Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE

Stanje: novo, največja dovoljena obremenitev: 73.540 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, Oprema: ABS, Our complete vehicle inventory, including immediately and short-term available vehicles, can be found on our website. Excerpt from the equipment specification. Full equipment details available upon request. Gooseneck: * Hydraulically liftable/lowerable and detachable gooseneck, length approx. 3,650 mm * 2 pairs of fold-out lashing rings on the exterior (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center of the gooseneck (LC 10,600 daN) * Suitable for tractor units 6 x 4 or 8 x 4, 2-axle Compact front bogie: * Hook coupling front and rear, length approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: * Telescopic excavator deck with drive-over deck hooks at the front and pin-eye coupling at the rear * Base width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear bogie: * Mechanical pin-eye coupling at the front for connecting a low-bed trailer * Rear end cross member, bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Oscillating axles, all axles hydro-mechanically forced-steered * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: 8 x (manufacturer’s choice; M+S) 285/70 R19.5 * Rear bogie: 16 x (manufacturer’s choice; M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel structure automatically shot-blasted after welding using a turbine blasting unit. Second abrasive blasting with corundum for optimum coating adhesion * Full chassis HRM-metalized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final coating in 2 layers of 2-component top coat, single color in RAL 3002 carmine red, according to RAL 841GL system Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU side panels and rear wall on the gooseneck, approx. 400 mm high, anodized finish Rsdoxbmplopfx Ab Iju * 3.5-inch kingpin * Truck hydraulic connection with flow controller (20 l/min) * Overhead support for supply lines; tractor unit tank must hold at least 80 l * With MAX Trailer coupling pieces; otherwise, couplings to be supplied by the customer ex works * BEKA-MAX centralized lubrication for gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air-powered tools * BEKA-MAX centralized lubrication for 2-axle bogie with standard grease NLGI-2 * One 7-pin socket each left and right at the rear of the front bogie for warning panels * Threading option (ø approx. 40 mm) every approx. 500 mm on the outside of the top flange of the excavator deck outer tube for screw rings (LC 16,000 daN) * Foldable extensions with steel mats, width adjustable from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX centralized lubrication for 4-axle bogie with standard grease NLGI-2 * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two stainless steel toolboxes, approx. 855 x 340 x 390 mm, mounted on the gooseneck left and right * Single-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine * Operation of the rear steering, in addition to cable remote control * One LED work spotlight each left and

Stanje: novo, lastna masa: 12.900 kg, največja dovoljena obremenitev: 34.100 kg, skupna masa: 47.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.850 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 350 mm, vzmetenje: drugo, velikost pnevmatike: 245/70 R 17,5, barva: siv, obratovalna teža: 12.900 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading platform length, approx. 3,750 mm in length Rjdpfohlz R Sex Ab Ieu - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Platform: - Low-bed with external beams, extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed with fixed hardwood flooring, approx. 40 mm thick, with mechanical locking device Rear Chassis: - Rear chassis with closed outer frame, chequer plate covering, and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside - 1 pair of lashing rings recessed in the trough - 2 pairs of stake pockets for insertable stakes 100 x 50 mm in the external frame Pendulum Axle and Tyres: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and safety locking pins for securing in raised position - Axles painted with two layers of single-colour 2K paint in “FAY-Grey-34-0260” - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Accessories: - Preparation for the installation of bolt-on container locators for 1 x 20ft or 1 x 40ft container on the outer girders - 2" king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel - Yellow-red air couplers on the galvanized front connection bar - 4 wheel chocks - Remote steering from front and rear, operable via wired remote control with push buttons, with single-track alignment control - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - White reflective tape in accordance with EU regulations on sides, extension, and rear - European reflective plates (red-yellow) on the rear of the trailer - One bracket on each side of gooseneck and rear plate for warning panels, including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on outer beam for mounting screw-on RUD Rings VLBG-4 - Detachable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized insertable stakes are removable (body length approx. 2,560 mm) - Gooseneck rear upper area covered with removable cover - 5 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading area - Folding extensions, approx. 230 mm per side - 2 pairs of bolted RUD Rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the mounting hooks of the low-bed - Anti-skid sand layer painted on loading surface - 80 km/h speed stickers at rear and both sides - Spoon boom trough at rear chassis closed at rear with plug-in plate - Four extendable warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for rear axle steering in addition to cable remote, with indicator lights on receiver for alignment control - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard NLGI-2 grease - Load pressure gauge for determining axle loads - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot blasted, then all defined visible areas metallized and finished with ZINACOR 850 (zinc 85% - aluminium 15%) hot galvanizing

Stanje: novo, največja dovoljena obremenitev: 42.900 kg, skupna masa: 55.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 29.000 mm, skupna širina: 2.540 mm, Oprema: ABS, The complete inventory of vehicles, including those available for immediate and short-term delivery, can be found on our website. Extract from the equipment list. Full specifications available upon request. Loading Platform: * Gooseneck, length approx. 3,900 mm with central beam * Loading platform, double extendable, length approx. 9,300 mm * A support plate, approx. 200 mm wide, is permanently welded to the central beam * Pneumatic locking system with conical locking pin and reinforced locking positions; supply lines are protected within the extendable beams and automatically adjust to the current platform length (except for the supply of the first and second locking positions) * Technical fifth wheel load: 25,000 kg Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, all axles hydro-mechanically forced steered, mounted on turntables * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * 275/70 R 22.5 3PMSF twin tires. Brand at our discretion * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets Rsdpfx Aeyvnd Nsb Iou * 3 kW electro-hydraulic power unit for operating hydraulic functions * 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable to the outside * 1 pair of lashing rings at the king pin (LC 10,000 daN) – all other lashing rings (LC 5,000 daN) * 3 pairs of stake pockets recessed in the outer frame of the gooseneck for plug-in stakes approx. 100 x 50 mm * 1 stake pocket bar mounted transversely on the gooseneck floor for plug-in stakes approx. 100 x 50 mm * 1x at the rear of the gooseneck * 2" king pin * Mechanical landing gear with 2-speed gearbox and crank * 8 pairs of stake pockets recessed in the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm * 10 pairs of recessed lashing rings in the outer frame of the loading platform, foldable to the outside * Remote steering from the front and rear via cable remote control, with axle tracking control, no installation required in the tractor unit * Last axle with air bellows venting activated when parking brake is applied * Steel front wall, approx. 1,600 mm high, certified design according to EN12642:2016 XL * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 1 LED work light on each side at the landing gear, wired to the tractor unit connection bar * Approx. 32 mm wooden floor on the gooseneck and the loading platform * On the large-section extension tube, one locking position every approx. 500 mm * On the small-section extension tube, one locking position every approx. 1,000 mm, enabling locking at every approx. 500 mm * Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,500 daN) * 4 stake pocket bars mounted transversely on the loading platform floor for plug-in stakes approx. 100 x 50 mm * 4 wheel chocks with holder mounted under the loading platform * 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in the direction of travel * 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in the direction of travel * 1 LED work light each left and right in front of the axles, with wiring * 2 axle load gauges mounted on the left side including axle load diagram * 1st axle equipped with automatic lift axle function as well

Stanje: novo, največja dovoljena obremenitev: 96.500 kg, skupna masa: 126.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 26.900 mm, skupna širina: 2.750 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Hydraulically lift/lowerable and detachable gooseneck, approx. 3,650 mm long * For tractor units: 6x4 or 8x4 * Truck hydraulic connection with flow control (20 l/min), incl. gantry for supply line suspension; the tractor unit tank must have at least 80 l capacity Redpfxszahp Ss Ab Isu * With MAX Trailer coupling units; otherwise, coupling units to be provided ex works by the customer * Gantry with winch for spare wheel mounted at the front of the gooseneck * 3.5-inch king pin * Steel front wall approx. 400 mm high * Removable aluminium side and rear boards on the gooseneck, approx. 400 mm high, anodised finish * Control lever on the gooseneck protected by a folding cover * Operator area lighting at gooseneck, with on/off switch * One 7-pin socket each at the left and right rear of the gooseneck for warning sign * BEKA-MAX central lubrication system for one gooseneck with standard NLGI-2 grease * Hydraulic connections from the gooseneck to the low-bed via screw couplings * Access steps on the gooseneck * Four warning panels extendable by approx. 1,000 mm (approx. 423 x 423 mm) each, with one LED position lamp and bracket for beacon * Mounting adapters for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 hp) at 3,000 rpm * Hydraulic connecting lines between powerpack and connector plate at the gooseneck * One LED worklight left and right on the rear plate of the gooseneck, individually switchable * Radio remote control for: - Operating the powerpack, start/stop of diesel engine. - Operating remote steering (in addition to cable remote), with 2 LED indicator lights on receiver for single-track control. - Lift/lower gooseneck. - Lift/lower suspension of running gear 2-axle front module: * Bolt-eye coupling front and rear. Length: approx. 2,970 mm. Module width: approx. 2,750 mm * BEKA-MAX central lubrication system for 2-axle module with standard NLGI-2 grease (not connected to steering rods) * One 7-pin socket each at the left and right rear of the front module for warning signs * Platform surface with sand coating as slip protection * Yellow reflective tape in accordance with EU regulations at the sides, on the extension, and at the rear of the trailer * One 7-pin socket for warning signs, left and right on the front module, in the axle area * Extendable outriggers approx. 230 mm per side for the 2-axle module * 1 pair M42 threaded blocks between the axles of the front module * 1 pair brackets for plug-in warning panels in the stake pockets of the exterior frame of the loading area Loading platform: * 6-axle, double telescopic loading platform with bolt-eye coupling at the front and rear chamfer approx. 500 mm x 8° * Platform length: approx. 11,000 mm * Technically extendable by: approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Base width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the platform with standard NLGI-2 grease * Platform surface with sand coating as slip protection * 11 pairs of recessed lashing rings in the external frame of the loading platform, foldable outwards (LC 10,000 daN) * Permanently welded intermediate table, approx. 500 mm long * 1 pa...

Stanje: rabljeno, Leto izdelave: 2002, obratovalne ure: 11.800 h, številka stroja/vozila: NEW-12,

Stanje: rabljeno, lastna masa: 14.995 kg, največja dovoljena obremenitev: 50.805 kg, skupna masa: 65.800 kg, konfiguracija osi: 3 osi, prva registracija: 10/2023, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 900 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R17.5, barva: siv, Leto izdelave: 2023, obratovalna teža: 14.995 kg, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel, approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Extendable loading platform with rear bevel, approx. 500 mm x 8° - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 4 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) - 1 intermediate section, 250 mm - Cut-outs in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, chequer plate over the axles Axles and tyres: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle tools - Tyres 235/75 R17.5 Braking system: - Braking system according to EU regulations with EBS-E (4S3M) Accessories included: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings mounted on the galvanized connection strip at the front - 4 chocks with holders on the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power unit - Remote steering from front and rear via cable remote control with push buttons, including single-track control of the axles - Mounting for ALU ramps at the rear of the gooseneck - Hot-dip galvanized, extendable side extensions, approx. 230 mm per side - European reflector boards (red-yellow) at the rear of the trailer - White reflective tape as per EU standards on the sides, on the extension, and red at the rear - Bracket for warning signs on left/right of gooseneck and rear panel, incl. socket - Galvanized folding supports under the loading platform’s rear bevel - Holder for a beacon at the rear of the trailer - Central lubrication system with 2 BEKAMAX (Pico) pumps, NLGI-2 standard grease and removable cover for the pump - Mud flap at the rear of the trailer - Manual and documentation - On the gooseneck: insertable ALU side boards and rear wall, approx. 2,440 x 400 mm - Removable galvanized stanchions at the rear (body length approx. 2,560 mm) - 4 pairs of WADER container locks recessed in the loading platform for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 8 pairs of pockets for removable stanchions, 100 x 50 mm, in the outer frame of the loading platform - Adjustable hook rails for ALU ramps at the rear of the vehicle - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - Four warning panels, extendable approx. 400 mm, approx. 423 x 423 mm, each with position lamp - Mounting on warning panels for beacon - Radio remote control for remote steering in addition to cable remote control, with indicator lights on the receiver for single-track control - Painted-in sand layer on chequer plates, above the king pin and on the loading area for anti-slip protection - 80 km/h speed limit decal at the rear Rjdpfx Abev Hr Axe Ieu - Load pressure gauge for axle load determination, including load chart

Stanje: rabljeno, lastna masa: 13.200 kg, največja dovoljena obremenitev: 52.800 kg, skupna masa: 66.000 kg, konfiguracija osi: 3 osi, prva registracija: 06/2025, dolžina tovornega prostora: 9.300 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 245/70 R 17,5, barva: siv, Leto izdelave: 2025, Oprema: ABS, For every used semi-trailer, you will receive a current and comprehensive inspection and function report. Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable Load Area: - Extendable load area with rear chamfer approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame for attaching tension belts (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Axles and Tyres: - BPW axles and suspension, 1st axle rigid, all others hydro-mechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with raise and lower valve - Tyres 245/70 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 Two-part Steel Ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramp sections hydraulically foldable and retractable, with hydraulic lifting and shifting - Max load per pair: 40,000 kg Included Accessories: - 2'' king pin - Galvanized steel front wall approx. 400 mm high - Yellow and red air couplings to the galvanized coupling rail at the front - 4 wheel chocks - One spare wheel - Electro-hydraulic power unit - Remote steering front and rear via cable remote control with push buttons, including axle alignment monitoring - Mounting at the rear of the gooseneck for ALU approach ramps - EU reflective panels (red-yellow) at the rear of the trailer - White reflective tape on sides, extension and rear in red (per EU regulations) - At the gooseneck and ramps, left and right, holder for warning boards including socket - Holder for a rotating beacon at the rear of the trailer - Galvanized folding supports under the chamfered load area - Ramp control valves mounted on the right trailer side - Cover plates to bridge the gap between ramps and load area - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 - On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm - Rear galvanized plug-in stanchions removable (structure length approx. 2,560 mm) - INOX toolbox 1,350x400x400 mounted on the gooseneck, box covers oil filler cap - 4 pairs of WADER container lock pockets on load area, for 1x 20ft, 2x 20ft, 1x 40ft or 1x 45ft container Rjdpeyffd Djfx Ab Ieu - 7 pairs of stake pockets for 100 x 50 mm plug-in stanchions in outer frame - Galvanized, extendable platform wideners approx. 230 mm per side - Square-section climbing strips 20 x 20 mm every 200 mm on the outer frame of the chamfer - Lift axle on front axle with TEBS E control, based on axle load and loading condition - Four extendable warning signs, approx. 400 mm extension, dimensions 423 x 423 mm each with position light - Radio remote control for rear axle steering, in addition to cable remote, with signal lights for axle alignment on receiver - Anti-slip sand coating painted on checker plate surfaces of gooseneck and load area - 80 km/h speed decals rear and on both sides

Stanje: zelo dobro (rabljeno), konfiguracija osi: 2 osi, dovoljena osna obremenitev (os 1): 12.000 kg, dovoljena osna obremenitev (os 2): 12.000 kg, prva registracija: 03/2015, dolžina tovornega prostora: 134.450 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 480 mm, vzmetenje: hidravlika, Leto izdelave: 2015, Oprema: ABS, = Dodatne možnosti in oprema = - Centralno mazanje = Dodatne informacije = Konfiguracija osi Vzmetenje: hidravlično vzmetenje Zadnja os 1: Max. obremenitev osi: 12.000 kg; Krmiljena Zadnja os 2: Max. obremenitev osi: 12.000 kg; Krmiljena Teže Lastna teža: 12.660 kg Nosilnost: 34.340 kg Skupna dovoljena masa: 47.000 kg Funkcionalno Višina nakladalne površine: 48 cm Izvlečna nadgradnja: Da Stanje Tehnično stanje: zelo dobro Vizualno stanje: zelo dobro Finančne informacije Cena: Po dogovoru Dodatne informacije Rjdpfx Absvtc Ais Isu Za več informacij se obrnite na Davida F Middelmana.

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long, rear chamfer approx. 1,000 mm x 6° * For tractor units: 4 x 2 and 6 x 2 * ASPÖCK UNIBOX * On the gooseneck and rear chamfer: grating floor with 5 mm steel reinforcement * 2 inch king pin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Round NATO socket on the front connection rail (Maeler & Kaege VG 96 917) * One pair of plug-in ALU side boards on gooseneck, approx. 400 mm high, anodized finish * One LED work light each mounted top left and right on the front wall, operated by on/off switch (control via tractor unit is not possible in this case) LOADING PLATFORM: * Platform length approx. 9,600 mm, with rear chamfer approx. 900 mm x 6° * Platform behind the gooseneck hydraulically liftable/lowerable, length approx. 3,000 mm, load capacity approx. 9,000 kg * Continuous grating floor on both lift bed and platform with approx. 5 mm steel base as additional reinforcement, suitable for point loads TYRES: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steering * 3rd axle with electro-magnetic reverse lock triggered by reverse gear and manual activation * 1st axle with start assist * Technical axle load: 12,000 kg per axle * Air suspension with lift and lower valve HYDRAULIC LOADING RAMPS: * One pair of two-piece AXS steel ramps with grating surface, approx. 4,920 mm long and approx. 900 mm wide * Hydraulically folding ramp tips * Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward * Flashing lights on the outer edges of ramp tips, switch next to ramp controls * Ramp safety in road position via quick release * Painted sand coating on ramp frame and ramp tip * Mechanical drop-leg type supports on the sides of the ramps for stability when docking to unloading ramps * Ramp operation valves located on the right side of the vehicle BRAKE SYSTEM: WABCO EBS-E brake system according to EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection PAINTWORK: * Trailer in carmine red (RAL 3002) * Rims silver gray * Side boards in bare aluminum * Wheel hubs according to axle manufacturer * Lamp panel pure white (RAL 9010) EQUIPMENT: * Removable front wall made of steel, approx. 1,600 mm high, with supply line connection strip to tractor approx. 1,000 mm from bottom edge of outer frame profile * Lashing chain fixing options on the inside left and right of the front wall, including aluminum trays below left and right for storing chains or tensioning straps * Behind the front wall, approx. 12 mm thick DELIGNIT panel, bolted Rsdpfx Aoy Auhheb Ieu * 2 additional pairs of bolt-on lashing rings (LC 5,000 daN) * Electric cable winch, approx. 5,400 kg pull capacity, with radio remote control. Steel cable approx. 24 m long, cable diameter approx. 9.5 mm, including cable pressure roller

Stanje: novo, največja dovoljena obremenitev: 30.190 kg, skupna masa: 43.000 kg, konfiguracija osi: 2 osi, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. The following is an excerpt from the specifications. Complete equipment details available upon request. Load area: - Lowbed with external beams, extendable version in SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current lowbed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design to optimize load area length, approx. 3,750 mm - Gooseneck hydraulically lift/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear chassis: - Rear chassis in short version with closed outer frame and checker plate cover - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings lying flat, at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Technical axle load: 12,000 kg per axle - Air suspension with raise/lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF, manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to tractor via standardized EBS interface (ISO 11992) - For proper display, the tractor must be capable of transmitting and displaying these data Braking system: - Braking system according to EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with turn indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel construction of high-strength fine-grain steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel construction automatically shot-blasted after welding - Second blasting with corundum for optimal coating adhesion - Complete vehicle chassis coated with HRM metallization using ZINACOR 850 (85% zinc / 15% aluminium) for premium corrosion protection - Top coat with 2 layers of 2K paint in RAL 3002 carmine red, single-color, according to RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - No metallic paint possible - Paint system tested in salt spray test according to ISO 9227-NSS - Cavity sealing with special wax Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote-steered axles from front and rear via cable control with pushbuttons, with single-track monitoring (without installation in tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupler instead of threaded couplings - Electro-hydraulic power unit - Prepared for installation of bolted container mounts for 1x 20' or 1x 40' container on outer beams Rodpfx Aoxarl Nob Iju - Without container locks

Stanje: novo, lastna masa: 22.700 kg, največja dovoljena obremenitev: 79.300 kg, skupna masa: 102.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 11.000 mm, širina tovornega prostora: 2.850 mm, višina nakladalnega prostora: 920 mm, velikost pnevmatike: 245/70 R 17.5, barva: siv, obratovalna teža: 22.700 kg, Oprema: ABS, Gooseneck: - Gooseneck in SNT design to optimize load platform length, approx. 3,750 mm long, rear with chamfer approx. 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6 x 4 and 8 x 4 Load platform: - Extendable load platform, approx. 11,000 mm long with rear chamfer approx. 500 mm x 10° - Recess in the platform and into the chamfer for receiving the excavator dipper stick, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking pin and reinforced locking positions, supply lines protected within the extendable beams, automatically adapting to the actual platform length Ramps: - One pair of two-piece steel ramps approx. 4,650 mm long and 900 mm wide - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - 25 mm "Super Grip" rubber flooring and approx. 5 mm checker plate as additional reinforcement on the chamfered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - PA-X axle system, all axles hydro-mechanically forced steered - Steering performance of the first two axles can be optimally adjusted to the platform length, both mechanically and hydraulically - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-fitted locking pins for securing in raised position - 245/70 R 17.5 3PMSF Rjdpfx Absk Af Sve Iou Accessories included: - Plug-in steel front wall, approx. 400 mm high - Supply line connection strip for tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - Chequer plate covering over the gooseneck - On gooseneck: 1 pair of removable anodized ALU side walls, approx. 400 mm high - On gooseneck: 1 removable anodized ALU rear wall, approx. 400 mm high - 3.5" king pin / 2" king pin mounted - Guide plate of the gooseneck for fifth wheel plate, approx. 500 mm wide - 4 chocks - 4 axle load gauges - Mechanical drop tube supports at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical drop tube supports at the front - Continuous steel deck with baked-in sand layer as anti-slip protection on the platform - 1 intermediate table, approx. 500 mm wide, for the extension, with slotted holes for insertable and relocatable bridging elements - Sand coating on support surfaces of the intermediate table - Mechanical locking for securing the intermediate table on the extension - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widenings, approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing spotlight each on left and right rear of the vehicle - 3 kW electro-hydraulic power unit - Loose widening planks in reinforced steel U-frame - Radio and cable remote control - 4 warning signs, approx. 423 x 423 mm

Stanje: rabljeno, številka stroja/vozila: YAFSR31200001xxxx, Leto izdelave: 2012, Prosimo, navedite referenčno številko ob povpraševanju: 23457 Specifikacije: Leto modela: 2012 3 osi Dolžina: 1325 cm Lastna teža: 12.178 kg Dovoljena skupna masa: 59.000 kg 12-tonske osi Redpfx Abjy T D Sqo Iju Krmiljenje na vseh oseh Takoj na voljo Opis: 2012 Faymonville Telemax prikolica s fiksno ploščadjo z raztegljivostjo do 27 metrov. Podaljšek znaša 14 metrov. Pripravljeno za dostavo. Tehnični pregled (TÜV): Da EU odobritev do: 28.02.2027 Lastna teža: 12.178 Skupna teža: 59.000 Model: Telemax ravna prikolica z 27 m izvlekom = Dodatne informacije = Za več informacij kontaktirajte ATS Norway.

Stanje: rabljeno, skupna masa: 44.000 kg, konfiguracija osi: 2 osi, prva registracija: 04/2018, Unladen weight: 11,800 kg Width: 12,000 mm Extendable forward for front loading of coupled flatbed deck - Gooseneck in compact design - L x W: 3,900 x 2,480 mm - Interchangeable 2" king pin - Integrated hydromechanical steering - Hydraulic lifting and lowering function, incl. support cylinders - Rated for a technical fifth wheel load up to 24t - 4-sided aluminium drop sides - Steering radius: 2,200 mm Flatbed Deck - Lowbed with external tubes - Flatbed length: 6,750 mm, extendable by 5,500 mm to a total of 12,250 mm - Flatbed width: 2,550 mm - Construction height: 200 mm - Loaded deck height approx. 300 mm with 100 mm ground clearance, or approx. 350 mm with 150 mm ground clearance - Front coupling claws for connection to gooseneck 2-Axle Chassis - Chassis in compact design - Air-suspended chassis (L x W approx. 2,750 x 2,550 mm) incl. lift/lower valve, with 2 forced-steered axles, BPW make, wheelbase 1,330 mm - Chassis with wheel well Brake System - Dual-line full-wheel pneumatic brake system Rodsy U Df Hepfx Ab Ieu - Progressive central lubrication system - Radio remote control - Coupled height when loaded: 1,250 mm - Both axles with hydraulic forced steering

Stanje: novo, največja dovoljena obremenitev: 67.200 kg, skupna masa: 85.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete inventory of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment features. Full equipment details upon request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm long, with a rear chamfer approx. 1,000 mm x 10° * For tractor units: 6x2, 6x4, and short 8x4 * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish Rsdpfsrgzv Nex Ab Iju * One plug-in ALU rearboard, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring above the gooseneck, checker plate flooring above the king pin * 3.5 inch king pin * Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide * Round NATO socket on the front connection bar (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. bracket for suspension of supply lines (Faymonville couplings) * 2 pairs of stake pockets sunk into the gooseneck, for plug-in stakes approx. 100 x 50 mm LOADING DECK * Extendable loading deck, length approx. 11,000 mm, rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking bolt and reinforced lock positions, supply lines are routed protected in the extendable beams and automatically adjust to the respective platform length * BPW axles and suspension, 1st axle steerable, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Tyres: 235/75 R 17.5 3PMSF, twin tyres * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg * Continuous 50 mm thick hardwood flooring on the loading deck, interrupted between the axles (increases coefficient of friction) * Slotted holes for attachable and re-positionable bridging elements: - on the fixed section behind the gooseneck - at the front of the loading area * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate flooring, slotted holes front and rear for attachable and repositionable bridging elements * 1 pair of recessed horizontal lashing rings at the front of the fixed platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the deck, fold-out to the outside (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering operated from both front and rear via cable remote control, with axle tracking control, no installation in the tractor unit * 1st axle with automatic lift-axle function and start-up aid according to EU Directive 2021/535 * Under the gooseneck and on the rear cross member, one 7-pin socket each on left and right, with bracket for warning signs * Painted sand coating on the outer frame of the platform as well as on the checker plates of the platform and in the transition area between the loading deck

Stanje: novo, največja dovoljena obremenitev: 36.040 kg, skupna masa: 53.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, Our complete inventory of immediately and short-term available vehicles can be found on our website. Excerpt from the equipment list. Full specification available on request. Gooseneck: * Gooseneck in SNT design to optimize loading deck length, approx. 3,750 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractor units: 6 x 4 or 8 x 4 Lowbed: * Lowbed with exterior beams, extendable, SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood flooring approx. 40 mm thick and mechanical locking * Supply lines routed protected within the extendable beams, automatically adapting to the lowbed length * 7 pairs of folding lashing rings outward (LC 10,000 daN) * 6 pairs of threaded mounting blocks on the inner beam for screwable RUD rings Rear chassis: * Rear chassis with closed outer frame and tread plate cover * Chassis with excavator recess, closed in the rear half to house air tanks * 3 pairs of folding lashing rings outward (LC 5,000 daN) * 1 pair of folding lashing rings outward (LC 10,000 daN) * 1 pair of horizontal lashing rings, positioned front & rear on the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer at choice. Load index (146/146F) Braking system: * WABCO braking system according to EU regulations with EBS-E (2S2M) Coating: Rjdpfx Absy Uwu Ie Isu * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Finished with 2 coats of 2K paint, single-colored in RAL 3002 Carmine Red, per RAL System 841GL Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Remote axle steering, from front and rear, operated by cable remote control with push buttons, including axle alignment monitoring (without installation on the tractor unit) * Preparation for bolt-on container lockings to accommodate 1 x 20', 1 x 40', or 1 x 45' container on the outer rails. Without container locks * Hydraulic connections from gooseneck to lowbed with a multicoupling instead of screw couplings * Electrohydraulic unit * Spiral cable (approx. 35 mm², approx. 3.5 m in length, max. 250A) for the power supply to the electrohydraulic unit and/or the electric winch, with plug connection (NATO-NATO) between trailer and tractor unit * Yellow reflective tape according to EU regulations, on the sides, extension, and at the rear of the trailer * At the gooseneck front and rear left and right, each with a holder for warning signs, including socket * Manual and documentation on USB stick * Central lubrication system with 2 pumps BEKAMAX (Pico) with standard grease NLGI-2 and removable protection for the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer rail for mounting screwable RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above standard ride position, selectable via manual control * On the gooseneck, plug-in ALU side and rear walls approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (superstructure length approx. 2,560 mm) * Separate air connection with air gun on the gooseneck * A stainless steel toolbox, INOX, approx. 1,350 x 400 x 400 mm