Drugo Nizki Nakladalnik nakup rabljenega (157)

Stanje: rabljeno, številka stroja/vozila: 0e87837859aec926e9db10456, lastna masa: 6.200 kg, največja dovoljena obremenitev: 11.800 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, prva registracija: 05/2018, velikost pnevmatike: 235/75 r17,5, Leto izdelave: 2017, Further Information Chassis: Steel welded construction, double cranked with low bed in front of and behind the axle assembly, low bed beveled for driving on, turntable with robust ball bearing slewing ring, foldable rear support, wheel chocks, side underrun protection, quarter shell mudguards. Lashing points: Over front axle: 2 pairs of ring lashing eyes each rated 5t at the front at the cranked part of the low bed / Rear axle: 6 pairs of lashing eyes laterally in the low bed each rated 8t. 6 pairs of lashing eyes each rated 5t between the longitudinal beams, pair of stake pockets recessed in the outer frame, inside dimension 70 x 40 mm, or alternatively to stake pockets, 5t ring lashing eyes embedded in the floor. Drawbar: Certified 40 mm towing eye Axles: BPW drum brake axles Brake system: 2-line compressed air braking system, spring-actuated parking brake, 2 fail-safe coupling heads at the front Electrics: 24 volts, multi-chamber lights, lateral yellow lighting, 2 white position lights at the front, 2 white/red lane marker lights at the rear, beacon with bracket, pair of illuminated warning panels extendable to 3,000 mm, 2 x 7-pin fail-safe connectors at the front Dkedpfx Afei Ri N Us Ujg Floor: Front crank with steel / chequer plate covering, stowage box recessed in the transition to the crank, track area and middle section between the beams with steel / chequer plate covering, rear slope with 70 mm softwood floor, low bed area including rear slope 5900 mm Ramps: Hanging rail for aluminum ramps across the entire width, as U-profile across the entire width. Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg, stowage compartment for ramps between beams Approval: Contour marking with reflective strips according to ECE R 048, white at sides and red at rear

Stanje: rabljeno, številka stroja/vozila: YAMT63XX9K010xxxx, Leto izdelave: 2019, Prosimo, navedite referenčno številko ob povpraševanju: 21189 Specifikacije:• Letnik: 2019• TÜV veljaven do: 12.06.26• 3 osi• Hidravlične nakladalne rampe• Dolžina platforme: 7,485 m• Lastna masa: 6.656 kg• Dovoljena skupna masa: 31.500 kg• Pripravljen za dostavo Opis:Na prodaj imamo Max Trailer prevoznik strojev letnik 2019 s tremi osmi in hidravličnimi nakladalnimi rampami. Prikolica ima TÜV do 12.06.26 in je po besedah lastnika brezhibna. Pripravljena za dobavo. TÜV: Da EU homologacija do: 12.06.2026 Lastna teža: 6.656 Skupna teža: 31.500 Nosilnost: 24.844 Širina: 255 Dolžina: 1003,5 Model: Maskinhenger Dedpfx Aew Srg Eef Ujkg = Več informacij = Za več informacij se obrnite na ATS Norway.

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, prva registracija: 12/1999, dolžina tovornega prostora: 8.000 mm, širina tovornega prostora: 2.460 mm, skupna širina: 2.550 mm, medosna razdalja: 6.200 mm, barva: črn, Leto izdelave: 1999, Konfiguracija osi Največja obremenitev sprednje osi: 8.000 kg Največja obremenitev zadnje osi: 8.000 kg Teže Lastna masa: 7.080 kg Nosilnost: 8.920 kg Dovoljena skupna masa: 16.000 kg Funkcionalno Znamka nadgradnje: Vogelzang Va-8-8 Višina nakladalne površine: 32 cm Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Poškodbe: nobene Dksdpfx Afouuuhpj Ujg

Stanje: rabljeno, prva registracija: 06/1990, barva: drugo, Leto izdelave: 1990, STARE GUME ZA NIZKONAKLADNE PRIKOLICE. Djdpjxvx Ntjfx Af Uskg

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 01/2022, skupna dolžina: 10.000 mm, skupna širina: 2.550 mm, Leto izdelave: 2022, Dodatne informacije: Dkjdeur T Rdspfx Af Ueg Znamka: MCCAULEY Model: MAC-TLL3-33 Struktura: nizkopodni polpriklopnik (platforma D=8500 / Š=2541 / V=700 mm) Leto: NOVO Vzmetenje: zračno Zavore: bobnaste Dimenzije: D/Š: 10000 mm / 2541 mm Mase: polno/prazno: 30000 kg / 7000 kg = Več informacij = Lastna teža: 7.000 kg Nosilnost: 23.000 kg DGVW: 30.000 kg Za več informacij kontaktirajte Deniss Urmaker

Stanje: novo, številka stroja/vozila: 408ba9a39bbb8087056d6e563, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Dedpfx Afei Ri Daj Uskg Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mudflap Half-shell fenders on 1st and 2nd axle with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles, starting to the rear, approx. 1800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t located laterally in the excavator arm recess in the main chassis, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (Padlock not included) 1 storage box let into the gooseneck in the floor with lid, w=720 mm/ l=520 mm / d=170 mm Extendable width to 3,000 mm (not at the rear bevel) (the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) 70 mm timber planks for widening to 3,000 mm Storage compartment for timber planks under the loading platform Lashing rings low-loader (40 lashing possibilities) 1 pair of lashing rings on gooseneck, each 5 t 9 pairs of lashing mushrooms recessed into the outer frame, top and side, each rated 10 t 2 x in the front on the gooseneck 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each rated 5 t (for lashing strap hooks) 3 additional pairs of folding lashing rings, each rated 10 t 1 x inside beside the main frame at the beginning of the low-bed 1 x on the gooseneck (protruding) 1 x recessed into the floor behind the last axle Drawbar coupling for turntable trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8°, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker equalisation) Wheels and Tyres 235 / 75 R 17.5 manufacturer’s choice Steel rims, twin mounting, factory silver Brake System 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, including connection lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front with connecting cable 1 LED beacon with holder, operated via parking light (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Flooring Gooseneck at front with steel/chequer plate floor Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber decked Hydraulically operated via tractor PTO with restrictor, control located on the left side at the front Hydraulic connection with SVK connector NW 10/3, incl. connecting hose Registration Country/Plates Registration country: Germany 24/7 Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, side white and rear red Warning plate according to ECE – 70 Paintwork Chassis hot-dip galvanized including passivation, 15-year warranty again

Stanje: rabljeno, številka stroja/vozila: SA9TRCM319H17xxxx, Leto izdelave: 2009, Prosimo, navedite referenčno številko ob povpraševanju: 21896 Specifikacije: Dobavljeno z novo EU homologacijo Leto izdelave: 2009 Pnevmatike (glejte slike) Nakladalne rampe Dolžina: 895 cm Širina: 255 cm Medosna razdalja: 136/136 cm Lastna teža: 6.000 kg Največja nosilnost: 19.000 kg Opis: NC prikolica za stroje iz leta 2009 z nakladalnimi rampami. Dobavljeno z novo EU homologacijo. Zavore so bile nedavno obnovljene, rampe pa ojačane. Dobava po dogovoru. TÜV: Ne EU odobreno do: 19.10.2025 Lastna teža: 6000 Skupna teža: 25000 Nosilnost: 19000 Širina: 255 Djdpfjxznptsx Af Uskg Dolžina: 895 Model: BT-24 triosna prikolica za stroje = Dodatne informacije = Za dodatne informacije se obrnite na ATS Norway.

Stanje: rabljeno, prva registracija: 11/2010, barva: drugo, Leto izdelave: 2010, GOODYEAR pnevmatike v dobrem stanju za mega ali nizkopodestni priklopnik. Dkedpfoxvx Iisx Af Ueg

Stanje: novo, številka stroja/vozila: 15431365fe5515297a6a9fb05, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball-bearing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium Full-width rear mud flaps Half-shell mudguards on 1st and 2nd axles with antispray mud flaps behind each axle, antispray mud flaps before and after 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points each 5 t located in the excavator arm recess on the side at the main frame, approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox with shelf insert, W=620/H=360/D=440 mm, can be locked with a padlock (lock not included) 1 storage box recessed into the floor at the gooseneck, with lid, W=720 mm / L=520 mm / D=170 mm Extendable width to 3,000 mm 70 mm timber planks for extension to 3,000 mm Storage compartment for timber planks under the loading platform Dedpfxji Ri A Se Af Uokg Lashing eyes (40 securing options) 1 pair lashing eyes on gooseneck, each 5 t 9 pairs lashing mushrooms integrated on top and side of outer frame, each 10 t 2 x on gooseneck to the front 7 x in the low-bed 6 pairs of lashing holes in the outer frame of the low-bed, each 5 t (for tension belt attachment) 3 pairs of additional folding lashing eyes, each 10 t 1 x inside next to the main frame at the beginning of the low-bed 1 x on gooseneck (protruding) 1 x recessed behind the last axle Trailer towing device turntable Drawbar with tested 50 mm towing eye, towing eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum braked axles Parabolic spring suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) front and rear Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice Steel rims, twin arrangement, factory silver Brake system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 Volt, multi-chamber lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable 1 LED beacon with holder, operated via sidelights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel chequer plate covering Followed by 70 mm softwood floor, wheel arch area with steel chequer plate Rear bevel with 70 mm softwood floor Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Timber overlay Spring-assisted lifting Country of registration / Plates Country of registration: Germany 24/7 service hotline Prepared for double-line licence plate holder Conspicuity marking with reflective strips according to ECE R 048, white at the side and red at the rear Warning panel according to ECE - 70 Coating Frame hot-dip galvanized incl. passivation, 15-year corrosion guarantee Drawbar galvanized or black, as per the manufacturer's choice Loading ramps hot-dip galvanized Attention! Archive pictures shown!

Stanje: rabljeno, številka stroja/vozila: SA92856PTJT11xxxx, Leto izdelave: 2019, Prosimo, navedite referenčno številko ob povpraševanju: 21019 Specifikacije: Letnik: 2019 Dolžina: 812 cm Širina: 255 cm Lastna teža: 4.000 kg Dodew S Sy Sjpfx Af Uokg Skupna teža: 19.000 kg 2 osi Zračne zavore Nakladalne rampe s pomočjo vzmeti Ročne podporne noge Pnevmatike (glejte slike) Parabolično vzmetenje Takoj dobavljivo Opis: McCauley nizkopodni priklopnik za stroje na prodaj. Takoj dobavljivo. TÜV: Ne EU homologacija do: 10.02.2025 Lastna teža: 4000 Model: maskinhenger = Dodatne informacije = Za več informacij se obrnite na ATS Norway.

Stanje: novo, številka stroja/vozila: ebf3f771e96394cd89e56bbb7, skupna masa: 11.800 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Central-axle trailer Fine-grain steel welded construction 6 pairs of lashing eyes screwed into the floor/external frame, each rated at 5 tons 2 additional pairs of lashing eyes screwed into the floor, each rated at 5 tons, in the corners Gear support leg at the front Foldable rear support 2 wheel chocks with holder Steel underrun protection Dkjdpfx Afji Rixro Uog Full-width rear mud flaps Quarter-shell fenders 1 plastic toolbox with shelf, dimensions 620mm (w) / 360mm (h) / 440mm (d), lockable with a padlock (padlock not included) Central-axle trailer towing device Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles and suspension Drum brake axles, manufacturer’s choice Axle/chassis laser alignment to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel/rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and tires 235/75 R 17.5 Manufacturer’s choice Steel rims, factory silver Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Steel/Tread plate floor for high point load capacity Note: Minor floor waviness possible due to welding distortions! Platform length approx. 5,200 mm Rear slope approx. 900 mm Front wall / corner posts 25 mm aluminum hollow profile, height 400 mm Sideboards 25 mm aluminum hollow profile, height 400 mm, foldable and removable Rear wall / rear corner posts 1 pair of steel posts attached to the frame with bracket for ramp locking, entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handle on the ramps Covered with 3 toothed steel rails With gas pressure springs for single-person operation Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame hot-dip galvanized incl. passivation 15-year warranty against rust-through Front wall: aluminum Sideboards: anodized aluminum Loading ramps: hot-dip galvanized Attention! These are archive images.

Stanje: rabljeno, številka stroja/vozila: YY9SE51MX9T01xxxx, Leto izdelave: 2009, Prosimo, navedite referenčno številko ob povpraševanju: 20343 Specifikacije: - Model 2009 - 3 osi - Krmiljenje na 1 osi - Trenjsko krmiljenje na 3 oseh - Pripravljen za uporabo - Takojšnja dobava Opis: Na prodaj imamo Damm SE-51M triosni priklopnik za stroje iz leta 2009 s hidravličnim drogom. Priklopnik ima EU homologacijo do 02.09.26 in je takoj pripravljen za uporabo v proizvodnji. Po navedbah lastnika popolnoma deluje, kot mora. Takojšnja dobava. Dsdpfx Afowgzvys Uokg Tuf: Da EU homologiran do: 02.09.2026 Lastna teža: 9750 kg Skupna teža: 51000 kg Nosilnost: 41250 kg Širina: 255 cm Dolžina: 1360 cm Model: SE-51M 3-osni priklopnik za stroje z hidravličnimi rampami = Dodatne informacije = Za več informacij kontaktirajte ATS Norway.

Stanje: novo, številka stroja/vozila: 535119ca408d3bd5a8e74be51, lastna masa: 6 kg, največja dovoljena obremenitev: 11 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with robust ball bearing slewing ring, storage box integrated into turntable front section Foldable rear support Wheel chocks with holders Aluminum side underrun protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) Extendable widening to 3,000 mm (not in rear taper) (Track width of construction machines or vehicles to be transported must not exceed 2,550 mm external frame width), storage compartment for wood planks centered in the loading area, 70 mm planks for widening to 3,000 mm, Dksdpfxoi Ri N Hs Af Ujg Tie-down eyes low-bed 3 pairs of lashing points integrated in the floor at the front, each rated for 10 t 6 pairs of lashing mushrooms recessed in the top and sides of the external frame, each rated for 10 t 1x after neck area, rest distributed in between, spacing not greater than 1,200 mm 1x rear taper 5 pairs of ring lashing eyes recessed in external frame, each rated for 5 t (instead of stake pockets) Trailer turntable drawbar Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tires 235 / 75 R 17.5 manufacturer's choice Twin steel rims, factory silver Braking System 2-line air brake system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, ABS and ALB, with ABS connector at the front, with connecting cable Attention: The trailer must only be towed by towing vehicles that ensure the effectiveness of ABS! Electric system 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white/red width marker lights at rear 2 white position lights at front 1 rotating beacon with bracket, switchable via parking lights (removable beacon) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm 2 x 7-pin fail-safe connectors at the front, with connecting cable Floor Front area steel floor, then 70 mm softwood floor, wheel arch area with steel/tread plate covering Rear taper with 70 mm softwood floor Low-bed area incl. rear taper 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety below, foldable (prevents lateral slipping, not in conjunction with hydraulic side shift) wooden planking with spring assist Operational Notes A special permit is required for an axle load of 10,000 kg. The permit must be applied for individually in each federal state, and the legislator is not obliged to grant approval for a 20 t gross vehicle weight. Customer's risk. The specified gross weight is technically possible, depending on the cargo the gross weight may not be achievable while observing the permitted axle, support, and kingpin loads. Registration / Plates Registration country: Germany EC type approval acc. to 2007/46 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paintwork Frame DB Nova grey Access ramps hot-dip galvanized Note: Archive images!

Stanje: rabljeno, številka stroja/vozila: SZFNN23208LD0xxxx, Leto izdelave: 2008, Prosimo, navedite referenčno številko ob povpraševanju: 19910 Specifikacije: - 3 osi - Levi nožni pedal S. 1 - Pnevmatske pnevmatike so v redu - Vrtenje na 3 oseh - Hidravlični pogonski most - Omara za orodje - Deli za zabijanje - Dvojni voziščni pasovi - Na voljo takoj Opis: Istrail stroj iz leta 2008. Dvojni hidravlični pogonski mostovi. TÜV: Ne EU odobreno do: 15.05.2025 Lastna teža: 11960 Skupna teža: 48000 Dedpev Iu Dzsfx Af Uekg Nosilnost: 36040 Širina: 255 Dolžina: 1337 = Dodatne informacije = Za dodatne informacije kontaktirajte ATS Norway.

Stanje: novo, številka stroja/vozila: a3b1347da4aa7f31dceb875db, lastna masa: 2 kg, največja dovoljena obremenitev: 9 kg, skupna masa: 11 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Central Axle Trailer Fine-grained steel welded construction 6 pairs of lashing eyes bolted to the outer floor/frame, each rated at 5 tons Gear support leg at the front Foldable rear support 2 wheel chocks with holder Steel underrun protection Full-width rear mudflap Dedpfx Aoi Ri Iljf Uekg Quarter-shell fenders Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & Suspension BPW drum brake axles Axles/chassis laser-measured for reduced tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Factory silver steel rims Braking System Dual-line air brake system Hand spindle parking brake Integral air reservoir 2 interchange-proof coupling heads at the front with connecting pipes to the towing vehicle ABS and ALB, ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side markers 2 white front position lights 2 white/red rear marker lights 2 x 7-pin interchange-proof plugs at the front, with connecting cable Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness possible due to welding distortion! Platform length approx. 5,200 mm Rear tapering approx. 900 mm Front wall / corner posts 25 mm aluminum hollow profile, 320 mm high Side walls 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / corner posts 1 pair of steel stanchions fixed to the frame and with holders for securing the loading ramps, entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps wooden inlay with gas strut for one-person operation Operating Instructions The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable within the permitted axle/support/coupling loads. (Poor driving and tracking may result from incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau, 10-year warranty against rust-through Front wall aluminum Side wall anodized aluminum Loading ramps hot-dip galvanized Note: Archive images!

Stanje: rabljeno, številka stroja/vozila: 1xxxx, Leto izdelave: 1986, Prosimo, navedite referenčno številko ob povpraševanju: 21614 Specifikacije – Prikolica za prevoz strojev: EU homologacija do: 24. 09. 2026 Letnik: 1986 Dodpexq Ddfefx Af Ujkg Pnevmatike (glejte slike) Dolžina: 1.180 cm Širina: 250 cm Medosna razdalja: 535 / 140 cm Lastna masa: 6.440 kg Največja nosilnost: 19.560 kg Opremljena z naletnimi rampami TÜV: Da EU homologacija do: 24. 09. 2026 Lastna masa: 6.440 Skupna masa: 26.000 Nosilnost: 19.560 Širina: 250 Dolžina: 1.180 Model: 1986 Goldhofer prikolica za stroje = Dodatne informacije = Za več informacij kontaktirajte ATS Norway.

Stanje: novo, številka stroja/vozila: 6d88bda3a1ee2464a81b34f36, lastna masa: 4 kg, največja dovoljena obremenitev: 13 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction with a slight central camber, turntable with heavy-duty ball bearing slewing ring, chocks with holders, quarter shell mudguards in front of and behind each axle. Lashing Points Low Loader Over front axle: 2 pairs of ring lashing eyes (each 5 t) at the front on the cranked section Low-bed: 4 pairs of lashing eyes (each 6 t) at the sides of the lowbed 5 pairs of lashing eyes (each 5 t) between the longitudinal beams Drawbar Assembly Turntable Trailer Drawbar with certified 40 mm towing eye, mechanically adjustable in length by 6 x 100 mm increments and lockable (Drawbar length 1,700 – 2,300 mm) Axles + Suspension BPW drum brake axles with 10 t axle load each, slack adjusters. Continuous axle brake test up to 105 km/h. Rear axle can be removed manually. To do so, release air locking mechanism, lower the rear section to the ground, disconnect hydraulic hoses from rear section, insert the transport bar into a rear socket, and by gently pushing down and simultaneously pulling backwards, release rear section (parking brake released). After loading/unloading, move rear section into position and hook up to mark. Then raise rear section to driving height and connect hydraulic hoses. Confirm bolt locking (visual inspection if bolt snaps in) and check rear function. Air suspension with lift & lower valve. Wheels and Tires Dkjdpfx Aji Ri N Aof Usg 235/75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver. Braking System 2-line compressed air brake system, spring-loaded parking brake, 2 fool-proof coupling heads at front with connection lines to tractor, EBS, electronic brake system with EBS plug at front with connection cable. Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 volt, multi-chamber lights, yellow LED side marker lights, 2 white position lights front, 2 white/red lane control lights rear, revolving beacon with bracket, powered via parking light (removable), 2 pairs of warning boards double LED illuminated and extendable up to 3,300 mm, removable with plug, 2 x 7-pin fool-proof plugs at front with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (for electrics only, not for ABS/EBS) Floor Steel/aluminum checker plate floor on cranked section, between longitudinal and cross beams with perforated cover plates. Axle cover not drive-over, widening to 3,000 or 3,300 mm possible. Operating Instructions Note! For 10,000 kg axle load, a special permit is required. Permit must be applied for separately in each federal state; the legislator is not obliged to grant approval for 20 t GVW. Customer’s risk. Special permit required if total train length exceeds 18,750 mm. Observe country-specific registration regulations. The stated gross weight is technically possible; depending on the cargo, the gross weight may not be achievable in compliance with permissible axle, support, and fifth wheel loads. Observe BO-circle!!! Registration / License Plates Registration country: Germany, with Dekra inspection and report (per §13 EC-FGV), prepared for single-line license plate holder, ECE-70-compliant warning board, contour marking with reflective strips per ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL black Attention: Archive images!

Stanje: rabljeno, številka stroja/vozila: SKBS40B30JKE2xxxx, Leto izdelave: 2019, Prosimo, navedite referenčno številko na zahtevo: 21327 Specifikacije: Z novo EU homologacijo Leto izdelave: 2019 Pnevmatike (glejte slike) Nove nakladalne rampe Dolžina: 1400 cm Širina: 255 cm Medosna razdalja: 136 / 136 cm Lastna teža: 10.130 kg Dkedpfoxctfcox Af Usg Največja nosilnost: 34.870 kg Opis: Kel-Berg polpriklopnik za stroje s hidravličnimi nakladalnimi rampami. Prikolica se dobavi z novo EU homologacijo. Brez krmiljenja na zadnji osi. Takoj dobavljivo. Lastna teža: 10.130 Skupna teža: 45.000 Nosilnost: 34.870 Širina: 255 Dolžina: 1400 Model: Maskinsemi = Dodatne informacije = Za več informacij se obrnite na ATS Norway.

Stanje: novo, številka stroja/vozila: 2b58968e34fac93b429a256e9, lastna masa: 5 kg, največja dovoljena obremenitev: 12 kg, skupna masa: 18 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-bed trailer Steel welded construction Turntable with robust ball-bearing slewing ring, storage box integrated into turntable front section Rear folding support Wheel chocks with holder Aluminum side underrun protection Full-width rear mud flaps Quarter-shell fenders in front of 1st axle Spare wheel holder for 1 spare wheel, including wheel mounting kit Spare wheel, same brand and specification as standard tires, steel rim Plastic tool box with shelf, w=620/h=360/d=440 mm, lockable with padlock (padlock not included) Lashing rings low-loader 3 pairs of lashing points (10 t each) integrated in front floor, 6 pairs of mushroom lashing points (10 t each) fitted on and into the outer frame at the top and sides: 1x at gooseneck, remaining distributed in between (distance max. 1200 mm), 1x on rear slope 5 pairs of recessed ring lashing points in the outer frame (5 t each, convertible to stake pockets) Drawbar equipment trailer turntable Drawbar with certified 40 mm towing eye Axles and suspension SAF drum brake axles Axle/chassis laser alignment for reduced tire wear and improved fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings Wheels and tires 235/75 R17.5 Manufacturer's choice Steel twin wheels, factory silver Braking system 2-line compressed air braking system Dksdpfx Aei Ri Nxjf Uog Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, including connection cable, voltage converter for 12/24 Volt operation Note: Tractor/trailer requires a 7-pin 12 Volt socket! (Electric system with voltage converter required!) Attention: Trailer may only be towed by vehicles that ensure proper ABS functionality! Electrics 24 Volt, multi-chamber lights, yellow LED side lighting 2 white/red width marker lights at rear 2 white position lights at front Additional LED work light at rear, controlled via reversing light 2x 7-pin non-interchangeable plugs at front with connecting cable 1x 7-pin agricultural plug, voltage converter 12/24 Volt (for electrics only, not for ABS/EBS) Floor Steel floor in front section, followed by 70 mm softwood flooring, steel/chequered plate in wheel arch area Rear slope section with 70 mm softwood flooring Low-bed area including rear slope 8,200 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, timber-planked, with spring assist Operating notes Special permit required for 10,000 kg axle load; permit must be obtained separately in each federal state; no guarantee from authorities for 20 t GVW. Customer assumes risk. Country of registration / plates Country: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7-service hotline Prepared for double-line number plate holder Outline marking with reflective tape per ECE R 048, white side and red rear Paintwork Frame DB 7350 Nova grey 10-year corrosion warranty Drawbar galvanized or black, manufacturer's choice Ramps hot-dip galvanized Attention: Archive images!

Stanje: novo, številka stroja/vozila: 2dff0c136c85096f36822a0bb, lastna masa: 7.150 kg, največja dovoljena obremenitev: 16.850 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis - Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring, storage box integrated into turntable front section Foldable rear supports 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflaps Extendable extensions to 3,000 mm (not at the rear bevel) (Note: The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Central storage compartment for timber boards on the loading platform 70 mm timber boards for extension to 3,000 mm Low-bed lashing rings 3 pairs of 10 t lashing points integrated into the front floor 6 pairs of 10 t lashing mushrooms recessed in the top and side of the outer frame 1 x by the neck area The remaining points are distributed at no more than 1200 mm intervals 1 x at the rear bevel 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (can be converted to 5 t ring lashing eyes, not included) Drawbar Turntable Trailer Coupling Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bearings and mechanical Axle load equalisation (rocker balancing) Brake System 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake included 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: The trailer may only be towed by vehicles ensuring the proper function of ABS! Wheels and Tyres 235/75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver finish Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 LED beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, followed by 70 mm softwood flooring; wheel arch covers in steel/chequer plate Rear bevel with 70 mm softwood flooring Low-bed area incl. rear bevel 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered, included With spring assist Operating Notes An exemption permit is required for 10,000 kg axle load—only indivisible loads allowed! The specified total weight is technically achievable, but depending on the load, the permissible total weight may not be reached due to axle/support/kingpin limits. (Poor driving and tracking may result from incorrect load distribution) Country of Registration/Plates Country of registration: Germany With Dekra inspection and appraisal (according to §13 EU-FGV) 24/7 service hotline Prepared for double-line license plate holder Contour marking with reflective stripes per ECE R 048, white to the side, red to the rear Paintwork Frame DB 7350 Novagrau 10-year guarantee against rust-through Drawbar galvanized or black, manufacturer's choice Dedsi Riy Espfx Af Uskg Access ramps hot-dip galvanized Note: Archive images!

Stanje: rabljeno, številka stroja/vozila: 816b3dfbfa1c7d49b7d052bd6, lastna masa: 2.500 kg, največja dovoljena obremenitev: 8.000 kg, skupna masa: 10.500 kg, konfiguracija osi: 2 osi, prva registracija: 07/2022, velikost pnevmatike: 235/75 r17,5, Leto izdelave: 2022, Further information Chassis: Central axle trailer, low-bed Fine-grained steel welded construction, gearbox support foot at the front, telescopic rear support, wheel chocks with holder, steel fenders over both wheels Dedpfx Aoqmc Rasf Ujkg Coupling system: Central axle trailer Drawbar with certified 40 mm towing eye, height-adjustable by spindle, max. adjustment range 250 mm Axles & Suspension Euro axles of our choice, with tapered roller bearings and S-cam brake, axles/chassis laser-aligned to reduce tire wear and fuel consumption, parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker balance) Brake system 2-line compressed air brake system, spring-actuated parking brake, 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Note: The trailer may only be towed by vehicles which ensure the effectiveness of the ABS! Electrics 24 volt, multi-chamber tail lights, yellow LED side marker lights, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 1 x 15-pin plug at the front, with connection cable. Deck TTS Low-mounted steel trough, deck floor made from steel/chequer plate, steel sidewalls solidly welded to the floor, deck length 5,500 mm, trough with Load-Lock profile at the front and sides for lashing strap attachment (8 pieces at the front, 16 pieces on each side) Note: Slight floor warping may occur due to welding distortion! Pair of lashing rings: 1 x at each front corner of the steel trough and 1 x at the rear in the floor, each rated at 5 tons. Additional pair of lashing rings in the floor, each rated at 5 tons. Drive-on ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable, with grip handles on the ramps, wood-clad, with gas struts for single-operator handling Operating notes The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while adhering to the permissible axle, support and saddle loads. (Poor driving and tracking behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany, with Dekra inspection and certificate (according to §13 EG - FGV), prepared for single-line licence plate holder, contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear.

Stanje: novo, številka stroja/vozila: b50cac2c60a813b0968994fa0, lastna masa: 5.700 kg, največja dovoljena obremenitev: 18.300 kg, skupna masa: 24.000 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Full-width rear mudflap Preparation for widening to 3,000 mm (holes in outer frame, not in rear bevel) Low-loader lashing rings 1 pair of lashing cutouts embedded in the front longitudinal beam at the gooseneck, each rated for 10 t 7 pairs of lashing mushroom pins embedded on top and side of the outer frame, each rated for 10 t 1 x on the front gooseneck 5 x in the low-bed area 1 x in the rear bevel 12 pairs of lashing holes in the outer frame, each rated for 5 t (for lashing strap hooks) 5 x at the gooseneck, 6 x in the low-bed area, and 1 x in the rear bevel Drawbar system for turntable trailer Drawbar with certified 40 mm towing eye Axles & Suspension Drum brake axles, brand as per manufacturer’s choice Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Brake System 2-line air brake system Spring-loaded parking brake 2 unmistakable coupling heads at the front, with connecting lines to the truck, Connecting lines extended by approx. 60 cm Dodpfx Aji Ri Agof Ujkg No ABS, but with mechanical ALB (automatic load-dependent brake valve), thus maximum 60 km/h permit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 7-pin 12 Volt plug at the front with connecting cable, extended by approx. 60 cm 1 LED beacon with holder, operated via parking light (lamp removable) 2 pairs of illuminated and extendable warning plates up to 3,000 mm Floor Front gooseneck with steel/chequer plate covering Toolbox recessed in the drive-over slant to gooseneck Following area with 70 mm softwood floor, wheel arch area with steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-bed loading area including rear bevel: 5,900 mm Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wooden covering Spring-assisted lifting Operating Instructions For axle loads of 10,000 kg, an exemption permit is required; only indivisible loads permitted!!! The stated total weight is technically possible; depending on the load, the total weight may not be achievable within the allowable axle/support and fifth wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate for max. 60 km/h approval, towing vehicle as agricultural/forestry vehicle (LoF), (for Switzerland, max. 40 km/h possible) Prepared for double-line license plate holder No contour markings / reflective tape according to ECE R 048 Painting Frame: DB 7350 Novagrau 10-year corrosion protection warranty Drawbar galvanized or black, according to manufacturer’s choice Loading ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: ede0610378cbe39cc4883251d, lastna masa: 24.000 kg, največja dovoljena obremenitev: 7.550 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further information Chassis Low-loader Trailer Steel welded construction 1st pair of wheel recesses embedded in the driving lane area after the steel platform, bevelled for entry, approx. 1,400 mm long at the bottom, approx. 400 mm deep. Note! Djdpsi Ri Ryjfx Af Uskg Frame is 400 mm higher in the main beam area than at the wheel recess. If machines are to be transported where overall height must be verified, we request a technical data sheet for the machine types with precise specifications (if overall height is exceeded -> customer is responsible, approval required). Depending on ground clearance under the machines, inserts for the wheel recesses may be required on the customer side. Turntable with robust ball race ring, storage box integrated in the turntable front section Rear supports foldable 2 wheel chocks with holder Aluminium side underrun protection Full-width rear mudflap Extending wideners to 3,000 mm (not in rear bevel area) (The track width of the construction machines or vehicles to be transported must not exceed the outside frame width of 2,550 mm) Central storage compartment for wooden planks on loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes low-loader 3 pairs of 10 t lashing points integrated in the floor at the front incl. 6 pairs of lashing mushrooms recessed on top and at the side in the outer frame, each 10 t 1 x at the gooseneck The remaining distributed between, spacing not greater than 1,200 mm 1 x rear bevel 5 pairs of stake pockets integrated into the outer frame, internal 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Drawbar assembly trailer turntable Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum-braked axles Axles/chassis laser aligned to reduce tyre and fuel wear Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colour-coded piping for easy service Spring loaded parking brake 2 interchange-proof coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by tractor units which ensure the functionality of ABS! Wheels and tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED illumination 2 white position lights at front 2 white/red track marker lights at rear 2 x 7-pin interchange-proof plugs at front with connecting cable 1 LED beacon with bracket, switched via parking light (removable lamp) 2 pairs of double warning boards, LED-lit and extendable up to 3,000 mm Floor Front area steel floor, incl. Then with 70 mm softwood floor, in wheel arch area steel/chequer plate covering Rear bevel with 70 mm softwood floor Low-loader deck incl. rear bevel 8,200 mm Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring lifting aid Operating instructions For 10,000 kg axle load, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achievable while complying with permissible axle/kingpin/saddle loads. (Poor driving and tracking behaviour possible due to incorrect load distribution) Country of registration / Plates Country of registration: Germany incl. With Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for two-line number pla

Stanje: novo, številka stroja/vozila: dd98a7658922be8f2e25bcadb, lastna masa: 2 kg, največja dovoljena obremenitev: 8 kg, skupna masa: 10 kg, konfiguracija osi: 2 osi, velikost pnevmatike: 235/75 r 17,5, Further information Chassis Central Axle Trailer Low-bed Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support 2 wheel chocks with holders Steel mudguards over both wheels Central axle trailer coupling equipment Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 250 mm Axles & Suspension Euro-axles (manufacturer’s choice), with tapered roller bearings and S-cam brakes Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5 (manufacturer’s choice) Dkjdji Ri Ebspfx Af Usg Factory silver steel rims Braking System 2-line compressed air braking system Spring-loaded parking brake 2 mistake-proof coupling heads at the front, with connection lines to the towing vehicle, ABS and ALB, with ABS plug at the front, including connection cable Note: The trailer may only be towed by vehicles that ensure proper ABS function! Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white marker lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin mistake-proof plugs at the front, including connection cable Body TTS Low-mounted steel trough, bridge floor made of steel/chequer plate covering, steel sidewalls solidly welded to the floor Bridge length 4500 mm; trough at the front and sides with load-lock profile for attaching lashing straps (8 points in front, 12 per side) Note: Slight floor waviness possible due to welding distortion! 2 pairs of lashing rings, one at the corners of the steel trough front and one at the rear floor, each rated 5t 2 additional pairs of lashing rings in the floor, each rated 5t Ramps Steel ramps, 2300 mm long, 510 mm wide, laterally adjustable, with hand grip on the ramps Wooden covering Gas spring assist for one-man operation Operating instructions The stated gross weight is technically possible; depending on the load, the gross weight may not be achievable while observing the permissible axle/load and saddle loads. (Poor driving and tracking performance possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Outline markings with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame RAL 3002 Carmine red Ramps hot-dip galvanized Note: Archive images!

Stanje: novo, številka stroja/vozila: 195f80ad09517628522e33a91, lastna masa: 7.300 kg, največja dovoljena obremenitev: 16.700 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, velikost pnevmatike: 235 / 75 r 17,5, Further Information Dkodji Ri Rvepfx Af Ujg Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Rear mudflaps across the entire width Quarter shell fenders in front of 1st axle 1st pair of wheel recesses embedded after the kink in the loading bed area, ramped entry, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! The frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses embedded between the axles in the loading bed area, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The frame in the main beam area is 300 mm higher than the wheel recess. Sliding extensions for widening, extendable to 3,000 mm (not in tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Sliding extensions for widening, extendable to 3,000 mm, also at the bottom in the wheel recesses, foldable at the wheel recess extensions (extension not in the tail ramp area) (The track width of the construction machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) 70 mm timber planks for extension to 3,000 mm Tie-down points on low loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front in the kink, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for attaching tie-down straps) 7 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated at 10 t 1x at the front in the kink 6x in the loading bed First lashing point 250 mm from the front and last max. 250 mm from the rear, spacing between lashing points no greater than 1,100 mm Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Axles & suspension SAF drum brake axles Laser axle/chassis alignment – reduces tire wear and fuel consumption Parabolic spring suspension with maintenance-free steel-rubber bushings Wheels and tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-applied parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, LED side marker lights, 2 white position lights at the front 2 white/red lane guidance lights at the rear 2 x 7-pin fail-safe connectors at the front, with connection cable, 1 LED rotating beacon with holder, switched via side light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Front kink with steel/checkered plate covering Storage box embedded in the ramp to the kink, then with 70 mm softwood floor, in the wheel arch area with steel/checkered plate covering Tail ramp with 70 mm softwood floor Low loading area including tail ramp: 6,500 mm Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring assist Operating Instructions For 10,000 kg axle load an exemption is required, only indivisible loads allowed! The stated gross weight is technically possible, but depending on the type of load, the gross weight may not be achievable within the pe