Priklopnik sedeža z delovno ploščadjo

FAYMONVILLE MAX Trailer MAX200 Sattelanhänger Megatrailer

Stanje: novo, največja dovoljena obremenitev: 36.245 kg, skupna masa: 45.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory with immediately and soon available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. Loading Area: * Hardwood floor loading platform with rear chamfer approx. 1,000 mm x 8° * 2 pairs of lashing rings (LC 5,000 daN) * 1 pair of lashing rings (LC 10,000 daN) * 6 pairs of fold-out external lashing rings (LC 5,000 daN) * 2 pairs of fold-out external lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for securing strap hooks (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air suspended * Disc brakes (approx. 377 mm) * Raise/lower function (ET 120) * Axle tools Pgsdpow Tpqqsfx Af Nou Tyres: * Tyres 435/50 R 19.5 – make at our discretion * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the tractor unit via standardised EBS interface according to ISO 11992. The tractor unit must support and display these data for correct operation. Braking System: * Wabco braking system compliant with EU regulations, with EBS-E (2S2M), without connecting lines to the tractor Steel Structure: * High-strength fine-grained steel construction * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical System: * Electrical system compliant with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with indicators * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted by turbine after welding * Second shot-blasting with corundum for optimal coating adhesion * HRM metalising of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for best corrosion protection * Final coating with two layers of 2K top coat, single colour RAL 3002 Carmine Red in accordance with RAL System 841GL * Rear section metalised and painted in RAL 9010 (Pure White) * Coating system tested in salt spray test to ISO 9227-NSS * Sealing of cavities with special wax * Metallic finishes not possible Including the following additional equipment: * Yellow-red air couplings on galvanised front connection strip * 4 wheel chocks with holders * 2-inch kingpin * Loading area with heavy-duty hardwood floor * 1 spare wheel holder under the loading area, right side in direction of travel * Galvanised folding supports under the loading area rear chamfer * 9 pairs of pockets for insertable stanchions, approx. 100 x 50 mm, in the outer frame of the loading area * 1 galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * Painted sand layer on the central beam as anti-slip coating * 1 stainless steel (INOX) toolbox, transverse under the loading area, approx. 1,000 x 400 x 2,500 mm * 6 pairs of WADER container locks in the loading area, for 1x 20' container, 2x 20' container or 1x 40' container * 3 pairs of transverse stanchion rack rails installed in the loading area, for insertable stanchions approx. 100 x 50 mm * Rack for max. 9 pairs of insertable stanchions approx. 100 x 50 mm at front wall, bolted from inside * 2 stainless steel (INOX) toolboxes under the loading area left and right, approx. 600 x 350 x 600 mm * Holder for aluminium loading ramps, transverse under the loading area, behind the axles * 1 beacon li