Müller-Mitteltal Tt 40 Profi, Feuerverzinkt nakup rabljenega (14.306)

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: Redsylfvgopfx Akbou * Vehicle available from approx. week 23/2026

Stanje: novo, največja dovoljena obremenitev: 10.750 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange drawbar eye ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power plug * LED lighting ----General Fittings: * Support winch at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right, outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: Rodpfxjv D Tcbo Akbou * 50 mm softwood flooring * Preparation before the bulkhead and rear slope for retrofitting container locks for the transport of 20" containers * Bolted bulkhead made of smooth sheet steel * Side walls made of trapezoidal-profiled steel, folding design, divided centrally * Steel rear wall, can be inserted between the ramp brackets, stowed inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Slotted outer frame, angled at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Optionally, installation of 3 t folding lashing rings every 600 mm * Each front and rear corner equipped with 1 x 6.3 t lashing point * Various holes for 1.2 t lashing options in the bulkhead and rear crossmember * Profifix lashing rail along the centerline for lashing options up to LC 3000 daN ----Ramps: * One-piece mechanical grid approach ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Rear approach slope approx. 860 mm chassis height ----Wheelbase: * Wheelbase 1,140 mm ----Paintwork: * Drawbar, bulkhead, rear panel, folding supports, and approach ramps hot-dip galvanized * Axles, springs, air tank, flange drawbar eye, and support winch painted in black * Side wall paint in a RAL color of your choice (special or metallic paints not available), can be changed up to approx. 6 weeks before completion ----Information: * Reinforced and certified construction according to EN 12642 XL including load securing certificate * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available from approx. week 30 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2-in-1: Suitable for swap containers (Abrollbehälter) and as low-loader trailer ----Braking System: * EBS electronic braking system * Emergency release facility for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10-ton axles ----Suspension: * Air suspension with lift and lower system and RTR valve ----Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: Rjdpfx Akel Tq Nmjbeu * Tire pressure monitoring system, display option in truck via EBS signal (no truck-side installation required) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Tool box, powder-coated steel, approx. 1,000 x 300 x 600 mm * Storage box for container net, galvanized sheet metal, 960 x 300 x 450/400 mm * Reflective contour tape on sides and rear * Side underrun protection * Plastic quarter mudguards with splash guards * Rear plastic buffer bumper * Foldable 'A' sign at the rear ----Loading Platform: * Main frame with raised outer frame to guide swap containers * Steel sheet floor with recesses for rollers in the bogie area * Container length possible from 5,500 to 7,000 mm * Pneumatic 4-point clamping lock and mechanical plug-in stops in the running channel at the front, securing certificate according to DIN 30722-1 * Weld bead as anti-slip covering in the inclined running area * Mechanical drop-down supports at the rear ----Load Securing: * 1 pair 10 t UVV lashing rings at the front wall carrier * 3 pairs 10 t UVV lashing rings on each side of the outer frame * Each side with 4 x 2 t cloverleaf lashing eyes * 4 x 8 t recessed lashing brackets in the outer frame ----Ramps: * 1 pair aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from rear) ----Paintwork: * Chassis, bogie, locking elements, rear drop-supports hot-dip galvanized * Drawbar, axles, and air tanks painted in a black shade ----Additional Info: * New vehicle, no initial registration, full manufacturer warranty * Subject to errors and prior sale * Sample images ----Delivery Time: * Available approx. from KW 43 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2 in 1 = for roll-off containers and as low-bed trailer ----Braking system: * EBS electronic braking system * Emergency release for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 ton axles ----Suspension: * Air suspension with lift and lowering system, including RTR valve ----Drawbar: * Drawbar, 2,000 mm long with 40 mm towing eye and height adjustment ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: Rodpfx Asl Tpc Aekbju * Tool box made from powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Storage box for container net made from galvanized sheet, 960 x 300 x 450/400 mm * Reflective contour marking tape on sides and rear * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumper buffers * Foldable rear A-board ----Loading area: * Main frame with raised outer rails to guide the roll-off containers * Steel floor plate with roller recesses in the bogie area * Container length of 5,500 - 7,000 mm possible * Pneumatic 4-way clamp lock, as well as mechanical plug-in stop angles at the front of the guide track, load securing certificate according to DIN 30722-1 * Weld bead as anti-slip coating in the ramp area * Mechanical drop-down supports at the rear ----Load securing: * 1 pair of 10 ton UVV lashing rings at the front on the bulkhead carrier * 3 pairs of 10 ton UVV lashing rings on the outer frame (side) * 4 pairs of 2 ton side lashing eyes with cloverleaf design on each side * 4 x 8 ton recessed lashing brackets in the outer frame ----Ramps: * 1 pair of aluminum access ramps (10.6 tons/pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Chassis, bogie, locking parts, rear drop-down supports hot-dip galvanized * Drawbar, axles, air tanks painted in black ----Information: * New vehicle without first registration, with full manufacturer's warranty * Subject to errors and prior sale * Sample images ----Delivery time: * Available from approx. week 43 / 2026

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Lifting middle axle ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumpers * Mechanical rear drop-down supports ----Container / Low-bed Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length of 5,500 - 7,000 mm possible * Pneumatic 4-point container clamp locking as well as mechanically plug-in front stop angles in the guide tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering of the skips, front 4 skip stops plug-in with pendulum stoppers ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and non-positive load securing of skips * 4 lashing rails in cloverleaf design (side) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp incline running area * 1 pair of aluminum approach ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1003 mm ----Payload: * Payload 18,900 kg Rodpfjtplv Tjx Akbeu ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without initial registration with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3 in 1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm towing eye and height adjustment device ----Electrical / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Tool box made of powder-coated sheet steel, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box for container nets, made of galvanized sheet, approx. 960 x 300 x 400 / 450 mm, right side * Plastic rear collision protection buffers * Mechanical drop-down supports at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, possible container length from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking as well as mechanically insertable stop angles at the front in the track, load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 removable skip stops for lateral centering of the skips, front 4 skip stops inserted with pendulum mount * Weld bead as anti-slip coating in the ramp area ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 lashing bars each, cloverleaf design (side) * 1 pair of 13.4 t UVV lashing rings to the front ----Ramps: * 1 pair of aluminum access ramps (10.6 t/pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 Rsdol Thwcspfx Akbsu * Permissible gross weight of 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3-in-1 = for roll-off containers, skip containers, and as a low-loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm drawbar eye with height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no installation required on the truck side) ----General Attachments: Rodpfxol Thv Re Akbeu * Toolbox made of powder-coated steel sheet, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box made of galvanized sheet metal for container nets, approx. 960 x 300 x 400/450 mm, right side * Plastic bumper buffer at rear * Mechanical drop-down supports at rear ----Load Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll containers * Steel floor with roller recesses in the bogie area * Possible to transport roll-off containers with a length of 5,500–7,000 mm * Pneumatic four-point clamp locking as well as mechanical locking angles at the front in the track, securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. volume of 10 m³ possible * Includes 8 removable tub stops for lateral centering of the tubs; front 4 stops plugged in with pivotable stop * Weld bead as anti-slip coating in the ramp area of the run-up incline ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements to securely fix the tubs * 4 lashing bars per side, cloverleaf design * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminium drive-on ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-wheeled and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight up to 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. calendar week 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.410 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, prostornina tovornega prostora: 11 m³, Leto izdelave: 2026, * KA-TA-R 18.0 ML * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring brake cylinders * Drum brakes * Tire pressure monitoring system with display capability in the truck dashboard via EBS signal (installation on the truck side not required) * 2 x 9 t Gigant axles * Air suspension with level control during tipping operation * Drawbar with 50 mm flange towing eye (adjustable by +77 mm and -33 mm using offset plate) * Jost landing gears at the front * Folding galvanized steel underrun protection for paver loading * Closed plastic single mudguards * Standing platform on the front wall * Manual sliding tarpaulin * 15-pin electrical connector * LED tail lights with galvanized protective cover * 2 LED reversing lights * Chassis made of fine-grained steel * Steel three-way tipper body (side walls with MM profile - continuous without side posts - swinging with manual central locking and drop-down left side wall with board spring lifter) * Tarpaulin similar to RAL 7038 agate grey with side tension by ratchet straps and elastic cords at the front and rear * Front wall platform made of grating with step at drawbar and hand grip on the front wall * Rear wall – made of HBW 400 steel – swinging with automatic 2-claw lock * 5 mm steel floor made of HBW 450 steel Rsdpfxsxl Nkge Akbsu * 4 x 3 t recessed and foldable lashing rings per side – integrated into steel floor * Reinforced and certified body according to EN 12642 XL including load securing certificate up to 19 t * Side wall paintwork in your desired RAL color (no special or metallic paintwork) – changeable up to approx. 6 weeks before completion * Axles, air tanks, landing gears, flange towing eye painted in black tone * Chassis, underrun guard and drawbar hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Available from approx. week 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axles: * 3 x 11 t Gigant axles * Center axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Tool box made of powder-coated sheet steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized sheet steel (W: 960 mm x H: 300 x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with splash guards * Plastic rear impact protection buffer Rodpfxspk D Iis Akbeu * Mechanical rear support legs ----Container / Low Loader Deck: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll containers * Steel sheet floor with roller recesses in the bogie area * Suitable for roll-off container transport with container lengths from 5,500 to 7,000 mm * Pneumatic 4-point container clamp lock and mechanical plug-in end stops at the front of the tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Includes 8 repositionable skip stops for lateral centering, front 4 skip stops plugged in with swinging end stop ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 cloverleaf-style lashing bars on each side and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp run-up area * 1 pair of aluminum loading ramps (16 t/pair) 2,800 x 400 mm suitable for rubber-tyred and tracked vehicles (lockable storage compartment at the rear) ----Tires: * Tires: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on the sides & rear * Axles, turntable, drawbar, and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible total weight technically possible: 27,000 kg * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 13.830 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Leto izdelave: 2026, * KA-TA-R 18 ----Brakes: * EBS-E (electronic braking system with RSS) * Emergency release for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 9 t Gigant axles ----Suspension: * Air suspension with level control during tipping ----Electrics / Lighting: * Tire pressure monitoring system with display possibility in the truck dashboard via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting with galvanized protective cover * 2 LED reversing lights ----Drawbar eye / Drawbar: * Drawbar with 50 mm flange towing eye (adjustable by +77 mm and -33 mm using offset plate) ----General attachments: Rsdpfx Akex Ipbyobeu * Landing leg at the front * Foldable galvanized steel underrun guard for paver feeding * Enclosed single plastic mudguards * Front wall platform made of grating with step on drawbar and handholds on the front wall ----Chassis: * Chassis made of fine-grain steel ----Tipper body: * Steel 3-way tipper body with continuous asymmetrical aluminum side walls – without center stanchion – pendulum-mounted with manual central locking, left side foldable with side board spring lifter * Tailgate – made from HBW 400 steel – pendulum-mounted with automatic 2-claw lock * 5 mm steel floor made from HBW 450 steel ----Load securing: * 4 x 3 t lashing rings per side – recessed and foldable – integrated into the steel floor ----Roll tarp: * Roll tarp – agate grey, similar to RAL 7038 * Tarpaulin tensioning using ratchet tensioners on the sides and tensioning rubber at the front and rear ----Painting: * Chassis, underrun guard, and drawbar hot-dip galvanized * Axles, air tanks, landing leg, and flange towing eye painted in a shade of black * Side wall painting according to RAL color of choice (excluding special or metallic paints); color can be changed up to approx. 6 weeks before completion ----Info: * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale * Sample images (vehicle images may vary due to special equipment) ----Delivery time: * Vehicle available from week 42/2026

Stanje: novo, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * KA-TA-R 11.9 Masterline ----Brakes: * Wabco EBS * Emergency release device for spring brake chambers * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Towing Eye: * Height-adjustable drawbar (approx. 300 mm) with 40 mm flange towing eye ----Electrics / Lighting: * RDÜ tire pressure monitoring system * Multivoltage * 15-pin power connector * 12V 13-pin auxiliary cable * Extended connection cables for forestry and agricultural towing vehicles * LED tail lights ----General Attachments: * Mechanical landing gear at front * Rear: 2 mechanical foldable supports * Plastic toolbox, right side * 2-step access step, front left (in direction of travel) * Bolt-on underrun protection * Plastic quarter mudguards ----Tipping Platform: * Mesh hooks on the sides and rear in the central locking mounts, plus 2 on the front wall * Steel pallet, 3-way tipper body (continuous side walls - without central stanchions - foldable with side wall spring assist, tailgate foldable and swinging via manual central locking) * 4 mm steel plate floor Redpfx Aksq Euagebeu * Rear mounting rail for loading ramps ----Load Securing: * 1 x 5 t lashing ring in each corner * Plus 4 x 3 t recessed lashing points per side in the outer frame ----Ramps: * 1 pair aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading platform, integrated in the chassis ----Tyres: * Tyres 385/55 R 19.5 ----Paintwork: * Chassis, drawbar, tipper body, front wall, foldable supports, and rear stanchions hot dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in a shade of black * Side boards painted in RAL color of your choice (excluding special or metallic paint); color can be changed up to approx. 6 weeks before completion ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer warranty * Subject to errors and prior sale * Sample images ----Delivery time: * Available from approx. calendar week 28 / 2026

Stanje: novo, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * KA-TA-R 11.9 Masterline ----Brakes: * Wabco EBS * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensation unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm, with 40 mm flange towing eye ----Electrics / Lighting: * RDÜ tyre pressure monitoring system * Multivoltage * 15-pin power connector * 12 V 13-pin supplementary cable * Extended connection cables for forestry and agricultural towing vehicles * LED tail lights ----General Attachments: * Mechanical support winch at the front * Two mechanical folding supports at the rear * Plastic toolbox mounted on the right side * Two-step access ladder, front left in direction of travel * Bolt-on underrun protection * Plastic quarter mudguards ----Tipper Body: * Mesh hooks on the sides and rear at the central locking bearings, plus 2 pieces at the front wall * Steel pallet—3-way tipper body (continuous side panels—no centre stanchions—fold-down with side panel spring assist, tailgate foldable and swinging via manual central locking) * 4 mm steel floor * Rear ramp mounting rail ----Load Securing: * 1 x 5 t lashing ring in each corner * 4 x 3 t recessed lashing rings per side in the outer frame ----Ramps: * 1 pair of aluminium ramps, approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for rubber-tyred and tracked vehicles Rjdpfxol Thw Ie Akbsu * Lockable storage compartment beneath the loading area integrated into the chassis at the rear ----Tyres: * Tyres 385/55 R 19.5 ----Paint: * Chassis, drawbar, tipper body, front wall, folding supports, and rear stanchions hot-dip galvanised * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Sideboard paintwork in preferred RAL colour shade (excluding special or metallic paints), changeable up to 6 weeks before completion ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Subject to prior sale and errors excepted * Sample images ----Delivery Time: * available from approx. week 28 / 2026

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem compensation unit * Height-adjustable drawbar, approx. 300 mm, with 40 mm flange towing ring * Jost mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted front right on the chassis * 15-pin electrical connector * LED tail lights 12/24 V * Bolt-on underrun guard * Plastic quarter mudguards * Net hooks located at the central locking bearing and 2 on the front wall Rodex Hm Rcjpfx Akbou * Chassis made of high-tensile steel * Steel three-way tipper body with reinforced "Strong" side walls (continuous upper side walls, reinforced with internal tube, no central stanchions, foldable with side wall spring lifter) * Bolt-on rear stanchions * Combination steel double-wing rear door, asymmetrical split, can swivel and be locked at 270°, not foldable, with additional pendulum frame for automatic tailgate opening when tipping, locking via galvanized rotary bolt lock at the rear and central locking. Deactivation function for automatic tailgate operation when reverse tipping with open door wing * 1 x 5 t lashing ring in each corner and 4 x 3 t lashing points recessed into the outer frame on each side * 4 mm high-tensile steel floor plate * Rear mounting rail for loading ramps * Reinforced body with load securing certificate * 1 pair of aluminum loading ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired & tracked vehicles * Lockable rear storage compartment recessed below the loading area in the chassis for the ramps * Drawbar, underrun guard, rear stanchion, and rear folding supports hot-dip galvanized * Axles, springs, air tanks, and support winch painted in a black finish * Tires: 358/55 R 19.5 * Side wall coating in a RAL color of your choice (no custom or metallic finishes). Color can be changed up to approx. 6 weeks before completion. * Subject to errors and prior sale. * Available immediately from week 29/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display capability in the truck via EBS signal – no truck-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic leaf springs with tandem compensating aggregate * Drawbar height adjustable by approx. 300 mm with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical foldable supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted front-right on chassis * 15-pin power connector * LED rear lights 12/24 V * Bolt-on side underrun protection * Plastic quarter mudguards * Tie-down hooks located at central locking mounts, plus 2 on the front wall * Chassis made of fine grain steel * Steel platform – 3-way tipper body with reinforced strong side walls (continuous upper side walls with internal tube reinforcement – without intermediate posts, side walls foldable with drop side spring assist) * Rear corner posts bolted * Combination steel wing-door rear wall – dual-wing asymmetrical, can be swung and locked at 270°, not foldable, with additional swinging frame for automatic rear wall opening during tipping operation, locking via galvanised turning rod lock at the rear and central locking, deactivation function for automatic rear wall operation when tipping backwards with open door * Four 5 t lashing points in the corners, and four 3 t lashing rings recessed in the outer frame on each side * 4 mm steel floor made of fine grain steel * Mounting rail at rear for loading ramps Rodpfox Hm Risx Akbou * Reinforced body with cargo lashing certificate * 1 pair of aluminium loading ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tyred & tracked vehicles * Lockable storage compartment at rear under load area recessed in chassis for the ramps * Drawbar, underrun protection, rear corner posts, and rear foldable supports hot-dip galvanized * Axles, springs, air tank and landing gear painted in black * Tyres: 358/55 R 19.5 * Drop sides painted in desired RAL color (no special or metallic finishes) – can be changed up to approx. 6 weeks before completion * Subject to errors and prior sale * Available immediately from calendar week 29/2026 * Example images

Stanje: novo, največja dovoljena obremenitev: 16.500 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Müller-Mitteltal ETÜ-TAR 21 Tandem - Low Loader | Drive-over Platform Trailer Ref. for enquiries: 11630 Vehicle available immediately from stock in Alsdorf New vehicle inc. COC * Gross weight: 21 t, Payload: 16.5 t, hot-dip galvanized chassis * Platform version with 400 mm high front wall, ramp securing via ramp holding rods and diagonal bracing Rjdpfx Akoyvxg Usbju * Version with gross weight 21 t, reinforced frame and axles, axle spacing 1,810 mm * Floor height approx. 910 mm loaded / approx. 940 mm unloaded * 7 m loading area with 400 mm high front wall * Extended ramps: 3 m one-piece hot-dip galvanized ramps with galvanized grating * Ramp lift with vertically standing, adjustable springs for easy single-person operation * Load securing package: * 4 UVV folding lashing brackets (LC 8,000 daN) mounted in the existing hole pattern in the 45° outer frame, positioned approx. 1 m from front/rear crossmember * 10 UVV retractable lashing brackets (LC 3,000 daN) recessed in the existing hole pattern in the outer frame * 2 UVV lashing rings each at front and rear, recessed in crossmember, LC 10,000 daN * Additional lashing options via holes (Ø 50 mm, LC 1,200 daN) in the front and end crossmember * Preparation for retrofitting container locks (container locks available at extra cost) * Softwood floor, 50 mm thick * Air suspension, Gigant axles incl. EBS 2S/2M, raising and lowering * 235/75R 17.5 (twin tyres, 8x) with tyre pressure monitoring sensor * Plastic toolbox in front of the front wall, right-hand side in direction of travel * LED lighting system * 7-pin socket at rear, prepared for overlength lighting with tail light (58 R) and ground * 2 LED reversing lights at rear * Flashing side marker lights * Oversize warning panel * 1 removable all-round LED beacon incl. bracket and installation * Folding supports at rear, front support leg with geared winding mechanism ---- Lease purchase example from our partner MMV Leasing: €665/month net for 60 months term with no down payment and €0 final instalment Other terms with/without down payment/final value possible! We are Müller-Mitteltal authorised dealer ----* Our business hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 * Outside business hours available by appointment * We speak German, English, Russian, Polish, French * WhatsApp

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring-loaded brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange towing eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General Attachments: * Jost landing gear at front * Externally mounted, hot-dip galvanized folding support legs at rear * Plastic toolbox, mounted front right exterior on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of bulkhead for retrofitting container locks * Bolt-on smooth sheet steel bulkhead * Side walls made of trapezoidal-profiled steel sheet, foldable with drop-side spring assist * Insertable steel rear wall between ramps – storage bracket for unused rear wall inside in front of bulkhead * Bolt-on rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option to install 3 t drop lashing rings every 600 mm * 1 x 6.3 t lashing ring in each corner at front and rear * Various holes in the front and rear crossmember for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps, spring-assisted for single operator use, approx. 2,750 x 600 mm (retractable to 20 mm) * Rear ramp approach slope approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, ramps and rear wall * Drop side color in RAL 9010 pure white * Side wall paintwork in any RAL color available at extra charge ----Information: * --Reinforced and certified superstructure according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer’s warranty * Errors and prior sale excepted Rjdpfexglibex Akbeu ----Delivery Time: * Available from approx. CW 27/2026

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Drawbar Eye: * Height-adjustable drawbar by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * TPMS (tire pressure monitoring system) * LED lighting ----General attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right, mounted externally on the front wall * Side underrun protection * Plastic quarter mudguards ----Low-bed platform: * 50 mm softwood floor * Fittings in front of front wall for optional installation of container locks * Bolted smooth sheet metal front wall * Fold-down trapezoidal profile steel side panels with sideboard spring lifters * Steel rear wall, retractable between ramps—when not in use, bracket mounted inside in front of the front wall * Rear stanchions bolted ----Load securing: * Perforated external frame, ca. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * In each of the four corners at front and rear, one 6.3 t lashing ring * Various holes in the front and rear crossmember for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring mechanism for single-person operation, ca. 2,750 x 600 mm (can be collapsed to 20 mm) * Approach angle at the rear approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, front wall, loading ramps, and rear wall * Drop side color in RAL 9010 pure white * Painting of the side panels in a RAL color of your choice available at extra cost ----Information: Rodpexglh Refx Akbeu * Reinforced and certified body according to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. CW 27/2026

Stanje: rabljeno, lastna masa: 3.110 kg, največja dovoljena obremenitev: 9.490 kg, skupna masa: 12.600 kg, konfiguracija osi: 2 osi, prva registracija: 05/2016, naslednji pregled (TÜV): 02/2025, dolžina tovornega prostora: 4.550 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 600 mm, vzmetenje: jeklo, velikost pnevmatike: 285/70R19.5, barva: modra, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, steel body, 2 axles, turntable trailer, leaf suspension, ABS (anti-lock braking system), lashing eyes, storage box, pendulum flaps. Body: 2-axle 3-way tipper trailer, Gigant axles, drum brakes, hot-dip galvanized frame! Rodpfxswth Iis Akbsu Loading height approx. 1290 mm! ACCESSORIES INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors excepted!

Stanje: dober (rabljeno), konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dovoljena osna obremenitev (os 2): 10.000 kg, dovoljena osna obremenitev (os 3): 10.000 kg, prva registracija: 11/2015, skupna dolžina: 14.000 mm, skupna širina: 2.550 mm, skupna višina: 4.050 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 17.5, medosna razdalja: 1.300 mm, Leto izdelave: 2015, Oprema: ABS, = Additional options and accessories = - EBS (Electronic Braking System) - Rear air suspension = Remarks = - Müller Mitteltal 3-axle low-loader - 3 × 10,000 kg axles - Fifth wheel load: 11,000 kg - Loading platform dimensions: Length 930 cm × Width 252 cm - Loading height: 98 cm - Dimensions of the covered neck: Length 500 cm × Width 264 cm - Neck loading height: 144 cm - Sliding curtain left and right - Dimensions of the hydraulic access ramp: - Section 1: 270 × 235 cm - Section 2: 180 × 235 cm - Lashing points - 2 storage boxes Well-maintained and robust low-loader, ideally suited for the transport of machines, forklifts, and work platforms, among others! = Further information = Axle configuration Tyre size: 235/75 17.5 Suspension: Air suspension Rear axle 1: Twin tyres; Max. axle load: 10,000 kg; Tyre tread left inner: 50%; Tyre tread left outer: 50%; Tyre tread right inner: 50%; Tyre tread right outer: 50% Rear axle 2: Twin tyres; Max. axle load: 10,000 kg; Tyre tread left inner: 50%; Tyre tread left outer: 50%; Tyre tread right inner: 50%; Tyre tread right outer: 50% Rear axle 3: Twin tyres; Max. axle load: 10,000 kg; Steering; Tyre tread left inner: 30%; Tyre tread left outer: 30%; Tyre tread right inner: 30%; Tyre tread right outer: 30% Weights Unladen weight: 10,700 kg Payload: 25,300 kg GVW: 36,000 kg Condition Technical condition: good Redpfx Aey I Axxjkbou Optical condition: good Product safety Manufacturer: Clean Mat Trucks B.V. Wageningsestraat 17 6673DB ANDELST, NL

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Braking System: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering system, including RtR valve and manual lowering for loading operations Rodpfxovin T Se Akbou ----Drawbar / Flange Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flange drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V integrated in underrun protection ----General Attachments: * Landing gear at the front * Fold-out support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Plastic quarter mudguards ----Tipper Body: * Steel 3-way tipper body made of fine-grain steel with high M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall, smooth sheet steel * Hardwood pad for excavator bucket bolted to front wall * Continuous, folding drop sides without central stanchion, with sideboard spring assist and manual central locking system * Screwed-in rear stanchions * Combination steel swing doors, asymmetrical 2-leaf rear wall, can be swung and locked at 270°, not foldable, with additional swinging frame for automatic rear wall opening during tipping, locking via galvanized rotary bar lock and central locking system, deactivation function for automatic rear wall opening when tipping reverse with open swing doors * 4 mm steel floor plate * Two-step entry left front * Rear mounting rail for loading ramps ----Load Securing: * 1 x 7 t lashing ring in each corner * 4 x 3 t lashing rings recessed into the outer frame on each side ----Loading Ramps: * Integrally mounted ramp storage at the rear of the chassis * 1 pair of aluminum loading ramps (10 t / pair) approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, rear folding supports hot-dip galvanized * Sideboard paintwork in RAL custom color (with exceptions for special or metallic paintwork); can be changed up to approx. 6 weeks prior to delivery * Axles, air tanks, flange drawbar eye, front landing gear painted in black ----Information: * --Load securing certificate according to EN 12642 XL? * Subject to errors and prior sale ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brake: * EBS (Electronic Braking System) * Emergency release for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering device, including Ride-Through-Release (RtR) valve and manual lowering function for loading ----Drawbar / Flanged Drawbar Eye: * Drawbar with positive-locking height adjustment * 50 mm flanged drawbar eye ----Electrics / Lighting: * 15-pin 24 V connector * LED tail lights 12 / 24 V fitted in underrun protection ----General Attachments: * Support winch at front * Fold-away rear support legs on the outside * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipping Body: * Steel pallet – 3-way tipper body made of high-tensile fine grain steel with high M-Strong side panels and reinforced 180 bar tipping cylinder * Fixed front wall made of smooth sheet steel * Hardwood strip for excavator bucket screwed onto front wall * Continuous side panels – fold-down without center pillar, with sideboard spring-assist lifters and swinging function via manual central locking * Bolt-on rear stanchions * Combination steel swing doors at rear, 2-leaf, asymmetrically split, able to swing open 270° and lockable (not foldable), including additional swinging frame for automatic rear door opening when tipping; locking by galvanized rotating bar lock and central locking, deactivation function for automatic rear door opening when tipping backwards with opened swing doors * 4 mm steel floor plate * Two-step access on the left front * Rear ramp track for loading ramps ----Load Securing: * One 7 t lashing ring in each corner * Four 3 t lashing eyes recessed in the outer frame on each side ----Loading Ramps: * Recessed ramp compartment at rear of chassis * 1 pair aluminium loading ramps (10 t/pair), approx. 3,570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Paintwork: * Chassis, drawbar, rear stanchions, front wall, tipping platform, underrun protection, and rear supports hot-dip galvanized * Sideboards painted in any desired RAL colour (excluding special or metallic paints), can be changed up to approx. 6 weeks before completion * Axles, air tanks, flanged drawbar eye, and front support winch painted in black ----Info: Rjdpfx Aevin Ucjkbou * --Load securing certificate according to EN 12642 XL? * Errors and intermediate sale reserved ----Delivery Time: * Available from approx. CW 45 / 2026

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: * RDÜ (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube supports at the rear with base plate and safety locking pins for various support heights * Tow bar with 40 mm bolted towing eye (height-adjustable) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made from torsion-resistant square tubes and cross members * Closed steel mudguards with splash protection * Enclosed side underrun protection usable as advertising space * Plastic toolbox with floor insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum superstructure, clear width between drum arms 1,700 mm, with tension lock for securing the drum at the support arm ends and a central claw lock for securing the cable drum structure to the chassis * Motor-hydraulic drum drive with oil motor * Valves and movable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive Redpfx Aksu I Iqxobeu * Steel drum shaft 76 mm diameter with centering and rotatable ends * 1 pair of polyamide centering cones, stepwise offset * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Corrosion protection: hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: * TPMS tire pressure monitoring system * EBS brake system * Drum brakes * BPW axles Redpfxsu I Iqlj Akbeu * Parabolic springs * Support winch at the front * Spring-assisted square tube supports at the rear with base plate and safety locking pins for variable support heights * Drawbar with 40 mm screwed towing eye (height adjustable, mm) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed steel mudguards with splash protection * Closed side underride guard usable as advertising surface * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum frame, clear width between drum arms 1,700 mm - with clamp lock for securing the drum at the support arm ends and a central claw lock for securing the cable drum frame to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of polyamide centering cones, stepwise offset * Hydraulic power unit with diesel engine * Fuel tank and hand starter * 6.5 hp with gear pump (150 bar) * Finish: hot-dip galvanized * New vehicle with full manufacturer’s warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: * RDÜ Tire Pressure Monitoring System (TPMS) * EBS brake system * Drum brakes * BPW axle * Parabolic springs * Support winch at front * Spring-assisted square tube supports at rear with baseplate and safety lock pins for various support heights * Drawbar with 40 mm bolt-type towing eye (height-adjustable mm) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel mudguards with splash protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with base insert (horizontal installation) approx. 500 x 350 x 400 mm * Swivelling cable drum rack, clear width between drum arms 1,700 mm, with clamp lock for securing the drum at the support arm ends and locking the cable drum rack to the chassis via a centrally located claw lock Rsdju I Iqrjpfx Akbsu * Motor-hydraulic drum drive with hydraulic motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotating ends * 1 pair of polyamide centering cones, stepped * Hydraulic pump unit with Loncin petrol engine, including manual and electric starter * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * 2,690 kg unladen weight * Vehicle is hot-dip galvanized * New vehicle with full manufacturer warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: * RDÜ Tire Pressure Monitoring System * EBS brake system * Drum brakes * BPW axle * Parabolic springs * Front support winch * Rear spring-assisted square tube supports with base plate and safety locking pins for various support heights * Drawbar with 40 mm screw towing eye (height adjustable) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made from torsion-resistant square tube and cross beams * Enclosed steel mudguards with splash protection * Enclosed side underrun protection, usable as advertising space * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm * Swivel cable drum superstructure, clear width between drum arms 1,700 mm – with tension latch for drum securing at the arm ends and a central claw lock securing the superstructure to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of stepped centering cones made of polyamide * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) Rjdpfx Aksu I Iq Eobou * Finish: hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf * Sample pictures