, and mechanical support legs hot-dip galvanized * Sidewalls and tailgate painted RAL 9010 pure white * Sidewall painting in any RAL color available at extra charge * Axles, springs, flange eye, air tank, and landing gear painted in a black tone ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available ex-works Egestorf on A7

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ---- Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ---- Axles: * 2 x 11 t Gigant axles ---- Suspension: * Air suspension with manual lowering at the rear ---- Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ---- Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * 15-pin power connector * LED tail lights ---- General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm, fitted on the right side (black powder-coated) * Side underride protection * Plastic quarter mudguards ---- Low Loader Platform: * Reinforcement package for drilling rig transport on the chassis – loading height +20 mm * 50 mm softwood floor in clamped design * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal-profiled steel sheet, foldable with board wall spring-assisted lifter * Steel rear wall, can be inserted between the ramps – storage bracket in front of the bulkhead when not in use * Rear stakes bolted ---- Load Securing: Lhjdpfx Ajpk D Nceqpon * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * Each front and rear corner with 1 x 10 t lashing ring; various holes in the headboard and end cross member for 1.2 t lashing options ---- Ramps: * One-piece mechanical steel grating ramps with spring assistance for one-man operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear access slope approx. 860 mm ---- Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ---- Painting: * Chassis, drawbar, headboard, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing leg painted in black * Side boards painted in RAL 9010 pure white * Side walls can be painted in any RAL color for a surcharge ---- Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ---- Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.900 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14,4 Platforma: ----Zavore: * EBS (električni zavorni sistem) * Naprava za izpust zavor v primeru okvare za cilindrične zavorne zavore * Bobnaste zavore ----Osi: * 2 x 5,5 t BPW osi ----Vzmetenje: * Zračno vzmetenje z dvigom in spuščanjem ----Vlečna palica / prirobnična vlečna palica: * Vlečna palica, nastavljiva po višini za 300 mm * Vlečna palica, skrajšana za pribl. 200 mm na pribl. 1.800 mm (s tem je B-razdalja pribl. 8.080 mm) * 40 mm prirobnična vlečna palica ---- Elektrika / osvetlitev: * 15-polni električni vtič * LED-osvetlitvena naprava 12 / 24 V * 2 LED-luči za vzvratno vožnjo, dodatno nameščeni zadaj (vklopljene preko vzvratne prestave) * 1 LED-svetilka za 360-stopinjsko osvetlitev (odstranljiva, vključno z nosilcem) zadaj * Sistem za nadzor tlaka v pnevmatikah (RDÜ) ----Splošni dodatni deli: * Mehansko nastavljivi opozorilni znaki 3 m na sprednji in zadnji strani * Podporni vijačni mehanizem na sprednji strani * Zunanja zložljiva opora na zadnji strani * Plastične škatle za orodje, pribl. 750 x 350 x 300 mm, nameščene na levi in desni strani * Stranska zaščita * Zaščita pred podvozjem * Plastični četrtorni blatičniki ----Tovoršče: * 400 mm visoka vijačeno pritrjena sprednja stena * 50 mm debela stenska plošča iz iglavca * 2 para naprav za zaklepanje kontejnerjev (raztegljiva na 3 m zunanje širine kontejnerja) in blokirna, mera za zaklepanje v potegnjenem stanju po ISO - DIN 15190 = 2.259 mm. Raztegnjena mera za zaklepanje kontejnerjev = 2.819 mm (ta mera ni po DIN) pri absolutni zunanjem širini 3.000 mm ----Pripomočki za pritrditev tovora: Lhsdpfxoy U A Efs Aqpjn * Zunanji okvir z luknjami, pod kotom pribl. 45 stopinj, z 2 t vlečne sile na vsakih 480 mm * Možna je vgradnja 3 t pritrdilnih elementov na vsakih 600 mm - na vsaki strani 5 x 3 t pritrdilnih elementov UVV- * V kotiščih na sprednji in zadnji strani po 1 x 6,3 t pritrdilni element (na sprednji strani neposredno za napravami za zaklepanje kontejnerjev v stenski plošči, na zadnji strani pa v zadnji nosilni palici) * V sprednji in zadnji nosilni palici različne luknje za pritrditev z 1,2 t ----Rampe: * 1 par aluminijastih rampeh za natovarjanje pribl. 3.310 x 410 mm (nosilnost 8 t / par) za vozila z gumijastimi in goseničnimi pogoni * Na zadnji strani, pod tovorščem, v podvozju vgrajen prostor za shranjevanje ----Barvanje: * ---Podvozje, vlečna palica, sprednja stena, zaščita pred podvozjem in zadnje opore, prevlečene s pocinkom--- * Osi, zračni rezervoar, podporni vijačni mehanizem na sprednji strani in prirobnična vlečna palica, prevlečene s črno barvo ----Informacije: * Novo vozilo z garancijo proizvajalca * Napake in vmesna prodaja pridržane * Ilustrativne slike ----Dobavni rok: * Dostavljivo približno od 50. tedna 2026

Stanje: novo, največja dovoljena obremenitev: 8.900 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14,4 platforma: ----Zavore: * EBS (elektronski zavorni sistem) * Naprava za izpust zavor za zračni akumulator * Bobnaste zavore ----Osi: Lhedpfx Aoy U A Eljqpjn * 2 x 5,5 tone, osi BPW ----Vzmetenje: * Zračno vzmetenje z dvigalom in spuščanjem ----Vlečna prikolica / priključna prikolica: * Vlečna prikolica, višina nastavljiva za 300 mm * Vlečna prikolica, skrajšana za približno 200 mm na približno 1.800 mm (s tem je B-dimenzija približno 8.080 mm) * 40 mm priključna prikolica ---- Elektrika / osvetlitev: * 15-polni vtič za električno povezavo * LED-osvetlitev 12 / 24 V * 2 LED-luči za vzvratno vožnjo, dodatno nameščeni zadaj (upravljane z vzvratno prestavo) * 1 LED-rotacijska luč (snemljiva, vključno z nosilcem), zadaj * Sistem za nadzor tlaka v pnevmatikah (RDÜ) ----Splošni dodatni deli: * Mehansko nastavljive opozorilne table 3 m, spredaj in zadaj * Podpira spredaj * Zunanja zložljiva podpora zadaj * Plastične škatle za orodje, približno 750 x 350 x 300 mm, nameščene na levi in desni strani * Stranska zaščita * Podvozna zaščita * Plastični blatniki ----Nosilna plošča: * 400 mm visoka vijakom pritrjena čelna stena * 50 mm debelo dno iz iglavca * 2 para zaklepov za kontejnerje (raztegljivi do 3 m širine kontejnerja) in zaklenljivi, mera zaklepanja v spuščenem položaju po ISO - DIN 15190 = 2.259 mm. Zaklepi za kontejnerje v raztegnjenem položaju = 2.819 mm (ta mera ni po DIN), pri absolutni zunanji širini 3.000 mm ----Varnost tovorja: * Perforiran zunanji okvir, upognjen pod kotom približno 45 stopinj, z nosilnostjo 2 toni na vsakih 480 mm * Možnost vgradnje 3-tonskih pritrdilnih elementov na vsakih 600 mm - na vsaki strani 5 x 3-tonske pritrdilne elemente * V kotih spredaj in zadaj po 1 pritrdilni točki s 6,3 ton nosilnosti (spredaj neposredno za zaklepi za kontejnerje v lesenem dnu in zadaj v zaključni nosilni palici) * V čelni in zaključni nosilni palici različne luknje za možnost pritrjevanja z nosilnostjo 1,2 tone ----Rampe: * 1 par aluminijastih ramp za vstavljanje, približno 3.310 x 410 mm (nosilnost 8 ton / par), primerni za vozila s gumami in gosenicami * Shranjevalni prostor zadaj, pod nosilno ploščo v šasiji ----Barvanje: * ---Šasija, vlečna prikolica, čelna stena, podvozna zaščita in zadnje podpore, pocinkane--- * Osi, zračni rezervoar, sprednja podpora in priključna prikolica, barvane v črni barvi ----Informacije: * Novo vozilo s tovarniško garancijo * Pridržane napake in možnost prodaje * Ilustrativne slike ----Dobavni rok: * dobavljivo od približno 50. tedna 2026

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T3 Profil 30,0 ----Zavore: * EBS-E (elektronski zavorni sistem) * Sistem za odklepanje zavor v primeru izrednih razmer za cilindr vzmetne zavorne enote * Bobnaste zavore ----Osi: * 3 x 11 ton BPW Eco osi ----Vzmetenje: * Zračno vzmetenje s sistemom za dvigovanje in spuščanje ----Vlečna prikolica: Vlečna prikolica s 40 mm vlečnim ujčkom in nastavitvijo višine prek vzmetne palice in napenjalnega mehanizma ----Elektrika / Osvetlitev: * SmartBoard kot informacijsko orodje na prikolici z tlačnimi senzorji za prikaz tlaka za skupni prikaz obremenitve osi na posamezni skupini osi * 15-polni priključni vtič Lhedpfx Aqjtplv Nepjn * LED-osvetlitev 12 / 24 V * LED-okrogla luč (snemljiva) zadaj * Stranske markerne luči s funkcijo smerokaza * Sistem za nadzor tlaka v pnevmatikah z možnostjo prikaza v tovornjaku prek signala EBS (brez vgradnje na strani tovornjaka) ----Splošni dodatni deli: * stranski zaščitni element ob trku * mehansko nastavljivi paketi opozorilnih tabel spredaj in zadaj * sprednji pokrov blatnika iz plastike in zadnji, ravno pocinkan pokrov, oba s pršilno zaščito * pokrov (vroče pocinkan) za orodjno omarico v platformi podvozja * Orodjna omarica iz pocinkane jeklene pločevine, približno 650 x 300 x 600 mm (črna, prašno lakirana), na desni strani ----Površina nizkega priklopnika: * na obeh straneh po 4 nosilnih žepov s hkratno možnost pritrditve tovora do 2 toni * gumijasta prevleka na zložljivih rampah ter na nagibni površini na levi in desni strani (približno 860 mm dolga) * gumijasta prevleka na vzdolžnih nosilcih od čelnega do zadnjega nosilca * trden leseni pod področjem vožnje na platformi nizkega priklopnika * nosilci za les pod nosilno površino v vzdolžni smeri * opora valjev pred čelnim nosilcem, dvignjena, z 1 x 6,4 tone pritrdilnega ujčka na obeh straneh ----Paket za pritrditev tovora (La-Si-Paket, sestavljen iz): * 5 parov UVV pritrdilnih zank, vrtljivih in znižljivih, obremenljivih v vseh smereh in vgrajenih v zunanji okvir – v kotih 13,4 tone, sicer 10 ton * 6 parov mehanskih zložljivih podaljškov za 3 metre skupne širine (vendar ne na zadnji nagibni površini) ----Rampe: * Hidravlične zložljive rampe (približno 4.650 x 720 mm) s hidravlično razširjenim koncem in ventili za zadržanje tovora * hidravlični bočni premik ramp ----Hidravlika: * hidravlični razdelilnik pretoka v prikolici (pri hidravlični moči črpalke v tovornjaku nad 40 litrov do največ 140 litrov/min) * Hidravlični nadzorni blok, zaščiten pred brizganjem vode * Dvovodnična hidravlika ----Zadnja opora: * zadnja opora, hidravlična (eno stopenjski cilinder) ----Dimenzije nosilne površine: * Nosilna površina nad vrtljivim obročem: približno 1.960 x 2.520 mm * zadnja nosilna površina: približno 6.500 x 2.520 mm (vključno z 860 mm nagibno površino) * višina nakladanja, natovorjena, približno 890 mm +/- 20 mm, zračno vzmetenje ----Barvanje: * Podvozje, podvozje, opora valjev, zložljivi podaljški in rampe, vroče pocinkani. * Osi, vrtljivi obroč, vlečna prikolica, posoda za zrak itd., barvani v črni barvi ----Informacije: * Novo vozilo z garancijo proizvajalca * Napake in vmesna prodaja rezervirani ----Čas dobave: * takoj na voljo v Egestorfu