Priklopnik sedeža z delovno ploščadjo

MÜLLER-MITTELTAL 3-Achs Satteltieflader überfahrbar m. Radmulden

Stanje: novo, največja dovoljena obremenitev: 37.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2024, * TS 3 RM 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tyre pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW axles * Air suspension with lifting and lowering device as well as RtR valve * Last axle is a trailing steering axle with electro-pneumatic steering lock * Side underrun protection * Support winches at the front and swivel supports at the rear of the chassis * 15-pin electrical connector * LED tail lights * Mechanically adjustable warning sign packages front and rear * Rotating beacon (removable) rear left * Straight sheet steel mudguards Hjdpfjl Tiiyox Ah Ejw * Spare wheel holder in front of the bulkhead crossmember (without spare wheel) * Saddle platform with 45° bevelled front corners and toolbox at the front made of galvanised, powder-coated sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminium side boards (RAL 9010), foldable and removable, fitted to the side of the saddle platform * Rear wall -150 mm- slotted in * Rear bevel on saddle platform to low bed, approx. 700 mm long, each with 1 recessed lashing ring * Saddle platform with 50 mm clamped timber planks and low-bed platform with 60 mm clamped timber planks * Tread plate above axles * 9 x mechanical folding widenings for up to 3 m overall width, but not in the rear bevel (widening planks available with closed storage compartment across to the direction of travel underneath the loading area) * 2 lashing bars each recessed in the side outer frame of the saddle platform, 3 lashing rings each on the side of the low-bed platform, in addition 1 lashing ring centre rear at the end cross member, 2 x 5 t lashing rings each bolted below the outer frame of the wheel recesses on the side * 2 x 6.4 t UVV lashing rings each in the excavator stick recess * Excavator stick recess from the end of last rigid axle over steering axle right up to the end cross member, continuous, with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm * Each side with 2 wheel wells, 390 mm deep and 640 mm wide with retractable cover for transport of wheel loaders with a wheelbase of 3,120 – 3,620 mm; front well bottom angled up 1,100 mm over 2,050 mm length, rear well bottom angled up 580 mm over 1,550 mm length * Hydraulic folding ramp with extendable tip, approx. 4,650 x 720 mm, incl. load holding valves and hydraulic lateral ramp shift * Outer plank on ramp made of 50 mm hardwood * Loading area above fifth wheel: approx. 3,950 x 2,480 mm * Loading height unladen: approx. 1,470 mm * Lower loading area: approx. 8,500 x 2,520 mm * Loading height unladen: approx. 910 mm (including 860 mm approach ramp) * Chassis, rear folding supports, ramps, mechanical folding widenings are hot-dip galvanised * -- Axles, springs, air tanks painted in black tone -- * Suitable for 2- and 3-axle tractor units * Saddle height: approx. 1,220 mm * Tyres: 235/75R17.5 * Permissible gross weight of 48,000 kg technically possible * Vehicle is hot-dip galvanised * Side boards painted in RAL 9010 pure white * Side walls in any RAL colour available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf