Nizki nakladalnik

Fliegl DTL 300 Agrar

Stanje: novo, največja dovoljena obremenitev: 18.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 5.900 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 860 mm, skupna širina: 2.520 mm, Total weight: 24,000 kg / 30,000 kg Tare weight: 5,600 kg Payload: 18,400 kg / 24,400 kg Overall length: 10,290 mm Loading length: 5,900 mm incl. rear bevel Width: 2,520 mm Loading height: 860 mm Additional Information: plus freight/preparation from storage location 26639 Wiesmoor €1,280.00 / net Low loader trailer chassis Steel welded construction Turntable with heavy-duty ball race Foldable rear supports Wheel chocks with holder Full-width rear mud flaps 1 plastic toolbox Prepared for width extensions up to 3,000 mm (holes in the outer frame with covers, not in the rear bevel) Lashing eyes for low loader 1 pair of lashing cutouts embedded at the front in the longitudinal beam at the gooseneck, each for 10 t 7 pairs of lashing mushrooms recessed on top and on the sides of the outer frame, each for 10 t • 1x at the front on the gooseneck • 5x in the low-bed area • 1x in rear bevel 12 pairs of lashing holes in the outer frame, each for 5 t (for tensioning strap hooks) • 5x gooseneck, 6x low-bed, 1x rear bevel Drawbar turntable coupling Drawbar with certified 40 mm towing eye Drawbar height adjustment via spring Axles & Suspension Drum brake axles, manufacturer’s choice Laser aligned axles/chassis – reduces tyre and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker compensation) Wheels and Tyres 235/75 R 17.5" Manufacturer’s choice Steel twin rims, factory silver Brake System 2-line pneumatic braking system Spring-actuated parking brake 2 foolproof coupling heads at the front with connecting lines to the towing vehicle, lines extended by approx. 60 cm Without ABS, but with mechanical ALB; max. 60 km/h permit Electrics 12 Volt, multi-chamber lights, without side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marking lights at the rear 1 x 7-pin 12 Volt plug at the front with connection cable, extended by approx. 60 cm 1 LED beacon with holder, switched via parking light (removable light) Floor Gooseneck at the front with steel/tread plate covering Storage box recessed in overrun slope to gooseneck Then with 70 mm softwood floor, steel/tread plate covering in wheel arch area Rear bevel with 70 mm softwood floor Low-bed area incl. rear bevel: 5,900 mm Access ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wooden covering (tip area with steel/tread plate) Hydraulic via tractor PTO with throttle, control on left side in front area Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Operating Notes Ledpfx Aswm Uy Ejb Ujhr An exemption is required for axle loads of 10,000 kg; only indivisible loads allowed! The stated total weight is technically possible. Depending on the load, the total weight may not be achievable while observing the permissible axle, support, and kingpin loads. (Poor handling and tracking may result from incorrect load distribution.) Country of Registration / License plates Country of registration: Germany With DEKRA inspection and certificate for max. 60 km/h approval, towing vehicle agricultural/forestry (LoF) (Approval in Switzerland max. 40 km/h possible) Prepared for two-line license plate holder Without contour marking / reflective stripes as per ECE R 048 Paintwork Frame: RAL 6013 reed green "10-year anti-perforation warranty" Drawbar galvanized Access ramps hot-dip galvanized

Stanje: rabljeno, Leto izdelave: 1999, Payload: 19,990 kg Gross vehicle weight (GVW): 8,010 kg Front tire condition: 70% Rear tire condition: 70% Front tires: 245/70 R 17.5 Rear tires: 245/70 R 17.5 For further information, please contact PFEIFER GROUP. Ledpfx Aeutw I Nsb Ushr

Stanje: novo, največja dovoljena obremenitev: 23.340 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, NEW VEHICLE Fliegl 3-Axle Flatbed Low Loader DTL - S - 300 Agrar, chassis and frame hot-dip galvanized Gross weight: 24,000 kg / 30,000 kg Payload: 17,340 kg / 23,340 kg Unladen weight: 6,660 kg Overall length: 11,625 mm Platform length: 9,000 mm incl. 900 mm approach slope Loading height: 900 mm Large lashing package 40 mm drawbar Tyres: 235 / 75 R 17.5'' twin wheels without ABS, approval max. 60 km/h Electrical system 12 Volt, LED rotating beacon Ramps with spring lifts, ramp length 2,800 mm Vehicle from ongoing production – delivery lead time approx. 14 days. plus freight/preparation ex stock Wiesmoor €1,280.00 / net Towing vehicle LoF, agricultural or forestry registration Lhjdpfxellwhne Ab Usr Lease-purchase offer: term 48 months, residual value 40%, down payment only the VAT. Monthly rate: €599.00

Stanje: novo, največja dovoljena obremenitev: 18.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 5.900 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 860 mm, skupna širina: 2.520 mm, Total weight: 24,000kg / 30,000kg Curb weight: 5,600kg Payload: 18,400kg / 24,400kg Overall length: 10,290mm Loading length: 5,900mm incl. rear bevel Width: 2,520mm Loading height: 860mm Additional information: Plus pre-carriage / handling from storage location 26639 Wiesmoor: €1,280.00 net Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race bearing Folding rear support Wheel chocks with holder Rear mudflaps across full width 1 plastic toolbox Preparation for widening to 3,000 mm (holes in outer frame with covers, not in rear bevel) Lashing rings for low-bed trailer 1 pair of lashing openings in the front beam on the cranked section, each rated 10 t 7 pairs of lashing pins recessed in the top and side of the outer frame, each rated 10 t 1 x in front on the cranked section 5 x in the low-bed section 1 x in the rear bevel 12 pairs of lashing holes in the outer frame, each rated 5 t (for securing straps) 5 x cranked section, 6 x low-bed, 1 x rear bevel Drawbar coupling (for turntable trailer) Drawbar with tested 40 mm towing eye Height adjustment of drawbar by spring Axles & suspension: Drum brake axles, manufacturer’s choice Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushing and mechanical load equalization (rocker equalizer) Wheels and tires: 235 / 75 R 17.5” manufacturer’s choice Steel rims, dual arrangement, factory silver Brake system: 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, lines extended by approx. 60 cm Lodpfx Abewlmr De Uehr Without ABS, but with mechanical ALB; maximum approved speed 60 km/h Electrics: 12 Volt, multi-chamber lights, no side LED (yellow) lighting, reflectors on side 2 white position lights at front 2 white/red marker lights at rear 1 x 7-pin 12 Volt plug at front, with connection cable, extended by approx. 60 cm 1 LED beacon with holder, switched via sidelights (lamp removable) 2 pairs of warning plates, double LED illuminated and extendable to 3,000 mm Floor: Cranked section at front with steel / checker plate covering Stowage box recessed in the ramp transition near the cranked section Then with 70 mm softwood flooring, steel / checker plate in the wheel arch area Rear bevel with 70 mm softwood floor Low-bed area incl. rear bevel 5,900 mm Ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood covering (front edge with steel/checker plate) Hydraulically operated via tractor PTO with throttle, operation LH side compartment Hydraulic connection with SVK plug NW 10/3, incl. hose Operating notes: For 10,000 kg axle load, a special permit is required, only indivisible loads allowed! The stated total weight is technically possible; depending on the load, it may not be possible to achieve total weight while complying with permissible axle, support, and kingpin loads. (Poor driving and tracking performance possible due to incorrect load distribution) Country of registration / Signs: Registration country: Germany With Dekra inspection and certificate, for max. 60 km/h approval, towing vehicle LoF (agricultural/forestry), (Switzerland max. 40 km/h approval possible) Prepared for double-line license plate holder Without contour marking / reflective tape per ECE R 048 Paintwork: Frame RAL 7021, black-grey "10 years warranty against rust-through" Drawbar hot-dip galvanized Ramps hot-dip

Stanje: rabljeno, Leto izdelave: 2025, obratovalne ure: 20 h, JUWEL 8 M V 5 N 100 OF VF-2025 Lemken Mounted Reversible Plough In standard configuration, additionally equipped with: Version: OF On-land/rough-furrow. Frame Swivel: Frame with hydraulic drawbar Turning Cylinder: with hydraulic tilt adjustment + control unit Tilt Indicator: at the turntable Frame Height: 85 cm, t = 35 (5x) Mouldboard Type: Strip Dural (5x) Support Type: BS42S support on reinforcement. Cranked with hardfacing (5x) Plough Share: Cutting width 42 cm (SB56, strip) Plough Share Version: heavy-duty (5x) Landside: A42H Mouldboard Edge: standard Pendl/Universal Wheel: Universal wheel 340/55-16, inflated Wheel Position: standard Fertilizer Insert Mouldboard: MS2 (5x) Fertilizer Insert Share: Medium, 18 cm Fertilizer Insert Shank Version: standard (5x) Fertilizer Insert Shank Length: standard Throw Angle Adjustment: without throw angle adjustment Disc Coulter: 1 pair D500, smooth, adjacent to drawbar Packarm: Ready for packer arm Lighting System: (EU) preparation, 7-pole connector Working Width per Body: 30-50 cm / 30-55 cm / 36-60 cm Overload Protection: double-cut shear bolt safety BODY SET Lemken Body Set Juwel 8 V L 100 In standard configuration, additionally equipped with: Working Width per Plough Body: 20 - 55 cm Frame Height: 85 cm, t = 35 Support Type: BS42S support on reinforcement. Shares: 2SPS+SB45D/SB56D Landside: A42H Fertilizer Insert: MS2-S245 Fertilizer Insert Shank: standard Landside Disc: 1 pair Suitable for Lemken Juwel 8 M V 5 N 100 Lsdpfxow S N U To Ab Ushr

Stanje: novo, največja dovoljena obremenitev: 18.400 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 5.900 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 860 mm, skupna širina: 2.520 mm, Total weight: 24,000kg / 30,000kg Unladen weight: 5,600kg Lsdpowt Nkrjfx Ab Uehr Payload: 18,400 / 24,400kg Overall length: 10,290mm Loading length: Total 8,070mm; 5,900mm including rear bevel; 2,170mm gooseneck Width: 2,520mm Loading height: 860mm Further information: Additional pre-carriage / provision ex stock 26639 Wiesmoor: €1,280.00 net Steel welded construction Turntable with heavy-duty slewing ring Rear supports, foldable Wheel chocks with holders Full-width rear spray flaps 1 plastic toolbox Preparation for extensions to 3,000mm (pre-drilled holes with covers in outer frame, not in rear slope) Tie-down lugs for low-loader 1 pair of tie-down cutouts recessed in the longitudinal beams at the front on the gooseneck, rated 10t each 7 pairs of lashing mushroom pins set into and on the side of the outer frame, 10t each 1 x front gooseneck 5 x in the well/deck 1 x in rear slope 12 pairs of lashing holes in outer frame, 5t each (for attaching ratchet straps) 5 x gooseneck, 6 x deck, 1 x rear slope Towing equipment for drawbar turntable trailer Drawbar with tested 40 mm towing eye Drawbar height adjustment via spring Axles + Suspension Drum brake axles (manufacturer’s choice) "Laser-measured axles/chassis" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalisation (rocker balance) Wheels and Tyres 235 / 75 R 17.5" (manufacturer’s choice) Steel rims, twin arrangement, factory silver Brake system 2-line compressed air system Spring-loaded parking brake 2 fail-safe coupling heads at the front with connection lines to tractor unit; connection lines extended by approx. 60cm No ABS, but equipped with mechanical ALB; max. approval 60 km/h Electrics 12 volt, multi-chamber lights, no side amber LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marking lights at rear 1 x 7-pin 12V plug front, with approx. 60cm longer connection cable 1 LED beacon with holder, operated by sidelight circuit (lamp removable) 2 pairs of warning panels, double LED illuminated and extendable to 3,000mm Floor Gooseneck at front with steel/checker plate covering Storage compartment recessed in ramp slope to gooseneck After that, 70mm softwood floor; wheel arch area with steel/checker plate Rear slope with 70mm softwood floor Lowbed area including rear slope 5,900mm Ramps Steel ramps, 2,800mm long, 750mm wide, laterally adjustable Wood-covered (tip area with steel/checker plate) Hydraulically operated via tractor PTO with throttle, operated from left side Hydraulic connection with SVK plug NW 10/3 and connecting hose Operating instructions With 10,000kg axle load, special permit required, only indivisible loads allowed!!! Stated total weight is technical maximum; depending on load type, max. permitted axle/support/kingpin loads may not be reached. (Poor handling or tracking due to incorrect load distribution possible.) Country of Registration / Plates Country: Germany With Dekra inspection and certificate, max. 60 km/h approval, towing vehicle LoF (Agricultural or Forestry), (For Switzerland: max. 40 km/h) Prepared for two-line license plate holder No contour marking/reflective strips to ECE R 048 Paint Frame: RAL 7021 black grey "10-year warranty against rust-through" Drawbar galvanized or black (manufacturer’s choice) Ramps hot-dip galvanized

Stanje: novo, največja dovoljena obremenitev: 24.300 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.080 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.520 mm, First registration: New vehicle from stock HU: Gross weight: 24,000 kg / 30,000 kg Unladen weight: 5,700 kg Payload: 18,300 kg / 24,300 kg Overall length: 10,300 mm Loading length: Total 8,080 mm, low bed 5,900 mm incl. rear bevel, 2,180 mm neck width: 2,520 mm Loading height: 900 mm Further information - Welded steel construction - Frame in Novagrau Lodowtlknjpfx Ab Ujhr - Folding rear support - Large lashing package - Parabolic suspension - Twin tyres 235/75R17.5 - Toolbox in neck - Steel ramps 2,800 mm x 750 mm, with spring-assisted lifting - Ramps laterally adjustable

Stanje: novo, največja dovoljena obremenitev: 23.800 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.550 mm, Oprema: ABS, Our complete selection of vehicles with immediately and short-term available units can be found on our website. Extract from the equipment. Complete equipment details available on request. Weights: * Permissible gross weight: 24 t * Technical gross weight: 30 t Dimensions: * approx. 2,100 mm = raised front platform incl. gooseneck, front corners chamfered * approx. 5,350 mm = low-bed platform – flat loading area * approx. 850 mm = rear drive-on slope * Overall width approx. 2,550 mm (or with extensions approx. 3,000 mm) * Load height when loaded approx. 870 mm * When operating as a combination, ensure legal overall height and length limits are observed! Frame: * Steel welded construction with front gooseneck and chamfered rear * Drive-on slope with central excavator bucket recess = indentation at the rear between the longitudinal beams, approx. 2,300 mm long * Integrated in the outer frame: 5 pairs of approx. 4 t lashing bars (4x in the low-bed, 1x on the raised platform) * 7 pairs of recessed, pull-out approx. 10 t lashing rings (4x in the low-bed, 1x at the drive-on slope, 2x on the raised platform) * Standard ball race turntable Frame attachments: * Both sides of the low-bed platform with extendable extensions with softwood planks approx. 50 mm (track width of construction machines to be transported must not exceed the outer frame width of approx. 2,550 mm) * 4 pairs of foldable approx. 10 t lashing rings. Distribution: 1 pair at the front of the raised platform, inside the longitudinal beams; 1 pair to the very rear in the excavator bucket recess left and right; 1 pair at the front of the raised platform before the gooseneck, inside the longitudinal beams; 1 pair at the rear of the low-bed before the drive-on slope, in the bucket recess left and right. Draw device: * Fixed drawbar with swivel towing eye approx. 40 + 50 mm, cranked design, silent bushing mount, drawbar retaining spring with tensioner * Truck coupling height approx. 830 mm to approx. 1,030 mm * Drawbar length approx. 1,800 mm Lsdjwx Dcyjpfx Ab Ushr Support device: * 2 automatic folding supports at the rear Axles: * 3 SAF air suspension low-bed axles with drum brakes * Axle load capacity 11 t/axle * S-cam brakes approx. 300/200 mm * Automatic brake slack adjusters Wheels: * 12 pcs. tyres 235/75 R 17.5, 141J, brand by factory choice * 12 pcs. steel rims 6.75 x 17.5, with offset, silver Brake system/Suspension: * Dual-line air brake system according to ECE regulation R13 * Brake system by Wabco * EBS system 4S3M, sensing on 1st + 2nd axle * RSS/RSP – Stability Program * Spring-loaded parking brake on 2nd + 3rd axles * Steel air tanks * Brake/air connecting lines with 2 single coupling heads yellow/red * EBS/ABS connection cable * Elastics as holder for EBS and electrical plugs * Air suspension with lifting and lowering facility (rear axles only), automatic ride height adjustment from 15 km/h (RTR), axle stop on front axle Floor: * Softwood floor approx. 50 mm, impregnated, protruding approx. 5 – 10 mm above the upper frame edge * Steel checker plate covers above wheels Ramps: * 2 pcs. foldable single-section lightweight steel drive-on ramps, length approx. 2,800 mm, width approx. 750 mm, with hardwood floor approx. 35 mm, impregnated * Ramps adjustable in width from intermediate gap approx. 350 mm to max. overall width approx. 3,000 mm * Ramps can be locked in driving position by chains with tensioner * Ramp lifting aid with spiral spring * Ramps can be moved manually sideways with

Stanje: dober (rabljeno), konfiguracija osi: 3 osi, skupna dolžina: 13.600 mm, skupna širina: 2.500 mm, skupna višina: 900 mm, vzmetenje: zrak, velikost pnevmatike: 7.50 R20, barva: drugo, Konfiguracija osi Zavore: bobnaste zavore Vzmetenje: zračno vzmetenje Sprednja os: Velikost pnevmatik: 7.50 R20; dvojna montaža; Maks. osna obremenitev: 8.000 kg; Znamka osi: BPW Zadnja os 1: Velikost pnevmatik: 445/45 R19.5; Maks. osna obremenitev: 8.000 kg; Znamka osi: ROR Zadnja os 2: Velikost pnevmatik: 445/45 R19.5; Maks. osna obremenitev: 8.000 kg; Znamka osi: ROR Zadnja os 3: Velikost pnevmatik: 445/45 R19.5; Maks. osna obremenitev: 8.000 kg; Znamka osi: ROR Teže Lastna teža: 7.500 kg Nosilnost: 26.500 kg Skupna dovoljena masa: 34.000 kg Stanje Tehnično stanje: dobro Vizualno stanje: dobro Poškodbe: nobenih Ledpfx Aeur Sx Hjb Uehr

Stanje: rabljeno, številka stroja/vozila: GE12/084/2023, lastna masa: 7.000 kg, največja dovoljena obremenitev: 17.000 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/1998, vzmetenje: jeklo, Oprema: osrednja vrtljiva plošča, Vehicle from 1st owner Goldhofer TU3-24/80 Lodjmx U Dpspfx Ab Uohr Low loader Service history maintained Inspection book Hydraulic ramps Payload – 17,000 kg Lashing eyes in the loading area Commercial/export net price – €9,990 Subject to alterations, prior sale, and errors excepted. ===== Telephone Mobile =====