Müller-Mitteltal Struktura Silosa nakup rabljenega (257)

Stanje: novo, največja dovoljena obremenitev: 31.900 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release for spring-actuated cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lowering function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and continuously adjustable height ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck dashboard via EBS signal – no installation required on truck * SmartBoard as infotool with pressure sensors for axle load display per axle group * 15-pin power connector * LED taillights * Removable LED beacon at rear ----General attachments: * Warning plates front & rear * 2 x toolboxes made of galvanized, powder-coated sheet steel approx. 650 x 300 x 600 mm, right side * Closed single plastic mudguards at front * Straight steel spray suppression panels at rear, each with spray suppression * Side underrun protection ----Low-bed platform: * Turntable/platform extension by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and lockable * Flooring on turntable platform made of 50 mm softwood; on low-bed platform made of 60 mm softwood * 20 mm rubber covering instead of timber in drive lane area with a well length of 6,780 mm including sloped ramp * Rubber coating on the ramp left and right, approx. 860 mm length * 4 stake pockets per side (stakes not included) with simultaneous 2 t lashing point capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load securing (Lasi package): Turntable/platform: * 2 pairs of 13.4 t lashing eyes in outer frame of turntable/platform Low-bed: * 4 pairs of 10 t lashing rings per side on the outer frame, foldable and loadable in all directions Duedpfx Adoylfvgjqor * 2 pairs of 13.4 t swiveling lashing rings at rear on each side ----Ramps: * Rubber covering on foldable access ramps * Hydraulic folding ramps with hydraulic tip extension approx. 4,650 x 720 mm * Hydraulically lateral ramp shift & load-holding valves ----Rear support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for 3 m overall width (not on rear bevel) * Widening boards stowed on left side compartment ----Excavator boom trough: * Excavator boom trough above rear axle to end of slope approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4 t lashing rings at sides in excavator trough ----Hydraulics: * Hydraulic flow divider in trailer (for truck hydraulic pump outlet above 40 up to max. 120 ltr./min.) ----Loading dimensions: * Rear loading platform: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Platform above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour tape at sides and rear * Chassis, turntable, access ramps and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks and turntable painted in black tone ----Info: * New vehicle with manufacturer warranty * Errors and prior sale reserved * Sample images may show special equipment ----Lead time: * Vehicle available from approx. week 23/2026

Stanje: rabljeno, lastna masa: 8.800 kg, največja dovoljena obremenitev: 31.200 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/1996, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.510 mm, višina nakladalnega prostora: 1 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75R17.5, barva: rdeča, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Lokacija vozila: Bovenden, 4 osi, vrtljiva gred, listnato vzmetenje, razširljiv do 3 m, pritrdilna ušesa, dvo-delne nakladalne rampe, hidravlične rampe, zadnja podpora, stranska aluminijasta zaščita, dvojne pnevmatike, škatla za orodje. Nadgradnja: 4-osna nizkopodna prikolica s hidravličnimi dvodelnimi rampami. Višina nakladanja cca 900 mm. 4x SAF osi 10t, bobnaste zavore, vlečno uho 40 in 50 mm! Dolžina zgornje ploščadi cca 2900 mm! Dolžina spodnje ploščadi cca 7100 mm! PODATKI O DODATNI OPREMI BREZ GARANCIJE, spremembe, vmesna prodaja in napake pridržane! Dodpfoywvhrex Adqjur

Stanje: rabljeno, največja dovoljena obremenitev: 16.950 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2006, naslednji pregled (TÜV): 04/2026, Leto izdelave: 2006, * Müller Mitteltal T3 NG Dusdpeyv Ug Djfx Adqjr * Low-loader * Ramps * Twin tires * Permissible total weight: 24,000 kg * Unladen weight: 7,050 kg * Payload: 16,950 kg * Tires: see pictures * BPW axles * Immediately available * Errors excepted We offer: Net purchase for companies from the EU with a VAT ID number, as well as for customers from non-EU countries. Leasing and financing available. Handling of all customs formalities. Issuance of short-term and export registration plates. Transport to port. All prices listed on classified ad platforms are gross prices and already include the statutory VAT of 19%.

Stanje: rabljeno, največja dovoljena obremenitev: 19.800 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, prva registracija: 01/2019, Oprema: ABS, * Müller Mitteltal 3-osna prikolica za zabojnike za odpad * Tip TM 2 24 * Za dva zabojnika za odpad od 7 do 10 m³ * Zavarovanje tovora s samo dvema verigama na zabojnik * Dvojne pnevmatike 265/70 R19,5 * Zračno vzmetenje * BPW osi * Vrtljivo vlečno uho pnevmatsko znižljivo s pnevmatskim sproščanjem * 8 UVV pritrdilnih obročev 5t za pritrditev napenjalnih elementov Duodpfxsyx R Enj Adqjr * 8 premakljivih omejevalnikov zabojnikov za bočno centriranje zabojnikov * EBS * Tehnično dovoljena skupna masa 27.000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, Leto izdelave: 2002, Kiper-nizkopodni kombi. Dozvoljena ukupna masa 10.500 kg, nosivost 7.550 kg. Trosmerna kiperska nadogradnja, dimenzije otprilike 5.000 x 2.420 x 400 mm (unutrašnje), 4 ušice za vezivanje tereta, bočne stranice od čelika, viseće i preklopne, sa centralnim zaključavanjem. 1 par aluminijumskih utovarnih rampi u bravom zaključanim pregradama ispod sanduka kipa. Visina utovara u praznom stanju oko 900 mm. Dvostepena potporna noga napred, sklopive zadnje potpore. Vučna kuka prečnika 40 mm, vučna ruda sa besprekornim podešavanjem visine. Dvovodna pneumatska kočnica, jednovodna hidraulika, 24 V. BPW osovine, parabolične opruge, ABS. Pneumatici 235-75R17.5. Šasija siva, kip most zelene boje. Tehnički pregled važi do juna 2026. Prodaja u viđenom stanju. Aluminijumske rampe = Dodatne informacije = Vlastita masa: 2.950 kg Dujdpfxjyw Hw Re Adqjr Nosivost: 7.550 kg Dozvoljena ukupna masa: 10.500 kg Pneumatici napred: 235-75R17.5 Pneumatici nazad: 235-75R17.5 Zemlja porekla: Nemačka Kontakt osoba: Jan-Marc Schwickert za dodatne informacije.

Stanje: novo, največja dovoljena obremenitev: 8.770 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, * Müller-Mitteltal ETÜ-TA-R 11.9 Low Loader Tandem Trailer/Ramps Dodpfxoyxbdbs Adqsur * BRAND NEW vehicle with no initial registration, * Available mid/end of May ’26 in RAL 7016 anthracite, Reference number for inquiries: 30504 * GVWR: 11.9 t, Payload: 8.77 t * Reinforced and certified superstructure according to EN 12642 XL including load securing certificate * 6.27 m x 2.47 m x 0.4 m laser-welded steel side walls, foldable with 2 spring assistors * Front wall bolted smooth sheet metal (hot-dip galvanized) * Rear wall: (hot-dip galvanized) slides in front of ramps with storage holder behind front wall * Bolted rear stanchions (hot-dip galvanized) * 50 mm thick softwood floor * 4 UVV lashing rings LC 6300 daN, recessed front and rear in crossmember * 10 UVV lashing shackles LC 3000 daN recessed in existing hole pattern on outer frame * Ramps: one-piece hot-dip galvanized grating with anti-slip design * Pre-installed bracket for retrofitting container locks in front of the front wall * Plastic toolbox in front of the front wall * Chassis and drawbar (hot-dip galvanized) * 235/75 R17.5 (dual tires), parabolic springs * BPW axles with tire pressure monitoring * EBS 24 Volt * Height-adjustable drawbar (hot-dip galvanized) with 40 mm towing eye * 2 LED reversing lights at the rear of the trailer * LED lighting system for 12V + 24V * Side marker lights with indicator control * 1 removable LED rotating warning beacon including holder and installation ---- * Trade-ins possible * Financing via our partners with or without down payment or final installment and various terms available. Request your tailored offer! ---- * Example installment lease from our partner FM LeasingPartner: €475/month net for 60 months, no down payment, and zero final payment. Other terms, with or without down payment/final installment, are also possible. Request your offer! We are official Müller-Mitteltal distributor! ---- * Our business hours: * Monday – Thursday: 08:00 – 17:00 * Friday: 08:00 – 15:00 * Outside these hours we are available by appointment * Wir sprechen Deutsch, we speak English, ????? ?? ????? ?????, Mowimy po polsku, on parle français.

Stanje: rabljeno, lastna masa: 3.210 kg, največja dovoljena obremenitev: 8.690 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 05/2021, naslednji pregled (TÜV): 06/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17.5, Leto izdelave: 2021, Oprema: ABS, Nemško vozilo MASTERLINE Müller-Mitteltal KA-TA-R 11,9 trosmerni kiper sa rampama ispod utovarene Godina prve registracije: 05/2021 pocinkovan Dozvoljena ukupna masa: 11.900 kg Sopstvena masa: 3.210 kg Nosivost: 8.690 kg Dedpsyxbgcefx Adqsur Dimenzije pneumatika: 235/75 R 17,5 Tandem osovina manja od 1 m Vučna ruda je neprekidno podesiva po visini, toplo pocinkovana, vučna kuka 40 mm Ram pocinkovan BPW osovine Visina poda: 0,93 m Dodatne usluge dostupne! Izvozne tablice (crvene / 30 dana) Nemačka Kratkoročne tablice (žute / 5 dana) Nemačka Moguća organizacija austrijskih prevoznih tablica Isporuka vozila (uz nadoknadu) Podaci dati na internetu su nezahtevne informacije. Ne predstavljaju zagarantovana svojstva. Prodavac ne preuzima odgovornost za greške, tipografske greške i greške u prenosu podataka. Prodaja uz mogućnost prethodne prodaje. Prodaja isključivo privrednim subjektima. Važe isključivo naši Opšti uslovi poslovanja.

Stanje: skoraj kot novo (rabljeno), Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WMM000000L0066323, lastna masa: 2.980 kg, največja dovoljena obremenitev: 7.020 kg, skupna masa: 10.000 kg, konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 10.000 kg, dolžina tovornega prostora: 5.350 mm, širina tovornega prostora: 2.450 mm, višina nakladalnega prostora: 800 mm, skupna dolžina: 7.498 mm, skupna širina: 2.550 mm, stanje pnevmatik: 95 odstotek, barva: bela, zavoro prikolice: prikolica s zavoro, Leto izdelave: 2021, Oprema: ABS, Prikolica kot nova Prodaja brez jamstva / garancije Dedpoyt Igkefx Adqeur Napake in vmesna prodaja pridržane! Podatki v tem oglasu so neobvezni opisi in ne predstavljajo zagotovljenih lastnosti. Prodajalec ne prevzema odgovornosti za napake pri vnosu ali prenosu podatkov. Oprema navedena v oglasu se preverja posebej. Vse navedene informacije v oglasih so neobvezne!

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 18.0: * 3 in 1 = for roll-off, skip containers, and as a low loader ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm towing eye with height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS, indicator can be viewed in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Tool box made of powder-coated sheet steel, right side * Side underride guard * Plastic quarter mudguards with splash protection * Storage box for container nets made of galvanized sheet steel, approx. 960 x 300 x 400 / 450 mm, right side * Plastic rear impact protection buffer * Mechanical rear drop supports ----Loading Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll-off containers * Steel floor with wheel depressions in the bogie area * For roll-off container transport, container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp lock and mechanically insertable stop angles at the front in the guide rail, load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 removable skip stops for lateral centering, front 4 skip stops are insertable with swiveling stops * Weld bead as anti-slip coating in the ramp area of the run-up slope Dodpfel Thwcox Adqsur ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for securing the skips with lashing elements (positive and non-positive locking) * 4 cloverleaf lashing points on each side * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminum approach ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment at the rear) ----Information: * Load securing certificate in accordance with DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Gross vehicle weight of 20,000 kg technically possible * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering system, including RtR valve and manual lowering for loading operations ----Drawbar / Flange Eye: * Drawbar with positive-locking height adjustment * 50 mm flange eye ----Electrics / Lighting: * 15-pin 24 V system * LED tail lights 12 / 24 V integrated into underrun protection ----General Attachments: * Support winch at front * Externally mounted folding supports at rear * Plastic toolbox, approx. 750 x 350 x 300 mm, mounted on the right side * Plastic quarter mudguards ----Tipping Platform: * Steel pallet three-way tipper body made from fine-grain steel with high-strength M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall made from smooth sheet metal * Hardwood pad for excavator bucket, bolted to front wall * Continuous side walls – without center stakes – folding, with drop-side spring lift and swing function via manual central locking * Rear stakes bolted * Combined steel double-leaf tailgate, asymmetrically split, swiveling up to 270° and lockable (not foldable), with additional swing frame for automatic tailgate opening during tipping, lockable by galvanized rotary latch and central locking, deactivation function for automatic tailgate release when tipping backward with open door * 4 mm steel floor * Two-step entry on front left * Rear guide rail for loading ramps ----Load Securing: * One 7-ton lashing ring in each corner Dodjvin Ucepfx Adqour * Four 3-ton lashing eyes per side, recessed into outer frame ----Loading Ramps: * Rear loading ramp recess integrated into chassis * One pair of aluminum loading ramps (10 tons/pair), approx. 3570 x 410 mm, suitable for rubber-tired and tracked vehicles ----Coating / Finish: * Chassis, drawbar, rear stakes, front wall, tipper bed, underrun protection, rear folding supports hot-dip galvanized * Side walls cataphoretic dip-coated (KTL) and tailgate painted RAL 9010 pure white * Custom RAL color for side walls available at extra cost * Axles, air tanks, flange eye, and front support winch painted in black ----Info: * Load securing certificate according to EN 12642 XL? * Errors and prior sale excepted * Sample images (vehicle photos may differ due to optional equipment) ----Delivery Time: * Available from calendar week 15 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2025, * TRA-Kombi 18.0: * 3-in-1 – Suitable for hooklift containers, skip loaders, and use as a low-loader ----Braking System: * RDÜ tire pressure monitoring system * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinder ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm drawbar eye with height adjustment ----Electrics / Lighting: * LED tail lights * 15-pin power connector * RDÜ (tire pressure monitoring), in-cab display via EBS signal (no truck-side installation required) ----General Attachments: * Tool box made of powder-coated sheet steel, mounted on the right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box for container nets, made of galvanized sheet metal, approx. 960 x 300 x 400 / 450 mm, right side Dujdpfx Adel Thv Reqsr * Plastic rear impact bumpers * Mechanical drop-down support legs at the rear ----Loading Platform: * Hot-dip galvanized main frame with raised outer rails (approx. 25 mm higher) for guiding roll containers * Steel floor plate with roller recesses in the bogie area * For hooklift container transport, container lengths from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking and mechanical plug-in stops at the front in the running track; load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * 8 repositionable container stops for lateral centering, front 4 stops plug-in with pivoting stop * Continuous weld bead as anti-slip coating on the ramp running area ----Load Security: * 3 pairs of 10 t UVV lashing rings mounted sideways for securing containers with positive locking and frictional connection * 4 cloverleaf-shaped lashing points on each side * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminum approach ramps (10.6 t per pair), 2,800 x 470 mm, suitable for vehicles with rubber tires and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * Permissible gross vehicle weight technically possible up to 20,000 kg * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without truck-side installation * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors for total axle load display per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Straight rear steel mudflaps, each with spray suppression * Side underrun protection * Superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable folding lids (folding lids opening to the rear) * Chassis made from high-strength fine-grained steel * Floor over the bogie platform made of 50 mm softwood, and 60 mm softwood in the low loader platform * Outer planks of the drive-on ramps made of 50 mm hardwood Duodpfxjxmpydo Adqsr * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, 1 pair each of 13.4 t lashing rings at the front and rear outer frame, 1 pair each of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front recess, 1 at the rear), 2 pairs of 6.4 t lashing rings on the excavator stick holder * 11 pairs of folding outriggers for a total width of 3 meters (not at the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening boards made of sheet steel, mounted transversely to the loading area in front of the first rear axle * Excavator stick holder above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area over the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop-down supports, and drive-on ramps galvanised * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is galvanised * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle self-steering (lockable from the driver's cab for maneuvering purposes without the need for truck-side installation; additionally lockable via switch on trailer). Deactivate the lock before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required), with speed-dependent control via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar, 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with indication in the truck via EBS signal (no truck-side installation necessary) * LED lighting system 12/24 V * Removable rear LED beacon ----General Accessories: * Mechanical warning plate kit for 3 m total width * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted side left * Front axle with plastic mudguards, rear with galvanized steel mudguard skirts ----Low Loader Platform: * Front section of turntable platform with 45° angles and 3 storage compartments with lockable, rear-hinged covers * Shortening of the lowbed platform by 500 mm to 6,280 mm including extended step by 500 mm to the front * Rubber covering on folding frame, drive-on ramp and running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator arm rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at front corners * 2 x 13.4 t UVV lashing points each at side front and rear corners * 5 x 10 t UVV lashing rings per side (pivoting and lowerable, loadable in all directions) * 4 stake pockets per side with additional 2 t lashing capability each * 1 x 16 t UVV lashing ring on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m total width (beam holders under chassis, right side) ----Excavator Arm Rest: * Continuous excavator arm rest with reinforcement profile from last axle to tow bar approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on sides of arm rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and extendable tip piece approx. 4,650 x 720 mm including load-holding valves and hydraulic side shift ----Rear Support: Duodpfol Tihujx Adqjr * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (required in case of hydraulic pump output on truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Lowbed platform: 6,280 + 500 x 2,520 mm incl. 860 mm inclines ----Paintwork: * Chassis, turntable, drawbar, widening consoles, and ramps hot-dip galvanized * Tow bar, axles, hydraulic axle supports, and air tanks painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately*

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: Dsdpfxjxptn Do Adqeur * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: novo, največja dovoljena obremenitev: 30.080 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear Dusdpfjxmpykox Adqer * Warning sign packages front & rear * SmartBord infotool installed with pressure sensors for displaying axle group loads * Reflective contour tape on the sides and rear * LED beacon (removable) at the rear * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front enclosed individual plastic mudguards * Rear straight steel mudflaps with spray suppression * Side underrun protection * Extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments with lockable folding lids (folding lids open towards the rear) * Chassis made from high-strength fine-grain steel * Floor over bogie platform made of 50 mm softwood, and in the low-bed platform made of 60 mm softwood * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t each at the front left and right on the main frame of the bogie platform; one pair of 13.4 t lashing rings at the front and rear sides of outer frame; one pair of 10 t lashing rings on each side foldable and lowerable, loadable in all directions, integrated into the side frame; 5 t bolted lashing rings on the outer frame of the wheel recesses (2 per front wheel recess, 1 per rear); 2 pairs of 6.4 t lashing rings at the excavator stick compartment * 11 pairs of fold-out outriggers for overall width of 3 m (not on the rear incline) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for width-extension planks, steel, mounted crosswise to the loading area in front of the first rear axle * Excavator stick compartment above the rear axle extending to the end of the ramp incline, approx. 2,300 x 740 x 190 mm * Two wheel recesses per side approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on bogie platform) for transporting wheel loaders with wheelbase 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulic extendable tip, approx. 4,650 x 720 mm * Hydraulic sideward ramp displacement * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded deck height approx. 890 mm ± 20 mm (including 860 mm ramp incline) * Chassis, bogie, fold-out outriggers, rear supports, and access ramps fully hot-dip galvanized * Axles, air tanks, and drawbar painted in black shade * Tires: 235/75R17.5 * Vehicle is fully hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.600 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 700 mm, Leto izdelave: 2026, * KA-TA-RT 18.0: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with lifting and lowering system, including RtR valve and manual lowering function for loading operations ----Drawbar / Flange Towing Eye: * Drawbar with positive-locking height adjustment * 50 mm flange towing eye ----Electrics / Lighting: * 15-pin 24 V electrical system * LED tail lights 12 / 24 V integrated in underrun protection ----General Fitted Components: * Landing gear at front * External folding supports at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on right side * Plastic quarter mudguards ----Tipper Body: * Steel pallet 3-way tipper body made of high-strength fine-grained steel with high M-Strong side walls and reinforced 180 bar tipping cylinder * Fixed front wall made of smooth sheet metal * Hardwood pad for excavator bucket bolted to the front wall * Continuous side walls – without central stanchion – folding with board spring lifters and manual central locking with swinging function * Screwed-in rear posts * Combination steel double-wing tailgate, asymmetrically split, swivels and locks up to 270°, not foldable, with additional swing frame for automatic tailgate opening during tipping; locking via galvanized rod latch and central locking, deactivation function for automatic tailgate opening when tipping backwards with open wing door * 4 mm steel-sheet floor * Two-step entry, front left * Rear track rail for loading ramps ----Load Securing: * 1 x 7 t lashing ring in each corner Dusdpovin T Sjfx Adqjr * 4 x 3 t lashing eyes recessed in the side external frame ----Loading Ramps: * Recessed compartment for loading ramps at rear in the chassis * 1 pair of aluminium loading ramps (10 t / pair) approx. 3,570 x 410 mm, suitable for rubber-tyred and tracked vehicles ----Paintwork: * Chassis, drawbar, rear posts, front wall, tipper body, underrun guard, rear folding supports hot-dip galvanized * Side walls – KTL-coated – and tailgate painted in RAL 9010 pure white * Side walls in other RAL colours available at extra cost * Axles, air tanks, flange towing eye, front landing gear painted in black tone ----Information: * Load securing certificate according to EN 12642 XL? * Errors and prior sale excepted * Sample images (actual vehicle photos may vary due to special equipment) ----Delivery time: * Available from calendar week 15 / 2026

Stanje: rabljeno, lastna masa: 3.210 kg, največja dovoljena obremenitev: 8.690 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 05/2021, naslednji pregled (TÜV): 06/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.430 mm, višina nakladalnega prostora: 500 mm, vzmetenje: jeklo, velikost pnevmatike: 235/75 R17.5, Leto izdelave: 2021, Oprema: ABS, Nemško vozilo MASTERLINE Duedpsyw N Npjfx Adqsr Müller-Mitteltal KA-TA-R 11,9 trosmerni kiper sa rampama ispod utovarene Godina prve registracije: 05/2021 pocinkovan Dozvoljena ukupna masa: 11.900 kg Sopstvena masa: 3.210 kg Nosivost: 8.690 kg Dimenzije pneumatika: 235/75 R 17,5 Tandem osovina manja od 1 m Vučna ruda je neprekidno podesiva po visini, toplo pocinkovana, vučna kuka 40 mm Ram pocinkovan BPW osovine Visina poda: 0,93 m Dodatne usluge dostupne! Izvozne tablice (crvene / 30 dana) Nemačka Kratkoročne tablice (žute / 5 dana) Nemačka Moguća organizacija austrijskih prevoznih tablica Isporuka vozila (uz nadoknadu) Podaci dati na internetu su nezahtevne informacije. Ne predstavljaju zagarantovana svojstva. Prodavac ne preuzima odgovornost za greške, tipografske greške i greške u prenosu podataka. Prodaja uz mogućnost prethodne prodaje. Prodaja isključivo privrednim subjektima. Važe isključivo naši Opšti uslovi poslovanja.

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, barva: črn, Leto izdelave: 2005, Oprema: ABS, = Further options and accessories = - Spare wheel - Twin tyres = Remarks = Müller Mitteltal 2-axle T5 2AL low-loader with ramps Air suspension BPW axles ABS ZSA Tyres 60% GR 235R17.5 ID No. 665 We look forward to welcoming you for consultation, contract signing or vehicle collection at our dealership. Please arrange an appointment in advance. If you are unable to visit us in person, we offer complete processing via phone/email/WhatsApp/fax. Upon request, we can deliver your new vehicle directly to your door. This means the best price, maximum security and convenience when purchasing your vehicle. Trade-in We are happy to accept your used car as a trade-in. We offer a digital vehicle appraisal based on your vehicle photos, even without a dealership visit. Our specialised purchasing team guarantees you the highest possible price. Upon request, we will deliver your new 'pre-owned' vehicle nationwide directly to your door and take back your used car. Dsdpfx Asxw T Uajdqsur Financing - Leasing Immediate approval and takeover of existing loans. Your specialist partner for passenger cars, vans, commercial vehicles and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial estate) Visit our website at Over 400 vehicles in stock at all times The information provided in advertisements, on the internet, price tags and images is non-binding and does not constitute warranted characteristics. The seller assumes no liability or guarantee for typing errors or data transmission mistakes. Listed equipment should be verified separately if necessary. The offer is generally without new general inspection (TÜV); we would be happy to quote for inspection via our partner workshop. Subject to error and prior sale. = Further information = Unladen weight: 8,900 kg Payload: 26,100 kg Gross vehicle weight: 35,000 kg Sales price: €18,000, US$20,770

Stanje: rabljeno, prva registracija: 06/2011, skupna širina: 25.500 mm,

Stanje: rabljeno, konfiguracija osi: 1 os, prva registracija: 08/1993, Leto izdelave: 1993, Oprema: ABS, = Further Options and Equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal KA-TA Tipping Trailer Single axle Air suspension ABS Tyres 60% Processing We look forward to welcoming you for a consultation, contract signing, or vehicle collection at our dealership. Please schedule an appointment. If you are unable to visit us in person, we offer complete processing via phone, e-mail, WhatsApp, or fax. On request, we can deliver your new vehicle directly to your door. This means you benefit from the best price, maximum security, and convenience during your transaction. We are also happy to take your used vehicle in part exchange. We offer a digital vehicle appraisal based on your photos, even without you visiting our dealership. Our dedicated purchasing team guarantees you the highest price. Upon request, we can deliver your new 'used' vehicle nationwide, directly to your doorstep, and collect your trade-in vehicle. Financing - Leasing Immediate approval and old loan settlement Duedpfxjxt Sl Ns Adqjr Your specialist partner for passenger cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (Industrial estate) Over 400 vehicles in stock at all times The information provided in advertisements, on the internet, on price tags and in images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability or warranty for typographical and data transmission errors. Listed equipment should be checked separately if necessary. The offer is generally without a new MOT; we are happy to provide a quote for an inspection at our partner workshop. Subject to errors and prior sale. = Further Information = Unladen weight: 3,700 kg Payload: 9,300 kg gross vehicle weight: 13,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 03/2004, Leto izdelave: 2004, Oprema: ABS, = Additional options and equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal RAK German vehicle Roll-off trailer 2-axle Air suspension ABS Tyres 60% ID no. 709 We look forward to advising you, signing contracts, or handing over the vehicle at our dealership. Please make an appointment. If you are unable to visit our showroom, we offer complete processing by phone, email, WhatsApp, or fax. On request, we deliver your new vehicle directly to your door. This means you get the best price as well as maximum safety and convenience with your purchase. We are happy to take your used vehicle as a trade-in. We offer you the option of a digital vehicle appraisal based on your vehicle photos, even without visiting the dealership. Our specialised purchasing team offers you a guaranteed top price. Upon request, we deliver your new ‘used’ vehicle nationwide directly to your doorstep and take your trade-in back with us. Dedpfx Asxyx Haodqeur Financing – leasing Immediate approval and settlement of existing loans. Your specialist partner for passenger cars, vans, commercial vehicles, and construction machinery. ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (industrial area) Over 400 vehicles in stock at all times. The information given in advertisements, on the internet, on price labels, and in pictures are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately by the buyer. Offer is generally without new TÜV approval; we will gladly provide you with an offer from our partner workshop. Subject to errors and prior sale. = Further information = Unladen weight: 4,850 kg Payload: 13,150 kg Gross vehicle weight: 18,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 04/2005, Leto izdelave: 2005, Oprema: ABS, = Further Options and Equipment = - Electronic Braking System (EBS) = Notes = Müller-Mitteltal KA-TA 18 We look forward to advising you. Contract signing or vehicle collection takes place at our dealership. Please arrange an appointment. If you are unable to visit us in person, we can handle the entire process via telephone, email, WhatsApp, or fax. On request, we can deliver your new vehicle directly to your doorstep. This ensures you get the best price, maximum security, and convenience when taking delivery. We are happy to take your used vehicle in part exchange. We also offer digital vehicle appraisal based on your photos, without requiring a visit to our dealership. Our specialized purchasing team guarantees you the highest possible price. If you wish, we can deliver your new used vehicle nationwide right to your door and collect your trade-in at the same time. Financing and leasing available — immediate approval and settlement of your existing loan. Your expert partner for passenger cars, transporters, commercial vehicles, and construction machinery: ITC GmbH & Co. KG Siemensstraße 7 32312 Lübbecke (industrial area) Always over 400 vehicles in stock. All details in advertisements, online listings, price tags, and pictures are non-binding descriptions and do not constitute guaranteed features. The seller assumes no liability or warranty for typographical or data transmission errors. Listed equipment must be individually verified where applicable. This offer does not include a new TÜV inspection; we are happy to provide an offer for a TÜV inspection through our partner workshop. Subject to error and prior sale. Information available in German. = Further Information = Duedpfx Asxt Tf Rsdqsr Unladen weight: 4,080 kg Payload: 13,920 kg Gross vehicle weight: 18,000 kg

Stanje: rabljeno, konfiguracija osi: 2 osi, prva registracija: 08/1996, Leto izdelave: 1996, Oprema: ABS, = Additional Options and Equipment = Dsdpoxt Sd Eofx Adqjur - Electronic Braking System (EBS) = Remarks = Müller-Mitteltal Trailer ATL Roll-off trailer 2-axle Air suspension ABS Tyres 60% Information available in German We look forward to advising you Contract signing or vehicle collection at our dealership. Please arrange an appointment If you are unable to visit our dealership in person, we offer complete processing via telephone/email/WhatsApp/fax On request, we can deliver your new vehicle directly to your door This means best price for you, maximum security and convenience during acceptance We are happy to accept your used vehicle as part-exchange We offer the option of digital vehicle evaluation based on your vehicle photos even without a dealership visit Our specialised purchasing team offers you a guaranteed top price On request, we deliver your new used vehicle nationwide directly to your door, and collect your trade-in for financing or leasing Immediate approval and settlement of existing credit Your specialist partner for cars, transporters, commercial vehicles, and construction machinery ITC GmbH & Co KG Siemensstraße 7 32312 Lübbecke (Industrial Area) Over 400 vehicles permanently in stock The details provided in advertisements, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability/warranty for typing or data transmission errors. Listed equipment may need to be checked separately. Our offer generally does not include new TÜV approval; we are happy to make you a quote with our partner workshop. Subject to errors and prior sale = Additional Information = Unladen weight: 2,360 kg Payload: 10,640 kg Gross vehicle weight: 13,000 kg

Stanje: rabljeno, največja dovoljena obremenitev: 15.100 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 03/1987, dolžina tovornega prostora: 8.650 mm, širina tovornega prostora: 2.480 mm, ? Mehanske rampe ? Nakladalna višina: cca 910 mm ? Nosilec rezervnega kolesa ? Vlečno uho 40 mm ? Rotacijska luč ? Bobnasta zavora ? Listnato vzmetenje ? 1 x shranjevalna skrinja ? Dvojna kolesa ? SAF osi Vsi podatki brez garancije / Predhodna prodaja pridržana. Djdoyw Egwepfx Adqour

Stanje: rabljeno, največja dovoljena obremenitev: 29.850 kg, skupna masa: 32.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2012, naslednji pregled (TÜV): 04/2028, Leto izdelave: 2012, Interna številka vozila: G300402 Nemško vozilo Takoj na voljo na našem dvorišču v Kaufungen - Kassel, Nemčija Več INFO pri Luis Lucena Letnik 2012 Lastna masa priklopnika: 6.530 kg Priklopnik mešalec betona LIEBHERR 10 m³ Možne so napake. Dujdpsxy Ul Ssfx Adqor Z veseljem vzamemo vaše rabljeno vozilo v račun. Financiranje možno neposredno pri nas. GOLEC NUTZFAHRZEUGE GMBH Govorimo: nemško, angleško, špansko, poljsko, ukrajinsko, rusko, bolgarsko.