Delovna platforma

HAULOTTE Compact 10 DX

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2020, številka stroja/vozila: 2455818, dvižna višina: 8.060 mm, skupna masa: 3.675 kg, vrsta goriva: dizel, barva: rumena, Oprema: UVV varnostni pregled, Technical specifications: * Working height: 10.06 m Cpsdpfx Aotw U Ngodreu * Platform height: 8.06 m * Maximum climbing ability: 25% * Maximum load capacity: 450 kg * Platform length: 2.45 m * Platform length with extension: 3.7 m * Platform extension: 1.20 m * Total weight: 3675 kg * UVV inspection new Fully functional, general signs of use

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, Leto izdelave: 2025, 3-axle MULTIMAX *PLUS low-loader semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Gross weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Neck length approx.: 3,900 mm Neck width approx.: 2,480 mm King pin steering radius to rear approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: * Loading platform width approx.: 2,540 mm Deck height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm *Gross weight depending on fifth wheel load: Yes Special permit required if country-specific regulations are exceeded. Technical description: Gooseneck: Gooseneck in SNT design for optimized load bed length, length approx. 3,900 mm, rear sloped approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Cpjdpfx Aoizu Ntedrou Load platform: Load platform, length approx. 9,600 mm with rear slope approx. 900 mm x 6°. Section of platform after the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair of two-piece AXS steel ramps, length approx. 4,920 mm, width approx. 900 mm. Open grating surface. Hydraulically folding ramp tips. Each ramp hydraulically adjustable sideways approx. 235 mm outward and approx. 365 mm inward. Maximum load and approach angle according to technical data sheet C470319. Maximum ramp angle with lowered load platform: 9°. Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg. Air suspension with lift and lower valve. Axle tools included. Tyres: 235/75 R 17.5 3PMSF twin tyres. Manufacturer at our discretion. Load index 143/141J (144/144F). Brake system: WABCO EBS-E braking system according to EU regulations. Without connection cable to tractor unit. Lighting: 24-volt lighting system "ASPÖCK-NORDIK full LED" version in accordance with EU regulations (ASS 3). Metallisation: Complete HRM metallisation (High Resistance Metallisation). Entire steel structure shot-blasted, then hot-finish coated with ZINACOR 850 (Zinc 85% - Alu 15%). 6-coat painting finish: Whole steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Final painting with 2 coats of two-component acrylic paint in a single RAL colour of choice, then cavity sealing with special wax. Rims in silver. Multi-colour and special paint at extra charge. Steel construction: Made from high-tensile fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Welders certified to DIN-EN 287-1. Welding procedure: MAG according to EN ISO 4063. Shielding gas M21 according to EN ISO 14175. Front bulkhead made of steel, removable, approx. 400 mm high. Supply line junction box for tractor unit mounted at the height of the outer frame profile. ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin assignment differs from the ISO standard, please inform us. Anderson socket at the front connection bar. (Rema 78051-00 & Amp. 150 V.) Cable for powering the electro-hydraulic unit and/or the electric cable winch (35 mm²,

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2020, številka stroja/vozila: 2455828, dvižna višina: 8.060 mm, skupna masa: 3.675 kg, vrsta goriva: dizel, barva: rumena, Oprema: UVV varnostni pregled, Technical specifications: * Working height: 10.06 m * Platform height: 8.06 m Cpodpfx Ajtxxcaodrju * Maximum climbing ability: 25% * Maximum load capacity: 450 kg * Platform length: 2.45 m * Platform length with extension: 3.7 m * Platform extension: 1.20 m * Total weight: 3675 kg * UVV inspection new Fully functional, general signs of use

Stanje: zelo dobro (rabljeno), Funkcionalnost: popolnoma funkcionalen, Leto izdelave: 2014, obratovalne ure: 2.200 h, barva: originalen, Oprema: pogon na vsa štiri kolesa, Na prodaj: škarjasto dvigalo HAULOTTE Compact 10 DX, letnik 2014. Dvigalo uvoženo, nerabljeno v državi. Delovnih ur: 2232. Delovna višina: 10,6 m. Višina platforme: 8,7 m. Nosilnost platforme: 450 kg. Pogon 4x4. 3 hitrosti vožnje. Zmožnost premagovanja naklonov do 40 %. Hidravlične stabilizacijske podpore – avtomatsko raztegljive. Prilagojeno za delo pri vetru do 12,5 m/s. Motor KUBOTA – moč 25 KM. Lastna masa: 3400 kg. Dimenzije delovne platforme: dolžina 2,45 m + balkon 1,20 m, širina 1,45 m. Transportne mere: dolžina 3,20 m, širina 1,80 m, višina 2,60 m. Neto cena: 455.000 PLN + 23% DDV. Ogled možen na 62-200 Gniezno, ul. 3 Maja 55. Codpfox Hqfwex Adrjpu

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: Cedpfoiu Er Aox Adrspu - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)

Stanje: rabljeno, Leto izdelave: 2023, obratovalne ure: 10 h, Oprema: pogon na vsa štiri kolesa, Haulotte Compact 10DX – Demo Unit Delivery time: Immediately available. Colour: Haulotte Standard (RAL1006) Delivery to your desired address is possible. Working height: 10.28 m Platform height: 8.28 m Maximum load capacity: 565 kg Platform length: 2.45 m Cjdetkcg Nspfx Adropu Platform length with extension: 3.7 m Platform extension: 1.2 m Platform width: 1.45 m Transport height: 1.59 m Height when retracted: 2.44 m Width: 1.78 m Length: 3.17 m Wheelbase: 1.84 m Standard equipment: * All-wheel drive, steerable front wheels * Drive motor disconnect * Foam-filled, all-terrain tyres * 1.2 m one-sided platform extension * Removable control panel on platform * 3° tilt sensor * Automatic outrigger levelling * Horn * Hour meter * 12 V – 74 Ah batteries * Hydraulic brakes * Manual emergency lowering * Lanyard anchor points for fall protection * Towing and lifting lugs * Side protection Optional additional equipment: Beacon/rotating warning light Work lights 220V power supply to basket/platform incl. residual-current device (RCD) Delivered with new statutory safety inspection (UVV).

Stanje: rabljeno, največja dovoljena obremenitev: 44.980 kg, skupna masa: 58.000 kg, konfiguracija osi: 3 osi, prva registracija: 09/2024, naslednji pregled (TÜV): 09/2025, skupna širina: 2.550 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt of the equipment list. Complete equipment details available upon request. Chassis, cranked * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, robust outer frame * 4-axle configuration. Wheel arch covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection mounted, made of anodised aluminum * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special design in the cranked area for maximum low-bed length in combination with AluLeg drop supports instead of telescopic landing gears, maximum rear swing radius of the tractor unit approx. 2,100 mm Special superstructure with rear stake extension * Self-supporting aluminium roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable to approx. 4,200 mm * Three sliding stakes per side with spring-assisted tension relief * Additional central stake locks in the roof beam and parking position, operated via pull cord and spring latch * Mechanically height-adjustable roof lift, adjustment height approx. 400 mm, can be operated from either side or single side without needing to open the opposite side and doors Codpfslthguox Adropu * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with stake height adjustment * Front overlap at bulkhead for driving under tarpaulin up to an overall height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on each side, 450 mm pockets below, above 4 rows of single pockets * In the high bed, only 3 rows of slats. Intermediate distances evenly distributed Floor * approx. 27 mm special water-resistant bonded beech plywood, non-slip surface * Steel plate in wheel arch area * Forklift accessible per DIN ? standard * Outer frame surface flush Brakes * WABCO air brake system with EBS complying with EC Directive 71/320 EEC incl. PREV (park-release safety valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer with drum brakes, low loader specification * Air suspension with raise/lower function, total lift approx. 230 mm * Third and fourth axles are friction-steered trailing axles with electrical and mechanical locking Twin tires * 235/75 R 17.5, -16, incl. spare wheel holder. Without spare wheel Paintwork * Chassis in RAL 3002 red, solid color * Central stakes and axles KTL coated black * Corner posts galvanized finish * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork solid color per RAL shade Included special equipment * Air suspension with ECAS control, operated at the trailer * Oversize signage front and rear, galvanized, infinitely extendable, with marker lights incl. plug-in sockets for revolving beacons (small panels) * Additional unlocking for sliding roof frame from outside * 4 stake adapters for special outer frame profile, for flexible locking of central stakes * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, oversize/height version, flat hooks, tarpaulin folds, closures with safety pawl / OCS * Left rear telescopic plug-in socket for revolving beacon incl. beacon * Outer frame for machine transport with approx. 64 securing points in 2,000 kg, 3,000 kg and 10,000 kg versions, according to construction release drawing * 1

Stanje: novo, Leto izdelave: 2024, Oprema: pogon na vsa štiri kolesa, Hoeflon Mini Crane C4e - New Unit Multifunctional Compact Crane Delivery time: approx. 3 months Capacity: 2,350 kg Maximum Slewing Radius: 11.7 m at 144 kg Max. Lifting Height incl. options: 15.1 m Dimensions (L x W x H): 2.8 m x 0.75 m x 1.82 m Dimensions incl. winch and jib: 3.04 m x 0.75 m x 1.95 m Total weight: 1,900 kg (with options: 2,150 kg) Mast system: Cylinder and chain system Jib angle: -5 to 83 degrees Slewing: 360 degrees Drive system: with remote control 1st gear: 1.2 km/h 2nd gear: 2.4 km/h Engine: Yanmar 3-cylinder, 1,500 rpm Inclination angle: 20 degrees Ground pressure: 0.59 kg/cm² Optional special equipment: Fly jib Cpedpfx Aoi N Uynedrju Winch: 3,000 kg Extension section, 30° adjustable Foldable outriggers Custom color (RAL)

Stanje: novo, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.360 mm, skupna širina: 2.550 mm, skupna višina: 1.800 mm, Leto izdelave: 2021, Oprema: ABS, Zamenljivo podvozje polpriklopnika za 40’, 2x 20’, 1x 30’, 1x 40’HC kontejnerje * Dvižna os * Zadnji del pnevmatsko raztegljiv za 1360 mm Csdpekc T Ngofx Adrspu * SAF osi z disk zavorami * Podporniki Jost * Wabco Trailer EBS-E, ABS * Haldex Colas zračni sistem * Zagozde za kolesa ----Številka vozila 6945 -----Pridržujemo si pravico do napak in vmesne prodaje Podpora prek WhatsApp na voljo! Za vprašanja o vozilu ali dodatne informacije nam pišite preko WhatsAppa Whatsapp Whatsapp

Stanje: novo, skupna masa: 41.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.360 mm, skupna širina: 2.550 mm, skupna višina: 1.800 mm, Leto izdelave: 2021, Oprema: ABS, Zamenljivo podvozje polpriklopnika za 40', 2x 20', 1x 30', 1x 40'HC kontejnerje * Dvižna os * Zadnji del pnevmatsko izvlečen za 1360 mm Cedpfskbvvijx Adropu * SAF osi z disk zavorami * Jost podporniki * Wabco Trailer EBS-E, ABS * Haldex Colas pnevmatski sistem * Podložni klini ----Številka vozila 6915 -----Pridržujemo si pravico do napak in vmesne prodaje Na voljo WhatsApp podpora! Za vprašanja o vozilu ali dodatne informacije nam pišite preko WhatsAppa Whatsapp Whatsapp