Ctc Za90Srt47 Tieflader 11.87M+Hydr. Rampen nakup rabljenega (2.702)

Stanje: novo, največja dovoljena obremenitev: 45.250 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.550 mm, Oprema: ABS, Our entire range of vehicles, including immediately and short-term available units, can be found on our website. Excerpt from the equipment list. Full equipment details available upon request. Chassis, cranked: * Special steel frame made of high-strength fine-grain steels, electrically welded at connection points * Well-dimensioned outer frame, 4-axle configuration * Wheel coverings above the axles with spray mist suppression * All steel parts shot-blasted * Side underride guard made of anodised aluminium, installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special configuration in the cranked area for maximum low bed length, combined with AluLeg drop-down supports instead of telescopic support winches, maximum rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special body construction * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions can be extended for loading and unloading to approx. 4,200 mm * Three sliding stanchions per side with spring-assisted lifting * Additional central stanchion locks in the roof rail and parked position by pull cable and spring bolt * DINKEL mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable on both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments, with adjustment in the stanchions * Front cover at the bulkhead for driving under tarp, total height up to approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the side, lower 450 mm pockets, above that 4 rows of individual pockets. In the raised bed, only 3 rows of plug-in slats, with uniform spacing Floor: * Approx. 27 mm special waterproof bonded beech plywood, slip-resistant surface * Steel sheet in wheel arch areas, forklift-rated to DIN standard * Outer frame with flush surface Brakes: * WABCO air brake system with EBS according to EC regulation 71/320 EEC incl. PREV (parking-release safety valve) * Spring-loaded brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-bed configuration * Air suspension with lifting and lowering system, total travel approx. 230 mm * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: Ijdpfx Aewx Dbijpneti * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * without spare wheel Lighting: * As per EC regulation, incl. LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights in the front wall, inside, at the top Paintwork: * Chassis and body in single colour RAL 3002 Carmine Red * Central stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signage at front and rear in galvanized, continuously telescopic version with mounted contour lights including plug bases for beacon lights (small panels) * Additional external unlocking for sliding roof frame * 4 stanchion adapters for special outer frame profile, to lock central stanchions as required * PVC sliding tarpaulins, colour similar

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 1985, Ravna prikolica CTC SPA RP26S Itsdpfx Apezl Rx Esnei Prva registracija: 1985 3 osi Pnevmatike v stanju 40/50 % Dolžina: 9,68 m, širina: 2,50 m, nosilnost: 19.500 kg Dvojne hidravlične rampe Splošno dobro stanje Na voljo takoj OVREDNOTIMO MENJAVE VOZIL VSEH ZNAMK, MAN, MERCEDES, DAF, RENAULT, VOLVO, SCANIA, Z OPREMO CIFA, SERMAC, PUTZMEISTER; ALI GRADBENE STROJE CATERPILLAR, FIAT HITACHI, KOMATSU

Stanje: novo, lastna masa: 3.120 kg, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.280 mm, širina tovornega prostora: 2.480 mm, vzmetenje: jeklo, velikost pnevmatike: 245 / 70 R 17,5, medosna razdalja: 990 mm, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 245 / 70 R 17,5, velikost zadnje pnevmatike: 245 / 70 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, per ramp approx. 2,700 mm long x 900 mm wide, ramps with grating, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 lashing eyes each 6 t, steel side panels, foldable and removable, 50 mm wooden planks, loading area tapered at the rear, internal loading width 2,480 mm, removable rear stake, open at the front for through-loading, also available with 5,300 mm load area length! Rental price from €500, -- Errors, misprints and alterations excepted, sample images -- More data on request!, More details:! Itedpfjzmd Dkox Apnoi

Stanje: novo, lastna masa: 3.120 kg, največja dovoljena obremenitev: 8.780 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.280 mm, širina tovornega prostora: 2.480 mm, vzmetenje: jeklo, velikost pnevmatike: 245 / 70 R 17,5, medosna razdalja: 990 mm, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 245 / 70 R 17,5, velikost zadnje pnevmatike: 245 / 70 R 17,5, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, per ramp approx. 2,700 mm long x 900 mm wide, ramps with grating, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 lashing eyes each 6 t, steel side walls, foldable and removable, 50 mm wooden planks, loading platform tapered at the rear, internal loading width 2,480 mm, removable rear stanchion, open at the front for through-loading. Also available with a loading platform length of 5,300 mm! Rental price from €500. -- Subject to misprints, errors and changes. Sample images -- More data at: !, More Details: ! Itsdpszl Tw Dofx Apnsi

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 113 kg, največja dovoljena obremenitev: 637 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, dolžina tovornega prostora: 2.010 mm, širina tovornega prostora: 1.060 mm, višina nakladalnega prostora: 300 mm, Leto izdelave: 2026, Scope of delivery: 1x Basic 750kg car trailer including jockey wheel 1x Mesh extension 40 cm, disassembled (assembly possible for an additional charge) Description: The Martz Basic 750kg car trailer is the ideal solution for all your transport needs. Whether you need to dispose of garden waste, transport building materials, or plan a move – this box trailer offers you the flexibility and durability required. With a payload of 637 kg, you can easily transport heavy loads. The loading area measures 2010 mm in length and 1060 mm in width, providing ample space for various types of goods. The trailer features a sturdy bolted steel frame for enhanced strength. The floor is made from robust phenolic plywood, ensuring longevity even during intensive use. Practical features include a jockey wheel for easy maneuvering, as well as pre-installed tarp buttons for hassle-free tarpaulin attachment. The side panels are also made from durable steel with a height of 300 mm, offering extra protection for your cargo. Equipped with a V-type drawbar and a 7-pin plug, the trailer is compatible with most vehicles. It has an overall length of 2910 mm, a total width of 1490 mm, and a total height of 800 mm, making it compact for simple storage and handling. For further versatility, the trailer comes with a 40 cm mesh extension supplied disassembled. For an additional fee of €30, the mesh extension can be completely assembled to better suit your individual requirements. Ijdexp Ruujpfx Apnjti Order the Basic 750kg car trailer including jockey wheel and mesh extension now to benefit from its versatility and robust design! Technical specifications: - Jockey wheel - Pre-installed tarp buttons Gross weight: 750 kg Unladen weight: 113 kg Payload: 637 kg Loading area length: 2010 mm Loading area width: 1060 mm Total width: 1490 mm Overall length: 2910 mm Overall height: 800 mm Side panel height: 300 mm Side panel material: Steel Mesh extension height: 40 cm Manufacturer: Martz Plug type: 7-pin Trailer type: Box trailer Drawbar type: V-type Floor: Phenolic plywood Frame type: Bolted Frame material: Steel Intended use: Gardening, household applications, removals/furniture transport

Stanje: rabljeno, skupna masa: 109.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2013, skupna širina: 2.750 mm, Oprema: ABS, Identifikacijska številka vozila: XNJ76C5UC12H01185 Električna hidravlika – NATO vtičnica Dovoljena teža sedla: 25.000 kg – Osne obremenitve: 7 x 12.000 kg Skupna masa: 109.000 kg Lastna masa: 19.820 kg Iodpfx Apszhdhfeneti Tehnični pregled v Nemčiji zapade Labodji vrat: 4.300 mm Višina sedla: 1.300 – 1.400 mm = zatič 3,5 palca Spodnji del prikolice (tiefbett): dolžina: 12.415 mm (od tega 300 mm poševno) – širina: 2.750 mm – višina nakladanja: ca. 880 mm MOŽNOST RAZŠIRITVE do 3.200 mm Obešalne tirnice Tehnične osne obremenitve: 7 x 12.000 kg Broshuis osi z bobnastimi zavorami – HIDRAVLIČNO VZMETENE Os 1 + 2 dvižni 6 x krmiljene osi, hidravlično prisilno vodene Centralno mazalni sistem Pnevmatike: 245/70 R17,5 Pridržujemo si pravico do sprememb, vmesne prodaje in napak. Opis služi za splošno identifikacijo vozila in ne pomeni jamstva po kupnopravnem pravu. Za obvezno je šteje opis, določen v prodajni pogodbi. Naša ponudba je načeloma brez novega tehničnega pregleda (TÜV). Če želite nov tehnični pregled, vam lahko posredujemo ponudbo naših partnerskih servisov! Vozilo je lahko polepljeno ali označeno z reklamami. Veljajo naši splošni pogoji dobave in plačila.

Stanje: pripravljen za uporabo (rabljen), Funkcionalnost: popolnoma funkcionalen, lastna masa: 7.440 kg, največja dovoljena obremenitev: 23.560 kg, skupna masa: 31.000 kg, konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 11.000 kg, dovoljena osna obremenitev (os 2): 11.000 kg, prva registracija: 08/2015, naslednji pregled (TÜV): 07/2027, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.550 mm, skupna dolžina: 12.830 mm, skupna širina: 2.550 mm, vzmetenje: zrak, stanje pnevmatik: 50 odstotek, Leto izdelave: 2015, Oprema: ABS, Lep nizkotovorni prikolica z neprekinjeno elektrohidravlično rampo (NATO vtičnica na strani vozila). Idealno za viličarje, gradbene stroje in dvižne platforme. Prikolica je pocinkana, zato ni rje. Iedpfx Aezkkgaspnsti Na splošno je v dobrem stanju. Trenutno se še uporablja. Viličar seveda ni vključen. Če imate kakršna koli vprašanja, se obrnite na nas.

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 205 kg, največja dovoljena obremenitev: 545 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, Scope of delivery: 1x Martz car trailer 296x150cm with jockey wheel, 750kg Description: The Martz car trailer 296 x 150 cm with jockey wheel is a versatile and robust box trailer with a permissible total weight of 750 kg. With its large loading area, sturdy anti-slip plywood floor, and galvanized steel side walls, this trailer is ideal for both private and commercial transport needs. Whether for gardening, household and yard work, renovations, moving, furniture transport, or goods transport – this Martz car trailer offers ample load space and practical features for a variety of transport tasks. The cargo area, measuring 2960 mm in length and 1500 mm in width, enables the transportation of bulky goods, tools, building materials, garden waste, or furniture. The Martz car trailer comes equipped with a jockey wheel. This makes it easier to maneuver, park, and hitch the trailer when unhooked, especially convenient for frequent use. Itsdpfey U T Idsx Apnei Additionally, 4 lashing rings are installed to reliably secure your load. This ensures that furniture, machines, boxes, garden equipment, or other cargo can be fixed securely during transport. Technical data: - Jockey wheel - 4 lashing rings installed - Front and rear walls foldable Gross weight: 750kg Unladen weight: 205kg Payload: 545kg Load area length: 2960mm Load area width: 1500mm Total width: 1930mm Total length: 4060mm Overall height: 920mm Side wall height: 400mm Side wall material: galvanized steel Equipment: jockey wheel, installed lashing rings Manufacturer: Martz Trailer type: box trailer Type of suspension: rubber torsion axle Drawbar type: V-drawbar Floor: anti-slip plywood Tyres: 155/70 R13 Frame type: bolted Frame material: steel Application: gardening, household use, moving/furniture transport, goods transport, and much more Matching high tarpaulin 140cm, €650 We are happy to send you the vehicle registration documents in advance free of charge if you opt for 'self-collection'!

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar / Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Electrics / Lighting: * TPMS (tyre pressure monitoring system) * 15-pin power connector * LED tail lights ----General Attachments: * Jost landing gear at the front * Outward folding rear supports * Tool box made of galvanized steel sheet, approx. 650 x 350 x 320 mm, mounted on the right side (powder-coated black) * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Reinforcement package for drill rig transport on the chassis – loading height +20 mm * 50 mm softwood floor, clamped design * Preparation in front of the front wall for subsequent installation of container locks * Bolted smooth steel front wall * Fold-down trapezoidal-profile steel side walls with board-lift assist * Steel rear wall, slidable between ramps – storage bracket for unused position inside, in front of the headboard * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Front and rear corners each fitted with 1 x 10 t lashing ring; multiple holes for 1.2 t lashing options in front and rear crossmembers ----Ramps: * One-piece, mechanical grate ramps with spring system for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm gap) * Rear access angle approx. 860 mm ----Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ----Paintwork: * Chassis, drawbar, front wall, tailgate, rear folding supports, and ramps hot-dip galvanized Itjdpfepk D D Hjx Apnei * Axles, springs, air tanks and landing gear painted in a shade of black * Sideboard painting in RAL 9010 pure white * Painting of side walls in an individual RAL color available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with equalizer unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by 300 mm * 40 mm flange drawbar eye ----General Attachments: * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic quarter mudguards * Plastic toolbox, front right, mounted externally on bulkhead ----Electrics / Lighting: * TPMS Tire Pressure Monitoring System * LED lighting ----Loading Platform: * Loading length: 6.27 m * Suitable for container transport * 50 mm softwood floor * Preparation in front of bulkhead for retrofitting container locks * Bolted smooth steel bulkhead * Hinged, trapezoidal-profile steel side panels with drop-side spring assist * Removable steel rear wall, can be stowed in front of the bulkhead between ramp mounts * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t recessed lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in the bulkhead and end beam for 1.2 t lashing options ----Ramps: * One-piece mechanical drive-up ramps with spring mechanism, single-operator use, approx. 2,750 x 600 mm (collapsible down to 20 mm) * Rear approach angle approx. 860 mm ----Tyres: * Tyres: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, rear wall, rear stanchions, and drive-up ramps * Side panels painted in RAL 9010 pure white * Painting of side walls in an individual RAL color available for a surcharge ----Information: * Subject to errors and prior sale Iodpfx Aoq Ra D Espnsti * New vehicle with manufacturer warranty ----Delivery time: * Available from CW

Stanje: novo, največja dovoljena obremenitev: 15.970 kg, skupna masa: 21.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 21.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Lighting / Electrics: * 15-pin power connector * LED lights 12/24 V * RDÜ tire pressure monitoring system ----General Equipment: * Jost landing gear in the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Preparation at the front bulkhead and rear incline for subsequently mounting container locks for 20" container transport * Design for 21 t GVW with reinforced frame and axles * Reinforcement kit for drill rig transport on the chassis * 50 mm softwood floor, clamped design * Preparation at the front bulkhead for retrofitting container locks * Bolted smooth sheet metal front wall * Split side walls made of trapezoidal-profiled steel sheet, foldable with central drop-in stake * Steel rear wall, insertable between the ramps (can be stored in a holder at the front bulkhead when not in use) * Rear stakes, bolted ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Optional installation of 3 t folding lashing rings every 600 mm * Profifix lashing rail in the longitudinal axis, central, for lashing up to LC 3,000 daN * One 10 t lashing ring in each front and rear corner * Load securing package with two 8 t retractable lashing rings per side, integrated into the outer frame; multiple holes in the front bulkhead and rear cross member for 1.2 t lashing options Iodpfx Apel Tihxonsti ----Ramps: * Single-piece mechanical grid ramps with spring mechanism for single-person operation, approx. 3,000 x 620 mm (can be pushed together to 20 mm) * Rear chassis incline approx. 860 mm ----Loading Heights: * Unladen: approx. 940 mm * Laden: approx. 910 mm ----Wheelbase / Tyres: * 1,810 mm * Tyres: 235/75R17.5 ----Painting: * Painting of side walls in desired RAL color (no special or metallic paints), changeable up to approx. 6 weeks before completion * Drawbar, front wall, tailgate, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks and landing gear painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Example images ----Delivery Time: * Available from calendar week 29 / 2026

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Braking system: * Wabco EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs - 110 mm wide - with tandem compensation unit ----Drawbar / Flange drawbar eye: Itsdpfx Apsl Th Hwjnsi Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Electrics / Lighting: * 15-pin electrical connector * LED tail lights * RDÜ tyre pressure monitoring system ----General fittings: * Jost landing gear at the front * Outboard folding supports at the rear * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood flooring * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Drop sides made of trapezoidal profile steel sheeting, foldable with tailboard spring assist * Steel rear wall insertable between ramps - holder for storage when not in use in front of headboard * Bolted rear stakes ----Load securing: * Perforated outer frame, approx. 45-degree angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * One 10 t lashing ring in each front and rear corner, various drill holes in the front and rear cross-members for 1.2 t lashing options * Profifix lashing rail along the longitudinal axis centre for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be collapsed to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Chassis, drawbar, headboard, rear wall, loading ramps, and folding supports hot-dip galvanized * Drop sides painted in RAL 9010 pure white * Painting of the side walls in a RAL colour available at extra cost * Axles, springs, air tanks, flange drawbar eyes and landing gear painted in a shade of black ----Information: * New vehicle with full manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex-works Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton Gigant axles * Air suspension with lifting and lowering function * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm * Tire pressure monitoring system with display option in the truck via EBS signal—no installation required on the truck side * 15-pin power connector * LED lighting * Front support winch * Rear external fold-out supports * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right outside on the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood flooring * Provisions in front of the front wall and at the rear for retrofitting 20" container locks * Bolted front wall made from flat sheet * Trapezoidal-profile, drop-down steel side walls, centrally divided once * Sliding steel rear wall between the ramps, mounting bracket for storage inside in front of the front wall when not in use * Bolted rear post/stake * Perforated external frame, bent at approx. 45 degrees, with 2-ton lashing capacity every 480 mm * Installation of 3-ton folding lashing brackets possible every 600 mm—4 lashing rings installed on each side * 1 x 6.3-ton lashing ring at each of the front and rear corners * "Profifix" lashing rail centrally in the longitudinal axis for lashing options up to LC 3,000 daN * Various boreholes in the front and rear cross member for 1.2-ton lashing options * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach ramp approx. 860 mm * Chassis, drawbar, front wall, tailgate, fold-out supports, and drive-on ramps hot-dip galvanized Isdjl Th Dfepfx Apneti * Axles, springs, air tanks, flange drawbar eye, and support winch painted black * Side wall paintwork in an RAL color of your choice (excluding special or metallic paints), color can be changed up to approx. 6 weeks before completion * --Reinforced and certified body according to EN 12642 XL, incl. load securing certificate-- * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from approx. calendar week 31 / 2026

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * EBS (Electronic Braking System) * Emergency release mechanism for spring brake cylinders * Drum brakes * 2 x 7 ton Gigant axles * Air suspension with lifting and lowering device * Tow bar height-adjustable by approx. 300 mm * Tow bar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * 15-pin electrical connector * LED lighting * Front landing gear * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm mounted on the front right exterior bulkhead * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provisions for subsequent installation of 20" container locks in front of the bulkhead and at rear * Bolted smooth steel sheet bulkhead * Side walls made of trapezoidal-profile steel sheet, center-folding, divided once * Rear steel panel insertable between ramp mounts; storage inside at bulkhead when not in use * Bolted rear stanchions * Perforated outer frame approx. 45° angled, lashing points (2 t lashing capacity) every 480 mm * Optional installation of 3 t drop lashing brackets every 600 mm – four lashing rings installed per side * One 6.3 t lashing ring in each front and rear corner * Profifix lashing rail along the longitudinal axis center, for lashing capacity up to LC 3000 daN Iodol Thvxjpfx Apnjti * Various holes in front and rear crossmember for 1.2 t lashing options * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Rear driving slope approx. 860 mm * Chassis, tow bar, bulkhead, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, drawbar eye, and landing gear painted black * Side wall paint in desired RAL color shade (no special or metallic finishes), modifiable up to about 6 weeks before completion * -- Reinforced and certified bodywork according to EN 12642 XL, incl. load securing certificate -- * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from approx. week 31/2026

Stanje: novo, največja dovoljena obremenitev: 26.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Vehicle / Body: Low-bed semi-trailer First registration: New vehicle Gross weight: 35,000 kg / 47,000 kg Unladen weight: 8,900 kg Payload: 26,100 kg / 38,100 kg Overall length: 13,300 mm Loading length: 9,200 mm Width: 2,520 mm Loading height: 900 mm Further information Chassis: Low-bed semi-trailer Steel welded structure, fifth wheel plate with replaceable 2" king pin and two king pin positions (not in combination with forced steering) 24 t 2-speed landing gear, single-sided operation, with straight lower part, without thrust compensation Rear support foldable 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mudflap Mud flaps with anti-spray in front of the 1st axle and behind each axle, in accordance with EU regulations 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Extendable width to 3,000 mm (not at the rear taper) (Note: The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Compartment for wooden planks on neck, transverse at front 70 mm wooden planks for extension to 3,000 mm Excavator arm recess over rear axles, extending to the rear, approx. 3,000 mm long, 650 mm wide, and 230 mm deep 2 pairs of lashing holes, each rated 5 t, in the excavator arm recess on side of main frame, approx. 300 mm from front and some 200 mm before rear taper Lashing points low-loader 11 pairs of lashing mushrooms, integrated top and side of the outer frame, each 10t 2x on gooseneck 9x distributed on load floor 2 pairs of lashing eyes front on gooseneck, each 5t 3 pairs of swivel lashing eyes on gooseneck, each 5t Itjdpfjut Idnjx Apnei 2 pairs of folding lashing eyes additionally embedded in load floor, each 10t 1x at beginning of load floor 1x at end of rear taper 1 pair of preparation on the slope from gooseneck for 6.7t screw-on lashing eye (JDT) 8 pairs of ring lashing eyes recessed in outer frame, each 5t (convertible to stanchion pockets) 1 pair screw-on lashing eyes, each 6.7t (JDT), with large flange plate incl. thread as counternut Axles & suspension SAF or BPW drum brake axles, manufacturer's choice “Axle/chassis laser alignment” to reduce tire wear and fuel consumption Last axle is self-steering, with automatic reversing lock via reversing light and additional manual lock function via push button on vehicle Air suspension Wheels and tires 235 / 75 R 17.5" Manufacturer's choice Steel rims, twin configuration, factory silver Braking system 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake 24 Volt EBS, electronic braking system with EBS socket at front, without connecting cable Note: The trailer may only be towed by tractor units that ensure effective ABS functionality! 2 coded coupling heads at front, without connecting line With lift & lower valve Axle load detection via EBS-CAN-bus signal, for display in cab, truck must be appropriately equipped, no truck installation (not a calibrated scale) Vehicle stability control system Tire pressure monitoring system according to ECE R 141, display in tractor cab via EBS, truck installation required Electrics 24 Volt, multi-chamber lights, side yellow LED lighting Side yellow LED lighting linked to indicator "flashing side markers" 2 white position lights at front 2 white/red lane marker lights at rear 2x 7-pin coded sockets at front, without connecting cable 1 LED revolving beacon

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flanged Drawbar Eye: * Height-adjustable drawbar by 300 mm * 40 mm flanged drawbar eye ----General Attachments: Itsdpfx Apjrvvfwensi * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding rear supports * Plastic quarter mudguards * Plastic toolbox mounted front right on the bulkhead ----Electrics / Lighting: * RDÜ tire pressure monitoring system * LED lighting ----Loading Area: * Loading platform length: 6.27 m * Suitable for container transport * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal profile steel, foldable with drop side spring lifter * Steel tailgate, insertable between ramp holders; stowable inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Each front and rear corner fitted with 1 x 6.3 t lashing point * Various holes in bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical drive-on ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be retracted to 20 mm height) * Rear approach angle approx. 860 mm ----Tyres: * Tyres: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paint Finish: * Hot-dip galvanized chassis, drawbar, bulkhead, tailgate, rear stanchions, and ramps * Sideboard paint finish in RAL 9010 pure white * Painting of side walls in another RAL color possible at extra cost ----Information: * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Availability: * Available from CW (calendar week)

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Brakes: * Wabco EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes Itedpol Th Hlsfx Apnji ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs – 110 mm wide – with tandem equalisation unit ----Drawbar / Drawbar Eye: Drawbar with 50 mm flange eye and height-adjustable drawbar ----Electrics / Lighting: * 15-pin electrical connector * LED tail lights * RDÜ tyre monitoring system ----General Attachments: * Jost landing leg at the front * External folding supports at the rear * Side underrun protection * Plastic quarter mudguards ----Low Loader Bed: * 50 mm softwood floor * Preparation in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of trapezoidal-profiled steel, foldable with drop side spring lifters * Steel rear wall can be slid in between the ramps – storage bracket inside in front of the front wall when not in use * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45 degrees bent, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In front and rear corners, each 1 x 10 t lashing ring; various holes in front wall and rear crossmember for 1.2 t lashing option * Profifix lashing rail centrally positioned along the longitudinal axis, with lashing capacity up to LC 3000 daN ----Ramps: * One-piece mech. grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be compacted to 20 mm) * Rear approach slope approx. 860 mm ----Painting: * Chassis, drawbar, front wall, rear wall, ramps, and folding supports hot-dip galvanised * Sideboard painted in RAL 9010 pure white * Painting of the side panels in any RAL colour available at extra cost * Axles, springs, air tank, flange eye and landing leg painted in black ----Info: * New vehicle with full manufacturer's warranty * Errors and prior sale subject to change ----Delivery Time: * Available immediately ex-works at Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ---- Brakes: Iodpfxjpk D Ncs Apneti * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ---- Axles: * 2 x 11 t Gigant axles ---- Suspension: * Air suspension with manual lowering at the rear ---- Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ---- Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * 15-pin power connector * LED tail lights ---- General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm, fitted on the right side (black powder-coated) * Side underride protection * Plastic quarter mudguards ---- Low Loader Platform: * Reinforcement package for drilling rig transport on the chassis – loading height +20 mm * 50 mm softwood floor in clamped design * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal-profiled steel sheet, foldable with board wall spring-assisted lifter * Steel rear wall, can be inserted between the ramps – storage bracket in front of the bulkhead when not in use * Rear stakes bolted ---- Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * Each front and rear corner with 1 x 10 t lashing ring; various holes in the headboard and end cross member for 1.2 t lashing options ---- Ramps: * One-piece mechanical steel grating ramps with spring assistance for one-man operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear access slope approx. 860 mm ---- Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ---- Painting: * Chassis, drawbar, headboard, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing leg painted in black * Side boards painted in RAL 9010 pure white * Side walls can be painted in any RAL color for a surcharge ---- Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ---- Delivery time: * Immediately available from Egestorf

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 146 kg, največja dovoljena obremenitev: 604 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, dolžina tovornega prostora: 2.640 mm, širina tovornega prostora: 1.260 mm, višina nakladalnega prostora: 300 mm, Leto izdelave: 2026, Scope of delivery: 1x Martz car trailer 264x126cm with tipping drawbar and jockey wheel, 750kg Description: The trailer features a V-type tipping drawbar that ensures excellent stability during transit. The chassis comprises bent profiles made of galvanized steel sheet, securely bolted together. The running gear is based on a torsion axle from a renowned manufacturer, providing independent, sprung suspension on a torsion bar. Fitted tires: 155/70 R13. The side panels are constructed from galvanized steel sheet. The rear tailgate can be opened easily and quickly. Load platform: High-quality, waterproof, anti-slip phenolic plywood, 9mm thick. Technical Specifications: - Tipping drawbar - Jockey wheel Gross weight: 750kg Unladen weight: 146kg Payload: 604kg Load bed length: 2640mm Load bed width: 1260mm Overall width: 1690mm Overall length: 3540mm Overall height: 800mm Side panel height: 300mm Side panel material: Galvanized steel Manufacturer: Martz Trailer type: Box trailer Suspension type: Rubber sprung axle Drawbar type: V-drawbar Floor: Phenolic plywood floor (9mm thick) Wheels: 155/70 R13 Frame type: Bolted Itedpfx Aoxpimpopnsi Frame material: Steel Application: Gardening, DIY, moving/transporting furniture, goods transport, and more. The Martz car trailer is the reliable choice for all your transport needs. We are happy to send you the vehicle documents in advance and free of charge if you choose 'collection in person'!

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 146 kg, največja dovoljena obremenitev: 604 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, dolžina tovornega prostora: 2.640 mm, širina tovornega prostora: 1.260 mm, višina nakladalnega prostora: 300 mm, Leto izdelave: 2026, Scope of delivery: 1x Martz car trailer 264x126cm with tipping drawbar and jockey wheel, 750kg Description: The trailer features a V-type tipping drawbar that ensures excellent stability during transit. The chassis comprises bent profiles made of galvanized steel sheet, securely bolted together. The running gear is based on a torsion axle from a renowned manufacturer, providing independent, sprung suspension on a torsion bar. Fitted tires: 155/70 R13. The side panels are constructed from galvanized steel sheet. The rear tailgate can be opened easily and quickly. Load platform: High-quality, waterproof, anti-slip phenolic plywood, 9mm thick. Technical Specifications: - Tipping drawbar - Jockey wheel Gross weight: 750kg Unladen weight: 146kg Payload: 604kg Load bed length: 2640mm Load bed width: 1260mm Overall width: 1690mm Overall length: 3540mm Overall height: 800mm Side panel height: 300mm Side panel material: Galvanized steel Manufacturer: Martz Trailer type: Box trailer Suspension type: Rubber sprung axle Drawbar type: V-drawbar Floor: Phenolic plywood floor (9mm thick) Wheels: 155/70 R13 Frame type: Bolted Frame material: Steel Application: Gardening, DIY, moving/transporting furniture, goods transport, and more. The Martz car trailer is the reliable choice for all your transport needs. Iodpjxpinaofx Apnoti We are happy to send you the vehicle documents in advance and free of charge if you choose 'collection in person'!

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 116 kg, največja dovoljena obremenitev: 634 kg, skupna masa: 750 kg, konfiguracija osi: 1 os, največja hitrost: 100 km/h, Scope of delivery: 1x Basic Car Trailer 750kg with tilting drawbar incl. jockey wheel 201x106cm Iodpfeylhl Djx Apnsti Description: The Martz Basic 750kg Car Trailer with tilting drawbar is the ideal solution for all your transport needs. Whether you need to dispose of garden waste, move building materials, or are planning a house move, this box trailer provides the flexibility and durability you require. With a payload capacity of 634kg, you can easily transport heavy loads. The loading area measures 2010mm in length and 1060mm in width, offering ample space for a wide variety of goods. The trailer is equipped with a sturdy bolted steel frame for added strength. The floor is made from durable phenolic plywood, ensuring resilience even under intensive use. Practical features include a jockey wheel for effortless maneuvering and pre-installed tarp buttons for easy fitting of a cover. The side panels are also made of robust steel and have a height of 300mm, providing extra security for your cargo. The trailer is fitted with a V-drawbar and 13-pin plug. With an overall length of 2910mm, a total width of 1490mm, and a total height of 800mm, it is compact enough for easy storage and handling. Thanks to the practical tilting drawbar, the trailer can be stored upright in your garage or carport to save space. Technical Data: - Jockey wheel - Tilting drawbar - Installed tarp buttons Gross weight: 750kg Unladen weight: 116kg Payload: 634kg Loading area length: 2010mm Loading area width: 1060mm Overall width: 1490mm Overall length: 2910mm Overall height: 800mm Side panel height: 300mm Side panel material: Steel Manufacturer: Martz Plug type: 13-pin Trailer type: Box trailer Drawbar type: V-drawbar Floor: Phenolic plywood Frame type: Bolted Frame material: Steel Intended use: Garden work, household applications, moving / furniture transport For even more versatility, you can acquire optional accessories such as mesh extensions or side panel extensions to adapt the trailer to your specific needs. If you opt for 'collection in person', we are happy to send you the vehicle documents in advance free of charge!

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 398 kg, največja dovoljena obremenitev: 1.602 kg, skupna masa: 2.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 3.010 mm, širina tovornega prostora: 1.530 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, Opis: Prikolica kompletna (uključuje bočne stranice) Isdpjxqpfhofx Apneti Život nam stalno donosi nove izazove. Vaša SySTEMA prikolica raste zajedno sa vama – za ceo život! Danas izgradnja kuće, sutra porodični odmor sa kampovanjem, a za nekoliko godina željeni izlet motorom. Ostanite fleksibilni! Vaša prikolica to već jeste. SySTEMA Light prikolice su dostupne i sa fabrički ugrađenim amortizerima. Ove prikolice se mogu direktno registrovati za brzinu od 100 km/h kod nadležne službe. Dodatni troškovi i odlazak u tehnički servis (npr. TÜV, DEKRA) nisu potrebni. Napomena: Kod SySTEMA Light modela nije moguća naknadna ugradnja šina i rampi! Tehnički podaci: Ukupna težina: 2000 kg Nosivost: 1602 kg Spoljašnje dimenzije: 421 x 202 x 106 cm (D x Š x V) Dimenzije sanduka: 301 x 153 cm (D x Š x V) Dimenzija pneumatika (col): 13 Kočnica: DA Pomoćni točak: DA Amortizeri: Ne (Doplata: 218€ za proširenje na 100 km/h) Maksimalna brzina: 80 km/h

Stanje: novo, lastna masa: 9.800 kg, največja dovoljena obremenitev: 39.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 9.800 kg, Oprema: ABS, Chassis: - Robust welded steel frame construction with a front frame dip and flat loading platform featuring a rear bevel approx. 500x100 mm - Frame neck 200 mm with chamfered corners at the front - Sloped swan neck end approx. 500 x 100 mm (with anti-slip profile strips on outer frame in the area behind the rear bevel) - 2 king pin positions with replaceable 2” king pin Itodpfxsxgm S De Apnji - Outer frame closed to the outside and designed as perforated outer frame - Loading platform with extendable central frame, extendable by around 2,000 mm, lockable in 500 mm increments pneumatically - Frame with 80x80 mm step at and after extension joint - Reinforced frame design / maximum point load when retracted at center of gravity - Without extendible load platform outriggers, but pre-fabricated to allow retrofit (= guide tubes welded in frame) - With excavator trough (no cover), approx. 220 mm deep, 600 mm wide, starting behind 2nd axle to vehicle end - 1 pair of wheel wells between 1st and 2nd axles, covered with steel plates (covers with Körapur coating), approx. 400 mm deep - Rear underrun protection = extended rear plate - Drop-down supports at the rear Ramps: - 2 two-piece loading ramps, special design with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting device (only with electro-hydraulic unit) - Width approx. 800 mm - Wooden surfacing - Including anti-slip strips on ramps - Can be locked in transport position with tie-down straps - Operated by control lever mounted on rear right in frame - Hydraulically laterally adjustable Floor: - 35 mm larch wood floor with aluminium omega profiles Landing legs: - Mechanical 24-ton landing legs with single-sided operation and compensating device Axles, steering and tires: - BPW air suspension axles, each with 10-ton axle load, air bellows diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - Lifting and lowering system with total lift approx. 200 mm - 2nd driving position via ball valve +50 mm - 1st axle lift axle (wired through EBS), automatic control, with manual override button on the trailer - 3rd axle as friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center offset by center bore - 12 tires, 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring system Accessories: - Insertable side and rear stakeboards on the swan neck, approx. 400 mm high - Spare wheel carrier - Side aluminium underrun protection - 4 chocks - 1 plug-in ECE rear warning board - 11 pairs of ZK modules 10t, lateral: - 2x on the swan neck - 2x on loading area before extension - 7x after extension - Extendable warning signs including 3 position lamps each, at the front on landing legs and rear before the rear plate, steplessly extendable up to 4,500 mm loading width - 4 plug-in sockets for warning signs in stake pockets on the loading platform - 6 pairs of stake pockets laterally for 100x50 mm stakes - 2 cross rows stake pockets for 100x50 mm stakes on swan neck, from outer frame to main frame (1x before/1x after king pin positions) - 3 cross rows stake pockets for 100x50 mm stakes on loading area from outer frame to main frame (1x before the extension, 1x after extension, 1x after the 3rd axle) - 2 pairs of steel plates in the loading platform for container locks to accommodate 1x 20ft container - Rubber apron mounted on underrun protection

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, New 750 kg Low-Loader Car Trailer – Top Quality For sale is a brand-new car trailer, ideal for versatile use in private or commercial sectors (transport, construction, gardening, etc.). 🔧 Technical Specifications: Type: Low-loader Permissible Total Weight: 750 kg Payload: approx. 630 kg Axles: 1 Braked: No Tyres: 13 inch Internal Dimensions (LxWxH): approx. 202 x 114 x 30 cm ✅ Features & Equipment: Robust, fully galvanized steel construction (corrosion-resistant) Sturdy frame design with reinforced drawbar Rubber suspension axle for smooth driving performance Side panels made of solid steel – durable and resilient Lashing eyes for secure load securing Fittings for tarpaulin / bows present Protected lighting 👍 Advantages: Iodjy Dru Ispfx Apnoti Brand new (unused) Low-maintenance and durable Compact dimensions – also suitable for smaller vehicles Versatile applications (furniture, building materials, green waste, etc.) 📦 Availability: Delivery possible Available within a few weeks 📍 Collection & Delivery: Collection in Buchholz (Aller) possible Nationwide delivery within Germany available on request 💰 Note: The quoted price includes the basic trailer in standard configuration. Accessories and additional equipment (e.g., superstructures, extensions, etc.) are available separately on request. Your Team Globaltainer GmbH

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, lastna masa: 947 kg, največja dovoljena obremenitev: 2.553 kg, skupna masa: 3.500 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 3.600 mm, širina tovornega prostora: 1.700 mm, višina nakladalnega prostora: 300 mm, vzmetenje: parabolično listje (vzmet), velikost pnevmatike: 195/60R12C, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2025, Različica prekucnika za gradbene stroje z nizko nakladalno višino ► Model 3517MT ► Mere kesona pribl.: 360 x 170 x 30 cm (D x Š x V) ► Dovoljena skupna masa: 3500 kg ► Lastna masa pribl.: 947 kg ► Parabolične listnate vzmeti ► Hidravlična črpalka in baterija ► Pnevmatske gume 195/60R12C ► 10 x pritrdilne zanke ► Nadgradnja, pocinkano jeklo Itodpfx Apjxb Uxuenoi Dodatno, vključeno v ponudbeni ceni: ► Vzponi 2,8 t / 175 cm ► Par podpornih nog ► Odlagalnik za lopato ► Jeklena talna plošča