Polpriklopnik z nizkim ležiščem za prevoz gradbenih strojev

Meusburger carrellone centinato buche 4assi usato

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 27.000 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.300 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 235/75 R17.5, barva: siv, obratovalna teža: 11.000 kg, Oprema: ABS, Chassis: - Welded steel frame construction with front and rear frame cranks and a lowered bed without rear chamfer - Neck and kingpin plate 225 mm - Lowered bed rated for 25 t point load over 5 m - Outer frame closed to the outside with welded-on lashing rings for securing - Interchangeable 2" king pin - Rear hook-in rail for aluminum ramps Axles and Tyres: - BPW low-loader axles, each with a 10 t axle load, air bellows diameter 360 mm - Air suspension with lifting and lowering function, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights +100 mm - S-cam brakes 300/200 mm, asbestos-free brake pads - Automatic slack adjusters - IVTM tyre pressure monitoring - 9 tyres 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically forced steered via fifth wheel coupling Floor: - Multi-layer bonded board floor, 27 mm thick, flush with outer frame and longitudinal beams - Underside reinforced with GRP coating - 12 pairs of lashing rings welded in outer frame (8 pairs RUD 8 t – 6 pairs in the lowered bed as well as one pair each on the gooseneck and at the front of the rear aggregate – 2 pairs of 4 t lashing rings on gooseneck and rear aggregate) - 6 pairs of mushroom anchors in outer frame in the lowered bed - Storage box with lid in the lowered bed floor, front left and right Front Wall: - 25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Tarpaulin curtains on both sides with integrated vertical and horizontal belts (approx. 600 mm spacing) and stainless steel tension locks - Adjustable tarp straps (overcentre) up to loading width 4,000 mm including tarpaulin extension with press studs and Velcro fastener - Tarp extension in driving direction: 300 mm, in height: 750 mm - Incl. eyelets for separate tarpaulin extension piece - 1 pair of vertical tarpaulin pockets approx. 1,000 mm long, positioned in the lowered bed at the front crank - With belt pockets Rear Wall: - Steel rear portal frame with side tarpaulin hook-in device - Aluminum double-wing door, 25 mm thick - Both door wings fully foldable with door holders - Each door wing with aluminum double-joint hinge and two recessed grip hollows Front Corner Posts: Hsdpfx Apeiu Eu Nj Asfn - Roof height, bolted to front side Central Posts: - 3 pairs of infinitely adjustable folding posts - Posts are movable along the entire length via trolley - Middle posts in the lowered bed also fixable at the rear platform Roof: - EDSCHA sliding roof (galvanized) with cross beams movable in both directions (stacked forward inside the cargo area) - Rear portal cross beam swivels away - PVC tarpaulin roof without customs closure - Manually operated hydraulic lifting roof on both sides, lift 450 mm - Movable lifting roof in positions front (9x50) and rear (9x50), can be driven at increased height - Including tarpaulin extension and apron at rear - Roof can be cranked out 900 mm at front wall Accessories: - Extendable warning signs (removable at front and rear, with socket) incl. position lights up to loading width 4,000 mm - Storage for 4 warning signs on inside of front wall, top right and left - 1 aluminum ladder with holder 2,500 mm long on front wall - 2 rows of self-securing aluminum slats - Metal mudguards with splash flaps - 1 overnight parking plate and 1 ADR plate on rear wall - BEKAMAX central lubrication system with pump and grease class 2 for approx. 35 lubrication points - Electrohydraul

Stanje: rabljeno, lastna masa: 10.900 kg, največja dovoljena obremenitev: 43.600 kg, skupna masa: 54.500 kg, konfiguracija osi: > 3 osi, prva registracija: 04/2025, dolžina tovornega prostora: 8.700 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 855 mm, velikost pnevmatike: 245/70 r17.5, barva: siv, Leto izdelave: 2025, obratovalna teža: 10.900 kg, Oprema: ABS, Gooseneck, rigid, center tube design: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel floor with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Manually operated BPW landing legs - 550 mm long, 8° chamfer at end of gooseneck - Front wall including park position for rear wall, 400 mm high - Spare wheel holder mounted vertically on the front side of the gooseneck - 3 pairs of recessed lashing rings (LC 5,000 daN) in the loading area of the gooseneck - Aluminum side boards, 400 mm high, comprising 2x side boards each 3,150 mm long, and rear board with stanchions (galvanized) - Rectangular aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, center - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, left - 45’ aluminium toolbox with folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single-extendable: - Closed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel plate floor with anti-slip coating - Chamfered transition between fixed part and deck for bridging rails and wheel recesses Hodji Ai E Rjpfx Ap Ajfn - Excavator trough including elongated holes for load securing (LC 1,500 daN), length approx. 3,850 mm - Prepared for hydraulic ramps (electrical supply) - Rails to widen up to 3,000 mm - 8° chamfered vehicle rear, 550 mm long - Slide system for easy mounting/dismounting of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally on the loading area behind the gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally in the rear section of the loading platform - 1 pair of stanchion pocket rails approx. center of the loading area - 1 pair of stanchion pocket rails on the fixed part - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic double-folding ramps, 2,750+1,500x800 mm - Larch wood surface - Operated by remote control (wired and wireless) - Quick-change ramp (dismantling system) Chassis: - Axle brand: BPW ECO Max - 2 ride heights - 4 axles @ 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 x rigid axles and 2 x friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system by Knorr (according to EU standards with EBS-E) - Knorr TIM G2 (Trailer Information Module) - RSS (Roll Stability Support) stability control - Load-dependent lift axle on the first axle incl. starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning panels 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm - Securing points on gooseneck and on loading platform (alternatively on ramp, if available) included - Plug-in bulkhead at the end of the excavator trough - Electrohydraulic unit for ramp operation - Ramp control by wireless remote - Hydraulic rear support legs for stabilization during loading - 1 pair of additional reversing lights at the rear, activated when reversing - Larch wood widening planks (option)

Stanje: rabljeno, prevoženi kilometri: 432.500 km, moč: 294 kW (399,73 KM), prva registracija: 08/2012, vrsta goriva: dizel, velikost pnevmatike: 385/65 R22.5, konfiguracija osi: 8x2, gorivo: dizel, kapaciteta rezervoarja za gorivo: 500 l, barva: drugo, voznikova kabina: dnevna kabina, vrsta prenosa: mehanski, število prestav: 8, emisijski razred: Euro 5, vzmetenje: drugo, število sedežev: 2, skupna dolžina: 11.800 mm, skupna širina: 2.500 mm, skupna višina: 3.650 mm, dolžina tovornega prostora: 7.650 mm, širina tovornega prostora: 2.500 mm, Leto izdelave: 2012, obratovalne ure: 9.796 h, Oprema: klimatska naprava, spojka prikolice, zapora diferenciala, žerjav, = Dodatne možnosti in oprema = - Dvigalna os - Diferencialna zaklopka - Krmilna os = Opombe = Kabina Desnosmerni volan: ✓ Šasi Višina šasije: 100 cm Medosna razdalja: 195 cm (1-2) 440 cm (2-3) 140 cm (1-3) Prostornina rezervoarja za gorivo: 500 Znamka priklopa za prikolico: VGB Žerjav Dolžina žerjava: 16,10 m Število hidravličnih podaljškov: 6 Število opornih nog: 4 Daljinski upravljalnik: ✓ Kavelj za obremenitev: ✓ Nosilnost: 16,10 m Maksimalna nosilnost žerjava: 3100 kg pri 16,10 m Maksimalni doseg žerjava: 16,10 m Nadgradnja Vrsta nadgradnje: 20 ft = Dodatne informacije = Kabina: enostavna Prednja os 1: Velikost pnevmatike: 385/65 R22.5; Krmilna; Globina profila leve pnevmatike: 65%; Globina profila desne pnevmatike: 75%; Vzmetenje: listnato vzmetenje Prednja os 2: Velikost pnevmatike: 385/65 R22.5; Krmilna; Globina profila leve pnevmatike: 25%; Globina profila desne pnevmatike: 40%; Vzmetenje: listnato vzmetenje Zadnja os 1: Velikost pnevmatike: 315/80 R22.5; Dvojne pnevmatike; Diferencialna zaklopka; Globina profila leve zunanje pnevmatike: 80%; Globina profila desne zunanje pnevmatike: 65%; Vzmetenje: zračno vzmetenje Zadnja os 2: Velikost pnevmatike: 315/80 R22.5; Krmilna; Globina profila leve pnevmatike: 70%; Globina profila desne pnevmatike: 50%; Vzmetenje: zračno vzmetenje Maksimalna dovoljena masa: 36.000 kg Žerjav: Fassi F660 RA 2.26 HE Dynamic, leto izdelave 2012, za kabino Hfjdpexxba Tefx Ap Aon Raztegljiva nadgradnja: Da Registrska tablica: NJ12VWR = Informacije o podjetju = Za več informacij o tem vozilu nas pokličite na: ali nam pošljite e-pošto na: . Celoten pregled zaloge najdete na: . Ne pozabite se naročiti na naše novice, da boste tedensko prejemali informacije o naši zalogi.

Stanje: rabljeno, konfiguracija osi: > 3 osi, prva registracija: 10/2006, skupna širina: 2.850 mm, vzmetenje: drugo, velikost pnevmatike: 285/70R19.5, barva: črn, Leto izdelave: 2006, Oprema: ABS, = Dodatne možnosti in dodatna oprema = - Osrednje podmazovanje = Opombe = Faymonville Jeep prikolica D3 Letnik 2006. 1 x dvižna os. 1 x os s trenjem za krmiljenje / os s pomikom. Zračna vzmet. Maksimalna dovoljena tehnična masa: 56.000 kg. Faymonville STBZ-5VA Letnik 2006. Nihačna os. Odstranljiv sprednji del. Premikalna ploščad. Razširljiva platforma: 400 cm. Nosilna platforma: 650 + 400 cm. 50.000 kg nosilnosti sprednjega dela. Maksimalna dovoljena tehnična masa: 119.680 kg. = Dodatne informacije = Konfiguracija osi Dimenzije pnevmatik: 285/70R19.5 Zavore: bobnaste zavore Sprednja os 1: Dvojne pnevmatike; profil pnevmatike levo notranji: 15%; profil pnevmatike levo zunanji: 60%; profil pnevmatike desno notranji: 60%; profil pnevmatike desno zunanji: 60%; vzmetenje: zračno vzmetenje Sprednja os 2: Dvojne pnevmatike; profil pnevmatike levo notranji: 30%; profil pnevmatike levo zunanji: 30%; profil pnevmatike desno notranji: 40%; profil pnevmatike desno zunanji: 60%; vzmetenje: zračno vzmetenje Sprednja os 3: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 30%; profil pnevmatike levo zunanji: 70%; profil pnevmatike desno notranji: 60%; profil pnevmatike desno zunanji: 70%; vzmetenje: zračno vzmetenje Zadnja os 1: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 30%; profil pnevmatike levo zunanji: 60%; profil pnevmatike desno notranji: 40%; profil pnevmatike desno zunanji: 70%; vzmetenje: hidravlično vzmetenje Zadnja os 2: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 50%; profil pnevmatike levo zunanji: 50%; profil pnevmatike desno notranji: 30%; profil pnevmatike desno zunanji: 75%; vzmetenje: hidravlično vzmetenje Zadnja os 3: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 60%; profil pnevmatike levo zunanji: 60%; profil pnevmatike desno notranji: 60%; profil pnevmatike desno zunanji: 60%; vzmetenje: hidravlično vzmetenje Zadnja os 4: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 60%; profil pnevmatike levo zunanji: 60%; profil pnevmatike desno notranji: 40%; profil pnevmatike desno zunanji: 50%; vzmetenje: hidravlično vzmetenje Zadnja os 5: Dvojne pnevmatike; krmilna os; profil pnevmatike levo notranji: 70%; profil pnevmatike levo zunanji: 70%; profil pnevmatike desno notranji: 20%; profil pnevmatike desno zunanji: 70%; vzmetenje: hidravlično vzmetenje Teže Lastna teža: 36.600 kg Nosilnost: 99.400 kg Dovoljena skupna masa: 136.000 kg Finančne informacije Cena: Po dogovoru Hfsdsxbng Ejpfx Ap Aon Identifikacija Številka modela: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Podatki o podjetju = VSE CENE SO NETO ZA IZVOZ. (Joris Versteijnen NL-DE-GB, Wouter Greutink NL-DE-GB-ES-IT) Govorim rusko. Trudimo se po najboljših močeh zagotoviti točne informacije. Vendar iz objavljenih besedil ni mogoče izpeljati nobenih pravic.

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: > 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: Hodetphtmspfx Ap Ajfn BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: zelo dobro (rabljeno), konfiguracija osi: > 3 osi, dovoljena osna obremenitev (os 1): 11.200 kg, dovoljena osna obremenitev (os 2): 11.200 kg, dovoljena osna obremenitev (os 3): 11.200 kg, dolžina tovornega prostora: 14.600 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 880 mm, skupna dolžina: 14.600 mm, skupna širina: 2.550 mm, skupna višina: 880 mm, vzmetenje: zrak, velikost pnevmatike: 245 / 70 R17.5, barva: modra, Leto izdelave: 2008, Oprema: dvižna zadnja plošča, Color: Blue Loading capacity: 72,600 kg Loading floor height: 885 mm Extendable Braked Main Features Manufacturer: Goldhofer Model: STZ L6 65/80A Semi Low Loader with Ramps Chassis number: WG0STZL6A80030419 Year of manufacture: 2008 Weights / Loading Capacity King pin load: 26,000 kg Axle load: 11,200 kg Total axle load: 6 x 11,200 kg = 67,200 kg Gross vehicle weight (GVW): 93,200 kg Unladen weight: 20,600 kg Payload: 72,600 kg Axles Axle make: BPW Air suspension 1st axle fixed Axles 2–6 hydraulic steering Axles 1 & 2 liftable High/low valve WABCO braking system Tyres: 245/70 R17.5 Dimensions Length: 14,600 mm Extensions: +7,200 mm Maximum extended length: 21,800 mm Loading width: 2,550 mm Height: approx. 885 mm – 925 mm King pin height: +/- 1,350 mm Additional information • Operated via truck PTO • Lashing rings • Stake pockets • Partially wooden loading deck • Mechanical landing gear • Hydraulic loading ramps • Extendable loading floor • Rear bumper with lights • 3.5" king pin • Central lubrication • Oversize load marker boards • Radio remote control • Outriggers • Toolbox on gooseneck = Further information = General information Year of manufacture: 2008 Axle configuration Tyre size: 245/70 R17.5 Axle brand: BPW Eco Suspension: Air suspension Rear axle 1: twin tyres, lift axle, max. axle load 11,200 kg Rear axle 2: twin tyres, lift axle, max. axle load 11,200 kg, steered Rear axle 3: twin tyres, max. axle load 11,200 kg, steered Rear axle 4: twin tyres, max. axle load 11,200 kg, steered Rear axle 5: twin tyres, max. axle load 11,200 kg, steered Rear axle 6: twin tyres, max. axle load 11,200 kg, steered Weights Hjdpfxsx R Undj Ap Ajfn Unladen weight: 20,600 kg Payload: 72,600 kg GVW: 93,200 kg Functional Superstructure make: WABCO Loading platform height: 88 cm Extendable superstructure: Yes Condition Technical condition: very good Optical condition: very good Financial information Price: On request

Stanje: dober (rabljeno), prevoženi kilometri: 28.063 km, barva: modra, Leto izdelave: 2019, obratovalne ure: 4.535 h, Proizvajalec: Liebherr Tip: LTF 1045-4.1 Letnik: 2019 Hfodozb D Rhepfx Ap Asn Kapaciteta: 45 t Glavni dvižni krak: 35 m Jib/Podaljšek: 9,5 m Prevoženi kilometri: 28.063 km Delovne ure dvigala: 4.535 h Protiuteži: 9 t

Stanje: rabljeno, lastna masa: 10.600 kg, največja dovoljena obremenitev: 22.500 kg, skupna masa: 33.100 kg, konfiguracija osi: 3 osi, prva registracija: 12/1984, dolžina tovornega prostora: 11.900 mm, širina tovornega prostora: 2.730 mm, višina nakladalnega prostora: 950 mm, vzmetenje: jeklo, velikost pnevmatike: 7.50R15, barva: siv, prevoženi kilometri: 1.001 km, vrsta prenosa: drugo, voznikova kabina: drugo, Vehicle location: Bovenden, 3 axles, SAF axles, leaf suspension, lashing rings, split loading ramps (2-piece), mechanical ramps, side aluminium underrun protection, supports, twin tires Hfsdoi Rp A Nopfx Ap Asn Body: 3-axle low-loader semi-trailer with 2-piece mechanical loading ramps, loading length on lower platform approx. 8,900 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Stanje: rabljeno, prevoženi kilometri: 1.786.827 km, prva registracija: 09/2012, vrsta goriva: dizel, zavore: retarder, vrsta prenosa: polavtomatski, emisijski razred: Euro 5, Leto izdelave: 2012, Informatie in het Nederlands: SCANIA R560 V8 4X2 Trekker met Retarder Euro5 Type: Trekker Bouwjaar: 2012 Kilometerstand: 1.786.827 KM BTW-ID: BTW-voertuig, vermelde prijs is netto. Specificaties: V8-motor met turbo, 560 PK. Automaat met koppeling. Retarder. Hodpspmrdfjfx Ap Aefn Volledig uitgerust. Ruimtecabine. Euro5. Stalen vering voor en luchtvering achter. Vrachtwagen is in TOP staat en direct inzetbaar. Zeer krachtige truck. Wij kunnen wereldwijd transport regelen. VOOR ONS VOLLEDIGE AANBOD, BEZOEK ONZE WEBSITE: Aanvullende informatie: * Laadvermogen: 44.000 kg * Payload: 44.000 kg Extra opties: * Intarder * Retarder Tony Trucks B.V. | Meer foto's op Contact | Michel Kurt | Tel: | WhatsApp: | E-mail: Tony | Tel: | WhatsApp: Exportkosten | Informeer vooraf naar tarieven en procedures voor uw land. Locatie | Bergschenhoek (NL) | 130 km van de Duitse grens | 10 km van Rotterdam The Hague Airport. Disclaimer: Wijzigingen, tussentijdse verkoop en fouten voorbehouden. Vermelde prijzen zijn exclusief BPM en gelden uitsluitend voor export.

Stanje: novo, lastna masa: 13.250 kg, največja dovoljena obremenitev: 47.550 kg, skupna masa: 60.800 kg, konfiguracija osi: > 3 osi, vzmetenje: zrak, velikost pnevmatike: 245/70 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of flat lashing rings at the front of the loading area Cut-outs in the outer frame of the loading area for inserting tension straps Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Two-part steel ramps: One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering. Ramp with hydraulically folding and unfolding parts, hydraulic lifting system, and hydraulically adjustable position. Maximum load per pair: 40,000 kg Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Braking system: Braking system according to EU regulations with EBS-E (4S3M) without connecting lines to tractor unit Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer High-quality one-color two-component (2K) top coat in Novagrau Hedpjl Uxdkofx Ap Ajfn Rear section metallized and painted in RAL 9010 (pure white) Metallic paint not possible Electrical system: Electrical system according to EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections conforming to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel headboard approx. 400 mm high At the galvanized front connection strip, yellow-red air couplings 4 wheel chocks with holders at the headboard One spare wheel with holder in front of the headboard Electro-hydraulic power unit Rear and front remote steering via cable remote control with push-buttons, with single-track control of the axles Bracket at rear of gooseneck for ALU drive-on ramps European reflector signs (red-yellow) at trailer rear White reflective tape according to EU regulations at the sides, at the extension, and red at the rear At the gooseneck and on the ramps left and right, each with a holder for warning signs including socket One holder for beacon at trailer rear Galvanized folding supports under the loading platform chamfer Ramp operating valves fitted on the right side of the trailer Cover plates to bridge the gap between ramps and loading platform One mudflap at trailer rear Manual and description on USB stick Central lubrication system BEKAMAX (Pico) with general-purpose grease NLGI-2 and removable pump guard On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm The rear galvanized stakes are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350 x 400 x 400 on the gooseneck, box covers oil filler cap 4 pairs of WADER container pockets in the loading area for a