Müller-Mitteltal 11,9 To Tandemkippanh. Mit Anlegerampen nakup rabljenega (36.137)

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Brakes: * Wabco EBS-E braking system * Emergency release system for spring-loaded cylinders * Drum brakes * Duomatic brake connection ----Axles: * 2 x ton SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with ride height +30 mm via positioning cylinder * Starting aid for shunting and mandatory lowering on the first axle – controlled via speed-dependent EBS electronics (no installation required on the truck; also with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via radio remote control ----Drawbar / Flange Drawbar Eye: * 50 mm flange-mounted drawbar eye, height-adjustable by +77 mm and -33 mm, for 2 t support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V Nedpfx Abox Dp Ats Hjlc * 2 LED reversing lights, switched via reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * Extended connecting cables for agricultural and forestry vehicles * Power supply for radio remote: 12+24 V via taillight ----General Attachments: * BPW landing leg at the front * Mechanically extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-finish aluminium wheels * Split-pin towing coupling (use only with retracted underrun protection) * Enclosed plastic half-shell single mudguards * Two-step access before the front bulkhead on the left side * Shovel and broom holders in front of the front bulkhead * 2 matte stainless steel toolboxes, approx. 650 x 350 x 320 mm, mounted right side * Enclosed side protection usable as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine end from truck/tractor), rated for 180 bar (tractor operation) * Double-acting control circuit for hydraulic tailgate (mounted front right), operated via radio remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hook system (Serial no. 100746129, year 2023) * Base frame made of high-strength fine-grained steel * 20,000 kg pulling force * Hook height 1,570 mm * Control of hooklift via radio remote control * Remote control with rapid function when lowering, not when raising * Emergency stop switches left and right sides * Container supports with 4 lateral supports per side and one roller at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist in lifting the main arm * 2 x mechanical fall supports at the rear * Approval for 20 t gross vehicle weight (2 x 9 t axles) and 2 t support load * Note: If the radio remote is outside the charging cradle, the service brake must be applied for radio release. Brake connections must remain connected at all times so the hydraulically/pneumatically operated valves can be opened. * Monitoring system for underrun protection to ensure it is retracted when tipping ----Loading Height: * Unladen approx. 1,300 mm with lowered lift axle ----Paintwork: * Chassis, drawbar, access steps, underrun protection, and fall supports hot-dip galvanized * Axles, air tanks, front landing gear painted black * Palfinger hooklift painted black/yellow ----Information: * Errors and prior sale reserved * Vehicle is in very good / as-new condition ----Delivery time: * Vehicle is immediately available

Stanje: novo, največja dovoljena obremenitev: 13.830 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Leto izdelave: 2026, * KA-TA-R 18 ----Brakes: * EBS-E (electronic braking system with RSS) * Emergency release for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 9 t Gigant axles ----Suspension: * Air suspension with level control during tipping ----Electrics / Lighting: * Tire pressure monitoring system with display possibility in the truck dashboard via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting with galvanized protective cover * 2 LED reversing lights ----Drawbar eye / Drawbar: * Drawbar with 50 mm flange towing eye (adjustable by +77 mm and -33 mm using offset plate) ----General attachments: * Landing leg at the front * Foldable galvanized steel underrun guard for paver feeding * Enclosed single plastic mudguards * Front wall platform made of grating with step on drawbar and handholds on the front wall ----Chassis: * Chassis made of fine-grain steel ----Tipper body: * Steel 3-way tipper body with continuous asymmetrical aluminum side walls – without center stanchion – pendulum-mounted with manual central locking, left side foldable with side board spring lifter * Tailgate – made from HBW 400 steel – pendulum-mounted with automatic 2-claw lock * 5 mm steel floor made from HBW 450 steel ----Load securing: Nodpfx Aex Ipbyjb Hjlc * 4 x 3 t lashing rings per side – recessed and foldable – integrated into the steel floor ----Roll tarp: * Roll tarp – agate grey, similar to RAL 7038 * Tarpaulin tensioning using ratchet tensioners on the sides and tensioning rubber at the front and rear ----Painting: * Chassis, underrun guard, and drawbar hot-dip galvanized * Axles, air tanks, landing leg, and flange towing eye painted in a shade of black * Side wall painting according to RAL color of choice (excluding special or metallic paints); color can be changed up to approx. 6 weeks before completion ----Info: * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale * Sample images (vehicle images may vary due to special equipment) ----Delivery time: * Vehicle available from week 42/2026

Stanje: rabljeno, največja dovoljena obremenitev: 12.080 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, prva registracija: 06/2024, dolžina tovornega prostora: 3.900 mm, širina tovornega prostora: 1.920 mm, višina nakladalnega prostora: 415 mm, Leto izdelave: 2022, Oprema: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange towing eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on towing eye ----General attachments: * Jost landing gear at the front * Side underrun protection * Foldable A-panel at the rear ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Superstructure: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding plate cover 750 x 1,000 mm at the front incl. 2 removable skip stops, front in 2 positions * Rear cross member for attaching aluminium ramps, incl. 2 additional drop-down supports at the rear ----Loading edge: * Unloaded loading edge approx. 710 mm ----Load securing: * 4 removable skip stops, can be inserted into 2 positions for lateral centring of the skips * On each side: 1 x (13.5 t) UVV lashing point for attaching tensioning devices * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick-shortener (tensioning force 6,300 kg) Nledpfxjl Th Eyj Ab Hec ----Tyres: * Tyres: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop supports hot-dip galvanized * The axles, springs, landing gear, and air tank painted in a black tone ----General information: * Vehicle has a one-day registration in 06/2024, due to missing tyre pressure monitoring system it has not been loaded/used * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 14.650 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, Leto izdelave: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic brake system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Disc brakes * Duomatic brake coupling * 2 x 10 t SAF axles * Air suspension with automatic lowering when uncoupling the brake * Drawbar 2,300 mm long with 40 mm towing eye and height adjustment via tension spring & spindle * Plastic toolbox on the right side, closed plastic mudguards * Side impact protection closed on one side, suitable as an advertising surface * Rear underrun protection with 2 buffer stops * Foldable "A"-sign at the rear for waste disposal * LED tail lights with protective housing * 2 x 7-pin power connectors * Chassis hot-dip galvanized (excluding air tanks, axles, drawbar, etc.) * Roller track length approx. 6,950 mm * Roll-off container secured with pneumatic 4-point claw locking system * At the front: 2 plug-in container stops with 2 additional plug-in positions * Unladen ride height approx. 1,165 mm * -- Permissible gross weight of 20,000 kg technically possible -- * Suitable for 5,000 – 7,000 mm container lengths * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf Nedpfx Absl Tpy Hj Helc

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: Nlsdpfxstplv To Ab Hoc * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Lifting middle axle ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumpers * Mechanical rear drop-down supports ----Container / Low-bed Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length of 5,500 - 7,000 mm possible * Pneumatic 4-point container clamp locking as well as mechanically plug-in front stop angles in the guide tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering of the skips, front 4 skip stops plug-in with pendulum stoppers ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and non-positive load securing of skips * 4 lashing rails in cloverleaf design (side) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp incline running area * 1 pair of aluminum approach ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without initial registration with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: rabljeno, največja dovoljena obremenitev: 14.300 kg, skupna masa: 20.000 kg, konfiguracija osi: 2 osi, prva registracija: 07/2023, naslednji pregled (TÜV): 11/2026, Leto izdelave: 2023, * HL - TA 20.0 ----Braking System: * Wabco EBS-E braking system * Emergency release device for spring brake cylinders * Drum brakes * Duomatic brake connection ----Axle: * 2 x ton SAF axles * 1st axle as lift axle (fully automatic) * Lift axle with driving height +30 mm via positioning cylinder * Traction aid for shunting purposes and forced lowering onto the first axle – controlled via speed-dependent EBS electronics (no installation required on truck side, additionally supplied with cable for operation from the tractor) ----Air Suspension: * Air suspension with lowering function via radio remote control ----Drawbar / Flange Eye: * 50 mm flange screw drawbar eye – height adjustable by +77 mm and -33 mm – for 2 ton support load ----Electrics / Lighting: * 15-pin power connector * 3-pin 12V auxiliary connector * LED lighting system 12 / 24V * 2 LED reversing lamps activated by reverse gear * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * Extended connection cables for agricultural and forestry vehicles * Power supply for radio control 12+24V via tail light ----General Attachments: * BPW landing gear at the front * Mechanical, extendable underrun protection for container lengths over 6,000 mm * Speedline diamond-cut aluminium wheels * Pin-type towing coupling (use only when underrun protection is retracted) * Closed plastic half-shell individual mudguards * Two-step access in front of the front bulkhead on the left * Shovel and broom holder in front of the front bulkhead * 2 matt stainless steel toolboxes, approx. 650 x 350 x 320 mm, right side mounted * Closed side underrun protection can be used as advertising space ----Hydraulics: * 2-circuit hydraulic connections (engine-side from truck/tractor) designed for 180 bar (tractor operation) * Double-acting control circuit for hydraulic rear door (mounted front right) operated via remote control ----Hooklift: * Palfinger PHT 20 SCASNSLD5 telescopic hooklift device (serial no. 100746129, year 2023) * Base frame made of high-strength fine-grain steel * 20,000 kg tractive force * Hook height 1,570 mm * Hooklift operated via radio remote control * Radio remote control with fast function during tipping, but not during winching * Emergency stop switches on both left and right sides * Container bed with 4 side supports each and one roll at the rear * Hydraulic rear internal locking * 2 additional hydraulic cylinders to assist with raising the main arm * 2 x mechanical folding rear supports * Approval for 20 ton gross weight (2 x 9 ton axles) and 2 ton support load * Note: If the radio control is outside the charging cradle, the service brake must be engaged to enable remote operation. Brake connections must remain connected at all times to operate the hydraulic/pneumatic control valves. * Monitoring system for underrun protection to ensure it is retracted while tipping ----Loading Height: * Unladen approx. 1,300 mm with lift axle lowered ----Paintwork: * Chassis, drawbar, access steps, underrun guard, and folding supports hot-dip galvanized * Axles, air tanks, and front landing gear painted in black * Palfinger hooklift painted in black/yellow ----Information: * Subject to errors and prior sale * Vehicle in very good / like-new condition Nodpfox Dp Agjx Ab Helc ----Delivery Time: * Vehicle immediately available

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * KA-TA-R 14.4 ----Braking system: * Wabco EBS * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Towing Eye: * Height-adjustable (approx. 300 mm), hot-dip galvanized drawbar with 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding supports at the rear * Hot-dip galvanized bolted underrun protection * Toolbox made of galvanized steel sheet, mounted on the right side * Plastic quarter mudguards * Two-step entry on the left side as access aid ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * LED tail lights ----Tipper Platform: * Steel pallet three-way tipping body * Continuous side walls at the top with internal tube reinforcement (without central stanchions), foldable using drop side spring lifters * Rear wall foldable and pendulum-mounted, with manual central locking * Hot-dip galvanized, bolted rear stanchions * 4 mm fine-grain steel floor plate * Mesh hooks, rear mounting rail for drive-on ramps * Prepared for later retrofitting with side wall extensions ----Chassis: * Hot-dip galvanized chassis ----Load Securing: * Each corner with 1 x 5 t lashing ring and each side with 4 x 3 t lashing rings embedded in the outer frame ----Aluminum Drive-on Ramps: * 1 pair of aluminum drive-on ramps approx. 3,570 x 400 mm (load capacity 8 t/pair) suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading platform integrated in the chassis, accessible from the rear ----Tires: Nodsl Th A Eopfx Ab Helc * 385/55 R 22.5 tires ----Painting / Coating: * Axles, springs, air tanks, and landing gear painted in black * Chassis, drawbar, floor, front wall, and folding supports hot-dip galvanized * Sidewall finish in RAL 9010 pure white * Side wall painting in other RAL colors available at extra cost ----Info: * Reinforced superstructure with load securing certificate according to EN 12642 XL * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 29/2026

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: ----Braking System: * Electronic Braking System (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Towing Eye: * Drawbar height-adjustable by 300 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS (tire pressure monitoring system with indicator function in the truck via EBS signal—no installation required on the truck side) * LED lighting system * 15-pin electrical connector ----General Accessories: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted front right on the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floorboards * Preparation for subsequent installation of 20" container locks at front and rear * Bolted, smooth sheet metal front wall * Side walls made of trapezoidal-profiled steel, foldable with drop-side spring assist * Hot-dip galvanized bolt-on rear stanchions ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing points every 480 mm * Option for 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in front and end crossmembers for 1.2 t securing points ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles, stored in a compartment underneath the loading area in the chassis, accessible from the rear ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, front wall, and rear wall * Entire vehicle hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: Njdpfxendpn Se Ab Helc * Immediately available ex works Egestorf

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: Nsdpfxspk D Iis Ab Helc ----Braking System: * Wabco EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axles: * 3 x 11 t Gigant axles * Center axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Tool box made of powder-coated sheet steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized sheet steel (W: 960 mm x H: 300 x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with splash guards * Plastic rear impact protection buffer * Mechanical rear support legs ----Container / Low Loader Deck: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll containers * Steel sheet floor with roller recesses in the bogie area * Suitable for roll-off container transport with container lengths from 5,500 to 7,000 mm * Pneumatic 4-point container clamp lock and mechanical plug-in end stops at the front of the tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Includes 8 repositionable skip stops for lateral centering, front 4 skip stops plugged in with swinging end stop ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 cloverleaf-style lashing bars on each side and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp run-up area * 1 pair of aluminum loading ramps (16 t/pair) 2,800 x 400 mm suitable for rubber-tyred and tracked vehicles (lockable storage compartment at the rear) ----Tires: * Tires: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on the sides & rear * Axles, turntable, drawbar, and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible total weight technically possible: 27,000 kg * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 10.800 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with equalizing unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with in-cab display via EBS signal—no in-cab installation required * 15-pin power connector * LED lighting system, 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * External folding rear support legs * Plastic toolbox approx. 858 x 500 x 500 mm, front right, mounted externally on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Provision in front of the bulkhead for retrofitting container locks * Bolted 400 mm smooth steel bulkhead * Bolted rear stanchions * Side walls with spring assist ----Load Securing: * Perforated outer frame, angled at approx. 45°, with 2 t lashing capacity every 480 mm * Option to install 3 t drop lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross member for 1.2 t lashing points * Profifix lashing rail along the centerline for lashing capabilities up to LC 3000 daN ----Ramps: * One-piece hydraulic grating ramps, approx. 2,750 x 600 mm (can be compacted to 20 mm) Nsdpfxjrwc R Ae Ab Hjlc * Hydraulic flow divider in the trailer (for hydraulic pump performance in the truck of over 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical drop supports, and ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange towing eye painted in a black shade * Side wall paintwork in RAL 9010 pure white * Painting of the side walls in an RAL color of choice available at an extra charge ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Sample images shown ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem compensation unit ----Drawbar / Flange Towing Eye: * Drawbar height-adjustable by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power plug * LED tail lights 12/24 V * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required ----General Attachments: * Jost mechanical landing gear at front * 2 mechanical foldable support legs at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted at the front right side of the chassis * Bolted underride guard * Plastic quarter mudguards ----Tipping Platform: * Mesh hooks positioned at the central locking mountings and 2 at the front bulkhead * Steel pallet - 3-way tipper body with reinforced Strong sidewalls (continuous upper sidewalls with internal tube reinforcement – without central stanchions – foldable with sidewall spring lifting device) * Screw-fixed rear stanchions * Combination steel wing doors at rear, 2-leaf, asymmetrically split, can be swung and locked up to 270° (not foldable), with additional swinging frame for automatic tailgate opening during tipping; locking by galvanized rod lock at rear and central lock; deactivation function for automatic tailgate opening during rear tipping with opened wing door * 4 mm fine-grained steel floor plate ----Load Securing: * 1 x 5 t lashing point in each corner * 4 x 3 t lashing rings recessed in the outer frame on each side ----Chassis: * Chassis made of fine-grained steel ----Ramps: * Rear mounting track for deployable ramps * 1 pair of aluminium ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment for ramps integrated below the loading area in the chassis at the rear ----Tyres: * Tyre size 358/55 R 19.5 Nodpfx Abox Hm Rcs Holc ----Painting: * Drawbar, underride guard, rear stanchion, and rear foldable support legs hot-dip galvanized * Axles, springs, air tank, and landing gear painted in black shade * Sidewalls painted in RAL colour of choice (no special or metallic paint) – can be modified up to approx. 6 weeks before completion ----Other Information: * Reinforced body with load securing certificate * Errors and prior sale excepted * Sample images ----Delivery Time: * Immediately available from calendar week 29/2026

Stanje: novo, največja dovoljena obremenitev: 10.660 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 600 mm, Leto izdelave: 2026, * KA-TA-R 14.4: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, adjustable by 300 mm, with 40 mm flange drawbar eye ----Electrics / Lighting: * 15-pin power connector * LED rear lights 12/24 V * Tire pressure monitoring system with in-cab display via EBS signal – no truck-side installation required ----General Attachments: * Jost mechanical landing leg at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted right front of the chassis * Bolted underrun protection Njdex Hm Riepfx Ab Holc * Plastic quarter mudguards ----Tipper Body: * Net hooks mounted at the positions of the central locking as well as 2 pieces on the front wall * Steel pallet 3-way tipper body with reinforced strong side walls (continuous side walls with internal tube reinforcement – without intermediate stakes – drop-down with board wall spring lifter) * Rear uprights bolted * Combination steel swing doors at the rear, two-leaf, asymmetrically split, pivotable and lockable at 270° – not drop-down – with additional pendulum frame for automatic rear wall opening during tipping, locking via galvanized rotary latch at the rear and central locking. Deactivation function for automatic rear wall opening when tipping backwards with open swing door * 4 mm fine-grain steel floor plate ----Load Securing: * 1 x 5 t lashing point in each corner * 4 x 3 t lashing rings each side, integrated into the outer frame ----Chassis: * Chassis made from fine-grain steel ----Ramps: * Rear ramp rails for drive-on ramps * 1 pair of aluminium drive-on ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tyred and tracked vehicles * Lockable storage compartment for the ramps integrated into the chassis under the loading bed, accessible from the rear ----Tyres: * Tyres 358/55 R 19.5 ----Paintwork: * Drawbar, underrun protection, rear upright, and rear folding supports hot-dip galvanized * Axles, springs, air reservoir, and landing leg painted in black tone * Side walls painted in a RAL colour of your choice (no special or metallic paint) – can be changed up to about 6 weeks before completion ----Information: * Reinforced body with load securing certificate * Errors and prior sale excepted * Sample images ----Delivery time: * Available immediately from CW 29/2026

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ - TA -R 14.4 ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Drawbar Eye: * Drawbar adjustable in height by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flanged drawbar eye Nlodpex Ipapefx Ab Hec ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * 15-pin power connector * LED tail lights 12 / 24 V * LED rotating beacon (removable) at rear ----General Attachments: * Support winch in front * Externally mounted hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right, outside at the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * Preparation in front of front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Sidewalls made of trapezoidal profile steel sheet, foldable with drop-side spring-assisted lifting device * Steel rear wall can be slid between the ramps – storage bracket for unused rear wall inside by the front wall * Rear stanchions bolted * Rear approach angle approx. 860 mm ----Flooring: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of ramps * 12 mm thick and 210 mm wide rubber strips on the approach slope and externally on the low-bed platform (from front wall to end sill) ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing rings every 600 mm possible * 1 x 6.3 t lashing ring at each front and rear corner * Various drill holes in front wall and end sill for 1.2 t lashing options ----Ramps: * One-piece mech. grating ramps with spring system for one-man operation, approx. 2,750 x 870 mm (can be compressed to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tank, and flanged drawbar eye painted black * Sidewalls painted RAL 9010 pure white ----Info: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available

Stanje: novo, največja dovoljena obremenitev: 29.850 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Last axle is a trailing steering axle with electro-pneumatic steering lock, activated by PIN in reverse gear * Additional lock for the trailing axle operated from the tractor unit for shunting purposes – no installation necessary on the truck side – assigned to PIN 10; the lock must be deactivated before driving on public roads ----Suspension: * Air suspension with raise and lower function and Ride-on-Road (RtR) feature ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck's display via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights activated via reverse gear * SmartBoard installed as an info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for extended-length lighting * LED beacon (removable) at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanised sheet steel mudguards * Swivel arm as carrier for connecting lines in front of the front panel ----Warning Package: * Mechanically adjustable warning sign package ----Low Loader Platform: * 50 mm floor covering made from larch / Douglas fir instead of spruce / fir * Rear bevel – 700 mm long – on the semi-trailer platform to the low-bed section with checker plate covering, and at the end a perforated strip for attaching aluminum approach ramps * Tread plate covers over the wheels Nsdpfx Absykx I He Holc * SP combo package: toolbox with 45° corners made from galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, located on the semi-trailer platform approx. 2,480 x 500 mm * Folding lid on top as well as side doors in the angled corners * Foldable aluminum side boards 500 mm high on the semi-trailer platform, including foldable and removable rear stanchions * Inserted aluminum rear wall, 150 mm high * Second kingpin position * Preparation for container locking * Preparation for 3 recesses in the approach bevel from the low-bed to the gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load Securing: Semi-trailer platform: * In the front corners and front, 50 mm drilled holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the sides towards the approach slope * Perforated outer frame, 45° folded with hole pattern for lashing points (2 t lashing points every 480 mm) * On each side, 2 x 6.3 t retractable lashing rings recessed in the outer frame Low-bed platform: * 2 x 16.5 t lashing rings centrally positioned directly in front of the approach ramp to the gooseneck and recessed * On each side, 3 pairs of 13.5 t lashing rings and 5 pairs of 10 t lashing rings recessed in the outer frame * On each side, 4 stake pockets recessed in the outer frame * Profifix lashing rail in the center along the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From the end of the last rigid axle to the rear crossmember, W = 770 mm, D = 270 mm (on each side, 2 x 6.4 t lashing rings solid welded in the excavator arm rest) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps, approx. 3,200 x 750 mm * Load capacity 13 t per ramp (load capacity 26 t/pair) * Hydraulic ramp

Stanje: novo, največja dovoljena obremenitev: 29.850 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as trailing steering axle with electro-pneumatic steering lock via reverse gear PIN * Additional trailing axle lock, operable from the cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10; lock must be disengaged before driving on public roads ----Suspension: * Air suspension with lift and lowering function as well as RtR function ----Electrics / Lighting: * Tire pressure monitoring system with display option in truck instrument cluster via EBS signal – no truck-side installation required * LED rear lights 12 / 24 V * Flashing side marker lights * LED reverse lights, activated via reverse gear * SmartBoard mounted as an infotool with pressure sensors exclusively for total axle load indication * 7-pin socket at the rear for overlength lighting * Removable LED beacon at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing gears * Galvanized steel mudguards * Swivel arm as a carrier for connection cables in front of the front bulkhead ----Warning System Package: * Mechanically adjustable warning sign package ----Low Loader Platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear inclined section – 700 mm long – on the saddle platform to the low-bed with checker plate surface and at the end a perforated strip for hanging aluminum loading ramps * Tread plate covers above the wheels * SP-Combo Package: Tool box with 45° corners, made of galvanized steel and additionally powder-coated in RAL 9006 white aluminum, on the saddle platform approx. 2,480 x 500 mm * Hinged lid on top and side doors in the slanted corners * Fold-down aluminum side walls, 500 mm high, on the saddle platform, including rear stakes, foldable and removable * Inserted aluminum rear wall, 150 mm high * 2nd kingpin position * Prepared for container locks * Prepared for 3 mounting shafts in the inclined section from the low-bed to the gooseneck * Prepared for retrofitting fold-out supports for 3 m extension by welding in receptacles on the outer frame ----Load Securing: Saddle Platform: * Front corners and forward 50 mm bores for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor towards the inclined ramp * Perforated outer frame, 45° angled with hole pattern for tie-downs (2 t lashing points every 480 mm) * Each side with 2 x 6.3 t retractable lashing rings recessed in the outer frame Low Loader Platform: * 2 x 16.5 t lashing rings centered directly before the inclined section to the gooseneck, recessed * Each side with 3 pairs 13.5 t and 5 pairs 10 t retractable lashing rings recessed into the outer frame * Each side with 4 stake pockets recessed in the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From end of last rigid axle to end crossmember W = 770 mm, D = 270 mm (each side with 2 x 6.4 t lashing rings permanently welded into the excavator arm rest) ----Ramp: Nledpfjykx I Tex Ab Hoc * Hydraulic one-piece “ALLTEC” aluminum ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per set) * Hydraulic ramp shifting on sliding tube for ramp shaft ----Hydraulics: * Hydraulic flow divider in the trailer (for lorry hydraulic pump output exceeding 40 l/min up to max. 250 l/min), climbing strips on t

Stanje: novo, največja dovoljena obremenitev: 10.500 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * First inspection (ETÜ) - TA -R 14.4 ----Brake System: Nlsdpfx Aex Ipbajb Hoc * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by approx. 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange-type towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal (without truck-side installation) * 15-pin electrical connector * LED rear lights 12 / 24 V * Removable LED beacon at rear ----General Attachments: * Landing leg at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, externally mounted on the front right end wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * Preparation in front of the bulkhead for later installation of container locks * Bolted smooth steel bulkhead * Foldable steel side walls with trapezoidal profile, with drop-side spring assist * Removable steel rear wall, stowable inside at the front of the bulkhead when not in use * Bolted rear stanchions * Rear ramp bevel approx. 860 mm ----Flooring: * 50 mm softwood flooring * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the ramp bevel and on the exterior of the low loader platform (from front bulkhead to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each of the front and rear corners * Various drillings in the front and rear cross members for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring assistance for single-person operation, approx. 2,750 x 870 mm (collapsible to 20 mm thickness) ----Paint Finish: * Chassis, drawbar, front wall, tailgate, and ramps hot-dip galvanized * Axles, springs, air tanks, and flange eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * Reinforced and certified superstructure according to EN 12642 XL, including load securing certificate * Subject to errors and prior sale * New vehicle with manufacturer’s warranty ----Delivery time: Vehicle is immediately available ex Eggerstorf

Stanje: novo, največja dovoljena obremenitev: 8.770 kg, Leto izdelave: 2025, ABS Müller Mitteltal ETÜ TA R 11.9 Tandem Low Loader with Many Extra Features Equipment: - 2 spring-assisted lifts for 400mm high steel side walls Njdpsxcxmfsfx Ab Holc - Reinforced and certified superstructure according to EN 12642 XL load securing certificate - 10 UVV lashing hoops in the existing perforated pattern in the outer frame - Additional clamped wooden floor - 235/75R17.5 tyres - 4 BPW axles instead of GIGANT - Platform extension by 870 mm to a total of 6,270 mm - One-piece ramps with hot-dip galvanized anti-slip grating - Lockable toolbox with 45 kg load capacity Paintwork: - Wheels: silver - Chassis / front wall / drawbar / rear wall / stakes / ramps: hot-dip galvanized - Axles / springs: black - Side walls: RAL2011 deep orange We will be happy to offer you suitable financing, hire purchase, or leasing solutions. Delivery or shipping available by arrangement. We always have a selection of new equipment in stock and demo units available. Feel free to contact us! We rent vehicles with or without drivers, as well as machinery. A wide range of used machines and equipment always available. Subject to technical modifications, errors, and prior sale.

Stanje: rabljeno, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 06/2024, skupna širina: 2.550 mm, Leto izdelave: 2023, Müller Mitteltal KA-TA-R 11.9 Tandem 3-Way Tipper with many extras. Gross weight: 11,900 kg. Standard payload approx.: 8,750 kg. Internal dimensions: 5,000 x 2,420 x 500 mm. Tyres: 385/55R19.5. 4-coat single-color paint. Wheels: silver. Chassis/underrun protection: hot-dip galvanized. Platform with front wall: hot-dip galvanized. Axles/springs/air reservoir, etc.: black. Side and rear wall: RAL 2011 deep orange. Reinforced and certified superstructure according to EN 12642 XL including load securing certificate (only in combination with 500 mm high steel side walls). Rear stanchions bolted, hot-dip galvanized, without topcoat. Lashing points LC 5,000 daN, recessed at the front. Mesh hooks integrated laterally and at the rear into the locks of the central locking for the base side wall, as well as an additional 2 pieces on the front wall. BPW axles instead of GIANT. Tipping platform with fixed-mounted front wall in hot-dip galvanized version, with bolted, galvanized rear stanchions, without additional coating (not on HARDOX floor). Due to the system, waviness may occur during hot-dip galvanizing, especially on wide floor plates – warranty claims for this are excluded. Tyres 385/55R19.5 instead of 235/75R17.5 (floor and coupling height + approx. 110 mm, Code 08.940, ramp length 3,570 mm required). 1 piece plastic toolbox, black, lockable, W=750 x H=350 x D=300 mm (45 kg payload with evenly distributed load), mounted: on the chassis frame on the right in direction of travel. 1 pair of aluminium loading ramps without wheel channel (8 t/pair), 3,570 x 400 x 105 mm, suitable for rubber-tyred and tracked vehicles, 55 kg/piece. Two-step access in front of the front wall, left side in direction of travel (hot-dip galvanized). Connecting lines extended for agricultural and forestry towing vehicles. Further information New: No Nsdpfx Absvy Tvtj Hjlc

Stanje: novo, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, Oprema: ABS, dvižna zadnja plošča, Reference number for enquiries: 31943-O * NEW VEHICLE – soon available in your desired color. Müller-Mitteltal KA-TA-R 11.9 Tandem Low-bed Three-way Tipper Trailer with Ramps * Tyres: 385/55 R19.5 (4 units), BPW axles, parabolic springs, drum brakes * GVW: 11,900 kg, payload: 8,750 kg * Tyre pressure monitoring with in-cab display via EBS signal * EBS instead of ABS, 24 volts * EBS multi-voltage system for 24V and 12V vehicles (e.g., tractors) * Side marker lights with indicator activation * LED lighting system for 12V and 24V * 2 additional LED reversing lights * Floor galvanized, 5m x 2.42m, 0.5m side walls, laser-welded, swinging, folding, and removable * Prepared for retrofitting sidewall extensions later * Lockable compartment under the tipping body for the drive-on ramps * Incl. aluminium ramps, 8t load capacity, 3.57m long, stowed in ramp compartment under tipper body * Floor and front wall hot-dip galvanized * 4 UVV lashing rings LC 5000daN front and rear + 8 recessed and foldable lashing eyes LC 3000daN evenly distributed in tipper floor * Drawbar infinitely height-adjustable, hot-dip galvanized, 40mm towing eye * Mesh hooks * Bolt-on, galvanized rear stanchions * Excavator bucket rest mounted on the front wall * One plastic toolbox, mounted right-hand side of chassis frame * Step in front of front wall ---- * We are Müller-Mitteltal authorized dealer ---- * Request a quote from us! * e.g. from €545 net/month for 60 months, no down payment, no residual value. An offer from our financing partner FM LeasingPartner ---- Our opening hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Nodpjzbfmkefx Ab Hslc Outside opening hours, available by appointment We speak German, English, Polish, and French WhatsApp Leasing, financing, and trade-in possible.

Stanje: rabljeno, največja dovoljena obremenitev: 8.650 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 07/2017, naslednji pregled (TÜV): 05/2026, dolžina tovornega prostora: 6.250 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Dodatne informacije 400 mm zložljive stranske stranice - Dvižni mehanizem za stranice s vzmetjo - Snemljiva zadnja stena Nlodpfx Ajy Hn D Rob Hsc - Velik komplet za pritrjevanje tovora - Perforirana letva na tovornem prostoru - Sprednja podporna noga nastavljiva po višini - Zadnje podporne noge zložljive - Plastična orodjarna skrinja - BPW osi - Vzmetne rampe z rešetko

Stanje: rabljeno, največja dovoljena obremenitev: 8.900 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 12/2011, naslednji pregled (TÜV): 09/2026, dolžina tovornega prostora: 6.000 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Dodatne informacije - Rampske površine z rešetko - Vzmetne rampe Nodpfszb Ua Tox Ab Hslc - Zložljive podporne noge - LED vzvratne luči - Vzmeti za stranske stene - BPW osi - Stranske stene 400 mm - Uporabna dolžina 6.000 mm vklj. z zadnjim prislonom cca 1.100 mm

Stanje: rabljeno, največja dovoljena obremenitev: 8.750 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, prva registracija: 06/2026, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, skupna širina: 2.550 mm, skupna višina: 970 mm, Leto izdelave: 2026, Oprema: ABS, Müller-Mitteltal KA-TA-R 11.9 ML / 024 Truck Tandem Three-Way Tipper - Tipper body: 5,000 x 2,420 mm (internal dimensions) - Side wall height: 500 mm - Floor made from fine-grain steel S 420 MC, 4 mm thick - Laser-welded fine-grain steel drop sides, fixed front wall - 2 pairs of folding lashing rings with lashing capacity LC 5,000 daN, 1 pair each recessed in front and rear of steel floor. 4 pairs of folding lashing rings with LC 3,000 daN recessed in the steel floor. - Net hooks integrated on the side and rear in the side wall mountings and in the front wall. - Reinforced and certified superstructure according to EN 12642 XL - 2 LED reversing lights at the rear of the trailer - ALU loading ramps without tracks, suitable for rubber-tyred and tracked vehicles (8 t/pair), 3,310 x 400 x 105 mm - Plastic toolbox - ALU air reservoir - BPW axles with S-cam brakes - Tyres: 235/75R17.5 Suitable for coupling height approx. 925 mm unladen +/- 150 mm Subject to prior sale and errors excepted! Nledpfx Asy S Nwvob Hoc Sale exclusively under our General Terms and Conditions Important Note – Important Information: Despite careful checking of all details in our offer, mistakes may occur. Some of these may be caused by transmission errors in the systems of different platform providers. Therefore, we emphasize that all information is provided without guarantee and is not legally binding. Legal Notice: This sales advertisement does not constitute an offer as defined by §145 of the German Civil Code (BGB). Rather, it is information for the initiation of a contract. All details are provided without guarantee and do not represent warranted characteristics.

Stanje: novo, največja dovoljena obremenitev: 12.200 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, Leto izdelave: 2026, * TM-TA 14.4: ----Brakes: * Wabco EBS braking system * Emergency release device for spring-actuated cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Ring: * Height-adjustable, hot-dip galvanized drawbar with ±150 mm adjustment * 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power connector * LED tail lights * RDÜ tire pressure monitoring system ----General Attachments: * Jost landing gear at the front * 2 x exterior drop-down support legs at the rear * Enclosed single plastic mudguards * Foldable A-sign at the rear * Plastic underrun protection buffer * Hot-dip galvanized front crash protection bar with integrated chain storage box, (W = 370 mm x D = 420 mm x H = 480 mm) left and right front ----Load Securing: * 2 x 5.3 t UVV lashing rings per side for attaching tensioning elements * Including 2 permanently mounted ratchet tensioners with chain box at the outer frame * Compensating chain on both sides with eyelet and quick-shortener, special Y-version, 6.3 t ----Skip Stops: * 2 repositionable skip stops for lateral centering of the skips * Front skip stops with pendulum stop, adjustable in 4 positions ----Paintwork: * Hot-dip galvanized chassis * Axles, springs, air tanks and landing gear painted in black ----Info: * Lashing force with load securing certificate * Subject to errors and prior sale * New vehicle with manufacturer's warranty Nlodpfx Abspk Dyxj Hec ----Delivery Time: * Available from approx. calendar week 38/2026

Stanje: novo, največja dovoljena obremenitev: 10.950 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, Leto izdelave: 2026, * ETÜ-TA-ER 14.4 Platform Trailer: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lifting and lowering device ----Drawbar / Flange Eye: * Drawbar height-adjustable by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (results in a B-dimension of approx. 8,080 mm) * 40 mm flange towing eye ---- Electrics / Lighting: * 15-pin power connector * LED lighting system 12 / 24 V * 2 additional LED reverse lights at the rear (activated by reverse gear) * 1 removable LED beacon (including bracket) at the rear * TPMS (Tire Pressure Monitoring System) Nlsdpfx Ajv D Tbkjb Hsc ----General Attachments: * Mechanically adjustable 3 m warning panel sets at front and rear * Support winch at front * External folding supports at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm, one on each side left & right * Side underrun protection * Rear underrun protection * Plastic quarter fenders ----Loading Area: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable for 3 m container external width) and lockable; locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN compliant) with a total external width of 3,000 mm ----Load Securing: * Perforated outer frame approx. 45° bent with 2 t lashing force every 480 mm * Installation of 3 t lashing brackets possible every 600 mm - 5 x 3 t UVV-lashing brackets mounted per side * In each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end crossmember) * Various drillings in front wall and end crossmember for 1.2 t lashing options ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair) suitable for rubber-tired and tracked vehicles * Storage compartment under the loading platform at the rear, integrated into the chassis ----Paintwork: * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tanks, front support winch and flange towing eye painted in a shade of black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from CW 39/2026

Stanje: novo, največja dovoljena obremenitev: 12.200 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, Leto izdelave: 2026, * TM-TA 14.4: ----Braking system: * Wabco EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Flange eye: * Height-adjustable, hot-dip galvanised drawbar +/- 150 mm * 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power plug * LED tail lights * RDÜ tyre pressure monitoring system ----General attachments: * Jost landing gear at the front * 2 x external drop supports at the rear * Closed individual plastic mudguards * Foldable "A" sign at the rear * Plastic underride protection buffer * Hot-dip galvanised underrun guard with integrated chain storage box (W=370 mm x D=420 mm x H=480 mm) front left & right ----Load securing: * 2 x 5.3 t UVV lashing rings on each side for attaching tensioning elements ----Container stops: * 2 removable container stops for lateral centring of the containers * Front container stops with 4-position pivoting stops ----Paintwork: * Hot-dip galvanised chassis * Axles, springs, air tank and landing gear painted in black Nedol Thyqopfx Ab Helc ----Information: * Errors and subject to prior sale * New vehicle with manufacturer's warranty ----Delivery time: * Available from approx. week 38/2026