Polpriklopnik kiper

LANGENDORF Stahlmulde 50m³*ALU-Felgen*Portal*1+3 Liftachse

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included Lodpjk Af Svjfx Ab Usak - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: novo, lastna masa: 15.420 kg, največja dovoljena obremenitev: 61.080 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.600 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: Extendable loading platform with rear chamfer approx. 500 mm x 8° 8 pairs of flip-out lashing rings 1 pair of recessed lashing rings at the front of the loading area Cutouts in the outer frame for securing straps Approx. 48 mm thick hardwood flooring; checker plate above the axles Two-Part Steel Ramps: One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically folding ramp sections, hydraulic lifting and hydraulic lateral movement. Max load per pair: 50,000kg. Landing Legs: • JOST landing legs (mechanical) with two-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: BPW axles and suspension, 4th and 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axle with electromagnetically operated reverse lock, activated by reverse gear and manually Tyres: 235/75 R 17.5 3PMSF Brake System: Brake system according to EU regulations with EBS-E (4S3M) Sockets and Lighting: Electrical system according to EU standards, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Connections per ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component (2K) zinc-rich primer High-quality single-colour 2K topcoat in MB 7350 Novagrau Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel Structure: High-strength fine-grained steel construction Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the front wall 2" king pin Ledpfx Abel Sl Izj Uoak Galvanized steel front wall approx. 400 mm high Yellow-red air couplings on the galvanized front connection panel 2 wheel chocks with holder on the front wall Mounting at the rear of the gooseneck for ALU approach ramps Bracket for beacon at trailer rear Galvanized supports under sloped area of load floor White reflective tape per EU regulations on sides, extension, and red at the rear Electro-hydraulic unit under the rear of loading platform Warning sign brackets including sockets left/right on gooseneck and rear plate Control valves for ramps mounted right side of trailer Mudflap at rear of trailer Manual and documentation on USB stick 3.5" loose king pin supplied On gooseneck: ALU side boards and rear wall, plug-in approx. 2,440 x 400 mm (LxH) Removable rear galvanized stakes (Body length approx. 2,560 mm) 3 pairs WADER container pockets for 1x 20'/30' or 1x 40' container 6 pairs stake pockets for 100 x 50 mm plug-in stakes in outer frame Galvanized extensions, extendable by approx. 230 mm per side Lift axle on front axle, controlled via TEBS E according to actual axle load and current payload Square climbing strips 20 x 20 mm every 200 mm on outer frame chamfer of load floor Checker plate coverings above the king pin and loading area...

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Lsdpfx Ajrigw Rob Ujak Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 13.500 kg, največja dovoljena obremenitev: 51.500 kg, skupna masa: 69.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r17.5, barva: siv, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimizing loading platform length, length approx. 3,700 mm Gooseneck rear with chamfering approx. 1,000 mm x 10° Lajdpfxok Ahugs Ab Uok Loading Platform: Telescopic loading platform, length approx. 8,800 mm, with rear chamfering approx. 500 mm x 10° Recess in the chamfer as well as into the loading platform to accommodate the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions Supply lines routed protected within the extendable beam, adapting to the respective platform length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps individually adjustable hydraulically approx. 235 mm to the outside and approx. 215 mm to the inside Axles and Suspension: BPW axles and suspension, two rigid axles, two steering trailing axles Electromagnetic reverse lock, activated via reverse gear and manually Air suspension with lift and lower valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO braking system, EBS-E in accordance with EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metalizing: Standard HRM metallization of the outer frame Complete steel structure shot-blasted, then visible defined surfaces metallized with ZINACOR 850 (Zinc 85% - Alu 15%) hot-refined Steel Construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified as per DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 as per EN ISO 14175 Accessories Included: Front wall made of steel, plug-in, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin 24N connection per ISO-11852, 24S connection per ISO-3731, 15-pin connection per ISO-12098 Round NATO socket on the front connection strip Cable to supply electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long) between trailer and tractor with connector (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the gooseneck's outer beam for a screwable lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck, 1 pair of plug-in side aluminium walls, approx. 400 mm high, anodized On the gooseneck, a plug-in aluminium rear wall, approx. 400 mm high, anodized 2" kingpin Gooseneck guide plate for fifth wheel, approx. 500 mm wide 4 wheel chocks with holder Holder for aluminium approach ramps Mechanical landing gear with 2-speed gearbox and crank Continuous hardwood floor approx. 50 mm thick on the loading platform, interrupted between axles Platform locking with conically welded locking profiles every 250 mm incl. tension plate Slotted holes at the front of the loading platform for attachable and adjustable bridging elements 1 intermediate table with recessed platform, approx. 300 mm wide for the draw-out tube with large cross-section, with sheet metal covering Front and rear with slotted holes

Stanje: rabljeno, številka stroja/vozila: VF9S27B2060041018, konfiguracija osi: 3 osi, prva registracija: 01/2006, skupna dolžina: 10.800 mm, skupna širina: 2.550 mm, skupna višina: 3.600 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5, barva: drugo, Leto izdelave: 2006, Oprema: ABS, Chassis Chassis height: 100 cm Kingpin / Fifth wheel diameter: 2 inch Kingpin / Drawbar height: 120 cm Tank Capacity (liters): 37,000 Number of compartments: 1 Compartment volume (liters): 37,000 Tank material: Aluminium Test pressure: 3.0 bar Maximum working pressure: 2.0 bar Powder: ✓ Fuel: ✓ = Further Information = Axle configuration Tyre size: 385/65 R22.5 Axle brand: Bpwecoplus Brakes: Disc brakes Suspension: Air suspension Axle 1: Lifting axle; Tyre tread left: 35%; Tyre tread right: 35% Axle 2: Tyre tread left: 70%; Tyre tread right: 75% Ledpfovk Dirox Ab Ujak Axle 3: Tyre tread left: 25%; Tyre tread right: 25% Weights Unladen weight: 6,000 kg Payload: 34,000 kg Gross vehicle weight: 40,000 kg Functional Body manufacturer: Spitzer Identification Registration number: C239102 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Stanje: rabljeno, številka stroja/vozila: 62728, konfiguracija osi: 3 osi, prva registracija: 01/2002, skupna dolžina: 11.700 mm, skupna širina: 2.500 mm, skupna višina: 3.600 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22..5, barva: drugo, Leto izdelave: 2002, Oprema: ABS, Réservoir Capacité (litres) : 30 000 Nombre de compartiments : 3 Ledpev I Sinefx Ab Uoak Volume des compartiments (litres) : 12 000 ; 6 000 ; 12 000 Code matériau : 1.4301 Matériau du réservoir : Inox Isolé : ✓ Pression d’épreuve : 4 bar Charge de service maximale : 3 bar Produits chimiques : ✓ = Informations complémentaires = Configuration des essieux Marque des essieux : Saf Freins : Freins à tambour Suspension : Suspension pneumatique Essieu arrière 1 : Dimension pneus : 385/65 R22.5 ; Profil pneu gauche : 20% ; Profil pneu droit : 20% Essieu arrière 2 : Dimension pneus : 385/65 R22.5 ; Profil pneu gauche : 10% ; Profil pneu droit : 30% Essieu arrière 3 : Dimension pneus : 385/65 R22.5 ; Profil pneu gauche : 10% ; Profil pneu droit : 20% Poids Poids à vide : 7 680 kg Charge utile : 30 320 kg PTAC : 38 000 kg Identification Numéro d’immatriculation : UVG949 = Informations sur l’entreprise = Pour plus d’informations sur cette unité, veuillez appeler : ou envoyer un e-mail à : . Un aperçu complet du stock est disponible sur : . N’oubliez pas de vous abonner à notre newsletter pour recevoir les mises à jour hebdomadaires de notre stock.