Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Multimax Satteltieflader - hydr. gelenkt

Stanje: novo, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, More vehicles available at Excerpt from the equipment features. Complete equipment list upon request. GOOSENECK Gooseneck in SNT design for optimizing the loading area length, approx. 3,700 mm long, rear with bevel approx. 1,000 mm x 10°. For tractor units: 4 x 2, 6 x 2, and 6 x 4. - Front wall made of steel, removable, approx. 400 mm high - ASPÖCK-UNIBOX at the front terminal strip with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches - Outer beams of gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN). - 1 pair recessed lashing rings at the rear of the gooseneck (LC 10,000 daN). - On the gooseneck, 1 pair of detachable ALU side boards, approx. 400 mm high, anodized. - On the gooseneck, one detachable ALU rear board, approx. 400 mm high, anodized. - Gooseneck fitted with approx. 40 mm thick hardwood flooring, checker plate over kingpin. - 3.5 inch kingpin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide. - Round NATO socket at the front terminal strip (Maeler & Kaege VG 96 917) - 2 pairs of lashing rings with retention spring, hanging from outside of gooseneck beams (LC 5,000 daN). LOAD AREA Extendable load area, approx. 8,800 mm long with rear bevel approx. 500 mm x 10°. Pneumatic locking with conical lock bolt and reinforced locking positions, supply lines protected in the extendable beams and automatically adjust to the respective load area length. - BPW axles and suspension, 1st axle forcibly steered (tracking), all other axles hydro-mechanically forced steered. 1st axle with electromagnetically controlled reverse lock via reverse gear and manual activation. Technical axle load: 12,000 kg each Air suspension with raise and lower valve. - 235/75 R 17.5 3PMSF twin tires - manufacturer of our choice - Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B - static test load = 50,000 kg - Continuous hardwood flooring approx. 50 mm thick on the load area and interrupted between the axles (increases coefficient of friction). - Long holes for attachable and adjustable bridge elements: - at the front of the load area - 1 sliding intermediate platform, approx. 300 mm wide, for the large cross-section extendable tube, checker plate surface. - front and rear with long holes for attachable and adjustable bridge elements. - 1 pair of lashing rings on the front cross member (LC 10,000 daN). - 7 pairs of recessed lashing rings in the outer frame of the load area, foldable outward (LC 10,000 daN). - Extensions (galvanized) extendable by approx. 230 mm per side (without timber planks). - 1 pair of mechanical rear supports. - Rear steering from front and rear via cable remote control, with single-track axles monitoring, without installation in the tractor unit. - TPMS tire pressure sensors installed in all wheels - Load area locking with conically welded locking profiles every 500 mm. - Locking control left and right on the trailer. - For the intermediate platform, approx. 300 mm wide, a mechanical lock to secure the platform on the extension. - 5 pairs of threaded blocks on the extendable beam for mounting M20 bolted rings (LC 5,000 daN). Cedpfxjxarmae Adnehd

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve Codpfotx Nwnsx Adnehd * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) Cjdpfx Aorgzv Nsdnshd * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck