Fliegl Nizki Nakladalnik nakup rabljenega (307)

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 11.800 kg, lastna masa: 3.000 kg, največja dovoljena obremenitev: 8.800 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: e77e603e96d0ea4194a7f7661, Further information Chassis central axle trailer Fine-grain steel welded construction 5 pairs of lashing eyes screwed to the floor/outer frame, each rated at 3 tonnes 2 additional pairs of lashing eyes screwed to the floor, each rated at 5 tonnes in the corners Support leg with gearbox at the front Folding rear support 2 wheel chocks with holder Galvanised steel underrun protection Rear spray flaps across full width Quarter shell mudguards Central axle trailer drawbar system Drawbar with certified 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles & suspension GFA or BPW drum brake axles Laser-measured axle/chassis alignment to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5 Manufacturer’s choice Factory silver steel rims Braking system 2-line compressed air braking system Hand spindle parking brake Crjdpfoi Riv Tex Ad Ush Integral air reservoir 2 fail-safe coupling heads at the front with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, including connection cable Attention: The trailer may only be towed by vehicles that ensure proper functioning of the ABS system! Electrics 24 volts, multi-chamber tail lights, side yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear Two 7-pin fail-safe plugs at the front, with connecting cable, Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness possible due to welding distortion! Platform length approx. 5,200 mm Front wall / corner stanchions 25 mm aluminium hollow profile, 320 mm high, front corner stanchions in steel volume design Side panels 25 mm aluminium hollow profile, 320 mm high, foldable and removable, subdivided by 1 pair of plug-in centre stanchions Rear wall / rear corner stanchions 1 pair of steel stanchions fixed to the frame with bracket for ramp locking, loading width approx. 2,430 mm Ramps 2 steel ramps, 3,100 mm long, 510 mm wide, split lengthwise, laterally adjustable, with handle on ramps wooden inlay with gas spring for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the gross weight may not be achievable due to permissible axle/support/kingpin loads. (Poor handling and trailing stability may result from improper load distribution) Country of registration/plates Country of registration: Germany with Dekra inspection and certificate (per §13 EC-FGV) 24/7 service hotline Prepared for single-line number plate holder Contour marking with reflective tape to ECE R 048, white on sides and red at rear Paintwork Frame DB 7350 Nova Grey, 10 years warranty against rust-through Front/rear panels aluminium anodised, centre stanchion DB 7350 Nova Grey Ramps hot-dip galvanised Note: Archive images!

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 09/2008, vzmetenje: zrak, Leto izdelave: 2008, Dodatne informacije: Znamka: FLIEGL Model: SVS580T Zgradba: platforma (platforma L=13.211 mm / Š=2.540 mm / V=930 mm) Leto izdelave: 09.2008 Vzmetenje: zračno Codpfxjwkdmvs Ad Uerh Zavore: bobnaste Dimenzije: D/Š: 17.700 mm / 2.550 mm Mase: dovoljena/masа praznega vozila: 58.000 kg / 14.310 kg Modelno leto: 2008 = Več informacij = Vzmetenje: zračno vzmetenje Prednja os: dvižna os Srednja os 1: krmiljena os Zadnja os: krmiljena os Lastna masa: 14.310 kg Nosilnost: 43.690 kg DGV: 58.000 kg Dimenzije (DxŠ): 1.770 x 260 cm Za dodatne informacije kontaktirajte Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche ali Deniss Urmaker.

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 18 kg, lastna masa: 6 kg, največja dovoljena obremenitev: 11 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 535119ca408d3bd5a8e74be51, Further information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring, storage box integrated into turntable front section Foldable rear support Wheel chocks with holders Aluminum side underrun protection Csdpfx Aei Ri N Hod Ujrh Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) Extendable widening to 3,000 mm (not in rear taper) (Track width of construction machines or vehicles to be transported must not exceed 2,550 mm external frame width), storage compartment for wood planks centered in the loading area, 70 mm planks for widening to 3,000 mm, Tie-down eyes low-bed 3 pairs of lashing points integrated in the floor at the front, each rated for 10 t 6 pairs of lashing mushrooms recessed in the top and sides of the external frame, each rated for 10 t 1x after neck area, rest distributed in between, spacing not greater than 1,200 mm 1x rear taper 5 pairs of ring lashing eyes recessed in external frame, each rated for 5 t (instead of stake pockets) Trailer turntable drawbar Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Twin steel rims, factory silver Braking System 2-line air brake system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, ABS and ALB, with ABS connector at the front, with connecting cable Attention: The trailer must only be towed by towing vehicles that ensure the effectiveness of ABS! Electric system 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white/red width marker lights at rear 2 white position lights at front 1 rotating beacon with bracket, switchable via parking lights (removable beacon) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm 2 x 7-pin fail-safe connectors at the front, with connecting cable Floor Front area steel floor, then 70 mm softwood floor, wheel arch area with steel/tread plate covering Rear taper with 70 mm softwood floor Low-bed area incl. rear taper 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety below, foldable (prevents lateral slipping, not in conjunction with hydraulic side shift) wooden planking with spring assist Operational Notes A special permit is required for an axle load of 10,000 kg. The permit must be applied for individually in each federal state, and the legislator is not obliged to grant approval for a 20 t gross vehicle weight. Customer's risk. The specified gross weight is technically possible, depending on the cargo the gross weight may not be achievable while observing the permitted axle, support, and kingpin loads. Registration / Plates Registration country: Germany EC type approval acc. to 2007/46 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paintwork Frame DB Nova grey Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, lastna masa: 7.300 kg, največja dovoljena obremenitev: 16.700 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 195f80ad09517628522e33a91, Further Information Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Rear mudflaps across the entire width Quarter shell fenders in front of 1st axle 1st pair of wheel recesses embedded after the kink in the loading bed area, ramped entry, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! The frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses embedded between the axles in the loading bed area, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The frame in the main beam area is 300 mm higher than the wheel recess. Sliding extensions for widening, extendable to 3,000 mm (not in tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Sliding extensions for widening, extendable to 3,000 mm, also at the bottom in the wheel recesses, foldable at the wheel recess extensions (extension not in the tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) 70 mm timber planks for extension to 3,000 mm Tie-down points on low loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front in the kink, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for attaching tie-down straps) 7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated at 10 t 1x at the front in the kink 6x in the loading bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points no greater than 1,100 mm Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Crsdpfxoi Ri Rve Ad Ueh Axles & suspension SAF drum brake axles Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-applied parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, LED side marker lights, 2 white position lights at the front 2 white/red lane guidance lights at the rear 2 x 7-pin fail-safe connectors at the front, with connection cable, 1 LED rotating beacon with holder, switched via side light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Front kink with steel/checkered plate covering Storage box embedded in the ramp to the kink, then with 70 mm softwood floor, in the wheel arch area with steel/checkered plate covering Tail ramp with 70 mm softwood floor Low loading area including tail ramp: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring assist Operating Instructions For 10,000 kg axle load an exemption is required, only indivisible loads allowed! The stated gross weight is technically possible, but depending on the type of load, the gross weight may not be achievable within the pe

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, lastna masa: 7.150 kg, največja dovoljena obremenitev: 16.850 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 2dff0c136c85096f36822a0bb, Further Information Chassis - Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring, storage box integrated into turntable front section Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflaps Extendable extensions to 3,000 mm (not at the rear bevel) (Note: The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Central storage compartment for timber boards on the loading platform 70 mm timber boards for extension to 3,000 mm Low-bed lashing rings 3 pairs of 10 t lashing points integrated into the front floor 6 pairs of 10 t lashing mushrooms recessed in the top and side of the outer frame 1 x by the neck area The remaining points are distributed at no more than 1200 mm intervals 1 x at the rear bevel 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (can be converted to 5 t ring lashing eyes, not included) Drawbar Turntable Trailer Coupling Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical Axle load equalisation (rocker balancing) Brake System 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake included 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles ensuring the proper function of ABS! Wheels and Tyres 235/75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver finish Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, followed by 70 mm softwood flooring; wheel arch covers in steel/chequer plate Rear bevel with 70 mm softwood flooring Low-bed area incl. rear bevel 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered, included With spring assist Operating Notes An exemption permit is required for 10,000 kg axle load—only indivisible loads allowed! The specified total weight is technically achievable, but depending on the load, the permissible total weight may not be reached due to axle/support/kingpin limits. (Poor driving and tracking may result from incorrect load distribution) Country of Registration/Plates Country of registration: Germany With Dekra inspection and appraisal (according to §13 EU-FGV) 24/7 service hotline Prepared for double-line license plate holder Contour marking with reflective stripes per ECE R 048, white to the side, red to the rear Paintwork Frame DB 7350 Novagrau 10-year guarantee against rust-through Codpfx Adji Riy Es Uerh Drawbar galvanized or black, manufacturer's choice Access ramps hot-dip galvanized Note: Archive images!

Stanje: novo, skupna masa: 41.000 kg, lastna masa: 9.800 kg, največja dovoljena obremenitev: 31.200 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: dc46d2e1cd272305b99fb3160, Further Information Vehicle consisting of: Chassis low-bed semi-trailer Steel welded construction, kingpin plate with replaceable double kingpin and two kingpin positions 24-ton, 2-speed landing gear, single-sided operation, straight lower section, without thrust compensation Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminum Quarter mudguards in front of and behind the axle assembly 1st pair of wheel recesses embedded in the low-bed drive lane area after the gooseneck, tapered for entry. Lower length approx. 1,600 mm, recess depth approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess. 2nd pair of wheel recesses between axles A and B. Lower length approx. 350 mm, depth approx. 260 mm. Note! Frame in the main beam area is 260 mm higher than the wheel recess. If wheel loaders are to be transported and the total height needs to be checked, please provide technical data sheets of the wheel loader types with exact information (if total height is exceeded -> customer responsibility, approval required), (depending on ground clearance under the machines, inserts in the wheel recesses may be required by the customer) Wheel recess covers extendable from the main frame, with wooden inserts. Extensions extendable to 3,000 mm (not in the rear bevel and not in the lower wheel recesses). (The track width of construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm.) Storage compartment for wooden planks on the gooseneck, crosswise at the front 70 mm planks for extension to 3,000 mm Lashing eyes low-bed trailer 2 pairs of ring lashing eyes, each 5t at the front on the gooseneck 11 pairs of lashing mushrooms recessed at the top and side in the external frame, each 10t 2x on gooseneck, 9x distributed on low-bed platform; first lashing point 250 mm from the front and last at max. 250 mm from the rear, distance between lashing points no greater than 1,100 mm 8 pairs of stake pockets recessed in the external frame, internal dimensions 70 x 40 mm, or instead of stake pockets, 5t ring lashing eyes recessed in the floor Axles & Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5 as per manufacturer's choice Steel rims in twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connection cable Attention: The trailer may only be towed by tractors that ensure the effectiveness of ABS! 2 non-interchangeable coupling heads at the front, without connecting line with lift & lower valve Axle load detection via EBS CAN bus signal, for display in the driver's cab (truck must be pre-equipped accordingly, not installed on truck; not a calibrated scale) Vehicle stability control system Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane mark lights at the rear Cjdpfx Aji Ri Hcjd Ujrh 2 x 7-pin, non-interchangeable sockets at the front, without connection cable 1 x LED beacon with holder, switched via parking light (lamp removable) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel/chequer plate covering Storage box embedded in the sloped transition to gooseneck Then with 70 mm softwood floor; in the lower wheel recesses and w

Stanje: novo, skupna masa: 50 kg, lastna masa: 14 kg, največja dovoljena obremenitev: 35 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 5c7120ea17bcf92d3b69899da, Further Information Chassis low-bed semi-trailer Steel welded construction, fifth wheel plate with replaceable 2-inch kingpin 24 t, 2-speed landing gear, single-side operation, with straight base, without compensating device Rear supports foldable 2x wheel chocks with holder Side underrun protection in aluminum Quarter mudguards in front of and behind the axle assembly with splash flaps behind each axle 1x storage box, W=2,350 mm x L=730 mm x H=640 mm, mounted transversely at the front on the floor of the gooseneck, with 2 storage trays Extensions extendable to 3,000 mm (not in the rear inclination) (the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber planks on the gooseneck, positioned crosswise at the front 70 mm timber planks for extension to 3,000 mm Excavator arm recess over the rear axles extending to the rear, approx. 500 mm wide and approx. 230 mm deep Lashing eyes for low loader 3 pairs of 10 t lashing eyes at the front of the gooseneck, 8 pairs of 10 t lashing eyes in the low-bed, 3 pairs of lashing strips in the driving lane area of the low-bed, 3 pairs of 10 t lashing eyes in the axle/rear area Axles & Suspension SAF drum brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Hydraulic forced steering acting on all 3 axles via fifth wheel wedge, Remote-controlled rear steering + auto-tracking (up to max. 20 km/h). Note: The truck must have a 2-pin NATO socket with at least 2 x 35 mm² for steering power supply. Power for the pump unit is supplied via NATO connection cable to the towing vehicle, no truck installation (rear steering must be used once per week). Air suspension Wheels and Tires 235 / 75 R 17.5 to manufacturer’s choice Steel twin wheels, factory silver Braking System 2-line compressed air brake system, color-coded lines for easy service. Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! 2 non-interchangeable coupling heads at front, no connecting hose with lift & lower valve, hold function in lowering position + auto-reset function Axle load detection via EBS CAN bus signal, for display in driver’s cab—truck must be pre-equipped, no installed weighing system (not calibrated) Codpfx Adji Ri Hge Ujrh Vehicle Stability System Trailer Info Center for display of vehicle data such as axle loads (not calibrated), mileage, and diagnostic/system messages. Electrics 24 volt, multi-chamber lights, yellow LED side marker lights 2 white LED position lights at the front 2 white/red lane monitoring lights at the rear 2 x 7-pin non-interchangeable sockets at the front, no connection cable 1x additional LED work light at rear, switched via reverse light 1x LED beacon with holder, switched by parking light (removable lamp) 2 pairs of double LED warning boards, extendable to 3,000 mm Flooring Gooseneck with steel/chequered plate covering 70 mm softwood flooring in the driving lane area, steel/chequered plate covering in the wheel arch area, low-bed left and right in driving lane area hydraulically raisable via truck PTO Rear inclination section with 70 mm softwood floor Low-bed length approx. 6,300 mm Drop Sides 25 mm aluminum hollow profile, 400 mm high, front and sides on gooseneck, plug-in type Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally mo...

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, lastna masa: 10.280 kg, največja dovoljena obremenitev: 13.720 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: ee3256d63dd23b3ad1bdf9ab0, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support legs 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Quarter shell fenders in front of the 1st axle Excavator arm trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated at 5 t each in the excavator arm trough, positioned laterally on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear taper 1 storage box recessed into the gooseneck on the floor with lid, W=720 mm/ L=520 mm / D=170 mm 1st pair of wheel recesses after the gooseneck, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 1600 mm, approx. 400 mm deep. Note! Main frame section 400 mm higher than wheel recess. 2nd pair of wheel recesses between the axles, recessed in the low-bed deck area, sloped for entry, length at bottom approx. 600 mm, approx. 300 mm deep. Note! Main frame section 300 mm higher than wheel recess. Removable wheel recess covers from the main frame, with wooden inserts. Distance from main frame longitudinal member to outside member approx. 1280 mm (wheel recess area) Extensions extendable to 3,000 mm, foldable at the wheel recess extensions (extensions not in the rear taper nor at the bottom of the wheel recesses) (The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber planks centrally on load area or underneath depending on technical feasibility 70 mm timber planks for extension to 3,000 mm Low-bed lashing points 1 pair of ring lashing points recessed in the gooseneck, each rated at 5 t 8 pairs of lashing mushrooms recessed in the top and side outer frame, each rated at 10 t 2 x at the front on the gooseneck 6 x in the low-bed – first lashing point 250 mm from the front, last maximum 250 mm from the rear, distance between lashing points not greater than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each rated at 5 t (can be converted to stake pockets) Drawbar Assembly for Turntable Trailer Cjdpfsi Ri I Nox Ad Uerh Drawbar with tested 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption Air suspension with lift & lower valve, separately operable at front and rear Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line pneumatic braking system Spring-loaded parking brake Trailer info center, displays vehicle data (e.g., axle load—not a calibrated scale) and odometer Axle load detection via EBS-Canbus signal, for display in the cab (truck must be pre-equipped, not installed in truck, not a calibrated scale) Vehicle Stability System Duomatic coupling at the front with connecting line to the truck tractor EBS, electronic braking system with EBS socket at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 volts, multi-chamber LED lights with resistor, side marker yellow LED lights, LED license plate lights (Note: Certain towing vehicles may show diagnostic errors despite systems working correctly) 2 white front position lights in LED 2 white/red lane marker lights at the rear in LED Additional LED w

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 18 kg, lastna masa: 5 kg, največja dovoljena obremenitev: 12 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 2b58968e34fac93b429a256e9, Further information Chassis Low-bed trailer Steel welded construction Turntable with robust ball-bearing slewing ring, storage box integrated into turntable front section Rear folding support Wheel chocks with holder Aluminum side underrun protection Full-width rear mud flaps Quarter-shell fenders in front of 1st axle Spare wheel holder for 1 spare wheel, including wheel mounting kit Spare wheel, same brand and specification as standard tires, steel rim Plastic tool box with shelf, w=620/h=360/d=440 mm, lockable with padlock (padlock not included) Lashing rings low-loader 3 pairs of lashing points (10 t each) integrated in front floor, 6 pairs of mushroom lashing points (10 t each) fitted on and into the outer frame at the top and sides: 1x at gooseneck, remaining distributed in between (distance max. 1200 mm), 1x on rear slope 5 pairs of recessed ring lashing points in the outer frame (5 t each, convertible to stake pockets) Drawbar equipment trailer turntable Drawbar with certified 40 mm towing eye Axles and suspension SAF drum brake axles Axle/chassis laser alignment for reduced tire wear and improved fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings Wheels and tires 235/75 R17.5 Manufacturer's choice Steel twin wheels, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, including connection cable, voltage converter for 12/24 Volt operation Note: Tractor/trailer requires a 7-pin 12 Volt socket! (Electric system with voltage converter required!) Attention: Trailer may only be towed by vehicles that ensure proper ABS functionality! Electrics 24 Volt, multi-chamber lights, yellow LED side lighting 2 white/red width marker lights at rear 2 white position lights at front Additional LED work light at rear, controlled via reversing light Crsdpei Ri Nxsfx Ad Ujh 2x 7-pin non-interchangeable plugs at front with connecting cable 1x 7-pin agricultural plug, voltage converter 12/24 Volt (for electrics only, not for ABS/EBS) Floor Steel floor in front section, followed by 70 mm softwood flooring, steel/chequered plate in wheel arch area Rear slope section with 70 mm softwood flooring Low-bed area including rear slope 8,200 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, timber-planked, with spring assist Operating notes Special permit required for 10,000 kg axle load; permit must be obtained separately in each federal state; no guarantee from authorities for 20 t GVW. Customer assumes risk. Country of registration / plates Country: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7-service hotline Prepared for double-line number plate holder Outline marking with reflective tape per ECE R 048, white side and red rear Paintwork Frame DB 7350 Nova grey 10-year corrosion warranty Drawbar galvanized or black, manufacturer's choice Ramps hot-dip galvanized Attention: Archive images!

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 11.800 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: ebf3f771e96394cd89e56bbb7, Further information Chassis Central-axle trailer Fine-grain steel welded construction 6 pairs of lashing eyes screwed into the floor/external frame, each rated at 5 tons 2 additional pairs of lashing eyes screwed into the floor, each rated at 5 tons, in the corners Gear support leg at the front Foldable rear support 2 wheel chocks with holder Steel underrun protection Full-width rear mud flaps Quarter-shell fenders 1 plastic toolbox with shelf, dimensions 620mm (w) / 360mm (h) / 440mm (d), lockable with a padlock (padlock not included) Central-axle trailer towing device Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles and suspension Drum brake axles, manufacturer’s choice Axle/chassis laser alignment to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel/rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and tires 235/75 R 17.5 Manufacturer’s choice Steel rims, factory silver Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Steel/Tread plate floor for high point load capacity Codpfxoi Rixro Ad Uorh Note: Minor floor waviness possible due to welding distortions! Platform length approx. 5,200 mm Rear slope approx. 900 mm Front wall / corner posts 25 mm aluminum hollow profile, height 400 mm Sideboards 25 mm aluminum hollow profile, height 400 mm, foldable and removable Rear wall / rear corner posts 1 pair of steel posts attached to the frame with bracket for ramp locking, entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handle on the ramps Covered with 3 toothed steel rails With gas pressure springs for single-person operation Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame hot-dip galvanized incl. passivation 15-year warranty against rust-through Front wall: aluminum Sideboards: anodized aluminum Loading ramps: hot-dip galvanized Attention! These are archive images.

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 408ba9a39bbb8087056d6e563, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Crodpfx Aji Ri Dajd Ush Flooring Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: novo, konfiguracija osi: 3 osi, lastna masa: 24.000 kg, največja dovoljena obremenitev: 7.550 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: ede0610378cbe39cc4883251d, Further information Chassis Low-loader Trailer Steel welded construction 1st pair of wheel recesses embedded in the driving lane area after the steel platform, bevelled for entry, approx. 1,400 mm long at the bottom, approx. 400 mm deep. Note! Frame is 400 mm higher in the main beam area than at the wheel recess. If machines are to be transported where overall height must be verified, we request a technical data sheet for the machine types with precise specifications (if overall height is exceeded -> customer is responsible, approval required). Depending on ground clearance under the machines, inserts for the wheel recesses may be required on the customer side. Turntable with robust ball race ring, storage box integrated in the turntable front section Rear supports foldable 2 wheel chocks with holder Aluminium side underrun protection Full-width rear mudflap Extending wideners to 3,000 mm (not in rear bevel area) (The track width of the construction machines or vehicles to be transported must not exceed the outside frame width of 2,550 mm) Central storage compartment for wooden planks on loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes low-loader 3 pairs of 10 t lashing points integrated in the floor at the front incl. 6 pairs of lashing mushrooms recessed on top and at the side in the outer frame, each 10 t 1 x at the gooseneck The remaining distributed between, spacing not greater than 1,200 mm 1 x rear bevel 5 pairs of stake pockets integrated into the outer frame, internal 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly trailer turntable Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser aligned to reduce tyre and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colour-coded piping for easy service Spring loaded parking brake 2 interchange-proof coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by tractor units which ensure the functionality of ABS! Wheels and tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED illumination 2 white position lights at front 2 white/red track marker lights at rear 2 x 7-pin interchange-proof plugs at front with connecting cable 1 LED beacon with bracket, switched via parking light (removable lamp) 2 pairs of double warning boards, LED-lit and extendable up to 3,000 mm Floor Codpfsi Ri Ryex Ad Usrh Front area steel floor, incl. Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-loader deck incl. rear bevel 8,200 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring lifting aid Operating instructions For 10,000 kg axle load, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achievable while complying with permissible axle/kingpin/saddle loads. (Poor driving and tracking behaviour possible due to incorrect load distribution) Country of registration / Plates Country of registration: Germany incl. With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for two-line number pla

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 24.000 kg, lastna masa: 5.700 kg, največja dovoljena obremenitev: 18.300 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: b50cac2c60a813b0968994fa0, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Full-width rear mudflap Preparation for widening to 3,000 mm (holes in outer frame, not in rear bevel) Low-loader lashing rings 1 pair of lashing cutouts embedded in the front longitudinal beam at the gooseneck, each rated for 10 t 7 pairs of lashing mushroom pins embedded on top and side of the outer frame, each rated for 10 t 1 x on the front gooseneck 5 x in the low-bed area 1 x in the rear bevel Crjdpfei Ri Agex Ad Ueh 12 pairs of lashing holes in the outer frame, each rated for 5 t (for lashing strap hooks) 5 x at the gooseneck, 6 x in the low-bed area, and 1 x in the rear bevel Drawbar system for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles, brand as per manufacturer’s choice Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 unmistakable coupling heads at the front, with connecting lines to the truck, Connecting lines extended by approx. 60 cm No ABS, but with mechanical ALB (automatic load-dependent brake valve), thus maximum 60 km/h permit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 7-pin 12 Volt plug at the front with connecting cable, extended by approx. 60 cm 1 LED beacon with holder, operated via parking light (lamp removable) 2 pairs of illuminated and extendable warning plates up to 3,000 mm Floor Front gooseneck with steel/chequer plate covering Toolbox recessed in the drive-over slant to gooseneck Following area with 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-bed loading area including rear bevel: 5,900 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wooden covering Spring-assisted lifting Operating Instructions For axle loads of 10,000 kg, an exemption permit is required; only indivisible loads permitted!!! The stated total weight is technically possible; depending on the load, the total weight may not be achievable within the allowable axle/support and fifth wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate for max. 60 km/h approval, towing vehicle as agricultural/forestry vehicle (LoF), (for Switzerland, max. 40 km/h possible) Prepared for double-line license plate holder No contour markings / reflective tape according to ECE R 048 Painting Frame: DB 7350 Novagrau 10-year corrosion protection warranty Drawbar galvanized or black, according to manufacturer’s choice Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 15431365fe5515297a6a9fb05, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball-bearing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mud flaps Half-shell mudguards on 1st and 2nd axles with antispray mud flaps behind each axle, antispray mud flaps before and after 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points each 5 t located in the excavator arm recess on the side at the main frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf insert, W=620/H=360/D=440 mm, can be locked with a padlock (lock not included) 1 storage box recessed into the floor at the gooseneck, with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm 70 mm timber planks for extension to 3,000 mm Storage compartment for timber planks under the loading platform Lashing eyes (40 securing options) Cedpfxei Ri A Ss Ad Ujrh 1 pair lashing eyes on gooseneck, each 5 t 9 pairs lashing mushrooms integrated on top and side of outer frame, each 10 t 2 x on gooseneck to the front 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each 5 t (for tension belt attachment) 3 pairs of additional folding lashing eyes, each 10 t 1 x inside next to the main frame at the beginning of the low-bed 1 x on gooseneck (protruding) 1 x recessed behind the last axle Trailer towing device turntable Drawbar with tested 50 mm towing eye, towing eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum braked axles Parabolic spring suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) front and rear Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 Volt, multi-chamber lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable 1 LED beacon with holder, operated via sidelights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel chequer plate covering Followed by 70 mm softwood floor, wheel arch area with steel chequer plate Rear bevel with 70 mm softwood floor Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber overlay Spring-assisted lifting Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for double-line licence plate holder Conspicuity marking with reflective strips according to ECE R 048, white at the side and red at the rear Warning panel according to ECE - 70 Coating Frame hot-dip galvanized incl. passivation, 15-year corrosion guarantee Drawbar galvanized or black, as per the manufacturer's choice Loading ramps hot-dip galvanized Attention! Archive pictures shown!

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: d461243f559015adca5bb372c, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Credpfji Ri Dlox Ad Ujh Full-width rear mudflap Half-shell mudguards on 1st axle with anti-spray mudflaps Anti-spray mudflaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: W=620/H=360/D=440 mm, lockable with a padlock Extendable width up to 3,000 mm Central storage compartment for timber planks on loading area 70 mm timber planks for widening to 3,000 mm Lashing rings for low-bed (40 lashing points) 1 pair of lashing apertures recessed in the front longitudinal beam at the gooseneck, each rated for 10 t 4 pairs of lashing holes in the external frame, each rated for 5 t (for lashing strap hooks) 7 pairs of lashing mushrooms embedded on top and side of the outer frame, each rated for 10 t 1 at the front on the gooseneck 6 in the low-bed section First lashing ring 250 mm from the front, last max. 250 mm from the rear, spacing between lashing rings not greater than 1,100 mm 5 pairs of stake pockets embedded in the external frame, internal dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes) 2 pairs of additional folding lashing eyes, each rated for 10 t 1 on the gooseneck (protruding) 1 recessed behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 40 mm towing eye Axles + Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and tyres 235/75 R 17.5 Manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line pneumatic braking system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connecting lines to towing vehicle ABS and ALB, ABS connector at the front with connecting cable Brand: Wabco, Knorr or Haldex Electrics 24 Volt, multi-chamber rear lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with bracket, controlled via parking lights (removable beacon) 2 pairs of warning boards, double, LED illuminated, extendable to 3,000 mm Floor Gooseneck front with steel tread plate covering Storage box recessed in the transition to the gooseneck Followed by 70 mm softwood flooring, wheel arch areas with steel tread plate covering Rear chamfer with 70 mm softwood flooring Low-bed area incl. rear chamfer: 6,500 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber-layered Hydraulically operated via tractor PTO with throttle, operated from left-hand side, front Hydraulic connection with SVK coupling NW 10/3, including connecting hose Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Warning board according to ECE - 70 Paintwork Frame hot-dip galvanized incl. passivation 15-year warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Note: These are archive images!

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 10 kg, lastna masa: 2 kg, največja dovoljena obremenitev: 8 kg, velikost pnevmatike: 235/75 r 17,5, številka stroja/vozila: dd98a7658922be8f2e25bcadb, Further information Chassis Central Axle Trailer Low-bed Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support 2 wheel chocks with holders Steel mudguards over both wheels Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 250 mm Axles & Suspension Euro-axles (manufacturer’s choice), with tapered roller bearings and S-cam brakes Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 (manufacturer’s choice) Factory silver steel rims Braking System 2-line compressed air braking system Spring-loaded parking brake 2 mistake-proof coupling heads at the front, with connection lines to the towing vehicle, ABS and ALB, with ABS plug at the front, including connection cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white marker lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin mistake-proof plugs at the front, including connection cable Body TTS Low-mounted steel trough, bridge floor made of steel/chequer plate covering, steel sidewalls solidly welded to the floor Bridge length 4500 mm; trough at the front and sides with load-lock profile for attaching lashing straps (8 points in front, 12 per side) Note: Slight floor waviness possible due to welding distortion! 2 pairs of lashing rings, one at the corners of the steel trough front and one at the rear floor, each rated 5t 2 additional pairs of lashing rings in the floor, each rated 5t Ramps Steel ramps, 2300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps Wooden covering Gas spring assist for one-man operation Operating instructions The stated gross weight is technically possible; depending on the load, the gross weight may not be achievable while observing the permissible axle/load and saddle loads. (Poor driving and tracking performance possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Outline markings with reflective tape according to ECE R 048, white on the sides and red at the rear Codpfei Ri Ebsx Ad Usrh Paintwork Frame RAL 3002 Carmine red Ramps hot-dip galvanized Note: Archive images!

Stanje: novo, skupna masa: 41.000 kg, lastna masa: 8.900 kg, največja dovoljena obremenitev: 32.100 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 2428b2018baf171e60fef6740, Further information Chassis for Low-bed Semi-Trailer Steel welded construction, king pin mounting plate with interchangeable 2 kingpins and 2 kingpin positions, 24 t, 2-speed landing gear, single-sided operation, with straight lower frame, without compensation for extension Rear folding support 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear spray flap Fenders in front of the 1st axle and behind each axle, with anti-spray as per EU regulations Extendable outriggers to 3,000 mm (not at the rear incline) (track width of construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central storage compartment for timber planks on the loading area 70 mm timber planks for extension to 3,000 mm Tie-down points, low-loader 2 pairs of ring lashing eyes, each 5 t, at the front on the gooseneck 11 pairs of lashing mushrooms, recessed into the upper and side outer frame, each 10 t 2 x on the gooseneck 9 x distributed in the low-bed area Crjdpfoi Ri E Rjx Ad Ueh First lashing eye 250 mm from front, and last max. 250 mm from rear; spacing between lashing eyes no greater than 1,100 mm 8 pairs of stake pockets embedded in the outer frame, inner dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Axles & Suspension SAF drum brake axles Axle/chassis laser-aligned to reduce tyre wear and fuel consumption Air suspension Wheels and Tyres 235 / 75 R 17.5, make per manufacturer's choice Steel twin wheels in factory silver Braking system 2-line compressed air brake system Colour-coded piping layout for easy maintenance Spring-loaded parking brake EBS (Electronic Braking System) with EBS socket at the front, no connection cable Note: This trailer may only be towed by vehicles capable of ensuring the ABS function! 2 mistake-proof coupling heads at the front, no connection line With lift & lower valve Axle load detection via EBS CAN bus for display in cab, compatible truck required, no truck installation (not a certified weighing system) Vehicle stability control system Electrics 24 volts, multi-chamber lights, side LED marker lights (yellow) 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin mistake-proof sockets at the front, no connection cables 1 LED beacon with holder, switched via sidelights (removable beacon) 2 pairs of double LED illuminated warning boards, extendable to 3,000 mm Flooring Gooseneck with steel plate covering Storage box built into the slope to the gooseneck then with 70 mm softwood flooring, in wheel arch area with steel/tread plate covering Rear incline with 70 mm softwood flooring Low-bed area including rear incline: 9,200 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber-covered Hydraulically operated via tractor PTO with restrictor, controls on left side (driver’s side) in front Hydraulic connection with SVK coupling NW 10/3, without hose Operating instructions For axle loads of 10,000 kg, an exceptional permit is required, only indivisible loads permitted!!! Special permit required if 40 t gross combined weight is exceeded! The total weight specified is technically feasible; depending on the load, the total weight may not be achievable while adhering to permissible axle, support, and fifth wheel loads. (Poor handling and tracking possible due to incorrect load distribution) If applying for an exceptional permit for heavy haulage vehicles subject to authorization, an axle load indicator i

Stanje: novo, skupna masa: 41.000 kg, lastna masa: 11.800 kg, največja dovoljena obremenitev: 29.200 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 364a8214fd0c4afa2b936c7db, Further information Chassis Low-loader Semi-Trailer Steel welded construction, fifth wheel plate with interchangeable 2" kingpin and 2 kingpin positions (not in combination with forced steering) 24 t, 2-speed landing gear, single-side operation, with semi-circular lower part and straight connector plate, with load compensation Foldable rear support Wheel chocks with holders Aluminum side underrun protection Splash guards in front of the first axle and behind each axle, with anti-spray, according to EU standards Stainless steel toolbox, width=600 / height=400 / depth=500 mm, with polished lockable door Lifting table behind gooseneck, approx. 3000 mm long, hydraulically liftable for transition over gooseneck, with mechanical locking in raised position. Operated by remote control Electric winch, 24 volt, 8165 kg pulling force, mounted centrally at the very front of the load area on the gooseneck, installed in stainless steel box with door (subject to technical feasibility, to be checked in detail), operated by remote control, cable length 35 m x approx. 10 mm, with roller rope window and removable guide rollers on the gooseneck and rear incline Lashing eyes low-loader: Gooseneck: 5 pairs of lashing eyes integrated into the outer frame, each 5 t. 2 pairs of lashing eyes in the center, each 5 t. 1 pair of lashing points at the top and outside in the outer frame in the neck incline, each 10 t Deck: 4 pairs of lashing eyes integrated into the outer frame, each 5 t. 4 pairs of lashing eyes in the center, each 5 t. 1 pair of lashing points at the top and outside in the outer frame, each 10 t Cedpfei Ri E Usx Ad Uorh Lowered bed: 4 pairs of lashing eyes integrated into the outer frame, each 5 t. 5 pairs of lashing eyes in the center, each 5 t. 4 pairs of lashing points at the top and outside in the outer frame, each 10 t Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tire wear and fuel consumption Last axle self-steering, with automatic reverse lock via reverse light and additional locking function on the vehicle via hand knob Air suspension with raise & lower valve, hold function for lowering & auto reset function Wheels and Tires 235 / 75 R 17.5 by manufacturer’s choice Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle driving stability system Axle load detection via EBS CAN bus signal for display in the driver’s cab (truck must be suitably equipped; not for trucks—no calibrated scale) 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! Electrics 24 Volt, multifunction lights, yellow LED side lighting 2 white position lights at the front 2 white/red track marker lights at the rear All lights in full LED version (note: Some tractors may show diagnostic errors despite full function) 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, without connecting cables Additional LED work light at the rear, switched via reverse light LED beacon with bracket, switched via parking light (removable beacon) Pair of warning boards, double LED illuminated and expandable to 3,000 mm, removable with plug Floor Gooseneck covered with Mega Grip serrated grating Low-bed area covered with Mega Grip serrated grating Rear incline covered with Mega Grip serrated grating

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 11 kg, lastna masa: 2 kg, največja dovoljena obremenitev: 9 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: a3b1347da4aa7f31dceb875db, Further Information Chassis Central Axle Trailer Fine-grained steel welded construction Crodsi Ri Ilspfx Ad Ush 6 pairs of lashing eyes bolted to the outer floor/frame, each rated at 5 tons Gear support leg at the front Foldable rear support 2 wheel chocks with holder Steel underrun protection Full-width rear mudflap Quarter-shell fenders Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & Suspension BPW drum brake axles Axles/chassis laser-measured for reduced tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Factory silver steel rims Braking System Dual-line air brake system Hand spindle parking brake Integral air reservoir 2 interchange-proof coupling heads at the front with connecting pipes to the towing vehicle ABS and ALB, ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side markers 2 white front position lights 2 white/red rear marker lights 2 x 7-pin interchange-proof plugs at the front, with connecting cable Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness possible due to welding distortion! Platform length approx. 5,200 mm Rear tapering approx. 900 mm Front wall / corner posts 25 mm aluminum hollow profile, 320 mm high Side walls 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / corner posts 1 pair of steel stanchions fixed to the frame and with holders for securing the loading ramps, entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps wooden inlay with gas strut for one-person operation Operating Instructions The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable within the permitted axle/support/coupling loads. (Poor driving and tracking may result from incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau, 10-year warranty against rust-through Front wall aluminum Side wall anodized aluminum Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 628cde0fe99cc2d3c8eaa8dd8, Further Information Chassis Low-Loader Trailer Steel welded construction Turntable with robust ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Crodpfx Adei Ri Ddj Uoh Side underrun protection made of aluminium Full-width rear spray flap Half-shell mudguards on 1st axle with anti-spray flaps, anti-spray flaps behind 2nd and 3rd axle 1 plastic toolbox with shelf, dimensions: width=620 mm / height=360 mm / depth=440 mm, lockable with padlock (padlock not included) Extendable width up to 3,000 mm Storage compartment for wooden planks in the centre of the loading area 70 mm wooden planks for extension to 3,000 mm Tie-down lugs for low loader (40 lashing points) 1 pair of lashing cut-outs in the longitudinal beam at the front, recessed into the gooseneck, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for securing with lashing straps) 7 pairs of lashing mushrooms, recessed at the top and side of the outer frame, each rated at 10 t 1 at the front on the gooseneck 6 in the low bed First lashing point 250 mm from the front, last max. 250 mm from the rear, spacing between lashing points not greater than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, interior dimensions 70 x 40 mm (convertible to 5 t ring lashing points, not included) 2 additional pairs of folding lashing rings, each rated at 10 t 1 on the gooseneck (protruding) 1 behind the last axle, recessed in the floor Towing Device Turntable Trailer Drawbar with certified 40 mm towing eye Axles and Suspension Drum brake axles, manufacturer’s choice Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalisation (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims, twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front with connecting lines to the tractor unit ABS and ALB, with ABS socket at the front and connecting cable Manufacturer: Wabco or Knorr Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with bracket, switched with parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/chequer plate covering Toolbox recessed into transition slope to gooseneck Following area with 70 mm softwood floor, steel/chequer plate in wheel arch area Rear taper with 70 mm softwood floor Low-loader deck including rear taper: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber surfaced With spring lift assistance Country of Registration / License Plates Country of registration: Germany 24/7-Service Hotline Prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on sides, red at rear Warning sign according to ECE-70 Painting Frame hot-dip galvanized including passivation 15 years’ warranty against corrosion perforation Drawbar galvanized or black, manufacturer’s choice Loading ramps hot-dip galvanized Attention! Archive images shown!

Stanje: novo, skupna masa: 57.000 kg, lastna masa: 12.800 kg, največja dovoljena obremenitev: 44.200 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: df15479123e15bcf265d560e1, Further Information Chassis low-bed semi-trailer Steel welded construction, fifth wheel plate with replaceable 2 king pins and 2 king pin positions 24 t, 2-speed landing gear, operated from one side, with straight base, without load equalizer Rear support retractable 2 wheel chocks with holders Aluminum side underrun protection 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with padlock (lock not included) Extendable widenings to 3,000 mm (not at rear taper) (the track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Compartment for wooden planks on neck, transverse at front Wooden planks 70 mm for widening to 3,000 mm Telescoping Crjdpfx Asi Ri Hned Ujh Central tube frame made of precisely welded, interlocking telescopic frame sections. Extendable by max. 6,000 mm and lockable every approx. 1,000 mm. Payload/point load is reduced when extended! Locking by mechanical bolt lock with sliding table Tie-down eyes low-bed 2 pairs of ring tie-down eyes (each 5 t) at the front on gooseneck 11 pairs of lashing points recessed at the top and sides in the outer frame (each 10 t) 2x on gooseneck 9x in low-bed area distributed; first tie-down eye 250 mm from front and last max. 250 mm from rear, distance between tie-down eyes not greater than 1,100 mm 8 pairs of stake pockets recessed in outer frame, internal 70 x 40 mm (convertible to 5 t ring tie-down eyes, not included) 3 pairs of folding tie-down eyes additionally recessed in low-bed area, each 10 t, 1 at start of low-bed, 1 in front of 1st axle, and 1 behind 3rd axle Axles & Suspension SAF drum brake axles Axles/chassis laser alignment: reduces tire wear and fuel consumption Last 2 axles hydraulically steered, with automatic reverse lock via reversing light and manual lock via hand button on vehicle Air suspension with raise & lower valve Wheels & Tires 235/75 R 17.5 brand Fulda Steel twin wheels, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the driver’s cab (truck must be prepared accordingly, not installed in vehicle, not certified scale) 2 fail-safe coupling heads at front, without connecting line EBS electronic brake system with EBS socket at front, without connecting cable Note: The trailer may only be towed by tractor vehicles that guarantee the effectiveness of ABS! Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at front 2 white/red lane marker lights at rear 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning panels, double LED-illuminated and extendable to 3,000 mm 2 x 7-pin, fail-safe sockets at front, no connecting cable Floor Gooseneck with steel / chequer plate covering Storage box recessed in approach ramp to gooseneck then with 70 mm softwood flooring, in wheel arch area steel / chequer plate covering Rear taper with 70 mm softwood flooring Side walls 25 mm aluminum hollow profile, 400 mm high, plug-in, at front and sides on gooseneck Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally shiftable wood-covered Hydraulic via tractor auxiliary drive with throttle Hydraulic connection with SVK coupling NW 10/3, without connecting hoses Operating Instructions An exemption permit is required for 10,000 kg axle load

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24.000 kg, lastna masa: 9.900 kg, največja dovoljena obremenitev: 14.100 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 55d3c5c03e032385649769b1b, Further Information Chassis Low-Loader Trailer Codpfxei Ri I Ej Ad Uorh Steel welded construction Turntable with heavy-duty slewing ring, integrated storage box incl. Turntable front structure Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mud flaps Extendable widenings to 3,000 mm (not at rear taper) (track width of the machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central compartment on loading area for timber planks 70 mm timber planks for widening to 3,000 mm Lashing points Low-loader 3 pairs of integrated lashing points, each rated to 10 t, at the front floor 6 pairs of mushroom lashing points, top and side integrated in outer frame, each 10 t 1 x at neck area remaining points distributed, distance no greater than 1,200 mm 1 x at rear taper 5 pairs of stake pockets integrated in the outer frame, internal size 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly for trailer turntable Drawbar with certified 40 mm towing eye Note: For 40 mm towing eye, the maximum permissible gross weight of the towing vehicle is 18,000 kg. Otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Laser-aligned axles/chassis to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Steel twin wheels, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the truck ABS and ALB, with ABS connector at front, connection cable included Attention: The trailer may only be towed by vehicles that ensure ABS functionality! Electrics 24-volt multi-chamber lights, side yellow LED lighting 2 white front position lights 2 white/red rear lane marker lights 2 x 7-pin non-interchangeable connectors at the front, with connection cable 1 LED beacon with bracket, operated via parking lights (removable beacon) 2 pairs of warning boards, double LED-lit and extendable to 3,000 mm Floor Steel floor at front section thereafter 70 mm softwood floor, in wheel arch area with steel/chequer plate covering Rear taper with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable wooden inlays spring-assisted lifting Operating instructions Exception permit required for 10,000 kg axle load, only indivisible loads allowed!!! The specified total weight is technically possible. Depending on the cargo, the full gross weight may not be achieved while observing permissible axle/pin/support loads (poor tracking and handling may result from incorrect load distribution) Country of Registration / Plates Registration country: Germany 1 with Dekra inspection and report (according to §13 EC-FGV) 24/7 service hotline prepared for 2-line license plate holder Conspicuity markings with reflective strips acc. ECE R 048, white on the sides, red at the rear Paint Frame RAL 3002 Carmine Red 10 years warranty against rust-through Drawbar galvanized or black, at manufacturer's discretion Loading ramps hot-dip galvanized Attention: Archive photos!

Stanje: novo, konfiguracija osi: 2 osi, skupna masa: 18 kg, lastna masa: 4 kg, največja dovoljena obremenitev: 13 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: 6d88bda3a1ee2464a81b34f36, Further Information Chassis Low Loader Trailer Steel welded construction with a slight central camber, turntable with heavy-duty ball bearing slewing ring, chocks with holders, quarter shell mudguards in front of and behind each axle. Lashing Points Low Loader Over front axle: 2 pairs of ring lashing eyes (each 5 t) at the front on the cranked section Low-bed: 4 pairs of lashing eyes (each 6 t) at the sides of the lowbed 5 pairs of lashing eyes (each 5 t) between the longitudinal beams Drawbar Assembly Turntable Trailer Drawbar with certified 40 mm towing eye, mechanically adjustable in length by 6 x 100 mm increments and lockable (Drawbar length 1,700 – 2,300 mm) Axles + Suspension BPW drum brake axles with 10 t axle load each, slack adjusters. Continuous axle brake test up to 105 km/h. Rear axle can be removed manually. To do so, release air locking mechanism, lower the rear section to the ground, disconnect hydraulic hoses from rear section, insert the transport bar into a rear socket, and by gently pushing down and simultaneously pulling backwards, release rear section (parking brake released). After loading/unloading, move rear section into position and hook up to mark. Then raise rear section to driving height and connect hydraulic hoses. Confirm bolt locking (visual inspection if bolt snaps in) and check rear function. Air suspension with lift & lower valve. Cedpei Ri N Asfx Ad Uerh Wheels and Tires 235/75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver. Braking System 2-line compressed air brake system, spring-loaded parking brake, 2 fool-proof coupling heads at front with connection lines to tractor, EBS, electronic brake system with EBS plug at front with connection cable. Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 volt, multi-chamber lights, yellow LED side marker lights, 2 white position lights front, 2 white/red lane control lights rear, revolving beacon with bracket, powered via parking light (removable), 2 pairs of warning boards double LED illuminated and extendable up to 3,300 mm, removable with plug, 2 x 7-pin fool-proof plugs at front with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (for electrics only, not for ABS/EBS) Floor Steel/aluminum checker plate floor on cranked section, between longitudinal and cross beams with perforated cover plates. Axle cover not drive-over, widening to 3,000 or 3,300 mm possible. Operating Instructions Note! For 10,000 kg axle load, a special permit is required. Permit must be applied for separately in each federal state; the legislator is not obliged to grant approval for 20 t GVW. Customer’s risk. Special permit required if total train length exceeds 18,750 mm. Observe country-specific registration regulations. The stated gross weight is technically possible; depending on the cargo, the gross weight may not be achievable in compliance with permissible axle, support, and fifth wheel loads. Observe BO-circle!!! Registration / License Plates Registration country: Germany, with Dekra inspection and report (per §13 EC-FGV), prepared for single-line license plate holder, ECE-70-compliant warning board, contour marking with reflective strips per ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL black Attention: Archive images!

Stanje: rabljeno, konfiguracija osi: 2 osi, skupna masa: 10.500 kg, lastna masa: 2.500 kg, največja dovoljena obremenitev: 8.000 kg, prva registracija: 07/2022, velikost pnevmatike: 235/75 r17,5, Leto izdelave: 2022, številka stroja/vozila: 816b3dfbfa1c7d49b7d052bd6, Further information Chassis: Central axle trailer, low-bed Fine-grained steel welded construction, gearbox support foot at the front, telescopic rear support, wheel chocks with holder, steel fenders over both wheels Coupling system: Central axle trailer Drawbar with certified 40 mm towing eye, height-adjustable by spindle, max. adjustment range 250 mm Axles & Suspension Euro axles of our choice, with tapered roller bearings and S-cam brake, axles/chassis laser-aligned to reduce tire wear and fuel consumption, parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker balance) Brake system 2-line compressed air brake system, spring-actuated parking brake, 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Note: The trailer may only be towed by vehicles which ensure the effectiveness of the ABS! Electrics 24 volt, multi-chamber tail lights, yellow LED side marker lights, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 1 x 15-pin plug at the front, with connection cable. Deck TTS Low-mounted steel trough, deck floor made from steel/chequer plate, steel sidewalls solidly welded to the floor, deck length 5,500 mm, trough with Load-Lock profile at the front and sides for lashing strap attachment (8 pieces at the front, 16 pieces on each side) Note: Slight floor warping may occur due to welding distortion! Crjdpfx Adoqmc Rao Ueh Pair of lashing rings: 1 x at each front corner of the steel trough and 1 x at the rear in the floor, each rated at 5 tons. Additional pair of lashing rings in the floor, each rated at 5 tons. Drive-on ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable, with grip handles on the ramps, wood-clad, with gas struts for single-operator handling Operating notes The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while adhering to the permissible axle, support and saddle loads. (Poor driving and tracking behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany, with Dekra inspection and certificate (according to §13 EG - FGV), prepared for single-line licence plate holder, contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear.

Stanje: novo, konfiguracija osi: 3 osi, skupna masa: 24 kg, lastna masa: 6 kg, največja dovoljena obremenitev: 17 kg, velikost pnevmatike: 235 / 75 r 17,5, številka stroja/vozila: f8fb99947a1c19bc4d63549ff, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Crsdoi Riwfopfx Ad Ueh Rear foldable support 2 wheel chocks with holders Side underrun protection in aluminium Full-width rear mudflap Half-shell mudguards on the 1st axle with anti-spray mudflaps; anti-spray mudflaps behind 2nd and 3rd axles 1 plastic toolbox with shelf, dimensions: width 620 mm, height 360 mm, depth 440 mm, lockable with padlock (padlock not included) Extendable width up to 3,000 mm (not at rear slope) (track width of machines or vehicles to be transported must not exceed external frame width of 2,550 mm) Central storage compartment for timber planks on the loading platform 70 mm timber planks for widening to 3,000 mm Tie-down eyes for low-loader: 1 pair of flush-mounted ring lashing eyes at the front on the swan neck, each rated at 5t 7 pairs of lashing mushroom pins, recessed on top and sides of outer frame, each rated at 10t 1x front on swan neck 6x in low bed area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not more than 1,100 mm 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (convertible to 5t ring lashing eyes, not included) 2 additional pairs of foldable lashing eyes, each rated at 10t 1x on swan neck (protruding) 1x behind the last axle, recessed in the floor Drawbar assembly for turntable trailer: Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic springs with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker compensation) Wheels and Tyres 235/75 R 17.5 Manufacturer's choice, with M&S marking Steel rims in twin arrangement, factory silver finish Braking System 2-line compressed air braking system Spring-actuated parking brake 2 foolproof coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS socket at the front and connecting cable Brand: Wabco or Knorr Note: The trailer may only be towed by vehicles that ensure the proper functioning of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front 2 white/red lane departure lights at the rear 2x 7-pin foolproof plugs at the front with connecting cable 1 LED beacon with bracket, switched via parking lights (lamp removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Floor Front swan neck with steel chequer plate covering Storage box recessed in the approach slope to the swan neck Then 70 mm softwood flooring, in wheel arch area with steel chequer plate Rear slope with 70 mm softwood flooring Low-bed area incl. rear slope 6,500 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety device, foldable at the bottom (prevents lateral displacement of ramps, not in combination with laterally hydraulic ramp adjustment) Wooden covering Spring-assisted lifting support Operating Instructions At 10,000 kg axle load, a special permit is required, only indivisible loads allowed! The specified total weight is technically possible, but depending on the cargo, the total weight may not be achievable while complying with the permissible axle, support, and king pin loads (poor handling or tracking may result from incorrect load distribution) Country of Registration / Pla