Polpriklopnik z nizko nakladalno ploščadjo

FAYMONVILLE Multimax Satteltieflader (2+2) - nachlaufgelenkt

Stanje: rabljeno, največja dovoljena obremenitev: 51.870 kg, skupna masa: 65.000 kg, konfiguracija osi: 3 osi, prva registracija: 03/2025, naslednji pregled (TÜV): 03/2026, skupna širina: 2.540 mm, Oprema: ABS, Our complete stock of vehicles, including those available immediately and at short notice, can be found on our website. Extract from the equipment. Full equipment details available upon request. GOOSENECK - Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, rear with 1,000 mm x 10° bevel - Suitable for tractor units: 4x2, 6x2, and 6x4 - Removable steel front wall, approx. 400 mm high - Yellow-red air couplings on the front connector strip - ASPÖCK UNIBOX on the front connector strip with 24N, 24S, & 15-pin sockets - 3 kW electro-hydraulic unit for hydraulic control - Outer beams of the gooseneck with mounting holes for bolt-on lashing rings - One mounting hole at the upper rear of the gooseneck outer beams for a bolt-on lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - On the gooseneck, 1 pair of plug-in aluminum sideboards, approx. 400 mm high, anodized finish - On the gooseneck, one plug-in aluminum rear board, approx. 400 mm high, anodized finish - Approx. 40 mm thick hardwood flooring above the gooseneck - 2-inch kingpin - Gooseneck guide plate for fifth wheel, approx. 500 mm wide - Rear mount on gooseneck for aluminum drive-on ramps Lrjdpoxtc Uhsfx Aayog - Round NATO socket at the front connector strip (Maeler & Kaege VG 96 917) LOADING PLATFORM - Extendable loading platform, approx. 8,800 mm long, rear with 500 mm x 10° bevel - Recess in the loading platform and the bevel to accommodate excavator dipper arm, approx. 2,490 x 750 x 210/290 mm (L x W x H) - TPMS tire pressure monitoring system according to ECE R 141 - BPW axles and suspension - 1st and 2nd axles fixed, 3rd and 4th axles steering trailing axles - 3rd and 4th axles with electro-magnetic reverse lock, activating via reverse gear and manually - Technical axle load: 12,000 kg each - Air suspension with raising/lowering valve - 235/75 R 17.5 3PMSF twin tires - Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load: approx. 50,000 kg - Continuous and inter-axle interrupted approx. 50 mm thick hardwood flooring on the loading platform (increased friction coefficient) - Loading platform locking using conically welded locking profiles every approx. 250 mm - Slotted holes for attachable and repositionable bridging elements at the front of the platform - Intermediate platform with offset surface, approx. 300 mm wide, for the large cross-section sliding tube with sheet covering – front and rear with slotted holes for attachable and repositionable bridging elements – removable panel flush with the loading platform - 1 pair of lashing rings on the front cross member (LC 10,000 daN) - 6 pairs of recessed lashing rings in the outer frame, foldable outwards (LC 10,000 daN) - Additionally, 1 pair of external lashing rings on the front cross member, rotated approx. 90° inwards to the platform (LC 10,000 daN) - Extendable (galvanized) extensions, approx. 230 mm per side - 1 pair of fixed wheel recesses open up to the extension, approx. 700 x 410 mm (W x D), in the platform before the 1st axle, wheel recesses with sheet covering and square climbing strips of approx. 15 x 15 mm, each approx. 200 mm - Between 2nd and 3rd axles in the platform, 1 pair of fixed wheel recesses, approx. 1,695 x 700 x 410 mm (L x W x D); covers for wheel recesses split lengthwise, with wood overlay, external plug-in mounting

Stanje: novo, največja dovoljena obremenitev: 36.500 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full specifications available upon request. Ledpewvzg Rjfx Aaysrg * Gooseneck, approx. 4,100 mm long with central beam * Platform deck, extendable twice, approx. 9,400 mm in length * BPW axles and suspension * All axles hydro-mechanically forced steered * Technical axle load: 12,000 kg * Air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF dual mounted * WABCO brake system, EBS-E * 3 kW electro-hydraulic power unit for hydraulic operations, without installation of supply connections at the tractor unit * 4 pairs of stake pockets recessed into the outer frame of the gooseneck, for insertable stakes approx. 100 x 50 mm * 2-inch king pin * 8 pairs of stake pockets recessed into the outer frame of the platform deck, for insertable stakes approx. 100 x 50 mm * 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the deck on the left in the direction of travel * Remote steering from the front and rear via cable remote control with push buttons; with single-track axle monitoring; no installation in the tractor unit * 2 axle load gauges mounted on the left side * Steel front wall, approx. 1,600 mm high * 3 transverse stake pocket strips in the platform deck, for insertable stakes approx. 100 x 50 mm * 1 transverse stake pocket strip in the gooseneck deck, for insertable stakes approx. 100 x 50 mm * 1 additional lockable INOX toolbox under the platform deck * WADER container pockets in the platform deck for transporting: 2x 20' containers or 1x 40' container * Central lubrication system with 2 pumps, brand BEKAMAX * Complete HRM metallization (High Resistance Metallisation)

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized Lrjdpfx Aaeya E A Noyeg - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm