Fliegl 3-Achs Plateau Sds 380 Spezial Mega-Z nakup rabljenega (52.633)

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33801013475, lastna masa: 7.180 kg, največja dovoljena obremenitev: 28.820 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, barva: srebrn, Available in multiple units. Fine-grain steel welded construction, saddle plate with replaceable 2" kingpin, additional splash guard made from sheet metal riveted to the underside floor, in the gooseneck area above the rear axle of the tractor unit as well as above the wheels on the vehicle. Reinforced frame version for vehicle loads up to the outer frame. Outer frame equipped with "Load-Lock profile" approx. every 400 mm for lashing strap attachment, 10 pairs of lashing mushrooms recessed into the outer frame, each rated at 10 tons, 24 ton 2-speed landing gear, single-sided operation, with semi-rounded lower section and straight connection plate, featuring load compensation, foldable rear support, wheel chocks with holder, aluminum side underrun protection, steel underrun protection, quarter-fender mudguards in front of and behind each axle, with additional sheet splash guards over the wheels, fitted with anti-spray mud flaps according to EC standards, 1 plastic toolbox (600 x 425 x 460 mm), lockable. Container locks: 4 pairs of locking recesses embedded in the floor for 2 x 20-foot or 1 x 40-foot container, 4 pairs of container locking adapters (additional cross supports at the front and rear of the container required; the container must be evenly supported across the width; cross supports not included). Ramp attachment bar at rear extension across full width, mechanical rear extension with hand crank extendable by approx. 1,500 mm, lockable every 500 mm, includes extendable underrun protection with lighting. Lane area fitted with Lohr perforated sheet, central area with steel checker plate, storage space for drive-on ramps integrated in rear extension—usable only when rear extension is extended by approximately 1000 mm. For ramp transport with retracted rear extension, ramp storage is located on the right in front of the axles. One pair of ramps, 3,000 mm long, 300 mm wide, load capacity per pair 6,000 kg. Electric cable winch, 24 volts, pulling force approx. 8,165 kg, centrally mounted at the very front, operated by remote control, cable length 35 m x approx. 10 mm, with roller cable window and removable guide rollers. Axles & Suspension: SAF or BPW drum-braked axles as selected by the manufacturer, air suspension, first axle with automatic lift axle, additionally electrically operable from the truck, including forced lowering and drive assist. Brake system: 2-line compressed air brake system, color-coded line routing for easy service, spring-loaded parking brake, 2 fail-safe coupling heads at the front, EBS (electronic braking system) with EBS socket at the front (no connection cable provided), with raise & lower valve and fast venting, hold function in lowered position + auto-reset function, vehicle stability system, axle load detection via EBS CAN bus signal. Ledpfeza Aiyex Adgshi Wheels & Tires: 235 / 75 R 17.5" — brand per manufacturer's choice, twin-mounted steel rims. Electrics: 24 volts, LED multi-chamber lights, side yellow LED lighting, license plate lighting in LED, 2 white position lights at the front in LED, 2 white/red lane marker lights at the rear in LED, 2 x 7-pin and 1 x 15-pin fail-safe sockets at the front, 2 additional LED work lights at the rear, 1 rotating beacon with holder, operated via parking light, 2 pairs of double LED-illuminated warning panels extendable to 3,000 mm, 1 additional 7-pin socket (ISO 1724) in the rear underrun protection, 2 side LED work lights (1 each on front left and right). Floor: Lohr perforated stee

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33801012811, lastna masa: 6.350 kg, največja dovoljena obremenitev: 28.650 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 435/50 R19,5", stanje pnevmatik: 100 odstotek, barva: srebrn, multiple units available Chassis fifth wheel forwarding: Fine-grain steel welded construction, fifth wheel plate with replaceable 2" king pin, reinforced frame for vehicle loading, outer frame with "Load-Lock profile" every approx. 400 mm for lashing strap hooks, 10 pairs of lashing mushrooms recessed on top/outside of the outer frame, each rated at 10 t, foldable rear support, 2 wheel chocks with holders, aluminum side underrun protection, galvanized steel rear underrun protection, quarter mudguards in front of 1st axle and behind each axle, with anti-spray flaps behind each axle, 1 spare wheel holder for 1 single wheel, incl. wheel mounting kit, 2 lockable plastic toolboxes, w=600 / h=425 / d=460 mm, container locks: 4 pairs of locks recessed in the floor for 2 x 20 ft or 1 x 40 ft container, front-most position is a recessed fold-down lock, 10 pairs of stanchion pockets recessed in the outer frame, 70 x 40 mm internal dimension, 10 stanchion pockets recessed centrally in the floor, 70 x 40 mm internal dimension, 2 cross tie-down/stanchion rails recessed into the floor spanning the full width to the outer frame (approx. max usable interior width between external stake pockets 2170 mm), about 100 mm high. Includes 20 mm round steel rails at top and bottom, spacing about 60 mm (between rails); bottom end with angled sheet as closure, open downwards halfway. For lashing and inserting stakes up to 80 x 80 mm. Arrangement: Positions 2 and 4 according to Fliegl data sheet, 20 removable stakes, hot-dip galvanized, storage space for aluminium drive-on ramps, ramps can be inserted from the rear, 3 pairs of fold-down lashing points (10 t) in outer frame (1x in front of front wall and 2x at the rear) Lhedpfeza Agrex Adgji Axles & Suspension: SAF disc brake axles, air suspension, 1st axle with automatic lift axle, includes forced lowering and start assist, actuated by "brake 3x", axle lift below recommended driving height, therefore no warranty for tire damage Brake system: 2-line compressed air brake system, color-coded routing for easy service, spring-type parking brake, 2 fail-safe coupling heads at front, no connecting line, EBS, electronic braking system with EBS socket at front, no connection cable, with raise & lower valve, 2 driving heights adjustable via manual knob: 1x for coupling height 980 mm, 1x for coupling height 1100 mm, ride height in combination with lift axle; when lift axle is raised, load/overall height increases by 50 mm, vehicle stability control system Wheels and tires: 435/50 R19.5, brand at manufacturer's discretion, steel rims Electrics: 24V, multi-chamber lights, yellow LED side lighting, 2 white LED position lights at the front, 2 white/red lane marker lights at the rear, 2 x 7-pin and 1 x 15-pin fail-safe sockets at the front, LED work lights: 1x each left/right in front frame, 2 additional LED work lights at rear, 1 rotating beacon with holder, switched via parking lights, 2 pairs of warning panels: LED-illuminated and extendable to 4,000 mm, additional 7-pin socket at rear underrun protection Floor: phenolic plywood, approx. 30 mm thick, on longitudinal beams for high point loading, suitable for forklift axle load up to max. 7,100 kg Front wall / corner stanchions: 25 mm aluminum hollow section, 1,350 mm high, steel corner stanchions in volume version, front wall inside also lined with 1,250 mm phenolic plywood, "Crash-Blocker", lower 140 mm inside with steel impact protection, storage compartment for insertable stanchions insi

Stanje: rabljeno, lastna masa: 8.430 kg, konfiguracija osi: 3 osi, prva registracija: 11/2023, naslednji pregled (TÜV): 11/2026, velikost pnevmatike: 235/75 R17.5-235/75 R17.5, Leto izdelave: 2023, številka: 54781 Oprema: * Stranski zaščitni elementi, * Orodjarna omara: 4, * Izvedba zadnjih vrat: zadnja portalna vrata, * Zaklepne palice na zadnjih vratih: 4, * Pomikajoča se nadkrita, * Stranska pomikajoča se ponjava, * Dvigni se strop, * Tlačna plošča: tla iz vezanice, Lhsdpezmivxjfx Adgei * Vstavna letva (aluminij): 40, * Zračna priključna točka: ostalo: rumena/rdeča + Duomatic, * Električna priključna točka: 1 x 15-polna + 2 x 7-polna, * ABS, * EBS VIN: WFDFLT33901013129 Dimenzija pnevmatik: 235/75 R17.5 Dolžina (notranja): 14,8 m Širina: 2,55 m Širina (notranja): 2,46 m Višina: 4 m Višina (notranja): 3 m

Stanje: novo, konfiguracija osi: 3 osi, barva: sivo-črna, vrsta prenosa: mehanski, Colour: Natural, lift axle, electronic braking system (EBS), 1x 15-pin connection plug. Equipment: Slightly beveled new-design outer frame with “Load-Lock Profile” for lashing straps, 13 additional pairs of lashing rings in the outer frame, each rated 5 t for a total of 24 t. Two-speed landing gear, single-sided operation, with semi-circular lower section and straight forklift underrun protection made of steel on the outer frame (sides and rear). One spare wheel carrier for one single wheel, with wheel fastening kit. 1 plastic toolbox (650 mm x 520 mm x 670 mm). 7 pairs of drop-in stake pockets (83 x 83 mm) integrated into the outer frame. SAF disc brake axles with 430 mm air suspension. First axle is an automatic lift axle, including forced lowering and starting aid, activated with third brake circuit. Wheels and tires: 6 x 385/65 R22.5, brand manufacturer; 6 steel rims, factory silver. Flooring: approx. 30 mm phenolic plywood, cross joints with Omega insert for high point loading, forklift axle load up to max. 7,100 kg. Front wall / corner posts: 25 mm aluminium hollow profile, 1,950 mm high; steel corner posts in high-volume version plus 2 center supports as “Crash Blocker” (mounted inside lower area at approx. 140 mm). Sideboards: 25 mm aluminium hollow profile, 700 mm high. Paintwork: chassis hot-dip galvanized including passivation ("15-year anti-corrosion warranty"). Aluminium sideboards anodized. Subject to errors and changes. Lhedpotcwmisfx Adgsi

Stanje: rabljeno, Funkcionalnost: omejena funkcionalnost, lastna masa: 6.575 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dovoljena osna obremenitev (os 1): 9.000 kg, dovoljena osna obremenitev (os 2): 9.000 kg, dovoljena osna obremenitev (os 3): 9.000 kg, prva registracija: 07/2011, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 1.300 mm, skupna dolžina: 13.650 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 385/65R22,5, stanje pnevmatik: 30 odstotek, medosna razdalja: 1.360 mm, Leto izdelave: 2011, Oprema: ABS, Rabljen odprt polpriklopnik Jeklena sprednja stena z izbočenjem za dolge jeklene profile Tla okrepljena z jeklenimi profili Lhodpfxsy Ercbo Adgsi Stranski žepki za stebričke Skladiščna škatla za vstavljive stebričke

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33901014232, lastna masa: 5.900 kg, največja dovoljena obremenitev: 29.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2025, dolžina tovornega prostora: 13.650 mm, višina nakladalnega prostora: 900 mm, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, skupna višina: 2.638 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", barva: srebrn, The images are archive photos! The vehicle may still be in use! Chassis: Semitrailer for Freight Forwarding Fine-grained steel welded construction, fifth wheel plate with interchangeable 2" king pin Drive-over and suitable for use with construction/agricultural machinery up to max. 24,000 kg GVW and up to a maximum machinery width of 2480 mm (the track width of machines or vehicles to be transported must not exceed 2200 mm), hook-in bar for aluminium ramps at the rear (wider construction/agricultural machinery must not be loaded) Outer frame in new slightly angled design with "Load-Lock Profile" for lashing strap attachment 14 pairs of recessed lashing rings in the outer frame, each rated at 2.5 t 6 pairs of recessed lashing rings in the outer frame, each rated at 5 t 24 t, 2-speed landing gear, single-sided operation, with straight base, without crossbar equalizer Free landing gear foot dimension or free swing radius to the rear approx. 1920 mm Rear support foldable 2x wheel chocks with holder Side underrun protection aluminium Rear underrun protection steel Quarter mudguards in front of and behind each axle With anti-spray splash guards behind each axle 1x spare wheel holder for 1 spare wheel, with fixing kit 1x spare wheel, same make as standard tires, steel rim Axles + Suspension SAF drum brake axles "Axle/chassis laser alignment" - reduces tire wear and fuel consumption Air suspension 1st axle is an automatic lift axle, additionally electronically controllable from the truck, incl. forced lowering and starting aid, no installation required on the truck (starting aid functions up to an axle overload of 30% and up to a speed of max. 25 km/h) Braking System 2-line compressed air braking system Color-coded piping for easy maintenance Spring-actuated parking brake 2 foolproof coupling heads front, without connecting line 24 Volt EBS, Electronic Braking System with EBS socket at the front, without connecting cable Important: The drawbar trailer may only be towed by tractor units that ensure the effectiveness of ABS! With lift & lower valve Vehicle - Driving Stability System "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via tractor unit's screen via EBS, no truck installation (requirement must be met by the tractor unit. Only for standard tires) Wheels and Tires Ledpfx Adsxb D Swjgshi 235/75 R17.5 twin tires Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side amber LED lighting Side amber LED lighting connected to indicators "flashing side markers" 2 white LED position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin foolproof sockets at the front, without connecting cable Floor Phenolic plywood panels approx. 30 mm thick, for high point load capacity, forklift axle load up to max. 5,600 kg Front wall / Front corner posts 25 mm aluminium hollow profile, 1,350 mm high, corner stanchions steel, volume design Front wall additionally covered on inside with 1,250 mm high phenolic plywood panel Frame hot-dip galvanised The images are archive photos! The vehicle may still be in use!

Stanje: novo, največja dovoljena obremenitev: 25.050 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.500 mm, višina nakladalnega prostora: 950 mm, skupna širina: 2.550 mm, Skupna masa: 35.000 kg / 48.000 kg Lastna masa: 9.950 kg Nosilnost: 25.050 kg / 38.050 kg Skupna dolžina: 21.000 mm Dolžina nakladalne površine: notranja dolžina ca. 13.500 mm / največja dolžina nakladalne površine 21.000 mm Širina: 2.550 mm Višina nakladalne površine: 950 mm Dodatne informacije Novo vozilo iz tekoče proizvodnje, kmalu na voljo Teleskopska zadnja podpora 4 zagozde za podlaganje koles z nosilcem 4 para spuščajočih kontejnerskih zapor v dnu za 1x 40 ft. kontejner ali 2x 20 ft. kontejnerja 1 nosilec rezervnega kolesa za 1 rezervno kolo, z garnituro za pritrditev, v košarici 11 parov žepov za stranice v zunanjem okvirju, primerni za FR-vložne stranice 80x50 mm, vgrajeni poravnano z zunanjim okvirjem, z odprtino za pritrditev pasu ali verige 20 kosov natakljivih stranic B=80 / G=50 / D=1500 mm 1 plastična orodjarna 3 para priveznih ušes po 3,5 t, vgrajenih v stranski okvir – v predelu vratu 13 parov zložljivih priveznih obročev po 10.000 daN, prostoviseče obešenih v profilu stranskega okvirja (primerni tudi za prekomerno široko privezovanje) 1 par zložljivih priveznih obročev po 10.000 daN, vgrajenih ob strani na vmesni podpori Lhsdpfxsumha Nj Adgoi Zračno vzmetenje z možnostjo dviga in spuščanja 1. os samodejna dvižna os, dodatno prisilno spuščanje, vključno s pripomočkom za speljevanje z gumbom za upravljanje na polpriklopniku, brez upravljanja iz kabine voznika z ventilom za dvig in spust + funkcija samodejne ponastavitve Kolesa in pnevmatike 235/75 R 17,5" jekleni platišči v dvojni izvedbi, tovarniško srebrni 24 V, večkomorni žarometi, stranska rumena LED osvetlitev 2 sprednji beli pozicijski LED luči 2 zadnji LED luči za označevanje sledi (belo/rdeče) 2 x 7-polna in 1 x 15-polna varnostna vtičnica spredaj, brez priključnega kabla 2 dodatna LED delovna žarometa zadaj, vklop preko vzratne luči 1 odstranljiva opozorilna luč na zaščiti proti podrsu 1 x 7-polna vtičnica zadaj 6 stranskih vtičnic: 2x sprednja stena, 2x podporna noga, 2x zadnji konec (levo + desno), 7-polni 2 delovna žarometa, zgoraj vgrajena v sprednjo steno, vključno s stikalom 2 para table za označevanje prekomerne širine, vsaka s po 2 LED pozicijski lučki na tablo, stransko raztegljive do 3.500 mm, table dodatno nastavljive na nakladalno površino (prilagoditev širine brezstopenjsko) Fiksna jeklena sprednja stena, višina 1.200 mm, z robustnimi jeklenimi vogalnimi stebri brez poševnine v kotih, stransko ravna izvedba 2 luknji za privez zgoraj noter in zunaj v zgornjih kotih sprednje stene Prednji okvir vroče cinkan + zunanji okvir na vidnem delu končna lakirana v RAL 3002 karminsko rdeči barvi Zadnji okvir vroče cinkan + zunanji okvir na vidnem delu končna lakirana v RAL 3002 karminsko rdeči barvi Sprednja stena RAL 3002 karminsko rdeča

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 6.200 kg, največja dovoljena obremenitev: 32.800 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.000 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, vzmetenje: zrak, velikost pnevmatike: 445/45 R19,5", stanje pnevmatik: 100 odstotek, barva: originalen, Leto izdelave: 2026, Prihranite pri stroških transporta! Po želji dostavimo do tri prikolice za transport zaves, zasnovane za varčno shranjevanje v obliki sklopa treh prikolic. Streha in stranske ponjave so priložene ločeno in se po dostavi enostavno namestijo. Tako boste uživali v znatno nižjih stroških transporta. Rešitev za transport, prilagojena vašim potrebam Konfigurirajte svoje vozilo Fliegl glede na vaše zahteve. Prikazano vozilo je zgolj primer. Proizvodnja in oprema potekata individualno, glede na želje stranke. #Šasi - sedelna prikolica - transport Fine jeklene varjene konstrukcije, z blago prednapetostjo v območju vrat, sedelna plošča z zamenljivim 2-palčnim kraljevskim členkom Zunanji okvir rahlo nagnjen, nova izvedba z "profilom za pritrditev pasov" za pritrditev zategovalnih pasov 24 t, 2-stopenjski dvigalni mehanizem, upravljanje z ene strani Izvlečna lestev na zadnji strani Stranske zaščite Podvozna zaščita, pocinkano jeklo Zaščita na zadnji strani 1 plastični orodjarni kovček, š=600 / v=425 / g=460 mm 1 predal za gasilni aparat do 6 kg #Osi + vzmetenje Osno vzmetenje s kolutnimi zavorami "Osno vzmetenje lasersko merjeno" zmanjšanje obrabe pnevmatik in porabe goriva Zračno vzmetenje 1. os – avtomatska dvižna os, vključno s prisilno spuščanjem in pomočjo pri speljevanju, upravljanje "3-krat pritisnite zavoro" #Zavorna sistem 2-vodni zračni zavorni sistem Barvno označene vodne povezave za enostavno vzdrževanje Zavora s pomnilnikom vzmetne energije 2 varno nameščene sklopke na sprednji strani, brez povezovalnega kabla EBS, elektronski zavorni sistem z vtičnico EBS na sprednji strani z ventilom za dvig in spuščanje Višina vozila v povezavi z dvižno osjo; pri dvignjeni dvižni osi se nosilnost oziroma skupna višina poveča za 50 mm Sistem stabilnosti vozila Lhodpszmub Hofx Adgoi #Kolesa in pnevmatike 445/45 R19,5", jeklena platišča, tovarniška srebrna barva #Elektrika 24 voltov, večkomorne luči, stranska rumena LED osvetlitev 2 beli pozicijski svetili na sprednji strani 2 beli/rdeči markerji na zadnji strani 2 x 7-polni vtičnici na sprednji strani #Tla Plasti iz sitotiska, debeline približno 30 mm, nameščene na vzdolžnih nosilcih za visoko točkovno nosilnost, nosilnost osi viličarja do največ 7100 kg Na zadnji strani jeklena/valovita pločevina, nameščena na dolžini približno 300 mm #Sprednja stena / stranski nosilci na sprednji strani 2580 mm visoka, stranski nosilci iz jekla, robustna izvedba, naprava za odpenjanje stranske ponjave na sprednji steni, "Zavora proti trčenju", na spodnji notranji strani na višini približno 140 mm, jeklena zaščita proti trčenju Sprednja stena je dodatno obložena s plastjo iz sitotiska, visoko 1250 mm #Srednji nosilci 3 pari drsnih nosilcev, drsno nastavljivi po celotni dolžini, s štirimi vstavnimi žepi in na spodnji strani z dolgim žepom 3 pari položajev nosilcev 4 vrste aluminijastih V-vstavnih letvic #Zadnja stena / stranski nosilci na zadnji strani Stranski nosilci na zadnji strani iz jekla do spodnjega roba strehe, pritrdilni elementi za ponjavo z okroglim cevovodom in zategovalnim mehanizmom za ponjavo Zadnja vrata, dvočna z dvema notranjima vrtljivima ključavnicama #Ponjava Ponjava z varjenimi horizontalnimi in vertikalnimi pasovi Zategovalni mehanizmi iz nerjavečega jekla #Streha Drsna ponjava, zadnji del je dvižen, ponjava drsi od zadnje proti sprednji strani, L-strešni okvir za avtomobilsko industrijo Streha neelastična, minimalno upogibanje strešnega okvirja pri nakladanju in razkladanju Optimalna dežna letva na zadnji strani,

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 4.840 kg, največja dovoljena obremenitev: 21.160 kg, skupna masa: 26.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 12.050 mm, širina tovornega prostora: 2.550 mm, skupna dolžina: 12.200 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", Customised transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown serves as an example. Production and equipment are individually tailored to customer specifications. Chassis: Semi-trailer for freight forwarding Fine-grain steel welded construction, fifth-wheel plate with replaceable 2" kingpin, reinforced attachment point for 'gallows' mount and robust wear plates around the area. Rear coupling rail for aluminium ramps. Outer frame: Slightly tapered, new design with 'Load-Lock profile' for lashing strap attachment. 'Patented Load-Lock-Cross' for lashing strap attachment, cross-member beneath the outer frame, 24 t. 2-speed landing gear, single-sided operation, with straight lower section, without compensating cylinder, free landing leg base or free rear swing clearance approx. 1920 mm, without supports, 2 wheel chocks with holders, aluminium side underrun protection, steel rear underrun protection, quarter-round mudguards in front of and behind each axle, without impact guard, spare wheel holder for 1 spare wheel, with wheel fixing kit, spare wheel matching main tyre brand, steel rim. Plastic toolbox with shelf, width=620/height=360/depth=440 mm, lockable with padlock. Axles & Suspension: Drum brake axles, axles/chassis laser-aligned to reduce tyre wear and fuel consumption. Non-steering, air suspension, without lift axle. Brake system: 2-line pneumatic brake system. Colour-coded piping for easier maintenance, spring-loaded parking brake. 2 non-interchangeable coupling heads front, without connecting line, EBS (Electronic Braking System) with EBS socket at the front (no connecting cable). Note: The trailer may only be towed by tractors capable of ensuring ABS efficacy! With raise/lower valve, vehicle stability control. Lsdezb Ikfepfx Adgjhi Wheels & Tyres: 205/65 R17.5, make at manufacturer's discretion, rated for 8 t axle load at 80 km/h, steel rims, factory silver. Electrics: 24 Volt, multi-chamber lights, yellow LEDs on the sides, 2 white position lamps at the front, 2 white/red lane-keeping lamps at the rear, 1 x 15-pin socket front (no connecting cable), LED work lamp in angled section (switched via reversing light), if technically feasible, additional LED work lamp at rear, switched via reversing light. Floor: Anti-slip phenolic plywood panels, approx. 30 mm thick, high point load capacity for forklift axle load up to max. 5600 kg. Front wall / Front corner stanchions: 25 mm aluminium box section, 1,350 mm high, steel corner stanchions in volume design. Customised transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown serves as an example. Production and equipment are individually tailored to customer specifications.

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33902028859, lastna masa: 5.660 kg, največja dovoljena obremenitev: 29.340 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, skupna dolžina: 13.700 mm, skupna širina: 2.550 mm, skupna višina: 3.700 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5", stanje pnevmatik: 100 odstotek, barva: rdeča, Chassis Semi-Trailer for Freight Forwarding Steel welded construction in reinforced design, only two longitudinal beams as double T-beams with steel/checker plate between the beams. Fifth wheel plate with replaceable 2" king pin. Protective cover for rear lights. 8 pairs of lashing rings, bolted or welded to the frame as per manufacturer’s choice. 24 t two-speed landing gear, single-sided operation, with straight base, without compensating leg. Wheel chocks with holders. Side underrun protection in aluminium. Rear underrun protection in galvanized steel. Half-shell mudguards with anti-spray flaps according to EC specifications. 1 spare wheel holder for 1 spare wheel, incl. wheel fixing kit. 1 toolbox recessed between the longitudinal beams. 8 wooden stake pockets, as per manufacturer’s preference, bolted onto the frame, each with 2 telescopic wooden stakes adjustable from 1800 mm to 2800 mm, 7 t per pair. Axles + Suspension BPW disc brake axles with 430 mm disc diameter. Air suspension with lift & lower valve, axle safety cables. First axle with automatic lift, incl. forced lowering and start assist, activated by “3x brake” (start assist functions up to 30% axle overload and up to 25 km/h). Axle spacing offset 1410/1310 mm (suitable for combined transport) up to 44 t gross train weight. Wheels and Tyres 385/65 R 22.5" Manufacturer’s choice. Steel rims, factory silver. Brake System 2-line compressed air brake system. Spring-type parking brake. Axle load detection via EBS CAN-bus signal for display in truck cab (truck must be equipped accordingly, no truck installation, not a verified scale). 2 front coupling heads, non-interchangeable, without connection line. EBS (Electronic Braking System) with front EBS socket, without connecting cable. Note: The trailer may only be towed by tractors that can guarantee ABS effectiveness! “Safe Parking.” Electrical System 24 Volt, multi-chamber tail lights, side LED marker lamps in yellow. 2 white position lamps front. 2 white/red lane-control lamps rear. 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, without connection cables. Front Bulkhead/Corners Steel/mesh bulkhead, approx. 2,300 mm high, bolted to frame. Approval / Signage Ljdpfx Ajza Anvedgehi Registration country: Germany Type approval according to EC 2007/46 Prepared for single-row license plate holder Contour marking with reflective tape per ECE R 048, white on sides, red at rear Warning sign per ECE-70 Paintwork Frame: DB 7350 Novagrau Landing gear legs: black coated Bulkhead: hot-dip galvanized

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 35.400 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.500 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 940 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading area: - Loading deck in extendable design - Loading deck with hardwood planks, rear bevel approx. 500 mm x 8° - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cut-outs in the loading deck's external frame for attaching tension belts Braking system: - Braking system in accordance with EU regulations, with EBS-E (2S2M) Painting: - First-class, durable corrosion protection for the standard shot-blasted welded frame guaranteed by a two-component (2K) zinc-rich primer - High-quality two-component (2K) top coat in solid Novagrey - Rear section metallised and painted in RAL 9010 (pure white) - Metallic paint not available Landing gear: - JOST mechanical landing gear with 2-speed gearbox, 24t lifting capacity (test load 50t) Steel construction: - Steel structure made from high-strength fine grain steels Lsdsl Ux Rwepfx Adgshi - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, LED lighting 24 Volt - Sockets: 2x 7-pin & 15-pin Axles and tyres: - BPW axles, air suspended, with disc brakes (377 mm), with lifting/lowering function - Hydro-mechanically forced steering - Axle tools - Twin tyres 235/75 R 17.5 Accessories included: - Yellow-red air couplings at the galvanised front connection bar - 4 wheel chocks with holder - 2" king pin - Galvanised steel headboard approx. 1600 mm high - White reflective tape on the sides, sliding section and rear in red in accordance with EU regulations - Loading deck with heavy-duty hardwood floor - Rear and front steering by cable - Remote control via push buttons, with single-track monitoring of the axles - With wireless remote control for rear steering - 9 pairs of stake pockets for 100 x 50 mm plug-in stakes on the outer frame of the loading deck - Galvanised folding supports under the loading deck bevel - Sliding mounting rail for aluminium loading ramps at the rear of the vehicle - European reflective panels (red-yellow) at the trailer rear - One mud flap at the trailer rear - Mount for a beacon at the trailer rear - Mounts for warning boards including socket on gooseneck and rear panel, each left and right - Stainless steel toolbox INOX 1,500 x 390 x 810 under the loading deck, right side in driving direction - Central lubrication system BEKAMAX (Pico) with NLHI-2 multipurpose grease and removable protection around pump - 6 pairs of WADER container locks on the loading deck for 1x 20ft, 2x 20ft or 1x 40ft containers, additional locking for one 45ft container in extendable section - 4 pairs of crosswise stake pocket strips mounted in the loading area for 100 x 50 mm plug-in stakes - Lift axle on the first axle, controlled by TEBS, dependent on current axle load and load condition - 80 km/h speed stickers at the rear and on both sides - Four extendable warning boards ca. 400 mm (approx. 423 x 423 mm) with LED position light - Beacon mount on the warning boards - Load gauge for axle load determination, including load diagram - HRM metallisation (High Resistance Metallisation) on the external frame - Complete steel construction shot-blasted, then all defined visible areas metallised with ZINACOR 850 (85% zinc, 15% aluminium) by thermal spraying

Stanje: novo, lastna masa: 10.000 kg, največja dovoljena obremenitev: 41.600 kg, skupna masa: 51.600 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Loading Platform: - Gooseneck, length approx. 4,100 mm with central beam - Extendable loading platform, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated hook-on bar for attaching loose ALU approach ramps - Pneumatic locking system with conical locking bolts and reinforced locking positions - Supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles, Suspension, and Tyres: - BPW axles and suspension, all axles hydro-mechanically forced steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tyres 235/75 R17.5, twin-mounted Paintwork: - 6-coat surface treatment - Complete steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paintwork with 2 layers of 2-component (acrylic) paint, single colour in MB 7350 Novagrau, followed by cavity sealing with special wax Steel Structure: - Steel structure made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket at the front connection strip - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck Lhsdpfxjiuy Nle Adgsi - 4 pairs of stake pockets integrated into the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 transverse stake pocket strip mounted in the floor of the gooseneck for stakes approx. 100x50 mm (1x rear on gooseneck) - 2'' kingpin - Mechanical landing legs with 2-speed gearbox and hand crank - JOST Module B – static test load = 50,000 kg - On the gooseneck and loading area, approx. 32 mm wooden flooring in ALU-omega profiles - One locking position on the extension, approx. every 500 mm - 10 pairs of recessed folding lashing rings in the outer frame of the loading area, folding outwards - 6 pairs of stake pockets integrated into the outer frame of the loading area for stakes approx. 100x50 mm - 2 transverse stake pocket strips mounted in the floor of the loading area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Tapered end crossmember of the vehicle, approx. 350 mm 10° - Integrated hook-on bar for loose ALU approach ramps at the rear crossmember of the vehicle - 1 pair of drop tube supports at the rear crossmember - Mudguards on all axles - Central lubrication system with 1 pump - Remote steering from front and rear operable via cable remote control with push button, including single-track monitoring of the axles - Under the gooseneck and at the rear crossmember, left and right, each with a 7-pin socket for warning panels - One 7-pin socket at the rear crossmember - Container locks "TWIST-LOCKS" in the loading area for transport of 2x 20ft and 1x 40ft containers - Radio remote control for rear steering in addition to cable remote control, with 2 indicator lights on the receiver for single-track monitoring - 2 axle load gauges + axle load diagram - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible areas hot-coated in metallic finish using ZIN

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 5 kg, največja dovoljena obremenitev: 29 kg, skupna masa: 35 kg, konfiguracija osi: 3 osi, skupna dolžina: 13.990 mm, skupna širina: 2.550 mm, velikost pnevmatike: 385 / 65 r 22,5, stanje pnevmatik: 100 odstotek, Rešitev za transport po meri Konfigurirajte svoje vozilo Fliegl glede na vaše zahteve. Prikazano vozilo je primer. Proizvodnja in oprema se izvedeta individualno po željah stranke. Dodatne informacije Podvozje polpriklopnik za špedicijo Jeklena varjena konstrukcija v ojačani izvedbi, le 2 vzdolžna nosilca kot dvotirna nosilca z jekleno/rebrasto pločevino med nosilcema, sedelna plošča z izmenljivim 2. kraljevim zatičem. Zaščitni pokrov za zadnje luči. 1 jeklen zabojnik, vgrajen med vzdolžnima nosilcema 8 parov pritrdilnih ušes na okvirju, vijačeno ali varjeno po izbiri proizvajalca 24 t, 2-stopenjska podporna noga, enostransko upravljanje, z ravnim spodnjim delom, brez kompenzacije potiska 2 zagozdi z nosilcem Stranska zaščita proti naletu iz aluminija Podvozna zaščita iz pocinkanega jekla Polovični blatniki z antispraj ščitniki v skladu z EU 1 nosilec za rezervno kolo za 1 E-kolo z kompletom za pritrditev kolesa 8 lesenih nosilcev po izbiri proizvajalca, privijačenih na okvir, vsak z 2 teleskopski leseni prečki, raztegljivi od 1800 do 2800 mm, nosilnost para 7 t Premi in vzmetenje SAF premne z disk zavorami, 430 mm Zračno vzmetenje z dvigalom in spuščanjem, varovalna vrv na oseh 1. os avtomatsko dvižna, vključno s prisilnim spustom in pomočjo pri speljevanju, aktivacija s 3 × zaviranjem (pomoč pri speljevanju deluje do 30 % prekoračitve osne obremenitve in največ do 25 km/h) Pomak osnega razmika mm (kombinirani promet) do skupne teže vlečne kompozicije 44 t Kolesa in pnevmatike 385 / 65 R 22,5 po izbiri proizvajalca Lhedpsi Rivwsfx Adgoi Jeklena platišča, tovarniško srebrna Zavorni sistem Dvovodni zračni zavorni sistem Parkirna zavora z vzmetnim akumulatorjem Prepoznavanje obremenitve osi preko EBS-Canbus signala za prikaz na zaslonu v kabini, tovornjak mora biti ustrezno pripravljen, brez namestitve na tovornjak (ni overjene tehtnice) 2 varnostni sprednji spojni glavi brez spojne cevi EBS – elektronski zavorni sistem z EBS vtičnico spredaj, brez priključnega kabla Pozor: Prikolico smejo vleči samo vlečna vozila, ki zagotavljajo delovanje ABS! Električna oprema 24 V, večkomorni žarometi, stranske rumene LED luči 2 beli pozicijski luči spredaj 2 belo/rdeči marker luči zadaj 2 × 7-polni in 1 × 15-polni varni vtičnici spredaj, brez priključnih kablov Sprednja stena/ vogalni nosilci spredaj Sprednja stena iz jekla/mreže, cca 2300 mm visoka, privijačena na okvir Homologacija/tablice Država homologacije: Nemčija Potrdilo skladnosti po EG 2007/46 pripravljeno za enovrstni nosilec registrske tablice Obrobljanje s reflektivnim trakom v skladu z ECE R 048, stranski beli, zadaj rdeči Lakiranje Okvir DB 7350 novosivo Podporne noge črno prevlečene Sprednja stena vroče cinkana Pozor: Arhivske fotografije! Rešitev za transport po meri Konfigurirajte svoje vozilo Fliegl glede na vaše zahteve. Prikazano vozilo je primer. Proizvodnja in oprema se izvedeta individualno po željah stranke.

Stanje: rabljeno, največja dovoljena obremenitev: 32.700 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, prva registracija: 08/2022, dolžina tovornega prostora: 13.600 mm, širina tovornega prostora: 2.480 mm, skupna širina: 2.550 mm, Skupna teža: 39.000 kg Lastna teža: 6.300 kg Nosilnost: 32.700 kg Skupna dolžina: 13.850 mm Dolžina nakladalnega prostora: 13.650 mm Širina: 2.550 mm Višina nakladanja: ca. 1.100 mm Dodatne informacije - Notranja višina ca. 2.600 mm - Notranja dolžina ca. 13.650 mm - Notranja širina ca. 2.480 mm - Pnevmatske gume 385/65R22,5 - SAF osi - Zaščita proti podvozu Lhsdpfx Asywq E Sjdgoi - Priprava za viličarja zadaj - Zračno vzmetenje - Zadnja os krmiljena - Drsna streha "Blitz-Verdeck" - Drsni obroči - Vstavljive letvice

Stanje: skoraj kot novo (rabljeno), Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33902036561, lastna masa: 5.820 kg, največja dovoljena obremenitev: 29.180 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 04/2025, naslednji pregled (TÜV): 04/2026, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 2.740 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5", stanje pnevmatik: 90 odstotek, barva: rdeča, Na slikah so arhivske fotografije! Vozilo je po potrebi v uporabi! #Šasi, sedelna prikolica Jeklena konstrukcija iz fino zrnatega jekla, varjena, lahka zasnova, sedelna plošča z zamenljivim 2-palčnim kraljevskim čepom Zunanji okvir, rahlo nagnjen, nova izvedba z "profilom za pritrditev trakov" za pritrditev zategovalnih trakov 3 pari pritrdilnih točk, dodatno vgrajenih v zunanji okvir, po 2,5 tone 14 parov pritrdilnih točk, dodatno vgrajenih v zunanji okvir, po 2,5 tone 24 ton. Dvo-stopenjska oporna vijačna opora, upravljanje z ene strani, z ravnim spodnjim delom, s kompenzacijo potiska Proizvajalec: SAF Opomba: Prosti kot opornih nog oziroma prosti radij gibanja nazaj je približno 1930 mm Lodpoxbzkksfx Adgjhi Izvlečna lestev na zadnji strani Stranski držalo vrat 2 podstavka s držalom Stranski zaščitni okvir iz aluminija barvan v RAL 3002, karminsko rdečo Brez garancije za prevleko/barvanje pri prebarvanih obdelanih dodatnih delih. Podvozni zaščitni okvir, pocinkan jeklo barvan v RAL 9010, čisto belo, tudi držalo podvoznega zaščitnega okvirja Brez garancije za prevleko/barvanje pri prebarvanih obdelanih dodatnih delih. Polovični blatniki spredaj in za osjo z zaščito proti brizganju v skladu z evropskimi predpisi Zadnji zaščitni okvir 1 aluminijasta lestev, približno 2550 mm, z držalom na strani, za stranskim zaščitnim okvirjem Pritrdilna letev na zunanjem okviru za pritrditev direktnih zategovalnih trakov za ponjavo, v vijačni izvedbi, približno 15–20 mm nad tovorno površino, z zgornjim profilom z luknjami za pritrditev zategovalnih trakov 2 plastični orodjarni kovček, š=800/v=450/g=450 mm vsak po 1 na levi in desni strani, za 3. osjo #Osi in vzmetenje BPW osi s kolutnimi zavorami s 430 mm premerom koluta Pestnice, barvane v RAL 3002, karminsko rdečo "Laserjev merski sistem osi/podvozja", zmanjšanje obrabe pnevmatik in porabe goriva Zračno vzmetenje #Zavorni sistem Dvo-vodni zračni zavorni sistem Barvno kodirana vodila za enostavno vzdrževanje. Zavora z vzmetjo 2 varnostna vtičnica spredaj, ki se ne moreta zamenjati, brez povezovalnega kabla 24-voltni EBS sistem, proizvajalec Wabco, elektronski zavorni sistem z EBS vtičnico spredaj, brez povezovalnega kabla Pozor: Prikolico lahko vlečejo samo vlečna vozila, ki zagotavljajo učinkovitost ABS! z ventilom za dvigovanje in spuščanje + funkcijo samodejnega ponastavitve Vozilo – sistem za stabilnost vožnje Telematika, vključno z LIN akumulatorjem, senzorjem za povezavo in sledilnikom #Kolesa in pnevmatike 385/65 R22.5", proizvajalec po izbiri Aluminijasta platišča, polirana, proizvajalec Alcoa Dura-Bright #Elektrika 24 voltov, večprekatne luči, stranska rumena LED osvetlitev Nosilec luči, barvan v RAL 9010, čisto belo Brez garancije za prevleko/barvanje pri prebarvanih obdelanih dodatnih delih. 2 beli pozicijski luči spredaj 2 belo/rdeči luči za ohranjanje voznega pasu zadaj 2 x 7-polne in 1 x 15-polna varnostna vtičnica spredaj LED delovna luč na strani, na obeh straneh nameščena v višini prvega prečnega nosilca za opornimi nogami 2 dodatni LED delovni luči, na zadnji strani #Ponjava Ponjava z varjenimi horizontalnimi in vertikalnimi trakovi Na slikah so arhivske fotografije! Vozilo je po potrebi v uporabi!

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: Produktpalette, lastna masa: 6.000 kg, največja dovoljena obremenitev: 32.000 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 2.790 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5", stanje pnevmatik: 100 odstotek, barva: originalen, Leto izdelave: 2026, Prihranite pri stroških transporta! Na zahtevo dostavimo do tri platforme, zložene v varčno strukturo treh platform. Tako boste uživali v bistveno nižjih stroških transporta. Rešitev za transport, prilagojena vašim potrebam Konfigurirajte svoje vozilo Fliegl glede na vaše zahteve. Prikazano vozilo je zgolj primer. Proizvodnja in oprema potekata individualno, glede na želje stranke. #Podvozje, sedlo, prevozniška služba Finozrnat jekleni varjeni okvir, sedelna plošča z zamenljivim 2-palčnim kraljevskim členom Zunanji okvir, rahlo nagnjen, nova izvedba z "Load-Lock-profilom" za pritrditev jermena 24 ton, dvostopenjska podpora, upravljanje z ene strani, s polkrožnim spodnjim delom in ravno priključno ploščo, z izravnavo nagiba Opomba: Svoboden kot opore ali svoboden kot nagiba nazaj, pribl. 1930 mm Izvlečna lestev na zadnji strani Zaklep za vrata na strani 2 podstavka z držalom Stranski zaščitni odbijač iz aluminija Spodnji zaščitni odbijač iz pocinkane jekla Četrtaste blatnike spredaj in za osjo z zaščitnimi plošči proti brizganju, v skladu z EG Zaščitni odbijač na zadnji strani 2 nosilca za rezervno kolo za 1 kolo, z kompletom za pritrditev kolesa 1 rezervno kolo, proizvajalec enak kot pri osnovnih pnevmatikah, jeklena felna 1 plastični orodjarni kovček, š=600 / v=425 / g=460 mm, zaklenljiv #Osi + vzmetenje BPW osi s kolutnimi zavorami s premerom koluta 430 mm "Osno/podvozje lasersko merjeno" - zmanjšanje obrabe pnevmatik in porabe goriva Zračno vzmetenje 1. os: avtomatska dvižna os, vključno s prisilnim spuščanjem in pomočjo pri vožnji, upravljanje z "3-kratno zaviranje" (pomoč pri vožnji deluje do preseganja obremenitve osi za 30 % in do hitrosti največ 25 km/h) #Zavorna sistema Dvo-vodna zračna zavora Barvno označena vodila za lažje vzdrževanje Zavora na vzmet z zadrževalno funkcijo 2 varno nameščena priključka spredaj, brez povezovalnega kabla EBS, elektronski zavorni sistem z vtičnico EBS spredaj, brez povezovalnega kabla Pozor: Prikolico sme vleči samo vlečna vozila, ki zagotavljajo učinkovitost ABS! z ventilom za dvig in spuščanje Vozilo - sistem za stabilnost vožnje #Kolesa in pnevmatike 385/65 R22.5", jeklene felne, srebrna barva #Elektrika 24 Volt, večkamerske luči, stranske rumene LED luči 2 beli pozicijski svetili spredaj 2 belo/rdeči stranski svetili zadaj 2 x 7-polne varno nameščene vtičnice spredaj, brez povezovalnega kabla #Pod Lhedpfx Aezmtc Aedgoi Plasti, natisnjene s sitotiskom, debeline cca 30 mm, na 8 vzdolžnih podporah za visoko točkovno nosilnost, do maksimalne obremenitve osi viličarja 7.900 kg Na zadnji strani jeklena/valovita pločevina, nameščena na cca 300 mm dolžine #Sprednja stena / vogalni okviri spredaj 135 cm visoka, vogalni okviri iz jekla, v izvedbi s polno prostornino, pritrdilni mehanizem za stransko ponjavo na sprednji steni, "Crash-Blocker", na spodnji notranji strani na cca 140 mm višine z jeklenim zaščitnim odbijačem #Država registracije / Tablice Nemčija Odobritev po EG 2007/46 24/7 servisna telefonska številka opcijsko nakladanje v paketu 3 kosov vključno z pritrditvijo in varovanjem tovor Proizvajalčev certifikat Fliegl o konstrukcijski trdnosti po EN 12642 XL Opozorilna tabla po ECE - 70

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33902035352, lastna masa: 6.460 kg, največja dovoljena obremenitev: 32.540 kg, skupna masa: 39.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 3.000 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, skupna višina: 40.000 mm, vzmetenje: zrak, velikost pnevmatike: 445/45 R19,5", stanje pnevmatik: 100 odstotek, barva: originalen, Pozor: Slike so arhivske! #Šasi, pete za sedelno prikolico, transportno podjetje Fino zrnata jeklena varjena konstrukcija, plošča za sedelno prikolico z zamenljivim 2-palčnim kraljevskim zatičem Izvedba za prevoz z vlakom/tovor na železnici Koda za pritrditev tovora za prevoz z vlakom XL sestavljena iz 4 prijemnih robov Skupna višina vozila v najvišji točki pri spuščenem zračnem vzmetenju največ 4000 mm pri uporabi prikolice z "žepom", na 880 mm oporni nogi, koda za železniški promet P400 Ponjava z integriranim zaščitnim robom za prijemala v skladu s specifikacijami "DB". PRO SLIDE, dodatna vodilna plošča spredaj levo in desno pred kraljevskim zatičem "Heavy Push Frame", zunanja ojačitev okvirja na prečnem nosilcu za intenzivno stransko obremenitev 1 par podpornih nog z zobniškim pogonom zadaj, s pravim spodnjim delom in enostranskim upravljanjem na desni strani (FR). 4 pari priveznih ušes, označeni z rumeno barvo Stranska zaščita palet v robustni izvedbi, na obeh straneh, povsem privita Predal za 32 vložkov, na obeh straneh (16 kosov na stran), pod nosilno površino 1 dokumentna škatla, 36x26x4 cm #Osi + vzmetenje SAF osi s kolutnimi zavorami kot os za kombinirani promet, z jekleno vrvjo kot zaščito pred prevelikim spuščanjem ali alternativno konstrukcijo "Lasersko merjenje osi/podvozij", zmanjšanje obrabe pnevmatik in porabe goriva Zračno vzmetenje #Zavorni sistem Dvojno vodni zračni zavorni sistem Barvno označene vodne povezave za enostavno vzdrževanje Zavora na vzmet, samodejno vključena 2 varno nameščena priključna glavna cilindra spredaj + zračne povezave tipa C + CA (GB) EBS, elektronski zavorni sistem z vtičnico EBS spredaj z ventilom za dvigovanje in spuščanje Sistem za stabilnost vozila med vožnjo Kazalnik obrabe zavor prek informacijskega centra prikolice in prikaz podatkov o vozilu, kot so obremenitev osi, prevožena razdalja in diagnostična/sistemska sporočila Sistem za nadzor tlaka v pnevmatikah, prek EBS #Kolesa in pnevmatike Lhjdpfx Adszl D Rzjgei 445/45 R19,5", proizvajalec Continental Jeklena platišča, tovarniška srebrna barva vključno z zaščitnimi pokrovčki za vijake na kolesih #Elektrika 24 Volt, 4 x 3-komorne luči + 1 okrogla luč za vzvratno vožnjo in + 1 okrogla luč za meglo 2 beli/rdeči stranski gabaritni luči zadaj 2 x 7-polne in 1 x 15-polna varno nameščena vtičnica spredaj 2 dodatna LED delovna svetila zadaj #Pod Plošče, izdelane z metodo sitotiska, debeline približno 30 mm, nameščene na vzdolžnih nosilcih za visoko točkovno nosilnost za viličarje, nosilnost osi viličarja do največ 7100 kg "Premium zaščitni premaz tal", talna obloga, po celotnem obodu zatesnjena #Stranski nosilci 3 pari drsnih stranskih nosilcev, ki se lahko premikajo po celotni dolžini, z 4-kratnimi vložki in spodaj z dolgim žepom. 3 pari položajev stranskih nosilcev #Vložki 5 vrst aluminijastih V-vložkov #Ponjava Ponjava z varjenimi horizontalnimi in vertikalnimi trakovi vključno s 3 x žepi za dokumente na vsaki strani Zatezni mehanizmi iz nerjavečega jekla #Streha Drsna ponjava, zadnji del je dvigljiv, ponjava se lahko pomika od zadaj proti spredaj, L-nosilec za avtomobilsko industrijo, notranja širina med nosilci strehe približno 2490 mm, barva ponjave: bela Strešna ponjava z 5-kratno zaščito na prečnih nosilcih strehe, torej z 5 zaponkami na vsakem prečnem nosilcu tudi vsak drugi prečni nosilec ima kavljek za pritrditev strehe Streha je neelastična, ob nakladanju in razkladanju se nosilec strehe komaj upogne optimalna odbijačna letvica zadaj, na vrhu zadnjega nos

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33902024358, lastna masa: 6.149 kg, največja dovoljena obremenitev: 28.851 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 2.790 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22.5", barva: modra, The images shown are archive photos; the vehicle may still be in use! Chassis Semi-trailer Haulage Fine-grain steel welded construction, fifth wheel plate with interchangeable 2" kingpin Lhodpfx Aswyiw Eodgei Outer frame slightly inclined with 'Load-Lock profile' for lashing strap attachment Note! To hook in the straps in conjunction with drop sides, the side walls must be opened! Pair of lashing eyes additionally flush-mounted in the outer frame, each rated to 2.5 t 24 t, two-speed landing gear, single-sided operation, with straight lower section, without compensating mechanism Pull-out ladder at rear Side door retainers Wheel chocks with holder Pallet box for 32 Euro pallets (long version), ground clearance approx. 300 mm. Note: Free landing leg corner dimension or rearward swing clearance approx. 1930 mm Rear underrun protection, steel, galvanized Full-width rear mudflap Half-shell fenders With anti-spray mudflap only on the last axle Rear collision protection 'Blocker' – transverse galvanized steel angle as forklift and rear door hinge protection Pair of ferry rings, yellow marked Pallet stops on both sides, approx. 15–20 mm high, bolted design (loading height reduced by approx. 15–20 mm) Spare wheel holder for one spare wheel, complete with fixing kit, basket design by Schoch! Spare wheel, same make as original tyres, steel rim Stainless steel toolbox, w=600/h=400/d=500 mm, with polished, lockable door Stake pockets Right side: 5 rows of aluminium V-insert slats Left side: no insert slats Rear wall / Rear corner posts Rear corner posts steel, up to roof edge, lashing for tarpaulin with round tubes and tensioning ratchet Rear portal doors, double-leaf, each with 2 internal bar locks Tarpaulin Tarpaulin with integrated horizontal and vertical belts Quick Lock system for side curtain with central locking, one-sided on left Tension locks in stainless steel on right duty-free cable all around, with holder on front wall (no customs lock, not in conjunction with Quick Lock) Customer branding on side curtains and rear portal Tarpaulin with high-strength built-in spring steel strips, left side (note: no insert slats on left when equipped) Roof Sliding roof, rear end lift-up, can be pushed open front-to-rear, tarpaulin colour: white EcoLift – lifting roof, raisable by approx. 380 mm on both sides, with gas strut assistance, Optimum rear rain rail, top of rear bow, above doors Paintwork Frame: hot-dip galvanized with passivation Landing legs: black coated Front corner posts: galvanized and painted to front wall colour Front wall: MB 5328 blue Rear corner posts: galvanized and painted to rear wall colour Rear wall: MB 5328 blue Tarpaulin: RAL 5010 gentian blue Pallet box lid: RAL 2011 deep orange The images shown are archive photos; the vehicle may still be in use!

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT34002026856, lastna masa: 5.592 kg, največja dovoljena obremenitev: 29.408 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2020, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, skupna dolžina: 13.850 mm, skupna širina: 2.550 mm, skupna višina: 4.000 mm, vzmetenje: zrak, velikost pnevmatike: 385/65 R22,5", barva: bela, The images are for reference only (archive images)! The vehicle may still be in use! Lhedpfxox Rq Sls Adgoi Chassis – Semi-Trailer Haulage Fine-grain steel welded construction in reinforced Scandic design, 5th wheel plate with interchangeable 2" kingpin Outer frame slightly inclined with "Load-Lock profile" for attaching lashing straps Lashing rings for insertion in "Load-Lock Profile", each 6 t, loose 24 t, 2-speed landing gear, single-sided operation, with straight lower part, without compensating rod Free pivoting radius to landing leg approx. 2200 mm, landing leg width approx. 2350 mm 2 Wheel chocks with holder Side underrun protection: Aluminium Rear underrun protection: Galvanised steel Quarter mudguards in front of and behind axle unit With anti-spray mud flaps only on last axle 1 Plastic toolbox with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) 1 pair of stake pockets flush-mounted at the very front in the outer frame/floor, 83 x 83 mm inner dimension 2 detachable stanchions, w=80/ d=80/ l=1200 mm, hot-dip galvanized Note: Stake pockets/insertion stanchions are not suitable for the sole securing of long material, pipes, etc. without strapping 4 pairs of ferry rings, marked yellow Axles & Suspension 3x BPW drum brake axles "Axles/chassis laser measured" reduces tire wear and fuel consumption Air suspension Brake system 2-line compressed air braking system Color-coded line routing for easier service Spring-loaded parking brake 2 foolproof coupling heads at front, without connecting line EBS system manufacturer: Wabco Premium, electronic braking system with EBS socket at front, without connection cable, Wabco Premium incl. open CAN bus for telematics Attention: The trailer may only be towed by tractors which guarantee the effectiveness of the ABS! With lift & lower valve Vehicle – driving stability system Electric 24 Volt, multi-chamber LED lights with resistor, side yellow LED lighting, license plate LED lighting (note: on some tractor units, malfunctions may be displayed although functionality is given) 2 white position lights at front 2 white/red lane marker lights at rear 2x 7-pin foolproof sockets at front, without connector cable Front wall / front corner stanchions 2 at 580 mm high, steel corner stanchions in high capacity version, release mechanism for side curtain at front wall "Crash Blocker", lower inside at approx. 140 mm height with steel impact protection Insert slats Rows of timber insert slats Curtain Curtain with welded-in horizontal and vertical straps Stainless steel over-centre locks Floor Anti-slip phenolic bonded plywood approx. 30 mm thick on longitudinal supports for high point load capacity, suitable for forklift axle loads up to max. 7100 kg Note: Floor warpage due to weather possible (no warranty)! Rear wall / rear corner stanchions Rear corner stanchions steel up to lower edge of roof, hooks for curtain with round tube and curtain tensioning ratchet Rear portal doors, double-leaf, each with 2 internal locking bars Roof Sliding roof, rear end lift-up, roof slides from rear to front, curtain color: white Optimal rear rain guard, on rear hoop, above the doors Country of Registration/Plates Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-line number plate holder Conspicuity marking with reflective strips in accordance with ECE R 048, white on sides and red at rear

Stanje: novo, največja dovoljena obremenitev: 16.920 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Skupna teža: 24.000kg/ 30.000kg Lastna teža: 7.080kg Nosilnost: 16.920kg/ 22.920kg Skupna dolžina: 10.825mm Nakladalna dolžina: skupno 8.200mm Širina: 2.5250mm Lhsdpfx Aozhhw Dedgoi Višina nakladalne površine: 900mm Dodatne informacije plus predhodni prevoz / priprava iz skladišča Wiesmoor 26639, 1.280,00 € / neto Podvozje nizkopodni priklopnik Jeklena varjena konstrukcija Vrtljiva plošča s trdnim krogličnim ležajem, omarica za orodje vgrajena v prednji del vrtljive plošče Zložljive zadnje podporne noge 2 zagozdi za kolesa z nosilcem Bočna zaščita iz aluminija Zadnja blatnika po celotni širini (ni združljivo z nosilcem za viličar) Četrtinski blatniki pred in za 1. osjo z zaščito proti pršenju, zaščita proti pršenju za 2. in 3. osjo 1 nosilec za rezervno kolo z pritrdilnim kompletom 1 plastična škatla za orodje, širina=600 / višina=425 / globina=460 mm, zaklepna Razširitve izvlečne do 3.000 mm (ne na zadnji poševnini) (sled širine transportiranih gradbenih strojev ali vozil ne sme presegati zunanjega okvirja 2.550 mm) Shranjevalni prostor za lesene deske na sredini nakladalne površine Lesene deske 70 mm za razširitev na 3.000 mm Pritrdilne točke za nizkopodnik 3 para pritrdilnih točk po 10 t vgrajenih spredaj v tla 6 parov pritrdilnih gobic zgoraj in ob strani zunanjega okvirja po 10 t 1x v predelu vrata ostale enakomerno porazdeljene vmes 1x na zadnji poševnini 5 parov pritrdilnih obročkov v zunanjega okvirju po 5 t (možnost predelave v žepke za kole) 1 par zložljivih pritrdilnih točk dodatno v nizkopodni površini za 3. osjo po 10 t 1 par vijačnih pritrdilnih točk spredaj v kotih po 6,7 t, z veliko pritrdilno ploščo, vključno z navojem kot nasprotnik Vlečna naprava priklopnika z vrtljivo ploščo Vlečna roka s preizkušenim 40 mm vlečnim obročem Preme in vzmetenje Bobnaste premne, izbira proizvajalca "Premne/podvozje lasersko izmerjene" zmanjšujejo obrabo pnevmatik in porabo goriva Zračno vzmetenje s funkcijo dviganja/spuščanja Zavorni sistem Dvovodna zračna zavora Barvno označene cevi za enostavno servisiranje Zavorni zasilni zavorni mehanizem 2 nezamenljivi spojni glavi spredaj z povezovalnimi cevmi do vlečnega vozila 24V EBS, elektronski zavorni sistem z EBS vtikačem spredaj, s povezovalnim kablom Pozor: Priklopno vozilo sme vleči samo vozilo, ki omogoča učinkovitost ABS! Prepoznavanje osi preko EBS-Canbus signala, za prikaz na zaslonu v kabini voznika, tovornjak mora biti prilagojen, ni nameščen (ni overjene tehtnice) Sistem stabilnosti vozila "RDKS" sistem za nadzor tlaka v pnevmatikah po ECE R 141, prikaz na zaslonu v vlečnem vozilu, preko EBS, ni nameščen v tovornjaku (pogoj je izpolnjen v osnovnih pnevmatikah) Kolesa in pnevmatike 235 / 75 R 17,5" Pnevmatike po izbiri proizvajalca Jekleni platišči v dvojni postavitvi, tovarniško srebrna barva Elektrika 24V, večkomorni žarometi, bočna rumena LED osvetlitev Bočna rumena LED osvetlitev povezana s smerniki "utripajoče stranske luči" 2 bele pozicijske luči spredaj 2 belo/rdeči označevalni luči zadaj 2x 7-polna nezamenljiva vtikača spredaj, s povezovalnim kablom 1 LED opozorilna luč z nosilcem, vklop preko pozicijske luči (svetilka snemljiva) 2 para opozorilnih tabel, dvojno LED osvetljene, izvlečljive do 3.000mm Tla Sprednji del jeklena tla nato cca. 70 mm mehkih lesenih desk, na območju koles jekleni/ribasta plošča Zadnja poševnina s 70 mm mehkim lesom Nizkopodna površina z zadnjo poševnino 8.200 mm Nakladalne rampe Jeklene rampe dolžine 3.000 mm, širine 750 mm, premakljive bočno (nadaljevanje spodaj)

Stanje: novo, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33901014200, lastna masa: 6.700 kg, največja dovoljena obremenitev: 28.300 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, višina nakladalnega prostora: 900 mm, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, skupna višina: 2.500 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", stanje pnevmatik: 100 odstotek, barva: sivo-črna, Chassis, semi-trailer, forwarding version Fine-grain steel welded construction, fifth wheel plate with replaceable 2" king pin Outer frame slightly chamfered, new design with "Load-Lock profile" for securing strap hooks 24 t, 2-speed landing gear, single-sided operation, with straight base, without telescopic adjustment Free landing leg corner dimension or free rear swing radius approx. 1920 mm 2 wheel chocks with holders Side underrun protection, aluminium Rear underrun protection, steel Quarter-shell mudguards in front of and behind each axle Spray flaps in front of the 1st axle and behind each axle with anti-spray, according to EC 1 lockable plastic toolbox, w=600 / h=425 / d=460 mm (lock not included) Axles + Suspension SAF drum brake axles "Axles/chassis laser alignment" reduces tyre wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start assist, operated by "3x braking" (start assist is active up to a 30% overload on the axle and up to a maximum speed of 25 km/h) Axle lift below recommended driving height, therefore no warranty for tyre damage Brake system 2-line compressed-air brake system Colour-coded line routing for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS electronic braking system with EBS socket at the front, without connection cable Lsdeza A Txopfx Adgjhi Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With raise & lower valve Vehicle dynamic stability system Wheels and tyres 235/75 R17.5, brand according to manufacturer's choice Steel rims, factory silver Electrics 24 V, multi-chamber lamps, yellow LED side marker lamps 2 white marker lamps at the front 2 white/red lane marker lamps at the rear 2 x 7-pin and 1 x 15-pin fail-safe sockets at the front, without connecting cable Floor Phenolic plywood approx. 30 mm thick, for high point load capacity, suitable for forklift axle load up to max. 5,600 kg Front wall / front corner posts 25 mm aluminium hollow section, 1,350 mm high, front corner posts in steel, volume design Country of registration / plates Germany With Dekra inspection and certificate (according to §13 EC FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame: DB 7350 Novagrau Front corner posts: hot-dip galvanized Front wall: aluminium

Stanje: rabljeno, številka stroja/vozila: WFDFLT33901007921, lastna masa: 9.000 kg, največja dovoljena obremenitev: 26.000 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2018, naslednji pregled (TÜV): 02/2027, dolžina tovornega prostora: 15.150 mm, širina tovornega prostora: 2.480 mm, skupna dolžina: 15.350 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", barva: črn, Attention, the images shown are archive photos! The vehicle may currently be in use! Weights and Dimensions: Permissible/Technical Gross Weight: 35,000 / 39,000 kg Permissible/Technical Payload approx.: 26,000 / 30,000 kg Permissible/Technical Axle Load: 24,000 / 27,000 kg Permissible/Technical Kingpin Load: 11,000 / 12,000 kg Unladen Weight approx.: 9,000 kg +/- build tolerance Overall length approx.: 13,850 + 1,500 mm Overall width max.: 2,550 mm Overall height approx.: 3,200 mm Internal length approx.: 13,650 + 1,500 mm Neck length approx.: 4,050 mm Low bed length approx.: 9,600 + 1,500 mm Internal width approx.: 2,480 mm Loading height (low bed) approx.: 900 mm Fifth wheel height approx.: 1,150 mm Kingpin mounting dimension approx.: 1,680 mm Front corner dimension approx.: 2,040 mm Chassis | Fifth-Wheel Platform Haulage Fine-grained steel welded construction, fifth wheel plate with replaceable 2" kingpin Lashing rings recessed into outer frame, each rated at 2.5 t 24 t, 2-speed landing gear, single-sided operation, with straight lower section, no lateral compensation Wheel chocks with holder Side underrun protection, aluminium Rear underrun protection, steel Quarter-shell mudguards in front of 1st axle and behind each axle With anti-spray mudflaps behind each axle Rear collision guard Plastic toolbox with drawer and shelf, w=650 / h=520 / d=670 mm Document box, front bulkhead mounted Telescoping Central tube frame made of cleanly welded, interlocking telescopic frame sections. Extendable by max. 1,500 mm and lockable after approx. 1,500 mm, outer frame sections approx. 1,500 mm long for insertion into the outer frame when extended Locking by mechanical pin locking Axles & Suspension SAF drum brake axles Air suspension Brake System 2-line compressed air brake system Spring-loaded parking brake 2 error-proof coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connection cable Note: This trailer may only be towed by tractors that ensure the effectiveness of the ABS! With lift & lower valve Wheels & Tires 235 / 75 R 17.5 Steel twin wheels, factory silver Electrics 24 Volt, multi-chamber rear lights, lateral LED marker lights (yellow) 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin error-proof sockets at the front, without connection cable Rotating beacon with holder, controlled via parking light (lamp removable) Floor Non-slip phenolic plywood panels approx. 30 mm thick, for high point load capacity, suitable for forklift axle loads up to max. 7,100 kg Where required in wheel arch areas: steel/chequer plate covering Lodey Slp Ijpfx Adgjhi Bulkhead/Front Stakes 25 mm aluminium hollow section, 1,950 mm high, steel front stakes, full height in heavy duty design Certification / Signage With Dekra inspection and appraisal Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour marking with reflective tape according to ECE R 048, lateral white and rear red Attention, the images shown are archive photos! The vehicle may currently be in use!

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, številka stroja/vozila: WFDFLT33903000364, lastna masa: 6.120 kg, največja dovoljena obremenitev: 28.880 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, prva registracija: 12/2022, dolžina tovornega prostora: 13.650 mm, širina tovornega prostora: 2.480 mm, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17,5", barva: srebrn, Attention: The images are archive photos! The vehicle may currently be in use! Weights and Dimensions: Permissible/technical gross weight: 35,000 / 39,000 kg Permissible/technical payload approx.: 28,880 / 32,880 kg Permissible/technical aggregate load: 24,000 / 27,000 kg Lodpfey Slhqox Adgshi Permissible/technical fifth wheel load: 11,000 / 12,000 kg Unladen weight (basic version) approx.: 6,120 kg +/- build tolerance Overall length approx.: 13,800 mm Max. overall width: 2,550 mm Overall height approx.: 2,388 mm Gooseneck length approx.: 4,050 mm Low-bed length approx.: 9,600 mm Loading height in low-bed, loaded approx.: 900 mm Internal width approx.: 2,480 mm Fifth wheel height approx.: 950 mm King pin installation dimension approx.: 1,680 mm Front corner dimension approx.: 2,040 mm Chassis semi-trailer for haulage company Fine-grained steel welded construction, fifth wheel plate with replaceable 2" king pin Telescoping at the beginning of the low-bed extendable by approx. 1,500 mm, lockable every 500 mm Slightly sloped new outer frame design with "Load-Lock profile" for securing lashing straps "Patented Load-Lock-Cross" for attaching lashing straps, mounted on the crossmember underneath the outer frame 24 t two-speed landing gear, single-sided operation, with straight lower section, without load equalizer Free landing leg corner dimension or free rear swiveling radius of approx. 1,920 mm Side underrun protection: aluminum Rear underrun protection: steel Quarter shell mudguards 9 pairs of lashing/ stanchion rails recessed across the floor up to the main frame, approx. 100 mm high. With 20 mm round steel bars top and bottom, spacing between bars approx. 60 mm. Bottom with angle plate as closure, half open downwards. For securing and inserting stanchions 80 x 80 mm (3 pairs in gooseneck, 6 pairs in low-bed area) 3 pairs of stake pockets recessed in the outer frame, internal dimension approx. 72 x 42 mm Axles & Suspension: Drum brake axles as per manufacturer’s choice "Laser-measured axles/chassis" for reduced tire and fuel consumption Air suspension Brake system: 2-line compressed air braking system Color-coded piping for easy service Spring-loaded parking brake 2 foolproof coupling heads at the front, without connecting line EBS electronic braking system, EBS socket at front, no connecting cable Note: The trailer must only be towed by tractor units that guarantee the effectiveness of the ABS! With lift and lower valve Vehicle stability system Wheels and Tires: 235/75 R17.5, manufacturer at the buyer’s discretion Steel rims, factory silver Electrics: 24 volt, multi-chamber lights, yellow LED side lighting (recessed inward) 2 white position lights front 2 white/red lane marker lights rear 2 x 7-pin foolproof sockets at the front, no connecting cable 1 additional LED work light at rear, switched via reverse light Floor: Approximately 30 mm thick anti-slip plywood, high point load capacity, suitable for forklift axle loads up to max. 5,600 kg Front wall / front corner stanchions: 25 mm aluminum hollow profile, 1,350 mm high Country of registration / plates: Germany Inspection and certificate in Bosnia 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective tape in accordance with ECE R 048, white on the sides, red at the rear Warning sign according to ECE 70 Painting: Frame: hot-dip galvanized incl. passivation “15-year guarantee against corrosion perforation” Front corner pillars: hot-dip galvanized Front wa

Stanje: novo, največja dovoljena obremenitev: 26.100 kg, skupna masa: 35.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.200 mm, širina tovornega prostora: 2.520 mm, višina nakladalnega prostora: 900 mm, skupna širina: 2.550 mm, Vehicle / Body: Low-bed semi-trailer First registration: New vehicle Gross weight: 35,000 kg / 47,000 kg Unladen weight: 8,900 kg Payload: 26,100 kg / 38,100 kg Overall length: 13,300 mm Loading length: 9,200 mm Width: 2,520 mm Loading height: 900 mm Further information Chassis: Low-bed semi-trailer Steel welded structure, fifth wheel plate with replaceable 2" king pin and two king pin positions (not in combination with forced steering) 24 t 2-speed landing gear, single-sided operation, with straight lower part, without thrust compensation Lhodpfsut Idnsx Adgji Rear support foldable 2 wheel chocks with holders Side underrun protection, aluminium Full-width rear mudflap Mud flaps with anti-spray in front of the 1st axle and behind each axle, in accordance with EU regulations 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Extendable width to 3,000 mm (not at the rear taper) (Note: The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Compartment for wooden planks on neck, transverse at front 70 mm wooden planks for extension to 3,000 mm Excavator arm recess over rear axles, extending to the rear, approx. 3,000 mm long, 650 mm wide, and 230 mm deep 2 pairs of lashing holes, each rated 5 t, in the excavator arm recess on side of main frame, approx. 300 mm from front and some 200 mm before rear taper Lashing points low-loader 11 pairs of lashing mushrooms, integrated top and side of the outer frame, each 10t 2x on gooseneck 9x distributed on load floor 2 pairs of lashing eyes front on gooseneck, each 5t 3 pairs of swivel lashing eyes on gooseneck, each 5t 2 pairs of folding lashing eyes additionally embedded in load floor, each 10t 1x at beginning of load floor 1x at end of rear taper 1 pair of preparation on the slope from gooseneck for 6.7t screw-on lashing eye (JDT) 8 pairs of ring lashing eyes recessed in outer frame, each 5t (convertible to stanchion pockets) 1 pair screw-on lashing eyes, each 6.7t (JDT), with large flange plate incl. thread as counternut Axles & suspension SAF or BPW drum brake axles, manufacturer's choice “Axle/chassis laser alignment” to reduce tire wear and fuel consumption Last axle is self-steering, with automatic reversing lock via reversing light and additional manual lock function via push button on vehicle Air suspension Wheels and tires 235 / 75 R 17.5" Manufacturer's choice Steel rims, twin configuration, factory silver Braking system 2-line compressed air brake system Coloured line routing for easy service Spring-loaded parking brake 24 Volt EBS, electronic braking system with EBS socket at front, without connecting cable Note: The trailer may only be towed by tractor units that ensure effective ABS functionality! 2 coded coupling heads at front, without connecting line With lift & lower valve Axle load detection via EBS-CAN-bus signal, for display in cab, truck must be appropriately equipped, no truck installation (not a calibrated scale) Vehicle stability control system Tire pressure monitoring system according to ECE R 141, display in tractor cab via EBS, truck installation required Electrics 24 Volt, multi-chamber lights, side yellow LED lighting Side yellow LED lighting linked to indicator "flashing side markers" 2 white position lights at front 2 white/red lane marker lights at rear 2x 7-pin coded sockets at front, without connecting cable 1 LED revolving beacon

Stanje: rabljeno, Funkcionalnost: popolnoma funkcionalen, lastna masa: 6.640 kg, skupna masa: 40.000 kg, prva registracija: 02/2023, dolžina tovornega prostora: 13.510 mm, širina tovornega prostora: 2.540 mm, vzmetenje: zrak, velikost pnevmatike: 445/45 R 19,5, barva: siv, Leto izdelave: 2023, 3-axle Mega Flatbed Semi-Trailer HeavyTrailer Gross weight: approx. 40,000 kg Fifth-wheel load: approx. 16,000 kg Axle load: approx. 24,000 kg Unladen weight: 6,640 kg Payload: 33,360 kg Length: 13,510 mm Vehicle width: 2,540 mm Coupling height: approx. 980 mm / 1,100 mm Loading height (unladen): 1,080 mm / 1,200 mm Chassis - Chassis frame construction made of welded longitudinal beams and continuous cross members - Wide underrun neck approx. 700 mm - 6 pairs of lashing rings (2,000 kg lashing capacity), welded into outer frame - 6 pairs of stake pockets (80 x 50 mm) in outer frame - 6 pairs of stake pockets (80 x 50 mm) inside on the longitudinal beam - 2 pairs of ferry lashings, painted yellow - 6 pairs of lashing rings (5,000 kg lashing capacity), welded into outer frame - Front wall approx. 2,000 mm high, with sheet metal cladding, bolted design - Large, edged premium rear lamp panel - Rear underrun protection, welded version (rectangular tube) - Side underrun protection, both sides Support Legs - 24 t telescopic landing gear, single-sided operation, half-moon with base plate Axles/Suspension - 3 axles à 8 t (technically 9 t), disc brakes - Second ride height: Button for 2nd ride height at bracket for raising and lowering (+ approx. 120 mm) - Air suspension, total stroke approx. 300 mm - Lifting and lowering device with 1 rotary slide valve - Holder for lifting/lowering device, bolted version - 6 tyres 445/45 R 19.5 - Wheel mounting via center centering Brakes - Dual-circuit compressed air brake system according to EC Directive 71/320 - With double eyelet valve for brake and spring brake - Test nipple for brake cylinder pressure at front right brake cylinder - Each coupling button red and yellow - Lifting/lowering device mounted at rear left in direction of travel - 2 x approx. 80 l air tanks in steel, painted black (1x brake, 1x lifting/lowering) Lighting System - Lighting system 24 Volt with large multifunction lights - Side marker lights (LED) with reflector - Front position lights, lower, white, one each on left and right - 15-pin plug and socket at front - EBS socket - License plate lighting Floor - 28 mm hardwood floor with galvanized omega steel profiles - Hardwood floor screwed onto the cross members Ledpsv Darpofx Adgehi - Omega profiles bolted to head frame Painting - KTL with zinc phosphating plus powder coating - Chassis + front wall: MB 7350 novagrau Accessories - Contour marking for flatbed vehicles - Front wall up to 2,000 mm high, with sheet metal cladding, plug-in type - Bracket for rotating beacon at rear - SmartBoard - ECE marking plate at rear - 4x warning signs, extendable - Access ladder rear right, foldable and extendable at rear - 2x wheel chocks with holder - 2 rubber bumpers at rear corners - Mud flaps at rear - Plastic fenders with anti-spray mud flaps - 4 pairs of container locks with retractable twistlocks, recessed into the floor, including additional cross members - Suitable for accommodating 1x40' and 2x20' containers - Open mesh box longitudinally in direction of travel (600 x 450 x 2,670 mm), galvanized, bolted