Faymonville 3-Achs-Beton-Innenlader-Prefamax nakup rabljenega (40.461)

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Fedpfx Apshlz R Setjpk Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, največja dovoljena obremenitev: 38.100 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 13.100 mm, širina tovornega prostora: 2.480 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5 3PMSF, barva: siv, Oprema: ABS, Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading platform: 5 pairs of fold-out lashing rings 3 pairs of fold-out lashing rings 1 pair of horizontal lashing rings at the front of the loading area Cut-outs in the outer frame of the loading surface for hooking in tension belts Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing legs: JOST landing legs with 2-speed gears for a 24 t lifting capacity Axles and tyres: BPW axles, two axles are fixed, two axles are self-steering, air-suspended, with drum brakes, with lift/lower function The self-steering axles come with an electro-magnetic reverse lock, which is activated via reverse gear or manually Axle toolkit Tyres: 205/65 R17.5 3PMSF Brake system: WABCO brake system according to EU regulations with EBS-E Steel construction: Steel structure made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Fpedpfx Apotphtmotok Electrical equipment: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame ensured by a 2-component zinc dust primer High-quality single-colour 2-component top coat in MB 7350 Novagrau No metallic paint possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system acc. to ECE R 141 At the galvanized front connection strip yellow-red air couplings 4 wheel chocks with holder on front wall Bracket at rear of gooseneck for ALU access ramps Galvanized folding supports under the chamfer of the loading surface Mount for a revolving beacon at the rear of the trailer Height-adjustable curtain structure Galvanized front wall with a tension mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof, sliding forward on ALU roof beam profiles, bolted to the front and rear wall In the loading surface, 3 pairs of sliding stakes Superstructure at rear hydraulically extendable to left and right by approx. 750 mm Sliding roof with upward swinging portal carrier Sliding tarp with 700 mm reserve length, with tension straps at intervals of approx. 600 mm Height to top edge of superstructure approx. 3,960 mm Journeys with the sliding roof open are not permitted and will damage the tarp Mounting rail for ALU access ramps at the rear of the vehicle At the gooseneck and at the rear panel left and right, each with a mount for warning signs incl. socket A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stake pockets for 100 x 50 mm insertable stakes in the outer frame of the loading area Lifting axle on the front axle controlled by TEBS E depending on current axle load and load status Rear structure with closed ALU double-wing doors A sanded, anti-slip paint layer on the checker plates on the gooseneck and on the loading surface BEKAMAX centralized lubrication system with standard grease NLGI-2 and a removable guard around the pump Speed stickers 80 km/h on rear and both sides Load manometer for axle load determination including load chart

Stanje: novo, lastna masa: 15.450 kg, največja dovoljena obremenitev: 65.550 kg, skupna masa: 80.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 21.900 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 925 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: Fpedpfsrigw Rox Aptek Gooseneck in SNT design for optimized platform length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractors: 4x2, 6x2, and 6x4 Loading Platform: Double-extendable loading platform, approx. 8,800 mm long with rear taper of approx. 500 mm x 10°. A support table approx. 300 mm wide is welded to the central beam, featuring elongated slots at the front and rear for optional bridge elements that can be hooked in and repositioned Pneumatic locking with conical locking pin and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adjust to the respective platform length Axles and Tyres: BPW axles and suspension, first axle self-steering, all other axles hydraulically and mechanically forced-steered First axle equipped with an electro-magnetic reverse lockout, activated via reverse gear and manually. Technical axle load: 12,000 kg. Air suspension with lift and lower valve Manufacturer by our choice Sockets and Lighting: 24-volt lighting system in accordance with EU regulations ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallizing Full steel construction, shot-blasted, then hot-finished with ZINACOR 850 Paintwork: 6-stage finishing process: Complete steel construction shot-blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer. Final paintwork in 2 coats of 2K paint in single-tone DB 7350 Novagrau, followed by cavity sealing with special wax Accessories: Detachable front wall made of steel, approx. 400 mm high Connection strip for supply lines to the tractor unit, fitted at the height of the outer frame profile ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets. If your pin configuration deviates from the ISO connector standard, please inform us 3 kW electro-hydraulic power unit for hydraulic functions (excluding hydraulic winches) 1 pair of plug-in ALU sidewalls on the gooseneck, approx. 400 mm high, anodized finish 3.5'' king pin. Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 2 wheel chocks with holder in front of the front wall Mechanical landing legs with 2-speed gearbox and crank Control valves for hydraulic ramps located on the right side of the vehicle 1 pair of mechanical rear supports Central lubrication system with 1 pump, BEKAMAX brand, using standard grease according to NLGI-2 Removable guard covering the pump(s) of the central lubrication system Remote steering from front and rear, controlled by cable remote with push buttons, with axle tracking control, no installation required on tractor unit Under the gooseneck and on the rear crossmember, one 7-pin socket with holder for warning signs each on left and right. One 7-pin socket on the rear crossmember Manual and documentation One-piece INOX stowage box, approx. 2,480 x 340 x 390 mm, straight design Please note that any special equipment and accessories will increase the unladen weight and correspondingly reduce the payload Warning package: 4 warning boards, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 LED position lights and brackets for beacon.

Stanje: novo, lastna masa: 10.600 kg, največja dovoljena obremenitev: 39.400 kg, skupna masa: 50.960 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 760 mm, vzmetenje: zrak, velikost pnevmatike: 205/65 R17.5, barva: siv, obratovalna teža: 10.600 kg, Oprema: ABS, Gooseneck: - Gooseneck with 30 mm hardwood flooring - Gooseneck at rear in straight version - 3 pairs of lashing rings (LC 5,000 daN) Extendable load floor: - Load floor in extendable configuration - 5 pairs of lashing rings foldable outward - 3 pairs of lashing rings foldable outward - 1 pair of lashing rings laying at the front end of the load floor - Cut-outs in the outer frame of the load floor for attaching tension straps - Approx. 48 mm hardwood flooring, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid axles, two self-steering axles - Air suspension with drum brakes, with lift/lower function - The self-steering axles are equipped with an electromagnetically operated reverse lock, which can be activated via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system compliant with EU regulations with EBS-E (4S3M) Steel structure: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, lighting 24 Volt, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - High-quality and durable corrosion protection on the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-colour 2-component (2K) top coat in Novagrau - Rear section metallised and painted in RAL 9010 (Pure White) Fedpfx Ast Ag Uwsptopk Included accessories: - One spare wheel with holder in front of the bulkhead - 2" king pin - Galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised connection bar at the front - 4 wheel chocks with holder at the front wall - Galvanised folding supports under the load floor slope - Holder for a warning beacon at the rear of the trailer - Galvanised extensions, extendable by approx. 230 mm per side - White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - European reflective markings (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear, galvanised plug-in side stanchions are removable, length of the body approx. 2,560 mm - 7 pairs of WADER container pockets - 1x 20ft container on the load floor; 1x 40ft container on the load floor; 1x 40ft container above the gooseneck; 2x 20ft container - 7 pairs of stanchion sockets for plug-in stanchions 100 x 50 mm in the outer frame of the load floor - Lift axle on the front axle with control via TEBS E, depending on the current axle load and load condition - Sliding plug-in rail for ALU loading ramps at the rear of the vehicle - Anti-slip sand finish painted on the checker plates on the gooseneck and load floor - Four warning boards extendable by approx. 400 mm, approx. 423 x 423 mm, each with a position lamp - Holder for warning beacon on the warning boards - 80 km/h speed stickers at the rear and on both sides - Axle load gauge for determination of axle loads inclu

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized Fpedeya E A Nspfx Aptek - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports Fodpjk Af Svofx Aptjpk - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: novo, lastna masa: 12.800 kg, največja dovoljena obremenitev: 36.200 kg, skupna masa: 49.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 375 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 12.800 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimised loading platform length, approx. 3,750 mm in length - Gooseneck can be raised/lowered hydraulically and is detachable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading platform: Fpsdpsvy Edcefx Aptsk - Low-bed with external beams, designed as a telescopic vessel bridge in low-profile construction with front extension - Length 6,850 mm x width 2,540 mm - One locking position approx. every 1,000 mm on the extension Rear running gear: - Rear running gear with closed outer frame featuring checker plate cover and continuous prism excavator recess, approx. 1,250/700 x 505 mm, open at the rear Axles, suspension and tyres: - “PENDLE-AXLE”, all axles force-steered hydro-mechanically - Hose rupture valves on axle equalising cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and pre-locking pins for securing in raised position - Final coat for axles with two layers of 2K acrylic paint, single-colour in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres: 245/70 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 14 - TPMS sensors installed in all wheels, incl. spare wheels Included accessories: - Plug-in steel front wall, approx. 400 mm high - 3 kW electro-hydraulic unit for hydraulic operations, except for hydraulic winches - One spare wheel with mounting adapter - External beams of the gooseneck with mounting holes for bolt-on lashing rings - Plug-in ALU side walls on the gooseneck, approx. 400 mm high, anodised - One plug-in ALU rear wall on the gooseneck, approx. 400 mm high, anodised - Checker plate covering on the gooseneck - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - Operating area lighting at the gooseneck with on/off switch - Hydraulic traverse to support the gooseneck on the tractor or a dolly - 2" king pin - Anti-slip stickers on the left chamfer of the gooseneck - The rear upper area of the gooseneck is closed with a removable cover - 4 wheel chocks with holders - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - 1 pair of steel ramps with climbing strips and retaining bolts for bridging the low-bed mounting hooks - The ramps can be placed over or between the hooks - Mounting option for steel drive-on ramps at the rear between the external beams of the gooseneck - Prepared for bolt-on container locks for 1 x 20ft on the external beams - Mechanical pin and lug coupling from low-bed to running gear for exchanging the loading platform or inserting extension beams - With electro-pneumatic-hydraulic couplings - The outer beams of the low-bed are coated with painted-on sand layer as anti-slip protection - Removable (galvanised) load floor, can be inserted in 3 elements between the external beams, with hardwood surface - Foldable extensions, approx. 230 mm per side - Hanging strip at the front of the rear running gear to the low-bed for loose approach ramps - 2 pairs of stake pockets recessed into the outer frame of the running gear, for plug-in stakes approx. 100 x 50 mm - Hanging strip for loose ALU approach ramps at the rear cross member of the vehicle - Central lubrication system with 2 pumps - Radio and cable remote control - 4 extendable warning signs, approx. 423 mm x 423 mm - Numerous lashing positions

Stanje: novo, lastna masa: 15.900 kg, največja dovoljena obremenitev: 63.500 kg, skupna masa: 68.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 12.700 mm, širina tovornega prostora: 2.740 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75/r17,5, barva: siv, obratovalna teža: 52.100 kg, Oprema: ABS, Gooseneck: Gooseneck in SNT design for optimal load bed length, approx. 3,300 mm long, rear with taper approx. 1,000 mm x 10° Technical fifth wheel load: 23,000 kg For tractor units: 6x2, 6x4, and 8x4 Load bed: Extendable load bed, approx. 9,400 mm long with rear taper approx. 500 mm x 10° A recess in the load bed as well as in the tapering section for accommodating the excavator dipper stick, approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, service lines are protected within the extendable beams and automatically adapt to the respective bed length Axles and Tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool 235/75 R 17.5 3PMSF twin tires Load index 143/141J (144/144F) Two-piece steel ramps: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide Hardwood covering Hydraulically folding ramp tips, each ramp hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward Braking system: Braking system by WABCO EBS-E according to EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 for optimal corrosion protection Surface treatment: Entire steel structure automatically blast cleaned with shot blasting after welding Second blasting treatment with corundum for optimal coating adhesion Final painting: 2 coats of 2-component paint in Novagrau, followed by sealing of cavities with special wax Rims in silver-grey Steel construction: Steel construction from high-strength fine-grained steels Fsdpfx Aomfqi Ieptepk Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Plug-in steel front wall, approx. 400 mm high Connection rail for service lines to the tractor unit Spiral cable for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit, with plug for the electro-hydraulic unit to control hydraulic operations, except for hydraulic winches Outer beam of gooseneck with mounting holes for bolted lashing rings First hole approx. 200 mm from the front, thereafter approx. every 400 mm One mounting hole in the rear upper area of the outer gooseneck beam for a bolted lashing ring Approx. 40 mm thick hardwood floor on the gooseneck, checker plate floor over the kingpin Guide plate on gooseneck for the fifth wheel plate, approx. 500 mm wide On the load bed, continuous and between the axles intermittent approx. 50 mm thick hardwood floor Load bed locking with conically welded locking profiles every 250 mm, including preload plate Slotted holes for attachable and movable bridging elements: on the fixed section behind the gooseneck at the front of the load bed 1 movable intermediate table for the extension tube with large cross-section Control valves for the hydraulic ramps on the right side of the vehicle Central lubrication system with 1 pump, standard grease according to NLGI-2 Radio remote control for steering operation, in addition to cable remote control, with 2 control lights on the receiver for single-track steering monitoring

Stanje: novo, skupna masa: 78.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 850 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck in SNT design to optimize loading area length, approx. 3,700 mm long, rear with a bevel approx. 1,000 mm x 10° • For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading Area: • Extendable loading platform, approx. 8,800 mm long with rear bevel approx. 500 mm x 10° • A recess in the platform and rear bevel to accommodate the excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Fodpforvw U Sex Aptopk Ramps: • One pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulically folding ramp tips • Ramps hydraulically adjustable separately approx. 235 mm outwards and approx. 215 mm inwards • Hardwood decking on the beveled part of the loading area • Ramp with hardwood decking • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent wheel suspension with BPW stub axles, 1st axle steered in advance, all other axles are hydromechanically forced steered • 1st axle with electromagnetic reverse lock via reverse gear and manual activation • Technical axle load: 12,000 kg • Hydr. axle compensation, hydraulic cylinders with shut-off valves • Tyres 245/70 R 17.5 • TPMS tyre pressure monitoring system according to ECE R 141 Accessories Included: • Plug-in steel front wall, approx. 400 mm high • 4 wheel chocks with holder • Front connection bar with yellow-red air couplings • 3 kW electro-hydraulic power pack for hydraulic control, except for hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings in the rear area of the gooseneck • On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized • On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood decking on the gooseneck, checker plate over the king pin • 3.5" king pin • Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide • Load area locking with conically welded arresting profiles every 250 mm • Incl. pre-tensioning plate • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the platform • Extendable (galvanized) widenings approx. 230 mm per side • 1 pair of fixed open wheel recesses up to extension, approx. 700 x 410 mm, in the platform in front of the 1st axle • Wheel recesses with checker plate covering and 15 x 15 mm square climbing strips, approx. every 200 mm • 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the platform between the 1st and 2nd axle • Wheel recesses with 15 x 15 mm square climbing strips and widenings in the lower section • ALU covers for the wheel recesses between 1st and 2nd axle, which can also be used as broadening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing strips, approx. every 200 mm on the outer frame of the bevel of the loading area • Central lubrication system with 1 pump, BEKAMAX brand, standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single wheel control • WABCO Smart Board system • The Smart Board is equipped with an odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and mounts for rotating beacon

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading area length, approx. 3,700 mm long, with rear tapering of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading platform: - Loading platform, approx. 9,700 mm long, with hydraulically foldable and lowerable rear section as well as hydraulically liftable front section for driving onto the gooseneck Axles and tyres: - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift/lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for the self-steering axle of a 3-axle unit - Automatic control of the self-steering axle when reversing via gyroscope sensor - Manual steering operation in forward and reverse using separate radio remote control - Manual operation enabled up to 10 km/h - System powered by separate electro-hydraulic unit Accessories included: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power pack - External beams on gooseneck with mounting holes for bolted lashing rings - First mounting hole approx. 200 mm from front, then approx. every 400 mm - One mounting hole at upper rear of external gooseneck beams for a bolted lashing ring - Grating cover with 5 mm sheet reinforcement on gooseneck and rear taper - 2" king pin - Guide plate on gooseneck for fifth wheel plate, approx. 500 mm wide - Round NATO socket at front connection bar (Maeler & Kaege VG 96 917) - 1 pair of removable side aluminium drop sides on gooseneck, approx. 400 mm high, anodized - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Continuous grating cover with 5 mm steel underlay for additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covering plates and in transition areas between neck and lift bed, between lift bed and loading platform, and between loading platform and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders are fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching tension straps Fsdoyw Sakjpfx Aptjpk - Extensive lashing positions - Hydraulically lowerable rear section for loading and unloading, can be raised to shorten total coupling length - Load capacity while driving in horizontal position: 10,000 kg - Shortening of total coupling length when raised: 2,350 mm - Painted-on sand coating on the complete ramp, except for the extendable galvanized part of the ramp - Hydraulically extendable rear extensions for loading and unloading - Radio remote control: - Control of hydraulic lift bed - Control of hydraulic lifting of rear extension - Control of hydraulic extension of rear extension - 1st axle with starting aid - Centralized lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable

Stanje: novo, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.700 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17.5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimal load deck length, length approx. 3,700 mm, rear end with chamfer approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Load deck: - Load deck, approx. 9,700 mm long with hydraulically folding and lowering rear section, as well as hydraulically liftable deck at the front for driving over the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle steering on trailing arm - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manual switch - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system compliant with ECE R 141 Included accessories: - Plug-in steel front wall approx. 400 mm high - Yellow-red air couplings on the front connection rail - 3 kW electro-hydraulic power pack for control of hydraulic functions, except hydraulic winches - Outer beams on the gooseneck with fixing holes for screwable lashing rings Fpsdpfxsyw R Srs Aptek - First hole approx. 200 mm from front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - One mounting hole on the upper rear area of the outer beams of the gooseneck for a screwable lashing ring - On gooseneck and rear chamfer, grating covering with 5 mm plate reinforcement - 2" kingpin - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - Round NATO socket on the front connection rail (Maeler & Kaege VG 96 917) - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodised - 4 wheel chocks - Electric cable winch, approx. 5,400 kg pulling force, with remote control - Wire rope approx. 24 m long, rope diameter approx. 9.5 mm, incl. rope pressure roller - Winch mounted at the front inside of the gooseneck - Plastic tarpaulin cover for the winch - Mechanical landing gear with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Continuous grating covering with 5 mm plate reinforcement for additional strength, designed for point loads: - on the lifting bed - on the load deck - on the hydraulically lowerable rear section - Painted-on sand coating on the gooseneck covers and transitional areas between neck and lift bed, between lift bed and load deck, and between load deck and ramps - 1 spare wheel with mounting adapter under the load deck on the right in front of the axles - Hydraulic lifting bed, length approx. 2,500 mm, load capacity in driving position (raised): 9,000 kg - Hydraulic cylinders fitted with load-holding valves - Cut-outs in the outer frame of the load deck and lifting bed for lashing straps - Extensive lashing positions - Hydraulically lowerable rear section for loading/unloading and can be raised to reduce overall train length - Load capacity in driving position (horizontal): 10,000 kg - Reduction of overall train length when raised: 2,350 mm - Painted-on sand coating on the entire ramp, except for the extendable galvanised ramp section - Hydraulic, extendable rear extensions for loading and unloading - Remote control: - Lifting bed operation - Lifting device for rear extension operation - Extension of rear extension operation - 1st axle with traction aid - Central lubrication system with 1 pump - 4 warning boards, approx. 423 x 423 mm, extendable

Stanje: novo, lastna masa: 14.800 kg, največja dovoljena obremenitev: 61.700 kg, skupna masa: 76.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, velikost pnevmatike: 235/75/r17,5, barva: siv, Oprema: ABS, Gooseneck: • Gooseneck with rear chamfer of approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Loading Platform: • Extendable loading platform with rear chamfer of approx. 500 mm x 8° • 9 pairs of folding external lashing rings • 1 pair of recessed lashing rings at the front of the loading platform • Cutouts in the outer frame of the loading platform for attaching tension belts • Approx. 48 mm thick hardwood flooring, checker plate above the axles Landing Legs: • JOST mechanically operated landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: • BPW axles and suspension, 1st axle steering, 2nd and 3rd axle fixed, 4th and 5th axle follow-steering • Technical axle load: 12,000 kg • 1st, 4th, and 5th axles with electromagnetic reverse lock, activated via reverse gear or manually • Tyres: 235/75 R 17.5 3PMSF Brake System: • WABCO brake system in accordance with EU regulations including EBS-E (4S3M) Paintwork: • Premium and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer • High-quality single-color two-component (2K) topcoat in MB 7350 Novagrau • Rear section metallized and painted in RAL 9010 (Pure White) Steel Construction: • Steel structure made from high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC (yield strength 355MPa) • S690QL/S700MC (yield strength 690MPa) Accessories: • One spare wheel with holder in front of the front wall • 2" king pin • Galvanized steel front wall, approx. 400 mm high • Front galvanized connection strip with yellow-red air couplings • 2 wheel chocks with holders mounted on the front wall • Rear mount on gooseneck for ALU drive-on ramps • Galvanized extendable wideners appx. 230 mm per side • Bracket for a beacon at the rear of the trailer Fpodpfx Apema Hf Retjk • Galvanized supports under the chamfer of the loading platform • White reflector tape on the sides as per EU regulations, red at the extension and rear • Mounts for warning panels including socket left and right at the gooseneck and rear panel • Detachable ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • Rear galvanized plug-in stanchions removable (body length approx. 2,560 mm) • 3 pairs of WADER container pockets in the loading platform for a 20ft (30ft) or a 40ft container • 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform • Lifting axle on the front axle with TEBS E control according to the current axle load and loading condition • Movable mounting rails for ALU drive-on ramps at the rear of the vehicle • 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame chamfer of the loading platform • BEKAMAX (Pico) centralized lubrication system with NLGI-2 standard grease and removable pump cover • Four extendable warning panels approx. 423 x 423 mm with a position light, extendable by approx. 400 mm • Holder for beacon mounted on the warning panels • European reflector plates (red-yellow) on the rear of the trailer • 80 km/h speed limit stickers at rear and both sides • Axle load gauge with load diagram included • HRM Metallisation (High Resistance Metallisation) of the outer frame • Complete steel structure is shot-blasted, then defined visible surfaces are metallized with ZINACOR 850 (zinc 85% - aluminum 15%) using hot finishing

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. Fsdpfxorgzv Ns Aptopk GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck

Stanje: novo, največja dovoljena obremenitev: 90.700 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.850 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Fpjdpsw Tgp Defx Aptok Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: Hydraulically lift/lower and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * ATX-A lowbed with telescopic longitudinal beams in low-profile design, fixed hardwood floor approx. 50 mm thick * With drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm, ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for attaching a lowbed at the front; rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for front bogie: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLES, all axles hydro-mechanically forced-steered * Hose rupture valve on axle leveling cylinder with automatic RESET function * Hydraulic cylinders with shutoff taps and locking pins for securing in raised position * Final painting of axles with 2 coats of single color 2K paint, painted in MB7350 Novagrau * Rated axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Tires for rear bogie: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection * Final painting with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, according to RAL-System 841GL Including accessories: * Steel front wall, approx. 400 mm high * Plug-in aluminum side and rear boards on gooseneck, approx. 400 mm high, anodized * 3.5" kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on gooseneck * Front bogie with separate air connection for air impact wrench * BEKA-MAX central lubrication for one 3-axle bogie * Preparation for bolt-on container positioning for 1 x 20' or 1 x 30' on the outer beams * Without container locks * Brackets on the outer beams for installing foldable extensions * One 7-pin socket left and right, front and rear on rear bogie for warning panels * BEKA-MAX central lubrication for one 5-axle bogie * On the rear bogie, socket for cable remote control for steering * Rear bogie with trough * 2 LED reversing lights mounted on rear panel * European reflector boards (red-yellow) on the rear * One mudflap at rear * One LED beacon with bracket left and right on rear cross-member * Two INOX toolboxes 855 x 340 x 390 mm on gooseneck, left and right * 1-circuit...

Stanje: novo, največja dovoljena obremenitev: 50.400 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment specification. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. length 3,700 mm, with rear bevel of approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches * 1 pair of detachable ALU side walls, approx. 400 mm high, anodized finish * 1 detachable ALU rear wall, approx. 400 mm high, anodized finish * Over the gooseneck, approx. 40 mm thick hardwood flooring, over the king pin with checker plate covering * 2-inch king pin * Mount at the rear of the gooseneck for ALU drive-on ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOAD PLATFORM * Extendable load platform, approx. length 8,800 mm, with rear bevel approx. 500 mm x 10° * Recess in platform and rear bevel for accommodating an excavator dipper stick, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reversing lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B - static test load = approx. 50,000 kg * Platform with continuous and between-axles interrupted 50 mm thick hardwood flooring (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section Fedjtx Nwnjpfx Aptjpk * Extendable galvanized side extensions by approx. 230 mm each side (without wooden planks) * Wheel wells with square climbing strips, approx. 15 x 15 mm in front of the axles, continuous opening up to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel wells with square climbing strips, approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * ALU covers for the wheel wells, usable as bridging elements for the extension OR as width extension planks * Lockable aluminium elements on the extension tubes of the side extensions * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with single-track monitoring of the axles, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, type: DR-15/60-900-4350-KG-HV-M, approx. length 4,350 mm and width approx. 900 mm * Hydraulically folding ramp tips * Ramps hydraulically adjustable individually by approx. 235 mm outward and approx. 215 mm inward * Super Grip rubber surface approx. 25 mm and steel surface approx. 5 mm as additional

Stanje: novo, največja dovoljena obremenitev: 48.300 kg, skupna masa: 71.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete vehicle inventory, including vehicles available immediately and at short notice, can be found on our website. Below is an excerpt from the equipment list. Full specification available upon request. GOOSENECK: * Gooseneck with integrated single-axle running gear (pendulum axle) in a detachable version * Gooseneck hydraulically liftable and lowerable, including hydraulic connection linked to the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with front tapering approx. 60° * Fifth wheel load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Steel front wall, plug-in type, approx. 400 mm high, with beveled design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside the front wall of the gooseneck with jib * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings on the outer frame of the running gear at the front, foldable outward (LC 10,000 daN) * 1 pair of lashing rings at the transition from running gear to loading platform (LC 10,600 daN) Fpjdpsyhkqnjfx Aptjk * On the gooseneck 1 pair of removable aluminum drop sides, approx. 400 mm high, anodized * On the gooseneck 1 removable aluminum rear wall, approx. 400 mm high, anodized * 3.5 inch kingpin * TPMS tire pressure monitoring system according to ECE R 141 * Round NATO socket on the front connector panel (Maeler & Kaege VG 96 917) * 1 stainless steel toolbox with 1 lid, mounted on the gooseneck on the right in the direction of travel by the aluminum drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING PLATFORM: * Low-bed with external beams, designed as a telescopic loading platform in low-profile design with front extension including fixed approx. 50 mm thick hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical bolt-lug coupling from low-bed to running gear for swapping the loading platform or installing extension beams * One locking position approx. every 500 mm on the extension * 4 pairs of recessed lashing rings fitted flat in the loading platform along the outer frame/external beams (LC 10,000 daN) * 1 lashing ring each on the left and right outer rear cross member (LC 10,000 daN) * Foldable extensions, approx. 230 mm per side (WITHOUT wooden boards) * Loose extension planks, steel-rimmed * Preparation for installation of bolted container positions for 1x 20’ or 1x 40’ container on the outer beams. Without container locks * 6 pairs of threaded blocks between the lashing rings under the top chord of the outer beam for mounting bolted M24 rings (LC 8,000 daN) * 2 pairs M24 bolt rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed outer frame, checker plate decking and continuous prism-shaped excavator trough, approx. 1,450 x 900 x 505 mm, open at the rear * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and foreplugs to secure in raised position * Final paint of axles in 2 layers of 2-component paint, single color, DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF, brand at our choice * Remote steering from front and rear via cable control, with axle alignment check, no installation in the tractor unit * 4 pairs of hanging la

Stanje: rabljeno, številka stroja/vozila: ***YAMT13XX6K0104043, konfiguracija osi: 3 osi, prva registracija: 01/2019, skupna dolžina: 13.800 mm, skupna širina: 2.550 mm, skupna višina: 3.410 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: drugo, Leto izdelave: 2019, Chassis Chassis height: 87 cm Kingpin / Fifth wheel diameter: 2 inches Height of kingpin / drawbar: 120 cm Special transport 2-piece road plates: ✓ Hydraulic ramps: ✓ Loading deck length: 930 cm Ramp length: 395 cm Gooseneck length: 415 cm Low loader: ✓ Maximum width: 300 cm (25 cm per side) Max. length: 1380 cm Extendable: ✓ Tank Fuel: ✓ = Further Information = Axle configuration Tyre size: 235/75 R17.5 Axle brand: Saf Brakes: Drum brakes Suspension: Air suspension Axle 1: Twin tyres; Tyre tread left outer: 60%; Tyre tread right outer: 60% Axle 2: Twin tyres; Tyre tread left outer: 20%; Tyre tread right outer: 30% Axle 3: Twin tyres; Steering; Tyre tread left outer: 55%; Tyre tread right outer: 50% Weights Unladen weight: 10,040 kg Payload: 30,960 kg Gross vehicle weight: 41,000 kg Fpsdpfx Apju H D R Eetsk Functional Body make: Faymonville Loading platform height: 87 cm Identification Registration number: C505325 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Stanje: rabljeno, konfiguracija osi: 3 osi, prva registracija: 06/2022, prostornina tovornega prostora: 23 m³, Oprema: ABS, Kempf 3-osna prikolica, Hardox, 23 m³, aluminijasta platišča, dvižna os, električno pomično nadstrešek Na kratko: · Prva registracija: 10.06.2022 · Barva: Rumena · Barva ponjave: Modra · Lastna teža: 6.140 kg · Pnevmatike: 385/65 R 22,5 · Opomba: Takoj na voljo Posebna oprema: · Trioosna prikolica s kipno nadgradnjo · Električno pomični nadstrešek Caramaro · 23 m³ Fedpfezth Nwox Aptepk · Dvižna os · BPW osi · Aluminijasta platišča (Alcoa Dura-bright) · 4 x LED vzvratne luči · Aluminijasta lestev · Vibrirajoče dno · Samodejno spuščanje pri kipanju · Nosilec za lestev + lestev · Nosilec za metlo in lopato + metla in lopata · Aluminijaste podpore · 2 kavlja za zaklepanje · Hidravlični cilinder · Bobnaste zavore · 1 x 15-polni + 2 x 7-polni električni priključek · 3 x orodjarna omara · Konturna označitev · A nalepka · Zaščita pod vozilom, zložljiva Serijska oprema: · 2 klini z nosilcem · ABS · EBS · Zračna vzmetitev · Naprava za dvig in spuščanje Pridržujemo si pravico do sprememb, napak in vmesne prodaje. Prodajalec si pridržuje pravico, da odstopi od prodaje. Avtorske pravice: Vse besedilo, slike in videoposnetki v tej oglasu so avtorska last STARENT Truck & Trailer GmbH. Uporaba, razmnoževanje ali nadaljnja distribucija – tudi delna – brez izrecnega pisnega soglasja ni dovoljena. _____ Interna številka za povpraševanja: TR26226 _____ STARENT Truck & Trailer GmbH, Bruck 49, A - 4722 Peuerbach Kontaktne osebe za prodajo: Ing. Wimmer Christoph (nemščina, angleščina, češčina, poljščina, italijanščina) p: WhatsApp t: @: Mehmet Terzi (nemščina, turščina, angleščina, ruščina, ukrajinščina, bošnjaščina, srbščina) p: / WhatsApp t: -104 @: Elias Höfler (nemščina, angleščina, bolgarščina, bošnjaščina, srbščina) p: / WhatsApp t: -123 @: Govorimo 13 jezikov. Zagotovo tudi vaš. Kontaktirajte nas! Spletna stran: / Facebook: / Instagram: / Starent Truck & Trailer GmbH odkupuje vaša gospodarska vozila, kot so tovornjaki, prikolice, tovornjaki in kombiji. Kontaktne osebe za odkup: Michael Doblhofer (nemščina, angleščina) p: WhatsApp t: -102 @: Bastian Wagner (nemščina, angleščina) p: WhatsApp t: -103 @:

Stanje: novo, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, vzmetenje: zrak, velikost pnevmatike: 235 / 75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Ojačana izvedba, zračno vzmetenje z dvižno osjo, merilnik osi za obremenitev osi, dolžina visokega ležišča približno 4.400 mm vključno z naklonom, dolžina nizkega ležišča približno 8.500 mm, višina nakladanja približno 900 mm, za 2- in 3-osno vlačilno vozilo, sprednja stena približno 800 mm visoka, 16 x žepov za kol, v zunanjem okviru, 32 x pritrdilnih ušes, rampa približno 3.100 mm dolga, rampe za prevoz čez labodji vrat, -- pridržujemo si pravico do tiskarskih napak, napak in sprememb, vzorčne slike --, Več podatkov na: !, Dodatne informacije: ! Fpodpfoztqvtex Aptjk

Stanje: rabljeno, prevoženi kilometri: 130.100 km, moč: 368 kW (500,34 KM), prva registracija: 01/2018, vrsta goriva: dizel, lastna masa: 11.725 kg, največja dovoljena obremenitev: 14.275 kg, skupna masa: 26.000 kg, velikost pnevmatike: 315/80R22,5 156/L, konfiguracija osi: 3 osi, medosna razdalja: 4.800 mm, naslednji pregled (TÜV): 08/2026, gorivo: dizel, zavore: intarder, barva: drugo, voznikova kabina: spalna kabina, vrsta prenosa: samodejen, emisijski razred: Euro 6, vzmetenje: jeklo-zrak, velikost sprednje pnevmatike: 315/80R22,5 156/L, velikost zadnje pnevmatike: 315/80R22,5 /150K, Oprema: ABS, klimatska naprava, navigacijski sistem, spojka prikolice, tempomat, zapora diferenciala, zavorni sistem na stisnjen zrak, Meiler odklopni priklopnik, tip: RS 21.67, -- pridržane pravice do tiskarskih napak, napak in sprememb, ilustrativne slike --, več podatkov najdete tukaj: !, več podrobnosti: ! Fpjdpfx Ajztnwzjptsk

Stanje: novo, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.200 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Overall loading area length approx. 8,200 mm, low bed approx. 6,000 mm long, loaded loading height approx. 890 mm, 22 lashing rings each rated at 10 t, 10 stake pockets in the outer frame, loading ramps (approx. 3,100 x 750 mm), serrated bar on the outer side of the ramps and rear slope, loading ramps laterally adjustable, 68 mm thick wooden flooring, storage box with lid for lashing chains or tension belts, contour marking according to regulations, beacon, chassis hot-dip galvanized, incl. axle load indicators, surcharge for: warning signs with lighting and beacon, widening to 3 m with timber, price: €500, hydraulic lateral adjustment of ramps, price: €1,000, rear excavator arm recess, price: €1,000 net. -- Subject to typesetting errors, mistakes, and prior sale; sample photos -- For more data, see: ! More details: ! Fpjdpfoztnwbsx Aptsk

Stanje: novo, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.000 mm, širina tovornega prostora: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Višina nalagalne površine pribl. 940 mm, 20 pritrditvenih ušes po 6 t, 20 pritrditvenih zank po 6 t, 18 pritrdilnih lukenj, 7 središčnih odprtin za kole, 14 odprtin za kole v zunanjem okvirju, 2 para kontejnerskih zapahov, Doplačilo za sprednjo steno pribl. 1.600 mm visoko, snemljiva Cena: 1.500 €, Doplačilo za izvlečno vlečno kljuko Cena: 1.500 €, Doplačilo za 4 opozorilne table z razsvetljavo Cena: 800 €, Na voljo tudi z dolžino nakladalne površine 8.600 mm, 9.000 mm ali 10.500 mm! -- Napake pri tisku, napake in spremembe pridržane, slike so vzorčne -- Več podatkov na zahtevo! Fsdjztnumjpfx Aptepk

Stanje: novo, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 10.500 mm, širina tovornega prostora: 2.550 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75 R 17,5, velikost zadnje pnevmatike: 235/75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Višina nakladalne površine obremenjena cca 940 mm, 20 x pritrdilnih obročev po 6 t, 20 x pritrdilnih oklepajev po 6 t, 18 x pritrdilnih lukenj, 7 x žepov za stebre na sredini, 14 x žepov za stebre v zunanjem okviru, 2 para zapiral za kontejnerje, doplačilo za sprednjo steno cca 1.600 mm visoko, snemljivo Cena: 1.500 €, doplačilo za izvlečno vlečno kljuko Cena: 1.000 €, doplačilo za 4 opozorilne table z osvetlitvijo Cena: 800 €, na voljo tudi z dolžino nakladalne površine 8.600 mm, 9.000 mm ali 10.000 mm!, -- Pridržujemo si pravico do tiskarskih napak, sprememb in zamenjav, slikovni primeri --, Več podatkov na zahtevo! Fpedpfx Apsztnr Ejtjk

Stanje: novo, skupna masa: 30.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.200 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 R 17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235 / 75 R 17,5, velikost zadnje pnevmatike: 235 / 75 R 17,5, voznikova kabina: drugo, emisijski razred: noben, gorivo: biodizel, Oprema: ABS, zavorni sistem na stisnjen zrak, Ladeflächenlänge Gesamt ca: 8.200 mm, Tiefbett ca: 6.000 mm lang, Ladehöhe bel. ca. 890 mm, 22 x Zurrösen je 10 t, 10 x Rungentaschen im Aussenrahmen, Auffahrrampen (ca. 3.100 x 750 mm), Kletterleiste Aussenseite an der Rampen und Heckschräge, Auffahrrampen seitlich verstellbar, Holzboden 68 mm stark, Staukiste mit Deckel für Zurrketten oder Spanngurte, Konturmarkierung nach Vorschrift, Rundumleuchte, Fahrzeug Tauchbad- Feuerverzinkt, incl. Achslastanzeigen, Aufpreis für: Warntafeln mit Beleuchtung und Rundumleuchte, Verbreiterung auf 3 m mit Holzer, Preis: 500 €, Hydraulische Verschiebung der Rampen, Preis: 1.000 €, Baggerstiehlmulde, Preis: 1.000 € netto, -- Druckfehler, Irrtümer und Änderungen vorbehalten, Muster- Bilder--, Mehr Daten unter: !, More Details: ! Fedpfx Apjztfayetspk

Stanje: rabljeno, lastna masa: 6.140 kg, največja dovoljena obremenitev: 36.860 kg, skupna masa: 43.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2019, vzmetenje: zrak, velikost pnevmatike: 235/75R17,5, barva: drugo, vrsta prenosa: drugo, velikost sprednje pnevmatike: 235/75R17,5, velikost zadnje pnevmatike: 235/75R17,5, voznikova kabina: drugo, emisijski razred: noben, Oprema: ABS, zavorni sistem na stisnjen zrak, 8 x kontejnerskih zapiral, odprtine za stebre, pritrdilne ušesce, doplačilo za rampe: 1.500 €; vozilo je ponujeno po naročilu stranke; -- napake pri tisku, napake in spremembe so pridržane, vzorčne slike --, več podatkov na: !, več podrobnosti: ! Fpedpfsztfaaox Aptok