Faymonville 4-Axle Semi-Lowbed Trailer 65 T + Ramps Ext. nakup rabljenega (67.980)

Stanje: rabljeno, lastna masa: 11.880 kg, največja dovoljena obremenitev: 49.920 kg, konfiguracija osi: 3 osi, prva registracija: 05/2026, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Vratni del (»swan neck«): - Vratni del z zadnjim naklonom približno 750 mm x 10° - 3 pari pritrdilnih obročev (nosilnost 5.000 daN) - Obloga iz trdega lesa, debeline 30 mm Nosilna ploščad: - Nosilna ploščad v izvlečni izvedbi z zadnjim naklonom približno 1.000 mm x 8° - 5 parov pritrdilnih obročev, ki se odklopijo navzven (nosilnost 5.000 daN) - 3 pari pritrdilnih obročev, ki se odklopijo navzven (nosilnost 10.000 daN) - 1 par pritrdilnih obročev, nameščenih vodoravno na sprednji strani nosilne ploščadi (nosilnost 10.000 daN) - Odprtine na zunanjem okvirju nosilne ploščadi za pritrditev zateznih pasov (nosilnost 2.000 daN) - Obloga iz trdega lesa, debeline približno 48 mm, nad osmi je obloga iz profilirane pločevine Rampe: - En par pocinkanih, dvodelnih jeklenih ramp, približno 2.750 + 1.400 x 800 mm, z oblogo iz trdega lesa, debeline približno 48 mm Ljdozp Ntvepfx Ag Esaf - Rampa z hidravlično dvižnimi in zložljivimi deli rampe, hidravličnim dvigalom in hidravlično premikalnim mehanizmom - Največja obremenitev na par: 40.000 kg Podporni noge: - JOST podpirne noge (mehanske) z 2-stopenjskim menjalnikom za dvigovno silo 24 t (testna obremenitev 50 t) Osi in pnevmatike: - BPW osi, dve osi fiksni, dve osi krmilni - Z zračno vzmetjo, z bobnastimi zavorami, z funkcijo dvigovanja/spuščanja - Krmilne osi s elektromagnetno blokado pri vzvratni vožnji, ki se aktivira s prestavo za vzvratno vožnjo ali ročno - Sistem za nadzor tlaka v pnevmatikah (TPMS) v skladu s standardom ECE R 141 - Pnevmatike 235/75 R17.5 Barvanje: - Peskanje s korundom za optimalno oprijemljivost prevlečnega sistema - HRM metalizacija celotnega šasija vozila z ZINACOR 850 (85 % cink/15 % aluminij) - Končni premaz z 2 slojema 2K lakom, enobarvno v barvi DB 7350 Novograu Dodatna oprema: - Na vratnem delu in na zadnji strani, levo in desno, po en nosilec za opozorilne table, vključno z vtičnico - En rezervni zagon z nosilcem - 2" kraljevska glava (King Pin) - En pocinkani jekleni sprednji panel, visok približno 400 mm - Na pocinkani priključni letev spredaj, rumeno-rdeče zračne sklopke - 4 podložni klini z nosilcem - Pocinkani, zložljivi podporni noge pod naklonom nosilne ploščadi - En nosilec za krožno luč na zadnji strani prikolice - Pokrovne plošče za zapiranje prostora med rampami in nosilno ploščadjo - Bela odsevna trak v skladu z evropskimi predpisi, bočno in na izvlečni plošči, zadaj rdeč - Elektro-hidravlična agregat zadaj, pod nosilno ploščadjo - Upravljalni ventili za rampe, nameščeni na desni strani prikolice - En odbijač na zadnji strani - Evropske odsevne table (rdeče-rumene) na zadnji strani prikolice - Navodila in opis na USB pomnilniku - Štiri opozorilne table, ki se iztegnejo za približno 400 mm, približno 423 x 423 mm z pozicijsko lučjo - Na vratnem delu lahko pritrdite ALU stranske in zadnje stene, približno 2.440 x 400 mm - Zadnje, pocinkane priključne lege so odstranljive (dolžina nadstavka približno 2.560 mm) - 4 pari WADER stranskih vreč na nosilni ploščadi za 1x 20-stopalni, 2x 20-stopalni ali 1x 40-stopalni kontejner - 7 parov stranskih vreč za priključne lege 100 x 50 mm na zunanjem okvirju nosilne ploščadi - Razširitve, pocinkane, iztegljive za približno 230 mm na vsaki strani - Dvigni os na sprednji osi, upravljanje preko TEBS-E, odvisno od trenutne obremenitve osi in trenutnega stanja obremenjenosti - Kvadratne lestve 20 x 20 mm, v razmiku 200 mm, na zunanjem okvirju naklona nosilne ploščadi - Na profiliranih pločevinah na vratnem delu in na nosilni ploščadi nanesen

Stanje: novo, največja dovoljena obremenitev: 48.930 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Celotno zalogo vozil, vključno z vozili, ki so na voljo takoj in v kratkem roku, najdete na naši spletni strani. Izvleček iz opreme. Popolna oprema na zahtevo. "Gooseneck" prikolica * s poševnimi robovi spredaj, približno 45° in z zadnjim poševnim robom, približno 750 mm x 10° * 3 pari pritrdilnih obročev (nosilnost 5.000 daN) * trdna lesena obloga, debeline približno 30 mm Tovorilna površina * dvodelna, izpodvlačna izvedba z zadnjim poševnim robom, približno 500 mm x 8° * 5 parov pritrdilnih obročev, ki se zunanji prepognejo (nosilnost 5.000 daN) * 4 pari pritrdilnih obročev, ki se zunanji prepognejo (nosilnost 10.000 daN) * 1 par pritrdilnih obročev, nameščenih ležeče na sprednji strani tovorilne površine (nosilnost 10.000 daN) * 1 vmesna miza, približno 250 mm * izrezi v zunanjem okvirju tovorilne površine za pritrditev zategovalnih trakov (nosilnost 2.000 daN) * trdna lesena obloga, debeline približno 48 mm, nad osmi je valjasta kovinska obloga Osi * osi BPW, hidravlično-mehansko sinhronizirano krmiljenje * tehnična nosilnost osi: 12.000 kg na os * zračna vzmetenje z ventili za dvig in spuščanje Pnevmatike * 245/70 R 17.5 3PMSF, indeks obremenitve (146/146 F) * TPMS sistem za nadzor tlaka v pnevmatikah, v skladu s standardom ECE R 141 Opore sedla * JOST opore sedla (mehanske) z dvostopenjsko prestavo za približno 24 t nosilnosti (približno 50 t testna nosilnost) Zavorna naprava * v skladu z direktivami EU z EBS-E (4S3M) Lsdpfx Ajzlwm Aeg Eeaf Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * vrste jekel: S355J2+N/S355MC (meja tečenja 355 MPa) * S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu z direktivami EU, osvetlitev 24 voltov ASPÖCK-NORDIK (ASS3) * vse LED stranske markerne luči utripajo sinhronizirano s smerniki * ASPÖCK-UNIBOX na priključni letev spredaj s vtičnicami 24N, 24S & 15-polni priključek, v skladu s standardom ISO. 24N ISO-1185 24S ISO-3731 15-polni ISO-12098 Barvanje * celotna jeklena konstrukcija, po varjenju, avtomatsko peskana z metodo vrtinčenja * drugo peskanje s korundom za optimalno oprijemljivost prevlečnega sistema * HRM-metalizacija celotnega podvozja vozila z ZINACOR 850 (85% cink/15% aluminij) za zagotovitev najboljše zaščite proti koroziji * končna barva z 2 plastma 2K-lak, enobarvno, v RAL 3002 Karminrot, v skladu s sistemom RAL 841GL * platišča v srebrni barvi. Zadnji del je metaliziran in pobarvan v RAL 9010 (čista bela) * metalizirano barvanje ni mogoče * test barvne strukture izveden v testu meglenega spreja s soljo, v skladu s standardom ISO 9227-NSS * zaščita notranjih prostorov s posebnim voskom Vključno z naslednjo dodatno opremo 2-palčni kraljevi vtič * elektro-hidravlična agregat (± 45 kg) * dodatno krmiljenje od spredaj in od zadaj s kablom, upravljanje s pritiskovnimi gumbi, z nadzorom posameznih osi (brez vgradnje v centralno krmilno enoto) * na "gooseneck" prikolici in na zadnji plošči, na levi in desni strani, držalo za opozorilne table, vključno z vtičnico * držalo za okroglo luč na zadnji strani prikolice * na "gooseneck" prikolici aluminijaste stranske stene in zadnja stena, ki se lahko vstavi, približno 2.440 x 400 mm (D x V) * zadnje pocinkane stranske stene se lahko odstranijo. (dolžina nadgradnje, približno 2.560 mm) (± 46 kg) * orodjarna omara, pocinkana, integrirana v poševno "gooseneck" prikolico (± 47 kg) * 4 pari WADER žepov za zabojnike na tovorilni površini za 20', 2x 20', 40' ali 45' zabojnik (± 40 kg) * 7 parov žepov za stranske stene, približno 100 x 50 mm

Stanje: novo, največja dovoljena obremenitev: 33.865 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Izpisek opreme Gooseneck prikolica * s poševnimi robovi spredaj, približno 45° in s poševnim zadnjim delom, približno 750 mm x 10° * 3 pari pritrdilnih obročev (LC 5.000 daN) * trda lesena obloga, debeline približno 30 mm Tovorilna ploščad * v dvojni izvlečni izvedbi s poševnim zadnjim delom, približno 500 mm x 8° * 6 parov pritrdilnih obročev, ki se zlagajo navzven (LC 5.000 daN) * 4 pari pritrdilnih obročev, ki se zlagajo navzven (LC 10.000 daN) * 1 par pritrdilnih obročev, nameščen vodoravno na sprednji strani tovorilne ploščadi (LC 10.000 daN) * 1 vmesna miza, približno 250 mm * trda lesena obloga, debeline približno 48 mm, nad osmijo obloga iz valjane pločevine * izrezi v zunanjem okvirju tovorilne ploščadi za obešanje napenjalnih trakov (LC 2.000 daN) Osi * BPW osi in vzmetenje, vse osi hidro-mehansko sinhronizirane * maksimalna tehnična obremenitev osi: 12.000 kg na os * zračno vzmetenje z ventilom za dvig in spuščanje Ljdpfx Aozlwm Nog Ejaf * orodje za osi Pnevmatike * 245/70 R 17.5, indeks nosilnosti (146/146 F) * proizvajalec po naši izbiri Podporne noge * JOST podpore (mehanske) z dvostopenjskim menjalnikom za približno 24 t dvigalne nosilnosti (približno 50 t preizkusne nosilnosti) Zavorna sistem * v skladu z direktivami EU, z EBS-E (2S2M) brez priključnih kablov do vlečne enote Barvanje * vrhunsko in dolgotrajno protikorozijsko zaščito standardno kroglično peskane jeklene konstrukcije zagotavlja dvokomponentna (2K) temeljno prevleka s cinkovim prahom * vrhunska dvokomponentna (2K) * zaključna barva, enobarvna, v RAL 3002, karminsko rdeča * zadnji del je metaliziran in pobarvan v RAL 9010 (čista bela) * metalizirano barvanje ni mogoče Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * kvalitete jekla: S355J2+N/S355MC (meja tečenja 355 MPa) S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu z direktivami EU * razsvetljava 24 voltov ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX na sprednji priključni letev z vtičnicami 24N, 24S in 15-polno * priključki v skladu s standardom ISO. 24N ISO-1185, 24S ISO-3731, 15-polni ISO-12098 Vključno z naslednjo dodatno opremo * 2 palčni kraljevi člen (King pin) * pocinkana jeklena sprednja stena, približno 400 mm visoka * rumeno-rdeči zračni spojniki na pocinkani sprednji priključni letvi * 4 kosi zavorne podloge z nosilcem na sprednji steni (± 5 kg) * nosilec za rezervno kolo pred sprednjo steno * elektro-hidravlična enota (± 45 kg) * naknadno usmerjanje od spredaj in zadaj s pomočjo kabelskega daljinskega upravljanja, upravljanje z gumbi, z nadzorom osi (brez vgradnje v vlečno enoto) * nosilec na zadnjem delu gooseneck prikolice za aluminijaste nakladalne rampe * evropski reflektorski znaki (rdeče-rumeni) na zadnji strani prikolice * rumeno reflektorsko trakom v skladu z direktivami EU, stransko, na izvlečni strani in na zadnji strani prikolice * na gooseneck prikolici in na zadnji plošči, na levi in desni strani, nosilec za opozorilne table, vključno z vtičnico * priključna letev za aluminijaste nakladalne rampe na zadnji strani vozila * nosilec za okroglo rotacijsko luč na zadnji strani prikolice * pocinkane zložljive podpore pod poševnim delom tovorilne ploščadi * zaščitnik blatnikov na zadnji strani prikolice * navodila in opis na USB-ključu * nalepka za omejitev hitrosti 80 km/h na zadnji in na obeh stranskih straneh * manometer za obremenitev osi za ugotavljanje obremenitve osi, vključno s diagramom obremenitve.

Stanje: novo, največja dovoljena obremenitev: 46.800 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Na naši spletni strani najdete naš celoten nabor vozil, ki so na voljo takoj ali v kratkem roku. Izbor iz opreme: Celotna oprema na zahtevo. "Labodje vrat": * "Labodje vrat" s poševnimi robovi spredaj, približno 45° in z zadnjo poševnostjo približno 750 mm x 10° * 3 pari pritrdilnih obročev (nosilnost 5.000 daN) * Prevleka iz trdega lesa, debeline približno 30 mm Nosilna plošča, raztegljiva različica: * z zadnjo poševnostjo približno 1.000 mm x 8° * 5 parov pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 5.000 daN) * 3 pari pritrdilnih obročev, z zunanjim mehanizmom za zlaganje (nosilnost 10.000 daN) * 1 par pritrdilnih obročev, nameščen vodoravno spredaj na nosilni plošči (nosilnost 10.000 daN) * Vrezanine v zunanjem okvirju nosilne plošči za pritrditev zategovalnih trakov (nosilnost 2.000 daN) * Prevleka iz trdega lesa, debeline približno 48 mm, nad osmi protizdrsna prevleka. Osi: * Osi in vzmetenje BPW * Prva os je fiksna, vse ostale osi pa so hidravlično-mehansko sinhronizirane * Tehnična obremenitev osi: 12.000 kg na os * Zračno vzmetenje z ventilom za dvigovanje in spuščanje * Orodje za osi * Pnevmatike * 245/70 R 17.5 3PMSF * Indeks obremenitve (146/146 F) * TPMS: Sistem za nadzor tlaka v pnevmatikah, v skladu s standardom ECE R 141 Podporne noge * Podporne noge JOST (mehanske) z 2-stopenjsko prestavo za približno 24 t dvigalne nosilnosti (približno 50 t preizkusne nosilnosti) Zavorna naprava * v skladu s predpisi EU z EBS-E (4S3M) Barvanje * Celotna jeklena konstrukcija, avtomatsko obdelana s peščanjem po varjenju * Drugo peskanje s korundom za optimalno oprijemljivost prevlečnega sistema * HRM-metalizacija celotnega šasije vozila s pomočjo ZINACOR 850 (85 % cink/15 % aluminij) za zagotavljanje najboljše korozijske zaščite * Končno barvanje z 2 plastmi 2K lakom * enobarvno, v barvi RAL 3002 Karminrot, v skladu s sistemom RAL 841GL * Platišča v srebrnosivi barvi. Zadnji del metaliziran in pobarvan v barvi RAL 9010 (čista bela) * Metalizirano barvanje ni mogoče * Barvna prevleka preizkušena s testom solne megale v skladu s standardom ISO 9227-NSS * Zapiranje votlin s specialnim voskom Jeklena konstrukcija * iz visoko trdnih finozrnatih jekel * Kakovost jekla: S355J2+N/S355MC (meja tečenja 355 MPa), S690QL/S700MC (meja tečenja 690 MPa) Električni sistem * v skladu s predpisi EU Osvetlitev * 24 Volt ASPÖCK-NORDIK (ASS3) * Vse LED stranske gabaritne luči utripajo skupaj s smerokazom * ASPÖCK-UNIBOX na priključni letev spredaj s vtičnicami 24N, 24S & 15 polna * Priključek v skladu z ISO. 24N ISO-1185 24S ISO-3731 15 polna ISO-12098 Ledozk S Dmopfx Ag Eoaf Vključno z naslednjo dodatno opremo: * 2-palčni kraljevi priklop * Pocinkana jeklena sprednja stena, približno 400 mm visoka * Elektro-hidravlična agregat (± 45 kg) * Pomik sprednje in zadnje osi s kabelskim daljinskim upravljanjem preko tipk, z nadzorom ene osi (brez vgradnje v centralno mazalno enoto) * 1 par potopljenih pritrdilnih obročev vzdolž centralnega nosilca zadaj v poševnem delu (nosilnost 10.000 daN) (± 3 kg) * Na "labodjem vratu" aluminijaste bočne stene in zadnja stena, vstavljivi, približno 2.440 x 400 mm (D x V) * Zadnje pocinkane vstavne ograje je mogoče odstraniti. (dolžina nadgradnje približno 2.560 mm) (± 46 kg) * Orodje, galvanizirano, integrirano v poševni del "labodjega vrata" (± 47 kg) * 3 pari WADER žeepov za kontejnerje na nosilni plošči za 20' (30?) ali 40'? kontejner (± 30 kg) * 6 parov žeepov za vstavne ograje, približno 100 x 50 mm, v zunanjem okvi

Stanje: novo, največja dovoljena obremenitev: 98.290 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, You can find our entire range of vehicles that are immediately and soon available on our website. Extract from the equipment list. Full equipment details available on request. Gooseneck: * MAX810-neck-V-30-2.70-2{DSR 2 700/ASH 1300->1400} * Gooseneck hydraulically liftable/lowerable as well as removable. Length approx. 3,650 mm * Truck hydraulic connection with flow controller (20 l/min), * incl. gallows for suspension of supply lines, tractor unit (SZM) tank must hold at least 80 l, with MAX Trailer coupling pieces; otherwise, coupling pieces to be provided by the customer ex works. * For tractor units: 6 x 4 or 8 x 4 Loading Platform MAX810-6-A-11.00-17.5-1.50-2.75-PA-X * 6-axle extendable loading platform with pin-lug coupling at the front and approx. 500 mm x 8° chamfer at the rear. * Length: approx. 11,000 mm * Technically extendable by: approx. 7,700 mm * Axle spacing: approx. 1,500 mm * Hydraulic coupling bolt. Pendulum axle 2-axle front running gear, pendulum axle * All axles are hydromechanically forced steered. * MAX810-chassis-PA-X-F-2-17.5-1.50-2.75 pin-lug coupling front and rear. * Length: approx. 2,970 mm, chassis width: approx. 2,750 mm * BEKA-MAX central lubrication for a 2-axle running gear with standard grease NLGI-2 Lsdpfezbfuhex Ag Ejaf * Extendable widenings of approx. 230 mm per side for a 2-axle running gear. (± 27 kg) PENDULUM AXLE 6-AXLE LOADING PLATFORM, PENDULUM AXLE * All axles hydromechanically forced steered. * Hose burst valve on the axle compensation cylinder with automatic reset function. * Hydraulic cylinders with shut-off valves and pre-pin for securing in raised position. * Technical axle load: 13,740 kg each (30 km/h) * Hydraulic axle compensation. TYRES * 24 x manufacturer of our choice (M+S) 245/70 R17.5 * Load index 143/141L (146/146F) * TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Final coating of the axles * Painted with two coats of single-colour 2-component paint in DB7350 nova grey. * PAINTING Complete steel structure automatically blasted with shot blasting system after welding. * Second blast processing with corundum for optimal adhesion of the coating system. * HRM-metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection. * PAINTING Trailer carmine red (RAL 3002) Including the following accessories * Gallows with winch for spare wheel at the front of the gooseneck. * 3.5 inch king pin * Steel front wall approx. 400 mm high. * Plug-in ALU side boards and rear wall on the gooseneck, approx. 400 mm high, anodized version. * Control lever on the gooseneck protected by a foldable cover. * Lighting of the controls on the gooseneck with on/off switch. * One 7-pin socket left and right rear on the gooseneck for the warning sign. * Load gauge on the gooseneck for axle load determination on the running gear at front and rear * BEKA-MAX central lubrication for a gooseneck with standard grease NLGI-2. * Hydraulic connections from the gooseneck to the low bed with screw couplings. * Access possibility on the gooseneck. * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 HP) at 3000 rpm, emission level: EU Stage V, max. hydraulic pressure: 280 bar, max. flow: 21 l/min, installation on the gooseneck. * Hydraulic oil tank 100 L, frame hot-dip galvanized (± 480 kg) * Hydraulic connection lines between powerpack and plug-in plate on the gooseneck. * Radio remote contr

Stanje: rabljeno, lastna masa: 10.350 kg, največja dovoljena obremenitev: 37.650 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 10/2018, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: oranžna, Leto izdelave: 2018, obratovalna teža: 10.350 kg, Oprema: ABS,

Stanje: novo, lastna masa: 9.600 kg, največja dovoljena obremenitev: 53.400 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.400 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 1.340 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: siv, Oprema: ABS, Platform area: - Platform with approx. 30 mm thick hardwood flooring - 10 pairs of folding lash rings (outward folding) Landing legs: - JOST landing legs with 2-speed gearbox, 24 t lifting capacity Axles and tyres: - BPW axles, technical capacity 10,000 kg per axle; first axle fixed, all other axles hydro-mechanically forced-steered, mounted on turntables - Air suspension with raise/lower valve - Axle tools included - Tyres: 385/65 R22.5 Lajdpfxsrq Dlfe Ag Eef Braking system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: - S355J2+N / S355MC - S690QL / S700MC Electrical system: - Electrical system according to EU regulations, 24 Volt lighting - ASPÖCK-UNIBOX on the front connection rail with 24N, 24S and 15-pin sockets - Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame is ensured by a 2-component zinc-dust primer - High-quality 2-component topcoat, single-colour in Nova Grey - Rear section metallized and painted in RAL 9010 Accessories included: - Platform with approx. 30 mm thick hardwood flooring - 2" king pin - One galvanized steel front wall approx. 1,200 mm high, EN12642-XL - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks with holders on the front wall - Storage for 1,000 mm plug-in stanchions in the rear central beam - On the gooseneck and rear panel, left and right, a mounting bracket for warning signs with socket - Remote steering from front and rear, operated via cable remote control with push-buttons; with axle tracking control - Electro-hydraulic power pack - White reflective tape as per EU regulations along the side of the trailer, red at rear - 12 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the load bed - European reflective plates at the trailer rear - One bracket for a rotary beacon at the rear of the trailer - One mudflap at the trailer rear - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard NLGI-2 grease and removable protector for the pump - TPMS tyre pressure monitoring system: - The towing vehicle must be capable of transmitting and displaying these data for correct readout - Lift axle on the front axle, automatically controlled by TEBS E in accordance with current axle load and trailer loading status - Radio remote control for the remote steering in addition to the cable remote, with indicator lamps on the receiver for axle tracking control - 5 pairs of crosswise stanchion pocket strips on the bed for 100 x 50 mm plug-in stanchions - 80 km/h speed stickers at rear and both sides - Adjustable access ladder mounted left and right in direction of travel - 2 reversing lights mounted at the rear panel - Load gauge for determining axle loads, including load diagram - HRM metallization of the outer frame: complete steel structure shot-blasted, then all designated visible areas hot metalized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Stanje: novo, lastna masa: 15.550 kg, največja dovoljena obremenitev: 47.450 kg, skupna masa: 63.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator dipper stick - Pneumatic locking with conical locking bolts and reinforced lock positions - Hardwood covering on the loading platform bevel Ramps: - 1 pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm - Ramps with hardwood covering - Hydraulically folding ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward - Square climbing cleats 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle lift-steered, all other axles forced-steered with hydromechanical system - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - Tyres 235/75 R 17.5, twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS sensors installed in all wheels including spares Accessories included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic power pack for hydraulic operations, excluding hydraulic winches - Parking position on gooseneck for warning boards when not in use - 1 spare wheel - On the gooseneck: 1 pair of removable side aluminium drop sides, approx. 400 mm high, anodised - On the gooseneck: 1 removable rear aluminium drop side, approx. 400 mm high, anodised - Above the gooseneck: approx. 40 mm thick hardwood floor, chequer plate above king pin - 2" king pin - Guide plate on gooseneck for fifth wheel, approx. 500 mm wide Lodpsk Aht Uofx Ag Esaf - 4 wheel chocks - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Extensions (galvanised) extendable by approx. 230 mm per side - Wheel recesses with square climbing cleats - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering at front and rear via cable remote control, with single track monitoring of axles - 1st axle with automatic lift axle function - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, additionally to cable remote, with 2 indicator lights on the receiver as single track monitoring - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for revolving beacon

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Ledpsl Sl Izjfx Ag Ejaf Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Ledpfx Ajhlz S Neg Esaf Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 38.500 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Load Area: - Extendable loading area with rear taper approx. 1,000 mm x 8° Ledpfx Ajup U Hzog Esaf - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with square climbing strips 15 x 15 mm, including lower extensions - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel as well as protruding into the loading area for parking excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of lashing rings, installed flat at the front of the load area (LC 10,000 daN) - 5 pairs of folding lashing rings on the outside (LC 5,000 daN) - 2 pairs of folding lashing rings on the outside (LC 10,000 daN) - 2 pairs of lashing rings in the dipper stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the load area for securing straps (LC 2,000 daN) - Incl. three-part removable galvanized covers over the wheel recesses – max. point load 3.5 t / pc. Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood surfacing - Ramp with hydraulically folding ramp sections, hydraulic lifting gear, and hydraulically adjustable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tool kit - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Mounts for warning signs left and right at the gooseneck and at the rear, each with socket - One spare wheel - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized front connector strip - 4 wheel chocks - Galvanized, extendable outriggers approx. 230 mm per side - Galvanized folding supports beneath the loading area bevel - Rear trailer bracket for rotating beacon - Cover plates for bridging the gap between ramps and load area - White reflective tape to EU regulations, sides and on extensions; rear in red - Electro-hydraulic unit installed at the rear beneath the loading area - Ramp control valves mounted on right trailer side - European reflective panels (red-yellow) on rear of trailer - Four extendable warning boards, approx. 423 x 423 mm, with position light - Bracket for rotating beacon on warning boards - Removable ALU side boards and rear board on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (structure length approx. 2,560 mm) - 2 pairs of WADER container pockets in loading area for 20ft or 30ft container - 3 pairs of socket pockets for stakes 100 x 50 mm in outer frame of loading area - Removable, galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm spaced every 200 mm on outer frame at loading bevelling - Painted sand layer on chequer plates of the gooseneck and loading area for anti-slip protection - 80 km/h speed stickers rear and both sides - Load manometer for axle load measurement, including load chart.

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Lodpfok Ahugox Ag Eeaf Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: novo, lastna masa: 12.000 kg, največja dovoljena obremenitev: 54.000 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable load area: - Extendable loading platform with rear bevel approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the platform (LC 10,000 daN) - Cut-outs in the outer frame for tensioning straps (LC 2,000 daN) - Hardwood floor approx. 48 mm thick, checker plate over the axles Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Brake system: - WABCO brake system according to EU regulations with EBS-E (4S3M) Steel construction: - High-strength fine-grained steel chassis Axles and tires: - BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve - Axle tool kit - TPMS tire pressure monitoring system to ECE R 141 - Tires: 245/70 R 17.5 3PMSF Accessories included: Lasdeykpbkepfx Ag Esf - 2" kingpin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - 4 wheel chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Forced steering, operated from front and rear using a cable remote control with push buttons, with single-track monitoring of axles - European reflective panels (red-yellow) on trailer rear - White reflective tape in accordance with EU regulations on sides and on extension, rear red - Mountings on gooseneck and rear left/right for warning signs, incl. socket - Galvanized extensions, pull-out approx. 230 mm per side - Mount for rotating beacon at rear of trailer - Galvanized folding supports under the rear slope of the loading area - Mudflap at the rear of the trailer - Manual and documentation on USB stick - BEKAMAX (Pico) centralized lubrication system with standard grease NLGI-2 and removable pump guard - Removable ALU side boards and rear board on gooseneck, approx. 2,440 x 400 mm - Rear removable, galvanized stanchions (superstructure length approx. 2,560 mm) - INOX toolbox 1,350x400x400 mm on gooseneck - Note: toolbox covers oil filler cap - 4 pairs of WADER container pockets in the loading area for 1x 20ft, 2x 20ft, 1x 40ft or 1x 45ft container - 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame - Sliding mounting bar for ALU loading ramps at the rear of the vehicle - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the sloping rear section - Lift axle on front axle with control via TEBS-E depending on current axle load and load condition - Four extendable warning boards, approx. 400 mm, size approx. 423 x 423 mm, each with position light - Mounting for rotating beacon on the warning boards - Radio remote control for forced steering, additionally to cable remote, with indicator lights on receiver for single-track monitoring - Checker plate surfaces on gooseneck and loading area with painted-on sand coating for slip resistance - 80 km/h speed stickers on rear and both sides - Load gauge for axle load measurement, incl. load diagram

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control Lasdsya E A Njpfx Ag Esf - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5 3PMSF, barva: siv, Oprema: ABS, Swan neck: - Swan neck with front corners beveled at 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm hardwood flooring Extendable load area: - Extendable load area with rear chamfer approx. 1,000 mm x 8° - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat lashing rings at the front of the load area (LC 10,000 daN) - Cut-outs in the external frame of the load area for attaching lashing straps (LC 2,000 daN) - Approx. 48 mm hardwood flooring, over the axles with checker plate covering Axles and Tires: - BPW axles and suspension, 2 fixed axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear or manually - Air suspension with lifting and lowering valve - Axle tools - 235/75 R 17.5 tires, 3PMSF Braking system: - WABCO braking system as per EU regulations with EBS-E (2S2M) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Accessories included: - One spare wheel with holder in front of the front wall - 2'' king pin - One galvanized steel front wall, approx. 400 mm high Lasdpfx Ajuqlmneg Eof - Yellow-red air couplings on the galvanized front connection rail - 4 wheel chocks with holder at the front wall - Rear light bracket at the rear of the trailer - Mounting points at the rear area of the swan neck for ALU loading ramps - Galvanized folding supports under the chamfer of the load area - Cover plates to bridge the gap between ramps and load area - White reflective tape according to EU standards on the sides, red at the extension and rear - Electro-hydraulic unit at the rear, under the load area - Bracket for warning panels left and right on the swan neck and ramps, including power socket - Ramp control valves mounted on the right-hand side of the trailer - One mud flap at the rear of the trailer - Manual and documentation on USB stick - On the swan neck aluminum side walls and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm, with position light - 3 pairs of WADER container pockets in the load area for a 20ft, 30ft, or 40ft container - 6 pairs of stake pockets 100x50 mm in the external frame of the load area - Galvanized extensions, extendable by approx. 230 mm per side - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the chamfered area of the load area - Anti-slip sand layer painted on the checker plate above the king pin and load area - Mounting for beacon on the warning panels - European reflective plates (red-yellow) at the rear of the trailer - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads, including load chart - HRM metallization (High Resistance Metallisation) of the external frame - Complete steel construction shot-blasted, then the defined visible surfaces finished hot-metallized with ZINACOR 850 (zinc 85% - aluminum 15%)

Stanje: novo, lastna masa: 7.900 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, obratovalna teža: 7.900 kg, Oprema: ABS, Swan Neck: - Swan neck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood decking Loading Area: - Loading area with rear chamfer of approx. 1,000 mm x 8° - Recess in the chamfer and encroaching into the loading area for receiving the excavator bucket stick approx. 2,900 x 750 x 210/290 mm - Cut-outs in the external frame of the loading area for attaching tension straps - Hardwood decking approx. 48 mm thick, over the axles with tread plate covering Ljdpjunrapefx Ag Ejaf Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles and suspension, 2 axles rigid, 1 axle self-steering t- Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raising and lowering valve - TPMS tyre pressure monitoring system compliant with ECE R 141 - Tyres 235/75 R 17.5 Paintwork: - Complete steel structure blasted automatically by wheel blast machine after welding - Second blasting with corundum for optimal adherence of the coating system - Final coating: two layers of 2K top coat, solid colour in RAL MB 7350 Novagrau - Rims painted silver - Rear section metallised and coated in RAL 9010 (Pure White) - Cavity sealing with special wax Electrical System: - Electrical system according to EU standards, 24 volt ASPÖCK-NORDIK (ASS3) lighting - ASPÖCK-UNIBOX at front connection rail with sockets 2x 7-pin & 1x 15-pin Included Accessories: - Multiple lashing positions - 2" king pin - One galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on galvanized front connection rail - 4 wheel chocks with holders mounted on the front wall - Receiver at rear of swan neck for ALU loading ramps - Galvanised folding supports beneath rear chamfer of loading area - Bracket for beacon at rear of trailer - Galvanised extendable outriggers, extendable by approx. 230 mm per side - White reflector tape to EU spec at sides and rear, red at rear - Brackets for warning signs on left and right of swan neck and rear panel, including socket - ALU side boards and rear board on swan neck, removable, approx. 2,440 x 400 mm - Rear galvanised stake pockets are removable - 2 pairs WADER container pockets in loading area for 20ft container - 6 pairs stake pockets for removable stakes 100 x 50 mm in the outer frame - Adjustable hanging rail for ALU access ramps at the rear of the vehicle - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the loading area chamfer - Sand-finish anti-slip coating painted onto the tread plate on swan neck and loading area - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm with position light - Bracket for beacon fitted to warning boards - 80 km/h speed sticker rear and on both sides - European reflective signs (Red-Yellow) at the rear of trailer - Manual and operating instructions on USB stick - HRM metallisation (High Resistance Metallisation) of the external frame - Complete steel structure shot-blasted, then specified visible surfaces metallised with ZINACOR 850 (Zinc 85% - Alu 15%) hot-finished

Stanje: novo, največja dovoljena obremenitev: 36.020 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles available for immediate or short-term delivery on our website. Partial equipment listing. Full equipment details available upon request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of outward folding lashing rings (LC 5,000 daN) * 3 pairs of outward folding lashing rings (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, with checker plate covering over the axles Two-part steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating surface C40/5 (point load approx. 2.8 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections and hydraulic lifting mechanism * Maximum load per pair: 30,000 kg Landing legs: * JOST landing gears (manual) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, can be activated via reverse gear and manually * Air suspension with raise and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations with EBS-E (2S2M) without connectors to the tractor unit Steel structure: * Steel construction made from high-tensile fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final coating with 2 layers of two-component topcoat, single colour in RAL 3002 carmine red, in accordance with RAL System 841GL * Rear section metalized and painted RAL 9010 (Pure White) * Wheels in silver Including accessories: * One bracket for warning signs on both sides at the gooseneck and at the rear, including socket * 1 spare wheel holder under the loading area on the right-hand side * 2" kingpin * Galvanized steel front wall * Yellow-red air couplings on the galvanized connector strip at the front * 4 wheel chocks with holders on the front wall * 3 height-adjustable wooden planks * Galvanized folding supports under the loading area bevel * Bracket for a rotating beacon at the rear of the trailer * Height-adjustable tarpaulin frame (approx. 3,960 mm) * Galvanized front wall with tensioning mechanism for sliding curtains, height-adjustable by approx. 400 mm * EDSCHA roof, forward-sliding, on aluminium roof beam profiles (bolted with front and rear wall) * 3 pairs of sliding stakes in the loading area * Superstructure can be hydraulically widened at the rear to left and right by approx. 750 mm * Sliding roof with liftable portal carrier Ledpfx Aoy Auhujg Eeaf * Sliding tarpaulin with approx. 700 mm slack in length, with tensioning straps spaced approx. 600 mm

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: Lsdpfx Agjiu Er Ao Eeaf - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Laedpfx Agoma Hf Rs Eef Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, največja dovoljena obremenitev: 37.075 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our full stock of immediately and soon-available vehicles on our website. Ljdpjyhkqzefx Ag Ejaf Selected features listed below. Complete specification available upon request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick Load area: * Load area hydraulically raisable and lowerable after the gooseneck, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° * 6 pairs of outward-folding lashing rings (LC 5,000 daN) * 2 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tensioning straps (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), checkered plate surface above the axles Two-part steel ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections. Hydraulic lifting system, hydraulically extendable * Maximum load capacity per pair: approx. 40,000 kg Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lockout, activated by reverse gear and manually * Air suspension with lift and lower valve Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Tyres: * 235/75 R 17.5 3PMSF – Brand of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallization of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with two layers of 2K topcoat, single color in RAL 3002 Carmine Red according to RAL system 841GL * Wheels in silver-grey Included equipment: * 2" kingpin * One galvanized steel front wall, approx. 400 mm high * Grating surface in the gooseneck’s chamfer C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating surface in the load area’s chamfer C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Sand coating applied as slip protection to the checkered plates above the kingpin and loading area * Electro-hydraulic power unit under the rear of the load area * On the gooseneck: removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H). The galvanized rear stakes are removable. (Body length approx. 2,560 mm) * One electric cable winch with radio remote control, approx. 5,400 kg line pull, incl. approx. 9.5 mm steel cable, approx. 24 m long, with cable guide roller * Bolted 5 t ring for guiding the winch cable on the neck without a deflection roller * One galvanized toolbox integrated into the chamfered gooseneck, with opening for winch * Grating surface on gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for approx. 100 x 50 mm slip-in stakes in the outer frame of the loading area * Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition * 7 pairs of... [Text truncated - please provide remaining content for further translation if needed.]

Stanje: novo, največja dovoljena obremenitev: 38.140 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our full range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Gooseneck: - Gooseneck with approx. 45° chamfered front corners and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Approx. 30 mm thick hardwood flooring Loading platform: - Telescopic loading platform with rear slope approx. 1,000 mm x 8° - Between the 1st and 2nd axle, a pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece, removable, galvanized cover over the wheel recesses (W approx. 670 mm – max. point load 5 t / each) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - 4 pairs of folding external lashing rings (LC 5,000 daN) - 3 pairs of folding external lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - 235/75 R17.5 3PMSF tyres, manufacturer of our choice - TPMS – Tire Pressure Monitoring System according to ECE R 141 - Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992 - The tractor unit must be capable of transmitting and displaying these data for correct indication. Axles: - BPW axles and suspension, 2 axles fixed, 3rd axle trailing steer - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve. Axle tools Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor Electrical system: - Electrical system in accordance with EU regulations - LED lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicators - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: - Steel construction made from high-strength fine-grained steel - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: - Entire steel structure automatically shot-blasted with shot-blast machine after welding - Second blasting with corundum for optimal coating adhesion - HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% Zinc / 15% Aluminum) to ensure best corrosion protection - Final coating with 2 layers of 2K top coat, single color RAL 3002 Carmine Red. Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavities sealed with special wax Including the following accessories: - On both the gooseneck and at the rear left and right, one holder for warning boards, including socket - Spare wheel holder in front of the bulkhead (without spare wheel) - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanized connection panel at the front - Galvanized folding supports under the rear slope of the loading platform - Hardwood rear impact protection from gooseneck rear wall to loading platform - 1 pair of recessed lashing rings along the central frame at the rear in the slope (LC 10,000 daN) - On the gooseneck, aluminum side and rear walls Laodpfxsw Tpq De Ag Esf

Stanje: novo, največja dovoljena obremenitev: 47.300 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Complete equipment details available upon request. Gooseneck: * Gooseneck with chamfered front corners approx. 45° and rear chamfer approx. 750 mm x 10° Lsdpfsyvnfgsx Ag Ejaf * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area in extendable design with rear chamfer approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) * Recesses in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate flooring above the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Tyres: * Tyres 235/75 R 17.5 3PMSF, manufacturer of our choice Axles: * BPW axles, two rigid axles, two self-tracking axles, air suspension, drum brake, with lifting/lowering function * The self-tracking axles can be locked for reversing by electro-magnetic reverse lock via reverse gear or manually * Axle tools Brake system: * WABCO brake system in compliance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Premium and durable corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc dust primer * High-quality two-component (2K) topcoat, single colour, RAL 3002 Carmine Red * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the front wall (without spare wheel) * 2-inch king pin * Galvanised steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanised connection strip at the front * Mount in the rear area of the gooseneck for ALU loading ramps * Galvanised folding supports under the rear chamfer of the loading area * Holder for a beacon at the rear of the trailer * On the gooseneck and at the rear end panel, left and right, holders for warning signs including socket * TPMS tyre pressure monitoring system according to ECE R 141 * On the gooseneck, plug-in aluminium side walls and tailgate, approx. 2,440 x 400 mm (L x H). The rear galvanised plug-in stanchions are removable. (Body length approx. 2,560 mm) * Galvanised toolbox integrated into the chamfered gooseneck * 3 pairs of WADER container pockets recesses in the loading area for a 20' (30') or 40' container * Sliding hooks for aluminium loading ramps at the rear of the vehicle * 6 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading area * Galvanised extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control via TEBS E depending on the current axle load and current loading status * 2 LED reversing lights mounted on the rear end panel * 2 pairs Ferry-

Stanje: novo, največja dovoljena obremenitev: 37.075 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our full selection of vehicles available for immediate or short-term delivery on our website. Extract from the equipment list. Complete equipment details available on request. Gooseneck: * Gooseneck with beveled corners at the front approx. 45°, and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° * 6 pairs of lashing rings, foldable outward (LC 5,000 daN) * 2 pairs of lashing rings, foldable outward (LC 10,000 daN) * 1 pair of lashing rings, foldable inward at the central beam front (LC 10,000 daN) * Cutouts in the outer frame of the platform for attaching tension belts (LC 2,000 daN) * Grating floor C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over axles with checker plate covering Two-part Steel Ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm with grating floor C40/4 (point load approx. 2.2 t on an area of approx. 20 x 20 cm) Lasdpfx Asyhkrrjg Ejf * Ramp with hydraulically folding and unfolding ramp segments * Hydraulic lifting device, hydraulically movable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated by reversing gear or manually * Air suspension with lift and lower valve Braking System: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Tyres: * Tyres 235/75 R 17.5 3PMSF. Brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallization of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final paintwork with 2 coats of 2-component topcoat, solid color in RAL 3002 Carmine Red, according to RAL system 841GL * Rims in silver grey Included Accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Grating floor on gooseneck chamfer C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating floor on platform chamfer C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Electric-hydraulic power pack underneath the rear of the platform * On the gooseneck, aluminum side panels and rear panel, plug-in, approx. 2,440 x 400 mm (L x H). The rear galvanized stanchions are removable. (Superstructure length approx. 2,560 mm) * One electric winch with radio remote control, approx. 5,400 kg pulling capacity, incl. approx. 9.5 mm steel cable, approx. 24 m long, with cable guide roller * Bolted 5 t ring for anchoring winch cable on the gooseneck without pulley * One galvanized toolbox, integrated in the beveled gooseneck with an opening for winch passage * Grating floor on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm on the outer frame of the platform * Lift axle on the front axle with TEBS E control based on current axle load and loading status * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Stanje: novo, največja dovoljena obremenitev: 39.720 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of vehicles, including immediately and short-term available units, can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck * With beveled front corners, approx. 45°, and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * Extendable loading area version * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of lashing rings laid flat at the front of the loading area (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Landing legs * JOST (mechanical) with two-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Axles * BPW axles, two fixed, two self-steering, with drum brakes * Air suspension with raise/lower function * Self-steering axle with electromagnetic reverse lock, activated by reverse gear or manually * Tyres: 205/65 R 17.5 Braking system * Wabco braking system meeting EU regulations with EBS-E (4S3M), without interconnection lines to the tractor unit Steel Construction * Made from high-tensile fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, long-lasting corrosion protection for the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer * High-grade, single-color two-component (2K) topcoat in RAL 3002 Carmine Red * Rear section metallized and finished in RAL 9010 (Pure White) * Wheels in silver Accessories included * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Spare wheel holder in front of the front wall * Yellow-red air couplings on galvanized front connection rail * 4 wheel chocks with holder on the front wall * Rear section of the gooseneck with mounting for aluminium ramps * Galvanized folding supports under the rear bevel of the loading area * Bracket for a beacon on the trailer’s rear * Yellow reflective tape on the sides, extension, and rear, in compliance with EU regulations * Holders for warning signs with socket on left and right of gooseneck and rear panel * TPMS tire pressure monitoring system according to ECE R 141. Data transfer to the towing vehicle is via the standardized EBS interface per ISO 11992; for correct display the towing vehicle must be able to receive and display the data * On the gooseneck: clip-on aluminium side and rear panels, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * One galvanized toolbox integrated into the beveled gooseneck * 6 pairs of WADER container pockets in loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container * Sliding brackets for aluminium ramps at the vehicle’s rear * 7 pairs of stake pockets for removable stakes, approx. 100 x 50 mm in the outer frame of the loading area * One galvanized transverse holder under the loading area * Galvanized, extendable outriggers for widening by approx. 230 mm per side Lajdpsu Sd U Uofx Ag Ejf * Lift axle on the front axle controlled by TEBS E depending on current axle load and loading condition * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Stanje: novo, konfiguracija osi: 3 osi, Leto izdelave: 2026, Razpolagamo z vso evropsko dokumentacijo! Lajdpfsqx Nfgjx Ag Eef Prikolice lahko dostavimo pod pogoji FOB, EXW, CPT, CFR ali CIF. Če ste zainteresirani, vas prosimo, da nas kontaktirate.