Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Multimax Plus Satteltieflader Hebebett

Stanje: rabljeno, največja dovoljena obremenitev: 35.600 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, prva registracija: 07/2025, naslednji pregled (TÜV): 07/2027, Oprema: ABS, Izpis opreme "Labodji vrat" * v obliki SNT, zasnovan za optimizacijo dolžine tovornega prostora, * dolžina približno 3.700 mm, zadnji del "labodjega vratu" s poševnostjo približno 1.000 mm x 6° * največja tehnična obremenitev sedla: 18.000 kg. Za SZM (tovorno vozilo z več osmi): 4 x 2 in 6 x 2 Tovorni prostor * teleskopski tovorni prostor, dolžina približno 9.600 mm * s poševnostjo zadaj približno 900 mm x 6° * tovorni prostor se za "labodjim vratom" hidravlično dviguje in spušča * dolžina približno 3.000 mm * nosilnost do približno 9.000 kg Rampe * DR-10-900-4920-GR-HV-AXS * par dvodelnih jeklenih ramp AXS, dolžina približno 4.920 mm in širina približno 900 mm * odprta rešetkasta površina * hidravlično odpirajoče se konice ramp Hedszkx Hbspfx Acnot * rampe se posamično hidravlično premikajo približno 235 mm navzven in približno 365 mm navznoter * največja obremenitev in kot naklona glede na tehnično specifikacijo: C470319 * največji kot naklona pri spuščenem tovarnem prostoru: približno 9° Osi in vzmetenje * BPW osi in vzmetenje, 1. in 2. os trdni, 3. os z vodenim zglobom * tehnična obremenitev osi: 12.000 kg * elektromagnetna blokada za vožnjo vzvratno, aktivira se preko vzvratne prestave in ročno * zračno vzmetenje z ventilom za dvig in spuščanje * orodje za os Zavorna sistem * znamke WABCO EBS-E, v skladu z EU predpisi * brez priključnih kablov do vlečne enote Pnevmatike * 235/75 R 17.5 3PMSF, dvojne pnevmatike, proizvajalec po naši izbiri, indeks obremenitve 143/141J (144/144F) Barvanje * 6-plastna končna obdelava: celotna jeklena konstrukcija po varjenju peskana * 1 plast temeljne barve na cinkovi osnovi * 1 plast adhezijskega prajmerja * končno barvanje z 2 plastmi dvokomponentne barve (akril), enobarvno v barvi RAL 3002, karminsko rdeča * zatem zapiranje votlin s posebnim voskom * platišča v srebrni barvi. Večbarvno in posebno barvanje na voljo proti doplačilu Dodatna oprema vključena * ASPÖCK-UNIBOX na priključni letev spredaj z vtičnicami 24N, 24S & 15-polna 24N * priklop v skladu z ISO-1185, 24S priklop v skladu z ISO-3731, 15-polni priklop v skladu z ISO-12098 * 3 kW električni hidravlični agregat za upravljanje hidravličnih operacij, razen hidravličnih vitlov * parkirni položaj na "labodjem vratu" za opozorilne table, ko niso v uporabi * zunanji nosilci "labodjega vratu" z luknjami za pritrditev vijačnih pritrdilnih obročev * prva luknja približno 200 mm od spredaj, nato približno vsakih 400 mm * ena luknja za pritrditev v zgornjem zadnjem delu zunanjih nosilcev "labodjega vratu" za vijačni pritrdilni obroč * 1 par vijačnih pritrdilnih obročev, vključen (nosilnost 10.000 daN) * 3 pari vgrajenih pritrdilnih obročev na notranji strani zunanjega nosilca "labodjega vratu" (nosilnost 5.000 daN) * 3 pari vgrajenih pritrdilnih obročev na sredini "labodjega vratu" (nosilnost 5.000 daN) * 1 par vgrajenih pritrdilnih obročev zadaj na sredini "labodjega vratu" (nosilnost 5.000 daN) * na "labodjem vratu" in zadnji poševnini rešetkasta površina z ojačitvijo s pločevino, debeline približno 5 mm * 2-palčni kraljevi zatič - vodilna plošča "labodjega vratu" za priklopno ploščo, širina približno 500 mm * mehanske podpore sedla z 2-stopenjsko prestavo in ročico. JOST modul B, statična testna obremenitev = 50.000 kg * neprekinjena rešetkasta površina z 5 mm debelo podlago kot dodatna ojačitev, zasnovana za točkovno obremenitev. Zaklepanje tovarnega prostora s konično varjenimi profilami za zaklepanje, na prvih približno 3.000 mm * na vsakih 500 mm ena točk

Stanje: novo, lastna masa: 10.700 kg, največja dovoljena obremenitev: 38.800 kg, skupna masa: 49.500 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 r 17,5, barva: sivo-črna, Oprema: ABS, Gooseneck: • Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood flooring Extendable loading platform: • Loading platform in extendable design with rear taper approx. 1,000 mm x 8° • Cut-outs in outer frame of loading platform for attaching tensioning straps • Approx. 48 mm thick hardwood flooring; anti-slip checker plate covering above the axles Two-piece steel ramps: • One pair of galvanized, two-piece steel ramps with approx. 48 mm thick hardwood covering • Ramps with hydraulically foldable ramp sections, hydraulic lift system, and hydraulically adjustable • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear or manually • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Paintwork: • First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by two-component zinc dust primer • High-quality, single-color top coat in MB 7350 Novagrey applied with two-component paint • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: • Steel construction made of high-strength fine-grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system in accordance with EU regulations, 24 Volt lighting • ASPÖCK-UNIBOX on front connection panel with 24N, 24S & 15-pin sockets Accessories included: • One spare wheel with holder • Galvanized steel front wall approx. 400 mm high • Yellow-red air couplings on the galvanized front connection panel • 4 wheel chocks • Rear mounting bracket for beacon light at the end of the semitrailer • Recess at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the loading platform taper • Cover plates to bridge the gap between ramps and loading platform • White reflector tape per EU regulations on sides, extension, and red at rear • Electro-hydraulic unit at rear, under the loading platform • On gooseneck and ramps, left and right, each with a holder for warning signs, including socket • Operating valves for the ramps located on the right side of the trailer • ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm • The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) • Four warning panels extendable by approx. 400 mm with a position light • 3 pairs of WADER container pockets in the loading platform for one 20ft, 30ft or 40ft container • 6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading platform Hjdpfjhlz S Nox Acnst • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the platform taper • Painted anti-slip sand layer on checker plates, above king pin and loading platform • Load gauge for axle load measurement, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized and hot-finished with ZINACOR 850 (Zinc 85% - Alu 15%)

Stanje: novo, največja dovoljena obremenitev: 36.400 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete range of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment. Full specification available upon request. - Gooseneck in SNT design to optimize the platform length, approx. 3,700 mm long, rear with a chamfer of approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S, & 15-pin sockets - 3 kW electro-hydraulic power pack to control hydraulic functions, except for hydraulic winches. Without installation of supply connections on the tractor unit - Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then every approx. 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper section of the outer beams of the gooseneck for a bolted lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the outer beam of the gooseneck (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) Hodjyhkquopfx Acnot - The gooseneck and rear chamfer feature grating flooring with 5 mm steel reinforcement - 2-inch king pin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable to supply the electro-hydraulic power pack and/or the electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) - On the gooseneck: 1 pair of detachable aluminum side walls, approx. 400 mm high, anodized finish LOAD PLATFORM: - Load area, approx. 9,600 mm long, with rear chamfer approx. 900 mm x 6° - Loading platform behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg - TPMS tire pressure monitoring system according to ECE R 141 - BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle steered. 3rd axle with electro-magnetic reverse lock activated via reverse gear and manually - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand at our discretion, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel underlay as additional reinforcement, designed for point loads: - on the lift bed - on the load platform - Painted sand coating on the cover plates of the gooseneck as well as transition areas between gooseneck and lift bed, lift bed and load platform, and between load platform and ramps - 1 spare wheel mounting bracket under the load platform, right side before the axles - Cutouts in the outer frame of the platform and lift bed for hooking in tension belts (LC 2,000 daN) - 11 pairs of recessed lashing rings in the outer frame of the platform, foldable outward (LC 10,000 daN): - 3 pairs in the outer frame of the lift bed - 8 pairs in the outer frame of the platform - 11 pairs of recessed lashing rings along the central girder (LC 5,000 daN): - 3 pairs in the lift bed - 8 pairs in the rear part of the platform - Control valves for the hydraulic ramps on the right side of the vehicle - 1 pair of foldable mechanical rear supports with one-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a...