Polpriklopnik z nizko nakladalno ploščadjo

Meusburger 3-A-Semi-hydr.Ladebod.-abklappbares Heck

Stanje: rabljeno, številka stroja/vozila: 935, lastna masa: 10.500 kg, največja dovoljena obremenitev: 31.000 kg, skupna masa: 41.500 kg, konfiguracija osi: 3 osi, prva registracija: 09/2021, dolžina tovornega prostora: 9.950 mm, širina tovornega prostora: 2.550 mm, višina nakladalnega prostora: 890 mm, vzmetenje: zrak, velikost pnevmatike: 235 / 75 R 17.5, barva: siv, Leto izdelave: 2021, Oprema: ABS, With every used semi-trailer, you receive a current and complete inspection and function report. Frame: - Welded steel frame construction with front frame cranking and flat low-bed deck - Neck height 165 mm with external longitudinal beams for an extended low-bed - With Wirtgen chamfer on cranked deck approx. 850 x 65 mm - 2” king pin Lrsdpfxeywtwqo Ab Hji - Rear section support when used as a drive-on ramp Front wall: - Aluminium front wall with bevelled corners, 1,000 mm high - Interior front wall lined with aluminium tread plate 3/5 mm over the entire height and width - Mesh extension above front wall with 2 brackets for lashing chain hanging - Box for steering, electrohydraulic motor, and winch offset approx. 150 mm to the inside (steering and motor box stacked) Floor: - Grating 30/30/5 mm over the entire loading area in both low-bed and high-bed - If rear is foldable: 40/30/25/5 in the main frame - Longitudinal bearer in the direction of travel, 5 mm thick, 30 mm or 40 mm high - Grating laid over the longitudinal beams, flush with the outer frame Axles and tyres: - 3 x 10,000 kg BPW air suspension axles with S-cam brakes (300/200 mm), bellow diameter 360 mm - Rear axle is self-steering, automatically locks when reversing, and can be manually locked if required - 1st axle is a lift axle (operated via SmartBoard) - Automatic slack adjusters - Axle spacing 1,310 mm / 1,410 mm - Wabco SmartBoard with ECAS function - Air suspension with lift and lower valve - Tyres: 235 / 75 R 17.5 Foldable rear with extension: - Complete loading area behind the axle assembly can be hydraulically folded down - Drive-on ramps can be positioned on a solid concrete ramp and loaded over ramps (both with extended and retracted sections) - Load capacity of the folded rear section: - 10 t axle load (5 t wheel load) when used as a horizontal loading area - Can withstand 22 t when used as a drive-on ramp, if the rear support (underrun protection) is on the ground - Adjustable and foldable support leg - Support leg length designed for ramp loading at a ramp height of 1,100 – 1,300 mm - Operation via electro-hydraulic unit powered by NATO socket from the tractor unit - Pump unit mounted externally on the front wall via connection points - Separate radio remote control for operation of the lifting platform and foldable rear - Hydraulic controls installed in a stainless steel toolbox 500x350x400 mm, on the right side in the direction of travel before the axle assembly - Foldable rear can also be raised by approx. 60 degrees, thereby shortening the loading area by approx. 1,300 mm - Rear extension: hydraulically extending 3-piece rear section (approx. 800 mm wide each), extendable by approx. 2,000 mm, controlled via hydraulic pump unit Accessories included: - Hydraulically liftable ramp at the cranking for driving onto the high-bed across the entire vehicle width, rated for 6 t, no drive-over plate – instead, an angle piece is welded to the cranking - At the cranking: vertical scuff protection and top stop for precise positioning when raised - Ramp secured by holding valve - 9 lashing rings installed sunk upright along the center of the loading area in the direction of travel, plus 1 foldable lashing ring in front of the fifth wheel in the center - 1 pair of 8 t foldable lashing rings towards the front wall - 2 PVC toolboxes - Radio remote control for hydraulic lift/lowering functions of the lifting bed and foldable rear