Polpriklopnik z nizko nakladalno ploščadjo

Schütte SAL35, Tiefbett 8,7m, 2x gelenkt, BPW

Stanje: novo, največja dovoljena obremenitev: 37.820 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment. Complete specification available on request. Gooseneck: - Gooseneck with front corners beveled approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring approx. 30 mm thick Loading Platform: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing stripes approx. 15 x 15 mm, including widenings at the bottom - Between the 1st and 2nd axles, one fixed pair of wheel recesses approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-part removable galvanized covers over the wheel recesses (W approx. 670 mm), max. point load approx. 5 t/piece - Recess in the bevel and extending into the loading platform for accommodating excavator stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of folding-out lashing rings (LC 5,000 daN) - 3 pairs of folding-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) - Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) One-Piece Steel Ramps: - 1 pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting system, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm do not need to be considered in the vehicle length in transport position Landing Gear: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load per axle: 12,000 kg - Electro-magnetic reverse lockout, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tool Tyres: - Tyres 235/75 R 17.5 3PMSF, brand of our choice - TPMS tyre monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. To display correctly, the tractor unit must be able to receive and show this data. Brake System: - WABCO brake system in compliance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Steel Construction: - Steel structure made from high-tensile fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa); S690QL/S700MC (yield strength 690MPa) Electrical System: - Electrical system in accordance with EU regulations - 24 Volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front terminal bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot blasted with a turbine blasting system after welding Isdpfx Ahsw Tpqwekjtf - Second blasting process with corundum for optimum coating adhesion - HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection - Final paint with two layers of 2K topcoat, single color in RAL 3002 Carmine Red, according to the RAL 841GL system - Rims in silver - Rear section metallized and in RAL 9010 (con...

Stanje: novo, lastna masa: 14.350 kg, največja dovoljena obremenitev: 53.450 kg, skupna masa: 67.800 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.800 mm, širina tovornega prostora: 2.540 mm, višina nakladalnega prostora: 860 mm, vzmetenje: zrak, velikost pnevmatike: 235/75 R 17,5, barva: siv, Oprema: ABS, dvižna zadnja plošča, Gooseneck: - Gooseneck in SNT design for optimization of loading bed length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading bed: - Extendable loading bed, length approx. 8,800 mm, rear chamfer approx. 500 mm x 10° - A recess in the loading bed and the chamfered section for receiving the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-part steel ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 215 mm inwards - 'Super Grip' 25 mm rubber flooring and approx. 5 mm steel plate as additional reinforcement on the rear chamfer of the loading bed - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: - BPW axles and suspension, 1st axle steering, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire sensors fitted on all wheels, including spares Surface treatment: - Complete steel structure automatically blasted with shot blasting system after welding - Second blasting with corundum for optimum coating adhesion - HRM metallization of entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K top coat, single colour in MB 7350 Novagrau Accessories included: - Plug-in steel front wall, approx. 400 mm high - 3kW electro-hydraulic power unit for controlling hydraulic functions, with the exception of hydraulic winches - 1 spare wheel - Outer carrier on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings in the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - On top of the gooseneck, approx. 40 mm thick hardwood flooring, above kingpin area with checker plate cover - 2" kingpin - Round NATO socket on front connection strip Itedpeya E A Nsfx Ahkef - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, fold-out lashing rings in the outer frame of the loading bed - Extendable (galvanized) widenings by approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, in front of the axles fully open up to gooseneck cross beam, approx. 700 x 410 mm - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for wheel recesses, which can also be used as bridging elements for the extension or as widening boards - 1 pair mechanical rear supports - Radio and cable remote control - Lift axle on front axle - Square climbing bars 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Stanje: novo, številka stroja/vozila: c78894767223a51dd199030f3, lastna masa: 4.600 kg, Further Information Frame Steel welded construction made from fine-grain steel, hot-dip galvanized, flat platform without raised edges. The loading area slopes downwards by approx. 8° after the rear axle. Longitudinal beams made from steel profiles, steel frame hot-dip galvanized, with stainless steel plate (NIRO) at the bend to guide the cable, flush with the floor. For trucks with wheelbase: 2nd axle at 1,795 mm / 2nd to 3rd axle 4,105 mm and 3rd to 4th axle 1,350 mm. Trailer Coupling Ball-type tow hitch D24.8: (height from the ground to the top edge approx. 480 mm), towing capacity 2,800 kg, including mounting and electrics with 7-pin socket. Accessories/Modifications 2 chock holders, foldable aluminum side underrun protection – taken from the truck! Steel rear underrun protection, quarter-shell mudguards with mud flaps – taken from the truck! Toolbox Plastic toolbox with drawer and shelf, W = 650 / H = 520 / D = 670 mm, lockable with a padlock (lock not included). 1 bracket for 3 jerry cans. 1 stainless steel toolbox, W = 600 / H = 400 / D = 500 mm, with polished door, lockable, includes control valve and electrohydraulic pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash water protection as far as technically possible). Electrics Adaptation of existing tail lights, 2 additional LED work lights recessed into the front wall, switched via parking lights with switch on the outside front wall left. 1 LED work light at the rear with integrated reversing camera including color flat-screen monitor with suction cup mount and power supply via 24 volts, voltage divider 24/12V, 1 seven-pin 12V socket adapter. Floor Mega Grip made from serrated, galvanized grating, steel gratings 50/4 included, with 50 mm mesh. Top side with anti-slip serration, laid continuously over the entire main platform area. Lashing Rings 12 pairs of lashing rings freely pivotable on the outer frame - each rated to 10 t. 1 at the very front and one at the very rear. 1 lashing ring at the rear center for attaching the winch cable. 12 lashing rings recessed centrally into the floor, each rated to 5 t. (not included in rear slope). Front Wall Front wall made from steel sheet, height 1,500 mm. Fixed with corner posts up to full front wall height. 2 x 12 hanging brackets for lashing chains mounted left and right on the front wall. Itsdpok Unitjfx Ahkef Winch Electric cable winch, 24 volts, pulling force approx. 6,350 kg, mounted centrally at the front wall (recessed in the loading bridge), operated via remote control, cable length min. 35 m x 9.5 mm, with roller fairlead, with cable pressure plate, including overload protection, cable freewheeling clutch, hand control with approx. 5 m cable, winch acceptance, civil engineer test report, test log, operating instructions. Loading Ramps Length 3,500 mm – 2-piece (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg per pair (also for ramp loading), electrohydraulically tiltable and laterally movable – including electrohydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle. Ramp support surface made from galvanized steel grating (like the loading bridge floor), with anti-slip serration. Ramps can be compacted to approx. 170 mm, hydraulically extendable. Ramp prepared for operation at loading dock with full load capacity. Ramp locking with 2 tension belts. Ramp tip offset (nose min. 150 mm) suitable for placement at loading ramps. Ramp operation labeled. Drop brake valve for l