Kögel Cargo nakup rabljenega (2)

Stanje: rabljeno, največja dovoljena obremenitev: 34.200 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, prva registracija: 05/2023, naslednji pregled (TÜV): 06/2025, dolžina tovornega prostora: 13.620 mm, širina tovornega prostora: 2.480 mm, skupna širina: 2.550 mm, Oprema: ABS, Our complete stock of vehicles, including those available immediately or at short notice, can be found on our website. Excerpt from the specification. Full specification available on request. Chassis * Regular ladder frame in lightweight steel construction with inserted cross members * Distributed load max. 30 t evenly spread over approximately 1.5 m around the payload center * Coupling plate approx. 8 mm thick, with a 2" fifth wheel kingpin according to DIN 74080 / ISO 337 * Coil well, internal length approx. 9,000 mm (shape according to VDI guideline 2700) for accommodating coils with a diameter of min. 900 mm up to max. 2,100 mm Running gear * Axle lift mechanism on axle 1 * Fully automatic axle lift control, load-dependent Starting aid * Activation by braking three times, 30% overload up to a speed of 25 km/h * Operation on the chassis via switch * Additionally possible from the driver’s cab (switch in cab required – PIN 12) Iodpfxevl N N Ts Ab Uotr Three-axle SAF INTRADISC module * With disc brakes, diameter approx. 430 mm, ET 120 * Air suspension with approx. 180 mm travel Vehicle tyres * 6 x 385/65 R 22.5, 160J * 6 steel rims 22.5 x 11.75, offset approx. 120 mm (ET 120) Chassis attachments * Mechanical landing legs with compensating foot, 24 t lifting capacity, one-sided operation on the right in the direction of travel * Spray suppression system in accordance with Regulation (EU) No. 109/2011 for three-axle module with 385/65 R22.5 tyres, consisting of 1 pair of quarter-circle mudguards ahead of the axles, 1 pair of straight mudguards with spray flaps between 1st and 2nd axle, and 1 pair of quarter-circle mudguards with spray flaps behind the axles * Side underrun protection to ECE-R73 * Holders for 8 square plug-in posts, internal dimensions approx. 340 x 220 x 2,150 mm, installed behind the axle group * 2 waterproof plastic toolboxes, internal dimensions approx. 545 x 400 x 400 mm. Mounted at the rear, 1 left and 1 right Brake / air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * Air suspension system including 1 lift/lower valve, mounted on the left in the direction of travel, behind the axle group * Driving position adjusts automatically Floor * Mounted version on both sides * Steel pallet stop rails with VarioFix hole pattern (bolted) on the left and right in the direction of travel, for internal width approx. 2,468 mm (internal loading height below outer rail is reduced by approx. 20 mm) * Laminated plywood floor, approx. 30 mm thick, with cut-out in the area of the coil well * Coil well side walls lined with plywood panels, approx. 18 mm thick * All-round jointed coil well cover made entirely of wood, with floor panels approx. 27 mm thick * Stake pockets for square plug-in posts, approx. 80 x 80 mm, arrangement according to drawing A2, 2 pairs on the longitudinal beam in 1st and 2nd position, 8 pairs in the outer frame * 8 pairs of stake pockets in the coil well for square plug-in posts approx. 80 x 80 mm, arrangement: 1st pair at the front of the well, 2nd–7th pairs as per standard drawing, 8th pair at the end of the well Superstructure * Quick-release device at front for side curtain, with tension rods and deflection lever * Quick-release device at rear for side curtain, with tension rods and ratchet * Complies with body strength according to EN 12642 XL (VDI 2700), tested for a payload of approx. 27,000 kg Rear wall * Double-wing rear portal door made of aluminium, approx. 2,630 mm internal

Stanje: rabljeno, največja dovoljena obremenitev: 34.190 kg, skupna masa: 42.000 kg, konfiguracija osi: 3 osi, prva registracija: 02/2023, naslednji pregled (TÜV): 04/2026, Oprema: ABS, You can find our complete range of vehicles, including those available for immediate and short-term delivery, on our website. Excerpt from the vehicle equipment. Complete equipment details available upon request. Chassis: * Coil trough, internal length approx. 9,000 mm (design in accordance with VDI guideline 2700) for accommodating coils with a diameter from min. 900 mm to max. 2,100 mm Running Gear: * Axle lift mechanism on axle 1 * Three-axle SAF INTRADISC aggregate, with disc brakes Ø approx. 430 mm, ET 120 * Air suspension with approx. 180 mm stroke * Tyres / Tyres: 6 x 385/65 R 22.5, 160J – brand of our choice * 6 steel rims 22.5 x 11.75, offset approx. 120 mm (ET 120) * Brake / air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS connector ISO 7638 (without connection cables) * Parking brake as spring-loaded brake, external pneumatic connectors and external EBS diagnostic port via ISO 7638 connector * WABCO EBS system * Air suspension system incl. 1 raise/lower valve, mounted on the left in the direction of travel behind the axle aggregate * Driving position self-adjusting Floor: * Fitted version on both sides * Steel pallet stop with VarioFix perforated pattern (bolted), on left and right in the direction of travel, for internal width approx. 2,468 mm (loading height reduced by approx. 20 mm under outer rail) * Panel floor approx. 30 mm thick, multi-glued plywood, recess in coil trough area Itodpfsxvgqlex Ab Usr * Coil trough side walls lined with plywood panels approx. 18 mm thick * Floor sealed all around * Coil trough cover entirely made of wood, with panel flooring approx. 27 mm thick * Stake pockets for square tube stanchions approx. 80 x 80 mm * Arrangement as per drawing A2: * 2 pairs on the longitudinal beam in 1st and 2nd position * 8 pairs on the outer frame * 8 pairs of stake pockets in the coil trough for inserting square tube stanchions approx. 80x80 mm * Arrangement: 1st pair at the front of the trough * 2nd–7th pairs as per serial drawing * 8th pair at the end of the trough Body: * Meets body strength per EN 12642 XL (VDI 2700) * Tested for a payload of approx. 27,000 kg * Front wall at body height with volumetric corners made of aluminium * Riveted with aluminium hollow profiles, screwed/riveted to frame * 1 pair of lashing rings according to EN 12640 * Inner side of front wall reinforced with approx. 12 mm plywood with film-faced surface, approx. 1,250 mm high * Double-winged rear portal door made of aluminium, approx. 2,630 mm internal width * 4 integrated rod locks (2 left, 2 right) * Bolted rear corner posts made of steel, portal height, with additional impact protection up to first door hinge * Corner posts on both sides can be mechanically swung out sideways by approx. 500 mm for loading and unloading * To operate, slide roof must be moved forward and rear doors opened * 5 pairs of receiving slots for load securing at rear corner posts side wall * 3 pairs of KÖGEL sliding rings with receiving height approx. 600 mm for 5 insertable slats stacked above each other from top edge of floor. Fixed on outer frame * 5 rows of slat receptacles consisting of plug-in slat pockets on sliding rings and variable supports in the corner posts * Variable supports as spacers for insertable slats (16 pieces), located in the slat depot of sliding and corner posts (height approx. 100 mm above floor) * 4 rows of V-aluminium insert slats on the sides * VarioFix steel perforated outer frame with 3 pair