Drugi

Hoeflon C4e Minikran - Vorführgerät

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Maximum speed: 80 km/h (legal) Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Turning radius king pin to rear approx.: 2,100 mm Coupling height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Ppedpfxeizu Nte Agfsp Load height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific legislation: Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform approx. 9,600 mm in length with rear bevel approx. 900 mm x 6°. Loading area after gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair of two-piece AXS steel ramps, approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps individually hydraulically adjustable by approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle according to technical datasheet: C470319 Maximum gradient angle with lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion Load index 143/141J (144/144F) Brake System: WABCO EBS-E brake system according to EU regulations. No connecting cable to the tractor unit included. Lighting System: 24V lighting system in "ASPÖCK-NORDIK full LED" version according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation) Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). 6-Coat Paint Treatment: Entire steel structure shot-blasted after welding. 1 coat zinc-based primer, 1 coat adhesion primer. Topcoat consisting of 2 layers of 2K paint (acrylic) in a single RAL shade of choice, followed by cavity sealing with special wax. Rims in silver. Multi-colour and special coatings available at extra charge. Steel Construction: High-strength fine-grain steel structure. Steel grades: S355J2+N/S355MC (min. yield strength 355MPa) S690QL/S700MC (min. yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG-welding process to EN ISO 4063. Shielding gas M21 according to EN ISO 14175 Front bulkhead made of steel, detachable, approx. 400 mm high Connector strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. Anderson socket at the front connection strip. Rema 78051-00 & Amp. 150 V. Cable for supplying the electro-hydraulic power unit and/or

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin Podpfsiu Er Aox Agfepp - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: novo, Leto izdelave: 2025, Hoeflon Mini dvigalo C6e - Nova naprava Močan vsestranski stroj Rok dobave: takoj na voljo. Kapaciteta: 3000 kg Maks. vrtljivost: 13,70 m x 210 kg Psdet Il Dbjpfx Agfspp Največja višina dviga: 11,5 m, z možnostmi do 16,40 m Mere D x Š x V: 2,98 m x 0,77 m x 1,88 m Mere z vključenim vitlom in iztegljivim krakom: 3,20 m x 0,77 m x 2,00 m Skupna teža: 2850 kg Sistem droga: cilindrični in verižni sistem Kot iztega: -5 - 83 stopinj Vrtenje: 360 stopinj Hitrost: 2,2 km/h Motor/Baterija: OX Power baterija Kot nagiba: 15 stopinj Pritisk na tla: 0,79 kg/cm2 Vključene posebne opcije: Fly-Jib Podaljšek ramena, nastavljiv do 30° Zložljive podporne noge Vitlo: 3.000 kg

Stanje: novo, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.360 mm, skupna širina: 2.550 mm, skupna višina: 1.800 mm, Leto izdelave: 2021, Oprema: ABS, Zamenljivo podvozje polpriklopnika za 40’, 2x 20’, 1x 30’, 1x 40’HC kontejnerje * Dvižna os * Zadnji del pnevmatsko raztegljiv za 1360 mm Pjdpfekc T Ngjx Agfopp * SAF osi z disk zavorami * Podporniki Jost * Wabco Trailer EBS-E, ABS * Haldex Colas zračni sistem * Zagozde za kolesa ----Številka vozila 6945 -----Pridržujemo si pravico do napak in vmesne prodaje Podpora prek WhatsApp na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite preko WhatsAppa Whatsapp Whatsapp

Stanje: novo, Leto izdelave: 2024, Hoeflon Mini Crane C10e – New machine The Powerful All-rounder Pjdpfxjrbdh Ee Agfepp Delivery time: on request Capacity: 4,000 kg Max. working radius: 13.70 m x 500 kg – with options: 19.80 m x 209 kg Maximum lifting height: 16.30 m, including options: 22.00 m Dimensions L x W x H: 3.93 m x 0.80 m x 1.97 m Dimensions including winch and jib: 4.15 m x 0.80 m x 2.07 m Total weight: 4,400 kg, including options 4,700 kg Jib arm weight: 205 kg Jib angle: 5 – 83 degrees Slewing: 360 degrees Drive system with remote control: 1st gear: 1.1 km/h, 2nd gear: 2.3 km/h, 3rd gear: 2.9 km/h Electric drive: 400 V Inclination angle: 20 degrees Optional special equipment: Fly jib Extension section, 30° adjustable Winch: 4,000 kg Custom paintwork

Stanje: novo, Leto izdelave: 2023, Oprema: pogon na vsa štiri kolesa, Haulotte Compact 10DX - New Unit Delivery time: on request Ppsdpomv Natjfx Agfjp Colour: Haulotte Standard (RAL1006) Delivery to your desired address is possible. Working height: 10.28 m Platform height: 8.28 m Maximum load capacity: 565 kg Platform length: 2.45 m Platform length with extension: 3.7 m Platform extension: 1.2 m Platform width: 1.45 m Transport height: 1.59 m Height (stowed): 2.44 m Width: 1.78 m Length: 3.17 m Wheelbase: 1.84 m Standard Features: * All-wheel drive, steerable front wheels * Drive motor lockout * Foam-filled all-terrain tyres * One-sided 1.2 m platform extension * Removable control panel on platform * 3° tilt sensor * Automatic outrigger levelling * Horn * Hour meter * 12 V 74 Ah batteries * Hydraulic brakes * Manual emergency lowering feature * Anchorage points for fall protection * Towing and crane lugs * Side guards Optional Equipment: * Non-marking tyres * Power outlet on work platform * Swing gate * Hydraulic generator 3.5 kW * Biodegradable hydraulic oil * Cold climate kit * Prepared for tracking system* * Reversing acoustic alarm * Drive warning signal * Rotating beacon * Work lights * Foldable guardrail* * Custom colours (RAL) *Factory fit only; not retrofittable on stock units. 24 months manufacturer’s warranty on labour and spare parts.

Stanje: novo, Leto izdelave: 2024, obratovalne ure: 10 h, Oprema: pogon na vsa štiri kolesa, Hoeflon Mini Crane C4e - New Unit Multifunctional Compact Crane Delivery time: approx. 3 months Capacity: 2,350 kg Maximum Slewing Radius: 11.7 m at 144 kg Max. Lifting Height incl. options: 15.1 m Dimensions (L x W x H): 2.8 m x 0.75 m x 1.82 m Dimensions incl. winch and jib: 3.04 m x 0.75 m x 1.95 m Total weight: 1,900 kg (with options: 2,150 kg) Mast system: Cylinder and chain system Ppedpfxstrh T Ee Agfjp Jib angle: -5 to 83 degrees Slewing: 360 degrees Drive system: with remote control 1st gear: 1.2 km/h 2nd gear: 2.4 km/h Engine: Yanmar 3-cylinder, 1,500 rpm Inclination angle: 20 degrees Ground pressure: 0.59 kg/cm² Optional special equipment: Fly jib Winch: 3,000 kg Extension section, 30° adjustable Foldable outriggers Custom color (RAL)