Müller Traktorji (Vlečni Traktorji) nakup rabljenega (278)

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: 3-in-1: Suitable for hooklift containers, skip containers, and as a low loader ----Brakes: * EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 tonne axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * TPMS (Tyre Pressure Monitoring System), display on truck via EBS signal (no truck-side installation required) * LED rear lights 12/24V * 15-pin power connector ----General Attachments: * Toolbox made of powder-coated sheet steel Bjdpfx Ajl Tld Isn Iedc * Spare wheel carrier basket, right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffers * Folding A-board at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer rails to guide roll-off containers * Steel floor with roller recesses in the bogie area * For hooklift container transport, container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking system and mechanical plug-in stop angles at the front of the track * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 repositionable skip locators for lateral centering of the skips, front 4 locators plug-in with swinging stop * Weld seam as anti-slip surface in the ramp area * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for hooking in securing elements for positive and non-positive locking of skips, 4 cloverleaf-type lashing bars per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t lashing eyes per side flush-mounted in the outer frame ----Ramps: * Aluminium approach ramps (10.6 t per pair), 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment at rear) ----Paintwork: * Reflective contour tape on sides & rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Permissible gross weight technically up to 20,000 kg * New vehicle, never registered, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Type Towing Eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of fine-grain steel ----Tipper Platform: * Mesh hooks on sides and rear located at the central locking mounts, plus 2 on the front wall * Steel pallet two-way tipping body, front wall fixed, made of smooth plate; continuous collapsible sidewalls (without center posts), with drop side spring lifters and manual central locking for tilting * Rear stanchions bolted * Steel rear wall slid in front of the ramps * Each corner with 1 x 5 t lashing point; 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm floor made of fine-grain steel Bdsdpfx Astr Sucon Iec ----Ramps: * Two-piece mechanical grating drive-up ramps with aluminium tip section 2,150 + 1,300 mm x 600 mm (can be slid together manually up to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical stabilizer legs, and ramps hot-dip galvanized * Axles, springs, air tanks, towing eye, and landing gear painted in black * Sidewalls and platform in RAL 9010 pure white * Paint finish of sidewalls and tipper platform available in RAL color of choice at extra charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes Bedpfxetr St Us An Iedc ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange-Type Towing Eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of fine-grain steel ----Tipper Platform: * Mesh hooks on sides and rear located at the central locking mounts, plus 2 on the front wall * Steel pallet two-way tipping body, front wall fixed, made of smooth plate; continuous collapsible sidewalls (without center posts), with drop side spring lifters and manual central locking for tilting * Rear stanchions bolted * Steel rear wall slid in front of the ramps * Each corner with 1 x 5 t lashing point; 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm floor made of fine-grain steel ----Ramps: * Two-piece mechanical grating drive-up ramps with aluminium tip section 2,150 + 1,300 mm x 600 mm (can be slid together manually up to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical stabilizer legs, and ramps hot-dip galvanized * Axles, springs, air tanks, towing eye, and landing gear painted in black * Sidewalls and platform in RAL 9010 pure white * Paint finish of sidewalls and tipper platform available in RAL color of choice at extra charge ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 8.870 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flanged Drawbar Eye: * Height-adjustable drawbar by 300 mm * 40 mm flanged drawbar eye ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding rear supports * Plastic quarter mudguards * Plastic toolbox mounted front right on the bulkhead ----Electrics / Lighting: * RDÜ tire pressure monitoring system * LED lighting ----Loading Area: * Loading platform length: 6.27 m * Suitable for container transport * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal profile steel, foldable with drop side spring lifter * Steel tailgate, insertable between ramp holders; stowable inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Each front and rear corner fitted with 1 x 6.3 t lashing point * Various holes in bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical drive-on ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be retracted to 20 mm height) * Rear approach angle approx. 860 mm ----Tyres: Bdodpsrvvfwsfx An Ioc * Tyres: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paint Finish: * Hot-dip galvanized chassis, drawbar, bulkhead, tailgate, rear stanchions, and ramps * Sideboard paint finish in RAL 9010 pure white * Painting of side walls in another RAL color possible at extra cost ----Information: * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Availability: * Available from CW (calendar week)

Stanje: rabljeno, največja dovoljena obremenitev: 6.000 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, prva registracija: 04/2026, Oprema: ABS, * Müller Mitteltal KWH 8.8 ML Cable Transport Trailer * LIKE NEW and available * Reference for inquiries: 11652 * TPMS Tire Pressure Monitoring System * EBS brake system, drum brake, BPW axle, parabolic springs * Support winch at front, spring-assisted square tube supports at rear with base plate, safety locking pins for multiple support heights * Drawbar with 40 mm towing eye (height-adjustable in mm) * 15-pin electrical connector * LED lighting * 315/80 R 22.5 tyres, solid steel fenders * Swivel-mounted cable reel assembly * Steel drum shaft with 76 mm diameter, centering and rotating ends * 1 pair of step-tapered polyamide centering cones * For reel diameters Ø 800–3,000 mm x (1,700 mm width between reel arms) * With clamp lock for securing the reel at the end of load arms and central claw lock for securing the cable reel assembly to the chassis * Motor-hydraulic, actuated pull and push cylinders with pipe rupture protection. Control valve with auto-centering neutral position, pressure relief valve, and lowering throttle. NW 13 hydraulic system connectors, hoses, and pipes included. * Hydraulically driven reel motor with oil motor, valves, and rubber-coated drive rollers (adjustable). Hydraulic speed regulator and brake for reel drive. * Includes hydraulic pump unit – Hatz 1B30 Silent diesel engine with hand starter, 6.5 HP (150 bar), pressure supply selectable via connection change: truck hydraulics or pump unit * Toolbox approx. 500 x 350 x 400 mm * Hot-dip galvanized chassis with drawbar * Advert space integrated in side guard, exterior polyester-coated in RAL white * ----like-new condition (only used for one project) * ---- * Financing available from our partner banks with or without down payment, balloon payment and different terms possible. Ask us for a quote! * We are an official Müller Mitteltal trading partner! * Lease-purchase example from our partner FM LeasingPartner: starting from just €595/month net, 60 months term (no down payment, €0 final payment). * Ask us for a quote! ---- * Our business hours: * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside business hours, appointments by arrangement * Languages spoken: German, English, Russian, Polish, French Bdjdpfoy R Hx Usx An Isc ----

Stanje: rabljeno, največja dovoljena obremenitev: 30.700 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2002, Oprema: ABS, * MüllerMitteltal nizkopodni priklopnik s 4 osmi T40 * 2x krmiljeni vrtljivi osi Bdodpfx Aneyuri Es Isc * Nemška prikolica * pero * hidravlično pomične rampe / levo-desno * deljene preklopne rampe * možnost razširitve * ABS * BPW osi * 40 t * lastna teža: 9300 kg * osne obremenitve = 10 t na os * popolnoma funkcionalen * pnevmatike v redu

Stanje: rabljeno, največja dovoljena obremenitev: 6.940 kg, skupna masa: 10.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/2018, naslednji pregled (TÜV): 11/2026, dolžina tovornega prostora: 5.360 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 350 mm, skupna širina: 2.550 mm, Oprema: ABS, Equipment: * 40 mm jaw coupling * height-adjustable towing eye * drop-down side panels * storage box * removable tailgate * towing eyes * BPW axles * galvanized Other information: * 1 previous owner * German first delivery * Downrated from 11.9 t to 10.0 t without technical modification Since 1972, your reliable partner for all things automotive and commercial vehicles in 28832 Achim at Bremer Kreuz. NutzfahrzeugZentrum Behnke constantly stocks around 200 vehicles from the fields of vans, commercial vehicles, and construction machinery! Bedey Si Etopfx An Ijdc We continuously offer attractive financing solutions at favourable special rates. If you are interested, we will be happy to provide you with an individual quote! Trade-in of your commercial vehicle/construction machinery is welcome. If a new TÜV inspection is desired, we will gladly provide you with an offer from our partner workshops. Our offer generally does NOT include a new TÜV inspection. Delivery of your "new" commercial vehicle is possible through our external partners for an additional fee. The information provided in advertisements, on the internet, on price tags and in images are non-binding descriptions and do not constitute guaranteed features. The seller accepts no liability or warranty for typographical or data transmission errors. Listed equipment must be checked separately if necessary. Subject to errors and prior sale.

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes switched to the first axle via EBS (no installation required on the truck side) * Rear axle as self-steering axle with electro-pneumatic steering lock * Locking of the self-steering axle from the driver's cab for maneuvering purposes, controlled via EBS (no installation required on the truck side) ----Suspension: * Air suspension with lifting/lowering device and Ride-to-Return valve ----Electrics / Lighting: Bsdpjq Euakjfx An Isdc * Smart Board mounted on the trailer as an information tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket at rear for extended length lighting * Side marker lights with indicator signal control * Tyre pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) ----General equipment: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages at front and rear * Swing arm as carrier for connecting cables from truck to semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with 45° chamfered front corners and front tool box made of galvanized powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high aluminium side boards (in RAL colour of choice) on the sides of the fifth wheel platform, foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on fifth wheel platform to low bed approx. 700 mm long with tread plate covering and at the end a perforated strip for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and low bed platform with 60 mm clamped wooden planks * Tear plate above the axles * 9 x mechanical folding extensions to 3 m overall width, but not in the rear slope (extension planks available with closed storage compartment across the direction of travel under the loading floor) * 3 mounting shafts under the fifth wheel platform for storage of optional aluminium loading ramps or wooden planks for wheel well coverings ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame angled at 45° with hole pattern for lashing points (2 t lashing capacity per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings each side recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the drop, 1 x above the centre axle next to the longitudinal beam) Low loader platform: * 3 x 13.4 t lashing rings each side on the outer frame (1 x beginning of the drop on the fifth wheel platform, 1 x beginning of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings each side (1 x between front wheel well and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings each side bolted to the outer frame of the wheel wells (2 on the front wheel well, 1 on the rear wheel well) ----Excavator arm recess: * Extended excavator arm recess from end of last fixed axle through to steering axle up to rear crossmember, continuous with

Stanje: novo, največja dovoljena obremenitev: 37.390 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Traction aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for shunting via EBS (without truck-side installation) ----Suspension: Bdsdpstpta Dsfx An Ijc * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 extra LED reversing lights * 7-pin socket at the rear for additional length lighting * Side marker lights with indicator activation * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing gears at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the headboard crossmember (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection cables from truck to semi-trailer ----Lowbed platform: * Second kingpin position * Fifth wheel platform with 45° bevelled front corners and front toolbox made of galvanised, powder-coated steel sheet, W = 2,480 mm x H = 500 mm x L = 665 mm with folding lid * Side aluminium drop sides, 400 mm high (in RAL custom colour), foldable and removable * Rear wall -150 mm- high plug-in * Rear slope on the saddle platform to the lowbed approx. 700 mm long with chequer plate covering and a perforated strip at the end for attaching aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9 x mechanical folding wideners to 3 m overall width, not in rear slope (widening planks available with sealed crosswise storage compartment under the loading area) * 3 mounting shafts under the saddle platform for the storage of either aluminium loading ramps or wooden planks for wheel well covering ----Load securing (LaSi-package): Fifth wheel platform: * Perforated outer frame, 45° angled, with hole pattern for lashings (2 t lashing capacity per tie-down point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the cranking, 1 x above the central axle next to the longitudinal member) Lowbed platform: * 3 x 13.4 t lashing rings per side on the outer frame (1 x at the start of the cranked platform, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 t lashing rings per side (1 x between the front wheel well and 1st axle, 1 x between the 2nd and 3rd axle) * 3 x 5 t lashing rings per side bolted to the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear wheel well) ----Excavator arm rest: * Extended excavator arm rest from end of last rigid axle over steering axle to end crossmember, continuous with internal reinforcing profile approx. W = 770 mm x D rear = 270 mm / D front = 170 mm * 2 x 6.4 t lashing rings per side in the exca

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Braking system: * Wabco EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes Bdsdpfjl Th Hwjx An Iec ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs - 110 mm wide - with tandem compensation unit ----Drawbar / Flange drawbar eye: Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Electrics / Lighting: * 15-pin electrical connector * LED tail lights * RDÜ tyre pressure monitoring system ----General fittings: * Jost landing gear at the front * Outboard folding supports at the rear * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood flooring * Preparation in front of the headboard for retrofitting container locks * Bolted headboard made of smooth sheet metal * Drop sides made of trapezoidal profile steel sheeting, foldable with tailboard spring assist * Steel rear wall insertable between ramps - holder for storage when not in use in front of headboard * Bolted rear stakes ----Load securing: * Perforated outer frame, approx. 45-degree angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * One 10 t lashing ring in each front and rear corner, various drill holes in the front and rear cross-members for 1.2 t lashing options * Profifix lashing rail along the longitudinal axis centre for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be collapsed to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Chassis, drawbar, headboard, rear wall, loading ramps, and folding supports hot-dip galvanized * Drop sides painted in RAL 9010 pure white * Painting of the side walls in a RAL colour available at extra cost * Axles, springs, air tanks, flange drawbar eyes and landing gear painted in a shade of black ----Information: * New vehicle with full manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex-works Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar / Towing Eye: Bdjdpfopk D D Hex An Isc * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ----Electrics / Lighting: * TPMS (tyre pressure monitoring system) * 15-pin power connector * LED tail lights ----General Attachments: * Jost landing gear at the front * Outward folding rear supports * Tool box made of galvanized steel sheet, approx. 650 x 350 x 320 mm, mounted on the right side (powder-coated black) * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Reinforcement package for drill rig transport on the chassis – loading height +20 mm * 50 mm softwood floor, clamped design * Preparation in front of the front wall for subsequent installation of container locks * Bolted smooth steel front wall * Fold-down trapezoidal-profile steel side walls with board-lift assist * Steel rear wall, slidable between ramps – storage bracket for unused position inside, in front of the headboard * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * Front and rear corners each fitted with 1 x 10 t lashing ring; multiple holes for 1.2 t lashing options in front and rear crossmembers ----Ramps: * One-piece, mechanical grate ramps with spring system for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm gap) * Rear access angle approx. 860 mm ----Tyres: * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ----Paintwork: * Chassis, drawbar, front wall, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks and landing gear painted in a shade of black * Sideboard painting in RAL 9010 pure white * Painting of side walls in an individual RAL color available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 10.870 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2025, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2023, Oprema: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----General Attachments: * Jost mechanical landing gear at front * 2 mechanical folding supports at rear * Plastic toolbox, approx. 650 x 350 x 320 mm, mounted on the right side of the chassis at the front * Bolted underrun protection * Plastic quarter mudguards * Net hooks positioned at the central locking locations and 2 on the front wall ----Chassis: * High-tensile steel chassis ----Tipping Platform: Bodpfx Anol Th Hts Ijdc * Steel pallet-type three-way tipper body with continuous side walls, upper inside pipe reinforcement, no central stanchions; drop-down with drop side spring assistance * Bolt-on rear stanchions * Combination steel swing doors on the rear wall, 2-leaf, asymmetrically split, can swing and lock 270°, not drop-down, with additional pendulum frame for automatic rear wall opening during tipping; locking via galvanized rotary bolt at the rear and central locking; deactivation for auto rear wall function when tipping backwards with door open * 4 mm fine-grained steel floor plate * Rear mounting rails for loading ramps ----Load Securing: * 1 x 5 t lashing point in each corner, plus 4 x 3 t lashing rings on each side recessed into the external frame ----Ramps: * 1 pair of aluminium drive-on ramps, approx. 3,570 x 410 mm (load capacity: 10 t/pair), suitable for rubber-tired & tracked vehicles * Lockable storage compartment under the loading platform, integrated into the chassis for the ramps ----Tyres: * Tyres 285/70 R19.5 ----Painting: * Chassis, drawbar, underrun protection, rear stanchions and rear folding supports hot-dip galvanized * Axles, springs, air tanks and support winch painted black * Drop sides painted RAL 9010 pure white * Other RAL-coloured side wall painting available at extra cost ----Information: * Reinforced body with load securing certificate * Vehicle has a day registration (not previously in use) * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General Attachments: Bdjdpfx Asq Dyvven Isc * Jost landing gear at the front * External, hot-dip galvanized folding support legs at the rear * Plastic toolbox, front right exterior on the bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet steel bulkhead * Drop sides made of trapezoidal-profiled steel, foldable with drop-side lifting aid * Rear wall made of steel, can be inserted between ramps - storage bracket inside in front of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Optional installation of 3 t recessed lashing rings every 600 mm * Each front and rear corner equipped with 1 x 6.3 t lashing ring * Various holes in the front and rear cross members for 1.2 t lashing points * Profifix lashing rail along the center longitudinal axis for securing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, ramps, and rear wall * Drop side color in RAL 9010 pure white * Painting of the side walls in any RAL shade available at extra cost ----Information: * --Reinforced and certified body to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from week 29/2026

Stanje: novo, največja dovoljena obremenitev: 14.660 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, ETÜ-TA-R 19.0: ----Brakes: * Wabco EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: 2 x 10 t BPW Eco axles ----Suspension: * Parabolic springs – 110 mm wide – with tandem equalisation unit ----Drawbar / Drawbar Eye: Drawbar with 50 mm flange eye and height-adjustable drawbar ----Electrics / Lighting: * 15-pin electrical connector * LED tail lights Bsdpol Th Hljfx An Isdc * RDÜ tyre monitoring system ----General Attachments: * Jost landing leg at the front * External folding supports at the rear * Side underrun protection * Plastic quarter mudguards ----Low Loader Bed: * 50 mm softwood floor * Preparation in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of trapezoidal-profiled steel, foldable with drop side spring lifters * Steel rear wall can be slid in between the ramps – storage bracket inside in front of the front wall when not in use * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45 degrees bent, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In front and rear corners, each 1 x 10 t lashing ring; various holes in front wall and rear crossmember for 1.2 t lashing option * Profifix lashing rail centrally positioned along the longitudinal axis, with lashing capacity up to LC 3000 daN ----Ramps: * One-piece mech. grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be compacted to 20 mm) * Rear approach slope approx. 860 mm ----Painting: * Chassis, drawbar, front wall, rear wall, ramps, and folding supports hot-dip galvanised * Sideboard painted in RAL 9010 pure white * Painting of the side panels in any RAL colour available at extra cost * Axles, springs, air tank, flange eye and landing leg painted in black ----Info: * New vehicle with full manufacturer's warranty * Errors and prior sale subject to change ----Delivery Time: * Available immediately ex-works at Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 14.550 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2024, ETÜ-TA-R 19.0 ---- Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ---- Axles: * 2 x 11 t Gigant axles ---- Suspension: * Air suspension with manual lowering at the rear ---- Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye and height-adjustable drawbar ---- Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * 15-pin power connector * LED tail lights ---- General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Toolbox made of galvanized sheet steel approx. 650 x 350 x 320 mm, fitted on the right side (black powder-coated) * Side underride protection * Plastic quarter mudguards ---- Low Loader Platform: * Reinforcement package for drilling rig transport on the chassis – loading height +20 mm * 50 mm softwood floor in clamped design * Provision in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal-profiled steel sheet, foldable with board wall spring-assisted lifter * Steel rear wall, can be inserted between the ramps – storage bracket in front of the bulkhead when not in use * Rear stakes bolted ---- Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * Each front and rear corner with 1 x 10 t lashing ring; various holes in the headboard and end cross member for 1.2 t lashing options ---- Ramps: * One-piece mechanical steel grating ramps with spring assistance for one-man operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear access slope approx. 860 mm ---- Tyres: Bsdjpk D Ncspfx An Iedc * Wheelbase: 1,310 mm * Tyres: 235/75R17.5 ---- Painting: * Chassis, drawbar, headboard, tailgate, rear folding supports, and ramps hot-dip galvanized * Axles, springs, air reservoirs, and landing leg painted in black * Side boards painted in RAL 9010 pure white * Side walls can be painted in any RAL color for a surcharge ---- Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ---- Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: Bedpjrvvflofx An Iodc ----Brakes: * Drum brakes * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with compensating unit ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm up to 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * TPMS (tire pressure monitoring system) * LED lighting ----General attachments: * Jost landing leg at the front * Externally mounted, hot-dip galvanized drop-down support legs at the rear * Plastic toolbox, mounted front right on the bulkhead * Side impact protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Preparation in front of bulkhead for retrofitting container locks * Bolted bulkhead in smooth sheet metal * Trapezoidal profile steel side walls, foldable with side wall spring assist * Steel rear wall, slidable between the ramps – storage bracket inside the bulkhead when not in use * Screwed-in rear stanchions ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t recessed lashing rings possible every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in front and rear cross members for 1.2 t lashing options * Profifix lashing rail along the longitudinal axis (center), lashing option up to LC 3,000 daN ----Ramps: * Single-piece mechanical mesh approach ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (can be collapsed down to 20 mm) * Rear drive-up angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, ramps, and rear panel * Side wall color RAL 9010 pure white * Painting of the side walls in a different RAL color available at extra cost ----Information: * --Reinforced and certified construction according to EN 12642 XL, including load securing certificate-- * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. week 29/2026

Stanje: rabljeno, največja dovoljena obremenitev: 10.870 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2025, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2023, Oprema: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: Bdsdpfol Th Dusx An Iec * Parabolic springs with tandem equalizer set ----Drawbar / Flange eye: * Height-adjustable drawbar (300 mm adjustment range) with 40 mm flange eye ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----General attachments: * Jost mechanical landing gear in front * Two mechanical folding supports at the rear * Plastic toolbox approx. 650 x 350 x 320 mm mounted on the right side at the front of the chassis * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks located at the central locking mounting points as well as 2 hooks on the front wall ----Chassis: * Chassis fabricated from fine-grain steel ----Tipper body: * Steel pallet three-way tipper body with continuous side walls, upper sections internally reinforced with pipe, no central stanchions, drop-side design with tailgate spring lifters * Rear stanchions bolted * Combination steel wing doors at the rear, double-leaf, asymmetrically divided, can swing open and lock to 270°, not collapsible, fitted with additional pendulum frame for automatic tailgate opening during tipping operation; locking by galvanized rotary bar at the rear and central locking; deactivation for automatic tailgate function when tipping backward with open wing doors * 4 mm fine-grain steel floor plate * Rear mounting rails for loading ramps ----Load securing: * Each corner fitted with one 5 t lashing ring, each side fitted with four 3 t recessed lashing rings in the outer frame ----Ramps: * One pair of aluminum access ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tired & tracked vehicles * Rear lockable storage compartment for ramps integrated underneath the load area in the chassis ----Tyres: * Tyres 285/70 19.5 ----Paintwork: * Chassis, drawbar, underrun protection, rear stanchion, and rear support legs hot-dip galvanized * Axles, springs, air reservoirs, and landing gear painted in a shade of black * Side wall paintwork in RAL 9010 pure white * Other RAL color tones for side walls available at extra cost ----Additional Information: * Reinforced body with load securing certificate * Vehicle comes with one-day registration (never used) * Subject to errors and prior sale ----Delivery time: Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-ER 19.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering device Bdjdpfxomi Tmas An Isc ----Drawbar / Flange Towing Eye: * Drawbar with 50 mm flange towing eye, height-adjustable by 110 mm via offset plate ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * LED tail lights 12/24 Volt ----General Attachments: * Jost landing leg at the front * External folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right side * Side underrun protection * Plastic quarter mudguards ----Low-loader Platform: * Reinforcement package on chassis for drilling rig transport * 50 mm softwood floor, clamped type * Preparation in front of front wall for retrofitting container locks * Bolted smooth plate front wall * Split steel side walls – trapezoidal profile – foldable with central folding stanchion * Steel rear wall slide-in between ramps – bracket for storage in front wall when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45-degree angled, with 2 t lashing force every 480 mm * Option for installation of 3 t drop lashing rings every 600 mm * Lashing package: 1 x 10 t UVV lashing ring in each front and rear corner, 2 x 8 t UVV retractable lashing rings each side in the outer frame, various holes for 1.2 t lashing options in the front and rear crossmembers ----Ramps: * One-piece slide-in ramps 12 t/pair, ramps approx. 2,750 x 620 mm * Rear approach angle approx. 860 mm ----Loading Height: * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm ----Tyres / Wheelbase: * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 ----Paintwork: * Chassis, drawbar, front wall, rear flap, folding supports and access ramps hot-dip galvanized * ---Axles, air tanks, flange towing eye and landing leg painted in a shade of black--- * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.490 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, TRA-Kombi 18.0: * 3-in-1 solution: suitable for roll-off containers, skip containers, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 t axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrical / Lighting: * Tire pressure monitoring system (TPMS), display capability in truck via EBS signal (no truck-side installation required) * LED rear lights 12/24 V * 15-pin power connector Bodpel Tnwzsfx An Iodc ----General Attachments: * Tool box made of powder-coated sheet steel * Spare wheel carrier (basket type) on the right side * Closed side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * Foldable A-sign at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Steel deck with recessed rollers in the bogie area * Can transport roll-off containers with a container length of 5,500 – 7,000 mm * Pneumatic 4-point clamp locking and mechanical plug-in stop angles at the front of the guide track * Transport of up to 2 skip containers with a max. volume of 10 m³ possible * Includes 8 repositionable bin stops for lateral centering of the skips, front 4 stops plug-in with pivoting stop * Weld bead as anti-slip coating in the ramp area of the track * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for securing with tensioning elements, 4 cloverleaf-type lashing brackets per side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t recessed lashing eyes per side in the outer frame ----Ramps: * Aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles and drawbar painted black ----Additional Information: * Load securing certificate according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egstorf

Stanje: novo, največja dovoljena obremenitev: 14.400 kg, skupna masa: 19.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, ETÜ-TA-ER 19.0: ----Brake System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Flange Eye: * Drawbar with 50 mm flange eye and height adjustment of 110 mm by offset plate ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * LED tail lights 12 / 24 Volt Bdjdpfx Aemi Tcqon Iec ----General Attachments: * Jost landing gear, front * External folding supports, rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Reinforcement package for drilling rig transport on chassis * 50 mm softwood flooring, clamped * Preparation in front of front wall for subsequent installation of container locks * Bolted front wall, smooth sheet * Split side walls, steel sheet, trapezoidal profile—foldable with central folding stakes * Steel rear wall, sliding between ramps—holder inside front wall when not in use * Bolt-on rear stakes ----Load Securing: * Perforated outer frame, approx. 45 degrees bent, with 2 t lashing capacity every 480 mm * Option to install 3 t fall-arrest lashing rings every 600 mm * Load securing package: Each front and rear corner 1 x 10 t UVV lashing ring, each side 2 x 8 t UVV retractable lashing rings in outer frame; in front and end crossmember various bores for 1.2 t lashing options ----Ramps: * One-piece sliding ramps 12 t / pair, approx. 2,750 x 620 mm * Rear approach slope approx. 860 mm ----Loading Height: * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm ----Tires / Wheelbase: * Wheelbase: 1,810 mm * Tires: 235/75 R17.5 ----Paintwork: * Chassis, drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * ---Axles, air reservoirs, flange eye, and landing gear painted black--- * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: rabljeno, skupna masa: 13.500 kg, konfiguracija osi: 2 osi, prva registracija: 02/2018, dolžina tovornega prostora: 5.060 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2018, MUELLER MITTELTAL Priklopnik (KIPER) 5,06 m Uvožen / BREZ NESREČ V ZELO DOBREM STANJU! ? LETNIK IZDELAVE: 2018 ZRAČNO VZMETENJE VELIKOST PNEVMATIK: 385/55R19,5 MEDOSNA RAZDALJA: 115 PLATFORMA: 506 x 242 x 50 m SKUPNA MASA: 13.500 kg NOSILNOST: 6.350 kg TEL: KUBA – POLJSKO, ANGLEŠKO, NEMŠKO, ITALIJANSKO SEBASTIAN – POLJSKO, NEMŠKO, ITALIJANSKO, ????? LASZLO – MADŽARSKO Bedpfxjy E Ecno An Ijdc COSTEL – ROMUNSKO? (Pri nas uredimo vse izvozne formalnosti, vključno s številko) RADEK – ?????

Stanje: rabljeno, največja dovoljena obremenitev: 6.000 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, prva registracija: 05/2026, Oprema: ABS, * Müller Mitteltal KWH 8.8 ML Cable Transport Trailer * As-new condition and available immediately * Inquiry reference number: 11652 * TPMS Tire Pressure Monitoring System * EBS braking system, drum brakes, BPW axles, parabolic leaf springs * Front support winch, rear spring-assisted square tube supports with base plates, safety locking pins for variable support heights * Drawbar with 40 mm towing eye (height-adjustable) * 15-pin power connector * LED lighting * 315/80 R 22.5 tires, full steel mudguards * Swiveling cable drum mount * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of stepwise-offset polyamide centering cones * For drum diameters Ø 800–3,000 x (1,700 mm width between drum arms) * With locking clamp for securing the drum at the support arm ends, plus a center-mounted claw lock securing the cable drum assembly to the chassis * Motor-driven hydraulic push/pull cylinders with pipe rupture protection. Control valve with automatic neutral position, pressure relief valve, and lowering throttle. Hydraulic system connectors, hoses, and pipes in NW 13. * Drum drive: motor-driven hydraulic with oil motor, valves, and rubber-coated drive rollers (adjustable). Hydraulic speed control and brake for drum drive. * Separate hydraulic power pack with Hatz 1B30 silent diesel engine and hand start, 6.5 HP (150 bar), pressure supply by switching hydraulic lines—optionally via truck hydraulics or power pack * Toolbox approx. 500 x 350 x 400 mm * Chassis and drawbar hot-dip galvanized * Advertising panel integrated in the side protection, polyester-coated exterior in RAL white * ----as-new condition (used for only one project) * ---- * Financing available through our partner banks, with or without down payment or residual value, and various terms. Request a quote! * We are an authorized Müller Mitteltal dealer! * Example hire-purchase via our partner FM LeasingPartner from only €515 net/month over 72 months term (no down payment, zero residual value). * Request a quote from us! ---- * Our opening hours * Monday - Thursday: 08:00 - 17:00 Bedpfxoy Rb Tye An Iodc * Friday: 08:00 - 15:00 * Outside these hours, we are available by appointment * We speak German, English, Russian, Polish, and French ----

Stanje: rabljeno, konfiguracija osi: 2 osi, skupna širina: 25.000 mm, skupna višina: 40.000 mm, Leto izdelave: 2014, Oprema: ABS, Za vprašanja v zvezi z vozilom je vam na voljo gospod Seidel (po telefonu). MÜLLER MITTELTAL SF32BM/BT betonska polprikolica Nadgradnja: Liebherr HTM 1004 10m³, osi BPW, bobnaste zavore, vzmetni akumulator, Wabco ABS, 1. os dvižna, zračno vzmetenje, dovoljena skupna masa: 32.000 kg, lastna masa: 6.510 kg, nosilnost: 25.490 kg, profil pnevmatik: 1. os 14-15mm, 2. os 10mm Po želji vam pripravimo ponudbo za leasing ali financiranje. Gospod Seidel vas z veseljem vodi po telefonu. Več informacij najdete na naši spletni strani. ... Napake, spremembe in vmesna prodaja pridržane!!! Bdodpfsyfu Sdsx An Ijc = Dodatne informacije = Dovoljena skupna masa: 32.000 kg Za dodatne informacije se obrnite na gospoda Tobiasa Eberta.

Stanje: rabljeno, lastna masa: 4.500 kg, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 08/2015, naslednji pregled (TÜV): 07/2025, dolžina tovornega prostora: 4.800 mm, širina tovornega prostora: 2.400 mm, višina nakladalnega prostora: 1.000 mm, barva: modra, Leto izdelave: 2015, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, * German trailer * Condition as shown in photos * Müller-Mitteltal three-way tipper, model KA-TA-R 18.0 tandem * Tipper dimensions: 4,800 x 2,400 x 1,000 mm * Roll tarp * Air suspension * Disc brakes * Platform * Jost landing gear * Payload: 13,500 kg Bdjdjwz H Nbspfx An Isc If a new TÜV inspection is required, we are happy to offer this through our partner workshops. Our offer is generally WITHOUT new TÜV inspection, without new DGUV, without new SP, and without new UVV. You can find more trucks on our homepage at We speak the following languages: German, English, Polish, Turkish Note: We offer and strongly recommend viewing and inspecting the goods, to avoid any misunderstandings regarding their condition and suitability. Viewings and inspections are possible at any time by appointment and are expressly encouraged. All details are without guarantee. We do not assume liability for errors or incorrect information in the listing. The buyer is obliged to independently verify the condition and equipment of the goods/vehicles. Subject to changes, prior sale, and errors.

Stanje: rabljeno, največja dovoljena obremenitev: 4.960 kg, skupna masa: 10.500 kg, prva registracija: 04/1993, naslednji pregled (TÜV): 01/2026, dolžina tovornega prostora: 6.260 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 2.430 mm, prostornina tovornega prostora: 37 m³, Oprema: ABS, dvižna zadnja plošča, 2-axle tandem refrigerated trailer, 7 m, with 1 ton tail lift. * THERMOKING LND-II MAX (diesel engine) and stand-by cooling, 380 V ELECTRIC * Vehicle number for customer inquiries: 4593 * Tail lift * Air suspension * EBS (Electronic Braking System) * Anti-lock braking system (ABS) Bdedpfjykxflex An Ioc No liability for printing or typographical errors. Sale exclusively to commercial customers. Subject to prior sale and errors. Changes, prior sale, and errors are expressly reserved. The description serves solely for the identification of the vehicle and does not constitute a warranty in the legal sense of the purchase contract. The purchase contract description is binding. * TOP SERVICE & QUALITY * We are happy to provide you with a leasing, financing, or hire-purchase offer Guarantee insurance available upon request from the insurer * TÜV inspection / UVV LBW (tail lift safety test) / tachograph inspection and OBU (On-board Unit) installation can be arranged by our local partners * Export license plates for 30 days available All export documents can be provided, but must be requested individually * Toll collection for Toll Collect can be arranged in-house * Free transfer from Stuttgart airport or Metzingen (Württ) railway station * ARRIVAL TRAIN STATION: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP number * * ---- Visit us on our website at * Over 200 vehicles always in stock