Odprta prikolica s ponjavo

Wiese Tandemanhänger

Stanje: novo, lastna masa: 11.000 kg, največja dovoljena obremenitev: 27.000 kg, skupna masa: 38.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.300 mm, širina tovornega prostora: 2.550 mm, velikost pnevmatike: 235/75 R17.5, barva: siv, obratovalna teža: 11.000 kg, Oprema: ABS, Chassis: - Welded steel frame construction with front and rear frame cranks and a lowered bed without rear chamfer - Neck and kingpin plate 225 mm - Lowered bed rated for 25 t point load over 5 m - Outer frame closed to the outside with welded-on lashing rings for securing - Interchangeable 2" king pin - Rear hook-in rail for aluminum ramps Axles and Tyres: - BPW low-loader axles, each with a 10 t axle load, air bellows diameter 360 mm - Air suspension with lifting and lowering function, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights +100 mm - S-cam brakes 300/200 mm, asbestos-free brake pads - Automatic slack adjusters - IVTM tyre pressure monitoring - 9 tyres 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically forced steered via fifth wheel coupling Floor: - Multi-layer bonded board floor, 27 mm thick, flush with outer frame and longitudinal beams - Underside reinforced with GRP coating - 12 pairs of lashing rings welded in outer frame (8 pairs RUD 8 t – 6 pairs in the lowered bed as well as one pair each on the gooseneck and at the front of the rear aggregate – 2 pairs of 4 t lashing rings on gooseneck and rear aggregate) - 6 pairs of mushroom anchors in outer frame in the lowered bed - Storage box with lid in the lowered bed floor, front left and right Front Wall: - 25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Tarpaulin curtains on both sides with integrated vertical and horizontal belts (approx. 600 mm spacing) and stainless steel tension locks - Adjustable tarp straps (overcentre) up to loading width 4,000 mm including tarpaulin extension with press studs and Velcro fastener - Tarp extension in driving direction: 300 mm, in height: 750 mm - Incl. eyelets for separate tarpaulin extension piece - 1 pair of vertical tarpaulin pockets approx. 1,000 mm long, positioned in the lowered bed at the front crank - With belt pockets Rear Wall: - Steel rear portal frame with side tarpaulin hook-in device - Aluminum double-wing door, 25 mm thick - Both door wings fully foldable with door holders - Each door wing with aluminum double-joint hinge and two recessed grip hollows Front Corner Posts: - Roof height, bolted to front side Central Posts: - 3 pairs of infinitely adjustable folding posts - Posts are movable along the entire length via trolley - Middle posts in the lowered bed also fixable at the rear platform Roof: - EDSCHA sliding roof (galvanized) with cross beams movable in both directions (stacked forward inside the cargo area) - Rear portal cross beam swivels away - PVC tarpaulin roof without customs closure - Manually operated hydraulic lifting roof on both sides, lift 450 mm Klodpfx Ahoiu Eu Nskor - Movable lifting roof in positions front (9x50) and rear (9x50), can be driven at increased height - Including tarpaulin extension and apron at rear - Roof can be cranked out 900 mm at front wall Accessories: - Extendable warning signs (removable at front and rear, with socket) incl. position lights up to loading width 4,000 mm - Storage for 4 warning signs on inside of front wall, top right and left - 1 aluminum ladder with holder 2,500 mm long on front wall - 2 rows of self-securing aluminum slats - Metal mudguards with splash flaps - 1 overnight parking plate and 1 ADR plate on rear wall - BEKAMAX central lubrication system with pump and grease class 2 for approx. 35 lubrication points - Electrohydraul

Stanje: novo, lastna masa: 10.350 kg, največja dovoljena obremenitev: 39.150 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading area: - Telescopic loading area with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - 3-piece detachable galvanized covers over the wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the chamfer and protruding into the loading area for the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of foldable external lashing rings (LC 5,000 daN) - 2 pairs of foldable external lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece aluminum ramps: - 1 pair one-piece ALU ramps, approx. 2,500 x 600 mm - Ramp with spring lifting mechanism and manually adjustable - Maximum load per pair: 24,000 kg Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 trailing steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool - Tyres 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R 141 Accessories included: - 1 spare wheel with holder in front of the bulkhead - 2" kingpin - 1 galvanized steel front wall approx. 400 mm high - At the galvanized coupling rail at the front, yellow-red air couplings - 4 wheel chocks with holder at the bulkhead - Mounting point at the rear of the gooseneck for ALU ramps - Galvanized extensions, extendable by approx. 230 mm per side - Galvanized folding supports under the chamfer of the loading area - 1 holder for a rotating beacon at the rear of the trailer - White reflective tape laterally, at the extension, and red at the rear, per EU regulations - At the gooseneck and rear panel, left and right, each with a holder for warning signs including socket - On the gooseneck, plug-in ALU sideboards and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - 1 removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing strips every 200 mm on the outer frame in the chamfer of the loading area - Anti-slip sand coating on the checker plates on the gooseneck and the loading area Kljdpeiu Er Aofx Ahksr - Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with position light - Holder for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for determining axle loads including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces metalized and hot-finished with ZINACOR 850 (Zinc 85% – Alu 15%)