Müller-Mitteltal Polpriklopniki nakup rabljenega (238)

Stanje: novo, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2025, * KA-TA-R 11.9 Masterline * Wabco EBS (electronic braking system) * RDÜ tire pressure monitoring system * Multivoltage * Emergency release device for spring brake cylinders * Drum brakes * 2 x 5.5 t BPW axles * Parabolic springs with tandem compensation unit * Drawbar adjustable in height by approx. 300 mm with 40 mm flange towing eye * Mechanical landing gear at front * Two mechanical folding supports at rear * Plastic toolbox, right side * 15-pin power connector * 12 V 13-pin auxiliary cable * Extended connection cables for forestry and agricultural towing vehicles * Two-stage access step, front left in direction of travel * LED tail lights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on sides and rear in the latches of the central locking; two units on the front wall Dcodpsq Euagofx Abmjr * Steel pallet 3-way tipper body (continuous side walls - without center stanchions - fold-down with drop side spring assist, tailgate fold-down and swinging via manual central locking) * One lashing ring (5 t) in each corner, and four lashing eyes (3 t each) recessed into the outer frame on each side * 4 mm steel floor plate * Mounting rail at rear for loading ramps * Reinforced body with EN 12642 XL load securing certificate * 1 pair aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable storage compartment, accessible from rear, recessed below the cargo platform in the chassis * Chassis, drawbar, tipping body, front wall, side walls, folding supports, as well as rear stanchions hot-dip galvanized; axles, springs, air tanks, flange towing eye, and landing gear painted in black * Tyres: 385/55 R 19.5 * New vehicle with manufacturer warranty * Sidewalls hot-dip galvanized * Subject to errors and prior sale * Immediately available from Egestorf

Stanje: rabljeno, največja dovoljena obremenitev: 8.100 kg, skupna masa: 11.000 kg, konfiguracija osi: 2 osi, prva registracija: 10/2008, dolžina tovornega prostora: 6.000 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Skupna masa: 11.000 kg Lastna masa: 2.900 kg Nosilnost: 8.100 kg Skupna dolžina: 8.100 mm Djdpfxjxtfkfo Abmocr Dolžina nakladalne površine: 6.000 mm Širina: skupna širina 2.550 mm / širina kesona 2.480 mm Nakladalna višina: pribl. 900 mm Dodatne informacije - Višina stranic: 400 mm - Lesena tla - Vzmetene rampe D: 2.700 mm Š: 600 mm - Nastavljiva višina ojnice - Pnevmatike 235/75 R17,5

Stanje: rabljeno, največja dovoljena obremenitev: 13.860 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, dolžina tovornega prostora: 6.770 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, prostornina tovornega prostora: 10 m³, Oprema: ABS, ? pocinkano podvozje ? nizko sklopljen ? vlečno oko 50 mm ? zaklep za kontejner ? po 12 pritrdilnih obročev na vsaki strani ? vzvratna kamera ? bobnaste zavore ? duomatski priključek ? ABS ? zračno vzmetenje ? orodjarna ? EBS Dcedpfxexb Ig Sj Abmsr ? podporne noge ? dvojna kolesa ? BPW osi Vse informacije brez garancije / Vmesna prodaja pridržana.

Stanje: rabljeno, skupna masa: 32.000 kg, konfiguracija osi: 2 osi, prva registracija: 01/2014, prostornina tovornega prostora: 10 m³, skupna širina: 2.500 mm, skupna višina: 4.000 mm, Oprema: ABS, For inquiries regarding the vehicle, Mr. Seidel will be happy to assist you (by phone at ...). ----MÜLLER MITTELTAL SF32BM/BT Concrete Mixer Semi-Trailer---- * Superstructure: Liebherr HTM 1004 10m³ * BPW axles * Drum brakes Dcodpfx Abswipfnjmor * Spring-loaded brakes * Wabco ABS * 1st axle liftable * Air suspension * Permissible total weight: 32,000 kg * Unladen weight: 6,510 kg * Payload: 25,490 kg * Tire tread depth: 1st axle 14-15 mm, 2nd axle 10 mm Upon request, we can provide you with a leasing or financing offer. Mr. Seidel (phone ...) will be happy to assist you. For more information, please visit our homepage. !!! Subject to errors, changes, and prior sale !!!

Stanje: rabljeno, skupna masa: 47.000 kg, konfiguracija osi: 3 osi, prva registracija: 11/2004, naslednji pregled (TÜV): 08/2026, * Müller Mitteltal TS3 nizkopodni polpriklopnik * Prva registracija: 11/2004 * 3 osi * Zračno vzmetenje * Gigant osi * Hidravlične dolge rampe, pomične in zložljive * Razširitve iz 2,50 m na 3,0 m širina nakladalnega prostora * Nakladalna dolžina: 8,50 m pri nakladalni višini 0,85 m * Nakladalna dolžina na vratu: 3,40 m pri nakladalni višini 1,50 m Djdpfxow Tgkbe Abmjcr * Podpore * Neto teža: 10.260 kg * Tehnično dovoljena skupna masa: 47.000 kg * TÜV veljaven do: 08/2026 * Tehnični pregled do: 02/2026

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Oprema: ABS, dvižna zadnja plošča, Inquiry number: 23185-O * Available immediately New Müller-Mitteltal KA-TA-R 11.9 tandem low-loader, three-way tipper trailer with ramps * Tyres: 385/55 R19.5 (4 pieces), BPW axles, parabolic springs, drum brakes * Gross weight: 11,900 kg, payload: 8,750 kg * Tyre pressure monitoring system with display option in the truck via EBS signal * EBS 24 volt * Side marker lights with integrated indicator function Dcjdpfsxmpd Asx Abmjr * LED lighting system for 12V and 24V * 2 LED reversing lights at the rear, suitable for 12V and 24V * Galvanized floor, 5m x 2.42m x 0.5m, laser-welded side walls, swinging, foldable, and removable, prepared for later retrofitting of side wall extensions * Stay wires for the tailgate * Lockable compartment under the tipping platform for loading ramp * Including aluminum ramps, 8 t load capacity, 3.57 m long, stored in the ramp shaft under the tipping body * Front wall hot-dip galvanized * 4 UVV lashing rings LC 5000daN front and rear + 8 recessed, foldable lashing eyes LC 3000daN in the tipper floor (centrally aligned) * Stepless height-adjustable towing bar, hot-dip galvanized, towing eye 40 mm * Net hooks * Bolted, galvanized rear stanchions * One plastic toolbox on the right side of the chassis frame * Access step in front of the front wall ---- * We are a Müller-Mitteltal distribution partner ---- * e.g. €5 net per day with 60 months term, no down payment, no final installment. An offer by our financing partner FM LeasingPartner * We will gladly send you a non-binding offer. ---- Our business hours Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside of business hours, we are available by appointment. Wir sprechen deutsch, we speak English, mowimy po polsku, on parle français, WhatsApp Leasing, financing, trade-in possible ----

Stanje: novo, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2025, * KA-TA-R 11.9 Masterline * Wabco EBS (Electronic Braking System) * RDÜ Tire Pressure Monitoring System * Multivoltage * Emergency release device for spring brake cylinders * Drum brakes * 2 x 5.5 t BPW axles * Parabolic springs with tandem equalizing assembly * Approx. 300 mm height-adjustable drawbar with 40 mm flanged towing eye * Mechanical landing gear at the front * 2 mechanical folding support legs at the rear * Plastic toolbox on right side * 15-pin electrical connector Djdpfx Abjl Thw Iomocr * 12V 13-pin auxiliary cable * Extended connection cables for forestry and agricultural towing vehicles * 2-step entrance on front left, in direction of travel * LED taillights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on the sides and rear in the central locking mounts, as well as 2 on the front wall * Steel pallet 3-way tipper body (continuous side walls without central stanchions – fold-down with sideboard spring lifts, rear flap foldable and swinging with manual central locking) * Each corner with 1 x 5 t lashing ring, plus 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm steel floor plate * Mounting rail at the rear for access ramps * Body reinforced with cargo securing certificate according to EN 12642 XL * 1 pair aluminum ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the load area at the rear embedded in the chassis * Chassis, drawbar, tipping body, front wall, side walls, folding supports, and rear stanchions hot-dip galvanized. Axles, springs, air tank, flanged towing eye, and landing gear painted in black * Tires: 385/55 R 19.5 * New vehicle with manufacturer’s warranty * Side walls hot-dip galvanized * Errors and prior sale reserved * Immediately available ex Egestorf

Stanje: rabljeno, lastna masa: 3.450 kg, največja dovoljena obremenitev: 14.550 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2010, naslednji pregled (TÜV): 07/2025, vzmetenje: zrak, velikost pnevmatike: 235/75R17.5, barva: rumena, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Oprema: ABS, Vehicle location: Bovenden, 2 axles, turntable trailer, air suspension, ABS (anti-lock braking system), container locking mechanism, underrun protection, side aluminum side guard, twin tires. Body: 2-axle outer roller trailer for roll-off containers from 5.5 m to 7 m or 2x 10 m³ skip containers, BPW axles, drum brakes, pneumatic locking, pneumatic lowering drawbar. ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors! Dcjdpfx Abexgilmemer

Stanje: rabljeno, največja dovoljena obremenitev: 13.860 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, dolžina tovornega prostora: 6.770 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 600 mm, prostornina tovornega prostora: 10 m³, Oprema: ABS, ? pocinkano ogrodje ? nizko spojeno ? vlečno uho 50 mm ? zaklep zabojnika ? po 12 priveznih obročkov na stran ? vzvratna kamera ? bobnaste zavore ? Duomatic priključek ? ABS ? zračno vzmetenje ? orodjarna Dcodpfx Aexb Igljbmjr ? EBS ? podporne noge ? dvojne pnevmatike ? BPW osi Vsi podatki brez garancije / vmesna prodaja pridržana.

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * Wabco EBS * RDÜ Tire Pressure Monitoring System * Emergency Release Device for Spring Brake Cylinders * Drum Brakes * 2 x 7 t Gigant Axles * Parabolic Springs with Tandem Equalizer Unit * Height-adjustable (approx. 300 mm), hot-dip galvanized drawbar with 40 mm flange towing eye * Jost Mechanical Landing Gear at the front Dcjdpfx Absl Th A Eemsr * Rear: 2 mechanical, hot-dip galvanized folding supports * 15-pin Power Connector * LED Tail Lights * Hot-dip galvanized, bolted underride protection * Toolbox made of galvanized sheet steel, side right * Plastic Quarter Mudguards * Hot-dip galvanized chassis * Steel Pallet 3-way Tipper Body * Continuous side walls, upper section with internal tubular reinforcement - no intermediate stakes - foldable with side board spring assist * Rear tailgate foldable and swivable, with manual central locking * Hot-dip galvanized, bolted rear stanchions * Each corner equipped with 1 x 5 t lashing point as well as 4 x 3 t lashing rings recessed into the outer frame on each side * 4 mm Fine Grain Steel Floor Plate * Net hooks, rear mounting rail for loading ramps * Preparation for retrofitting side board extensions * Body reinforced and certified for load securing according to EN 12642 XL * 2-step access step on the left side as climbing aid * 1 pair of aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable rear storage compartment integrated into the chassis below the loading area * Axles, springs, air tank, and landing gear painted in black * Chassis, drawbar, floor, front wall, and folding supports hot-dip galvanized * New vehicle without initial registration, with manufacturer’s warranty * Tires 385/55 R 22.5 * Sideboard painted in RAL 9010 pure white * Side wall painting in any RAL color available at extra cost * Subject to errors and prior sale * Available from calendar week

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * Wabco EBS (Electronic Braking System) * RDÜ Tire Pressure Monitoring System * Emergency Release Device for Spring Brake Cylinders * Drum Brakes * 2 x 7 ton Gigant Axles * Parabolic Springs with Tandem Equalizing Unit * Height-adjustable hot-dip galvanized drawbar, approx. 300 mm, with 40 mm flanged towing eye * Jost Mechanical Landing Leg at the Front * 2 Mechanical Hot-dip Galvanized Folding Support Legs at the Rear * 15-pin Power Connector * LED Rear Lights * Hot-dip Galvanized, Bolted Underrun Protection * Toolbox on Right Side Made from Galvanized Sheet Steel * Plastic Quarter Mudguards * Hot-dip Galvanized Chassis * Steel Pallet – 3-way Tip Body * Continuous Side Walls at the Top with Internal Tube Reinforcement – without central stakes – foldable with drop-side spring lifter * Rear Tailgate Foldable and Swinging via Manual Central Locking * Hot-dip Galvanized, Bolted Rear Stakes * 1 x 5-ton Lashing Point in Each Corner and 4 x 3-ton Lashing Rings Recessed into the Outer Frame on Each Side * 4 mm Sheet Floor Made of Fine Grain Steel * Net Hooks, Rear Mounting Rail for Loading Ramps * Preparation for Subsequent Installation of Drop-side Extensions * Body Reinforced with Load Securing Certificate According to EN 12642 XL * 2-step Climbing Aid on the Left Side * 1 Pair of Aluminium Loading Ramps approx. 3,570 x 400 mm (Load Capacity 8 tons/pair), suitable for rubber-tired and tracked vehicles * Lockable Storage Compartment under the Loading Area Integrated into the Chassis, Accessible from the Rear * Axles, Springs, Air Tank, and Landing Leg Painted Black * Chassis, Drawbar, Floor, Front Wall, and Folding Supports Hot-dip Galvanized * New Vehicle without Initial Registration, with Manufacturer’s Warranty * Tyres: 385/55 R 22.5 * Drop-side Panels Painted in RAL 9010 Pure White * Painting of Side Walls in an RAL Colour Tone Available at Extra Cost Dsdpfx Absv Dz N Nsmjcr * Errors and Prior Sale Reserved * Available from Week [KW]

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * Wabco EBS (Electronic Braking System) * RDÜ (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer * Approx. 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flange towing eye * Jost mechanical landing gear at the front * Rear: 2 mechanical hot-dip galvanized folding supports * 15-pin electrical connector * LED tail lights * Hot-dip galvanized bolted underrun protection * Toolbox made of galvanized sheet steel, right side * Plastic quarter mudguards * Hot-dip galvanized chassis Dcsdpfx Absv El Tusmjr * Steel pal. 3-way tipper body * Continuous side walls at the top with internal tube reinforcements, without central stanchions, can be folded down, with drop side spring assists * Rear tailgate foldable and swing-mounted, secured by manual central locking * Bolted hot-dip galvanized rear stanchions * Each corner with 1 x 5 t lashing point and each side with 4 x 3 t lashing rings integrated into the outer frame * 4 mm fine-grain steel floor plate * Net hooks, mounting rail at the rear for loading ramps * Preparation for retrofitting drop side extensions * Body reinforced with load securing certificate according to EN 12642 XL * 2-step access on the left side as step-up aid * 1 pair aluminium loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable from the rear: storage compartment mounted below the loading area, integrated into the chassis * Axles, springs, air tanks and landing gear painted in black * Chassis, drawbar, floor, headboard, folding supports hot-dip galvanized * New vehicle without initial registration, with manufacturer’s warranty * Tires 385/55 R 22.5 * Side walls painted RAL 9010 pure white * Painting of side walls in an RAL color tone available for surcharge * Errors and prior sale subject to change * Available from calendar week

Stanje: novo, največja dovoljena obremenitev: 23.500 kg, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.380 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2024, * PT 30 Profile: * EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lift and lowering function as well as RtR valve * Smart-Board mounted on trailer as information tool (separate axle load indication front and rear) * Tyre pressure monitoring with display option in the truck via EBS signal, no installation required on the truck side * Side underrun protection Dodpfx Ajxptn Robmocr * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning board packages front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight, galvanised steel sheet skirts with spray protection * Contour marking tape, reflective on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment by means of draw spring & turnbuckle * Tool box, galvanised steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted on right side * Accessory box in turntable with folding lid, 2 built-in container locks (immediately behind turntable platform) * ROBOT-welded anti-slip coating on turntable platform steel plate (protruding weld seams) * Load securing package consisting of: 2 lashing rings (13.4 t) front left & right on front wall support, front & rear 1 pair UVV lashing rings (13.4 t) as well as 3 pairs each side UVV lashing rings (10 t), swivelling and lowerable, loadable in all directions and recessed in outer frame, each side 3 stanchion pockets with simultaneous 2 t lashing capacity * 6 pairs mechanical folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stored in the centre of the load area * Hydraulic one-piece ramps approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way control block for later retrofitting of hydraulic ramp shifting * Chassis, turntable, folding outriggers, drop supports and approach ramps hot-dip galvanised * Axles, slewing ring, air tanks, drawbar painted in a shade of black * Loading edge height (laden): approx. 910 mm +/- 20 mm air suspension * New vehicle with manufacturer’s warranty * Subject to prior sale and errors * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T5 profile 50.0: * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Last axle steering (axle lock for manoeuvring can be activated from the cab without additional truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension, lift and lowering system with RtR valve * 3rd axle liftable (ride height +30 mm with lifted axle) * Forced relief and forced lowering of the lift axle for manoeuvring (requires truck-side installation), speed-dependent activation via EBS * Smartboard infotool with pressure sensors for total axle load display per axle group * TPMS with display option in the truck via EBS signal (no truck-side installation required) * Mechanical warning sign kit for 3m total width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable rear LED beacon * Toolbox, galvanised steel approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle, galvanised steel mud guards rear axle * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to rear) * Shortened low-loader deck by 500 mm to 6,280 mm incl. extended step by 500 mm to the front * Load securing package: 2 x 6.4 t lashing rings front corners, side front & rear corners each 2 x 13.4 t UVV lashing rings, 5 x 10 t UVV lashing rings per side (pivoting/lowering and loadable in all directions), 4 stake pockets per side additionally providing 2 t lashing option, 1 x 16 t UVV lashing ring on rear traverse * Rubber matting on folding ramp, approach slope, and low loader running surface * Bamboo wood inserted between main beams in excavator arm storage area * Extendable and folding outrigger extensions for 3 m total width (beam holder under chassis, right side) * Continuous excavator arm storage with reinforcement profile from last axle to rear cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs 6.4 t UVV lashing rings on sides * Hydraulic folding ramp with dual-line hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift * Hydraulic rear support * Hydraulic flow divider (for truck hydraulic capacity over 40 l/min up to 140 l/min) * Loaded platform height 890 mm +/- 20 mm (via air suspension) * Platform above turntable: 2,600 + 390 x 2,520 mm Djdpfx Aboxptn Djmocr * Low-bed platform: 6,280 + 500 x 2,520 mm incl. 860 mm approach ramp * Chassis, turntable, drawbar, extension consoles, and access ramps hot-dip galvanised * Drawbar, axles, hydraulic axle supports, and air tanks painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 14/2026

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 24.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * RDÜ (tyre pressure monitoring system) * Drum brakes * 3 x 11 t Gigant axles * Air suspension with manual rear lowering * Mid-axle liftable * Pneumatically lowerable drawbar, 2,100 mm long with 50 mm towing eye & height adjustment device * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right side * Side and rear contour marking tape, reflective * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact bumpers * LED tail lights * 15-pin power connector Dcjdpjpk D Awsfx Abmsr * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll containers * Steel floor with roller recesses in bogie area * For roll-off container transport, container lengths from 5,500 – 7,000 mm possible * Pneumatic 4-point clamp locking and mechanically insertable stop angles at front in guide rails * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * 8 relocatable skip stops for lateral centering of skips, front 4 stops plug-in with pivoting restrictor * 3 pairs of 10 t UVV lashing rings at the sides for attaching tensioning devices for positive and friction-locked securing of the skips * 4 lashing bars each in clover-leaf design (side) and 1 pair of 13.4 t UVV lashing rings at front * Load securing certification according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Weld bead as anti-slip coating in the running rail area of the ramp * Mechanical drop supports at rear * 1 pair of aluminium loading ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment at rear) * Tyres: 235/75 R17.5 * Loaded ride height approx. 1,003 mm * Payload 18,900 kg * Gross vehicle weight technically possible up to 27,000 kg * Axles, turntable, drawbar and air tanks painted in black * New vehicle without first registration, including manufacturer’s warranty * Subject to errors and prior sale * Available from calendar week 50/2025

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 24.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-actuated cylinders * TPMS (tire pressure monitoring system) * Drum brakes * 3 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Center axle can be lifted * Pneumatically lowerable drawbar, 2,100 mm long with 50 mm towing eye & height adjustment device * Tool box made of powder-coated sheet steel as well as basket-type spare wheel holder on the right side * Reflective contour marking tape on the sides and rear * Side underrun protection * Plastic quarter mudguards with spray guard * Plastic rear impact protection buffer * LED rear lights * 15-pin power connector * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for container guidance Dsdpfxopk D Iij Abmjcr * Sheet steel floor with roller recesses in bogie area * For roll-off container transport, container lengths from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking and mechanically inserted stop angles at the front in the track section * Load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Including 8 repositionable skip stops for lateral centering, the front 4 skip stops are inserted with oscillating stops * 3 pairs of 10 t UVV lashing rings on the sides for securing chains/straps by positive and frictional connection * 4 cloverleaf lashing brackets on each side and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certification as per DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Weld bead as anti-slip surface in the drive-up slope area * Mechanical drop-down supports at the rear * 1 pair of aluminium approach ramps (16 t per pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) * Tyres 235/75 R17.5 * Ride height loaded approx. 1,003 mm * Payload 18,900 kg * Technically permissible total weight of 27,000 kg * Axles, turntable, drawbar and air tanks painted black * New vehicle, unregistered, with manufacturer’s warranty * Subject to prior sale and errors * Available from calendar week 50/2025

Stanje: novo, največja dovoljena obremenitev: 38.900 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T5 profile 50.0: * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Last axle steering (axle lock for manoeuvring can be activated from the cab without additional truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension, lift and lowering system with RtR valve Dcodjl Tihujpfx Abmer * 3rd axle liftable (ride height +30 mm with lifted axle) * Forced relief and forced lowering of the lift axle for manoeuvring (requires truck-side installation), speed-dependent activation via EBS * Smartboard infotool with pressure sensors for total axle load display per axle group * TPMS with display option in the truck via EBS signal (no truck-side installation required) * Mechanical warning sign kit for 3m total width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable rear LED beacon * Toolbox, galvanised steel approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle, galvanised steel mud guards rear axle * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to rear) * Shortened low-loader deck by 500 mm to 6,280 mm incl. extended step by 500 mm to the front * Load securing package: 2 x 6.4 t lashing rings front corners, side front & rear corners each 2 x 13.4 t UVV lashing rings, 5 x 10 t UVV lashing rings per side (pivoting/lowering and loadable in all directions), 4 stake pockets per side additionally providing 2 t lashing option, 1 x 16 t UVV lashing ring on rear traverse * Rubber matting on folding ramp, approach slope, and low loader running surface * Bamboo wood inserted between main beams in excavator arm storage area * Extendable and folding outrigger extensions for 3 m total width (beam holder under chassis, right side) * Continuous excavator arm storage with reinforcement profile from last axle to rear cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs 6.4 t UVV lashing rings on sides * Hydraulic folding ramp with dual-line hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift * Hydraulic rear support * Hydraulic flow divider (for truck hydraulic capacity over 40 l/min up to 140 l/min) * Loaded platform height 890 mm +/- 20 mm (via air suspension) * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm incl. 860 mm approach ramp * Chassis, turntable, drawbar, extension consoles, and access ramps hot-dip galvanised * Drawbar, axles, hydraulic axle supports, and air tanks painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 14/2026

Stanje: novo, največja dovoljena obremenitev: 27.940 kg, skupna masa: 36.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function, including RtR valve * Start assist for shunting, applied to first axle via EBS – no truck-side installation – when lift axle is raised +30 mm ride height * Smart-Board installed on trailer as an info tool, with pressure sensors for total axle load indication * Rear axle as self-steering axle with electro-pneumatic steering lock * Steering lock for trailing axle controlled from driver’s cab for maneuvering purposes via EBS (no truck-side installation) * 2" king pin * 1 lift axle * Side underrun protection * Front aluminium drop support legs and rear swing-down supports on chassis * Alcoa LVL One aluminium wheels * 15-pin electrical connector * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 2 LED work lights mounted on trailer sides – no truck-side installation * 7-pin power socket at rear for overlength lighting Dedowh Hdxspfx Abmjcr * Side marker lamps with indicator activation * Tyre pressure monitoring system with display in truck via EBS signal (no truck-side installation) * Mechanically adjustable warning sign sets front and rear * Straight steel fenders * Saddle platform with 45° bevelled front corners and front toolbox made of galvanized, powder-coated steel sheet (B = 2,480 x H = 500 x L = 665 mm), top hinged lid and side doors at the beveled corners * 400 mm aluminium side boards (RAL 9010 pure white) fold-down and removable, mounted laterally on the saddle platform * Rear wall –150 mm– slotted in * Tapered rear on the saddle platform to lowbed approx. 700 mm long with chequer plate covering and lashing bar at end for attaching aluminium ramps * Saddle and lowbed platform with 50 mm clamped wooden planks * Tear plate above the axles * Prepared for 3 mounting shafts under the saddle platform for optional aluminium ramps storage * Swing arm as a carrier for connection lines from truck to trailer * Load securing package consisting of: outer frame of the saddle platform with punched holes, 45° bent and hole-pattern for lashing devices (2 t lashing force per point, min. 480 mm spacing), side-mounted 2 x 6.3 t recessed lashing rings per side, 1 x 16.5 t lashing ring per side at incline from lowbed to saddle platform, 2 pairs 16.5 t lashing rings in lowbed (1x on longitudinal beams after the step, 1x above the centre axle beside longitudinal beam), side 3 x 13.4 t lashing rings per outer frame (1x at start of platform step, 1x start of ramp slope, 1x end of ramp slope), 3 x 10 t each side (2x between front wheel recess and 1st axle, 1x between 2nd and 3rd axle), 3 x 5 t per side screwed to the wheel recess outer frames (2 at front, 1 at rear recess) * Extended excavator arm trough from end of last rigid axle over steering axle to end cross member, continuous with internal reinforcement profile approx. W = 770 mm x D rear = 270 / D front = 170 mm; each side 2 x 6.4 t lashing rings in the arm trough * Each side two wheel recesses, 390 mm deep and 640 mm wide for transporting wheel loaders with wheelbase 3,000–3,590 mm, tyre diameter up to 1,760 mm – retractable covers – * Second retractable cover ...

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no truck-side installation required * Height-adjustable towing bar (up to 300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front * Two mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, right side * 15-pin electrical connector * Multi-chamber tail lights * Bolted underrun protection * Plastic quarter mudguards * Net hooks on the sides and rear in the central locking mounts, plus two on the front wall * Main frame made of fine-grained steel * Steel pallet tipper body with rigid front wall made of smooth plate, continuous side walls – foldable without intermediate stakes, with drop side spring assist and with pendulum function via manual central locking * Bolted rear stanchions * Steel rear wall inserted in front of the ramps * Each corner with 1 x 5 t lashing point, plus 4 x 3 t lashing rings recessed in the outer frame on each side * 4 mm floor made of fine-grained steel * Two-part mechanical grid ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) Dcsdpstr St Hefx Abmor * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop supports, as well as ramps, hot-dip galvanized * Axles, springs, air reservoir, flange towing eye and landing gear painted in black tone * Side walls and platform in RAL 9010 pure white * Painting of side walls and tipping platform in a RAL color of choice available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Flatbed: * Tire Pressure Monitoring System (TPMS) * EBS (Electronic Braking System) * Emergency Release Device for Spring Brake Cylinders * Drum Brakes * 2 x 7 t BPW Axles * Air Suspension with Lifting and Lowering System * Mechanically Adjustable 3 m Warning Sign Boards at Front and Rear * Towbar Height Adjustable by 300 mm, with 40 mm Flange Eye * Drawbar Shortened by approx. 200 mm to approx. 1,800 mm (Resulting in a B-Dimension of approx. 8,080 mm) * Front Landing Leg * Outward Folding Rear Support Legs * Plastic Toolboxes approx. 750 x 350 x 300 mm each, mounted on both the left and right sides * Side Impact Protection * Rear Underrun Protection * Plastic Quarter Mudguards * 15-Pin Electrical Socket * LED Lighting System 12 / 24 V * 2 Additional LED Reversing Lights at Rear (controlled via reverse gear) * 1 Removable LED Beacon (including bracket) at the rear * 400 mm high bolted front wall * 50 mm Softwood Floor * 2 Pairs of Container Locks (extendable to 3 m container external width) and lockable, locking dimension retracted per ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) for an overall external width of 3,000 mm * Perforated outer frame bent at approx. 45° with 2 t lashing capacity every 480 mm, installation of 3 t folding lashing rings possible every 600 mm – with 5 x 3 t UVV lashing rings fitted per side –, in each front and rear corner 1 x 6.3 t lashing ring (front, directly behind the container locks in the timber floor, and rear in the end cross member), various holes for 1.2 t lashing options in the front and rear cross members * 1 Pair of Aluminium Slide-In Ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated into the chassis beneath the loading area * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing leg, and flange tow eye painted in black Dcsdpfx Abev D Tbksmsr * New vehicle with manufacturer’s warranty * Subject to prior sale and errors * Available from calendar week 09/2026

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with display capability in the truck via EBS signal - no on-truck installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool mounted with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed individual plastic mudguards * Rear straight steel mud flaps each with spray suppression * Lateral underrun protection * Front section ahead of the turntable platform extended approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (folding lids open to the rear) * Chassis made of high-strength fine-grained steel * Floor over the turntable platform made of 50 mm and in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing rings 6.4 t front left and right on the main frame of the turntable platform, 1 pair of 13.4 t lashing rings per side at the front and rear on the outer frame, plus 1 pair of 10 t lashing rings per side swivel- and lowerable, loadable in all directions and recessed in the outer frame, bolted 5 t lashing rings to the outer frames of wheel recesses (2 for the front and 1 for the rear wheel recess), 2 pairs of 6.4 t lashing rings at the side in the excavator arm recess * 11 pairs of folding outriggers for 3 m overall width (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the extension boards made of sheet steel, mounted across the loading area in front of the 1st rear axle * Excavator arm trough above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side, approx. 640 mm wide - front 340 mm deep, rear 220 mm deep - with retractable cover (storage for covers at the front of the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm Dcjdoxmpydjpfx Abmsr * Hydraulic lateral ramp shift * Load platform above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded platform height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear drop-down supports and loading ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from CW 14/2026 * Sample images

Stanje: novo, največja dovoljena obremenitev: 30.500 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages at front and rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on sides and rear * Removable LED beacon at rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Closed molded plastic single fenders at front * Straight steel rear fenders each with spray suppression (ant-splash) * Side underrun protection * Extension in front of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lids open rearwards) * Chassis made of high-tensile fine-grained steel * Floor above turntable platform from 50 mm softwood, in low-bed platform from 60 mm softwood * Outer planks of ramps from 50 mm hardwood * Load securing package consisting of: 2 lashing eyes (6.4 t) at front left and right on main frame of turntable platform, 1 pair of lashing rings (13.4 t) at front and rear on side outer frame each, 1 pair of lashing rings (10 t) each side, pivoting and lowerable, loadable in all directions, recessed into the outer frame, 5 t lashing rings bolted to the outer frames at wheel recesses (2 each at front wheel recess, 1 at rear), 2 pairs of 6.4 t lashing rings at the excavator arm rest on the side * 11 pairs of folding outriggers for 3 m overall width (not in rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for ramp extension planks, made from sheet steel, transversely mounted in front of 1st rear axle * Excavator arm rest above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side approx. 640 mm wide (front 340 mm deep, rear 220 mm deep) with slide-in covers (covers storage at front on turntable platform) for transporting wheel loaders with wheelbase 3,100–3,640 mm * Mechanical drop-down supports at rear * Hydraulic folding ramps with hydraulically extendable tip part approx. 4,650 x 720 mm * Hydraulic lateral ramp displacement * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded loading height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear supports, and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle fully hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 14 of 2026 * Sample images Dedpfx Aoxmpykjbmecr

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Tire pressure monitoring system with display capability in the truck via EBS signal, no installation required on the truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical landing gear at the front * Rear: 2 mechanical folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lamps * Bolted underrun protection * Plastic quarter mudguards * Mesh hooks on the sides and rear in the central locking mounts, plus 2 hooks on the front wall * Main frame made of fine-grain steel * Steel pallet - 2-way tipper body, fixed front wall made of smooth sheet, continuous side walls (foldable without center stanchions, with drop-side spring assist mechanism), pendulum-type operation via manual central locking * Rear stanchions are bolted * Steel rear wall slides in front of the ramps * In each corner: 1 x 5 t lashing point; additionally, 4 x 3 t lashing rings each side, integrated into the outer frame * 4 mm floor made of fine-grain steel * Two-piece mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) Djdpstr Sucsfx Abmscr * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop-down supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * Drop sides and platform in RAL 9010 pure white * Painting of side walls and tipping platform in any RAL color available for extra charge * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from CW 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.400 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem compensation unit * Tire pressure monitoring with display capability in the truck via EBS signal, no installation required on truck side * Height-adjustable drawbar (300 mm) with 40 mm flange towing eye * Mechanical support winch at the front * Rear: 2 mechanical foldable supports * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks on sides and rear, integrated in the central locking bearings, plus 2 units on the front wall * Main frame made of fine-grain steel * Steel pallet 2-way tipper body with fixed smooth sheet front wall, continuous foldable side walls (without center stanchions, with sideboard spring lifters and manual central locking for swinging function) * Removable screw-on rear stanchions * Steel rear wall mounted in front of the ramps * In each corner: 1 x 5 ton lashing point; in each side: 4 x 3 ton lashing rings integrated into the outer frame Dcjdpfxjtr St Ue Abmjr * 4 mm floor made of fine-grain steel * Two-part mechanical grating loading ramps with aluminum tapered end, 2,150 + 1,300 mm x 600 mm (retractable to 80 mm manually) * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Side boards and platform in pure white, RAL 9010 * Painting of side walls and tipper platform in any RAL color available at additional cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Platform: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7-ton BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3-meter warning panel sets, front and rear * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B-dimension approx. 8,080 mm) * Landing gear/winch at the front * External foldable rear support legs * Plastic toolboxes approx. 750 x 350 x 300 mm each, on left and right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lighting system, 12 / 24 V * 2 additional LED reversing spotlights at the rear (wired via reverse gear) * 1 removable LED beacon (incl. bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m exterior container width) and lockable; locking dimension retracted according to ISO-DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) with a total exterior width of 3,000 mm * Perforated outer frame, approx. 45 degree angled, with 2 t lashing capacity every 480 mm, possible installation of 3 t folding lashing brackets every 600 mm – on each side, 5 x 3 t UVV lashing brackets installed –, at each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end crossmember), various holes for 1.2 t lashing options in the front wall and end crossmember * 1 pair of aluminum insert ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear storage compartment integrated below the loading area in the chassis * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing gear, and flange eye painted in black * New vehicle with manufacturer warranty * Subject to errors and prior sale Dcedjv D Tbdjpfx Abmjr * Available from week 09/2026