Polpriklopnik z nizko nakladalno ploščadjo

GOLDHOFER 3-achs Satteltieflader mit zwei Radmulden

Brakes:

* Knorr EBS-E (electronic braking system with driving stability control RSS)
* Emergency release device for spring-loaded cylinders
* Drum brakes

----Axles:

* Load-dependent lift axle on the 1st axle incl. starting aid (forced lowering of the lift axle via TIM possible)
* Last axle is a friction-steered trailing axle (reverse steering lock via reverse gear)
* BPW Eco Max axles

Gjdpjx Uvn Hefx Affott
----Suspension:

* Air suspension with raise/lower facility

----Electrics / Lighting:

* Knorr trailer information module
* Rear-view camera
* Acoustic reversing signal
* 15-pin and 2 x 7-pin sockets
* LED lighting
* LED warning beacon

----General Attachments:

* BPW landing legs in front
* One plastic toolbox in front of each landing leg
* Mechanically spring-assisted drop-leg supports at the rear for stabilisation during loading
* Mechanically adjustable warning board packages near the landing legs and at the rear ramps

----Gooseneck:

* Floor covering made of steel plate
* Headboard 400 mm high
* In front of headboard: closed toolbox with hinged lid approx. 2,400 x 500 x 550 mm
* At the front: 90° corners and two detachable 400 mm high aluminium sideboards (approx. 3,150 mm long) on each side
* Three pairs of 5 t folding recessed lashing rings per side on the gooseneck
* 2 pairs of stake pockets
* Closed external frame with cut-outs for 1.5 t lashing straps
* Centrally 1 pair of stake pocket strips

----Low-bed/Loading Platform:

* Floor covering made of steel plate
* Closed external frame with cut-outs for 2 t lashing straps
* 6 pairs of 10 t lashing points in the external frame
* 1 pair of 10 t lashing points centrally on the loading platform behind the gooseneck and at the rear of the loading platform
* Two pairs of 100 x 50 mm stake pockets per side in the external frame

----King Pin:

* 2-inch fifth wheel king pin with secondary screw-in position

----Excavator Boom Rest:

* Approx. 3,450 x 760 mm incl. 2 t long slots for load securing
* Excavator boom recess covered by 2 hinged lids

----Wheel Wells:

* 1 pair – lower length 1,840 mm, upper length 2,840 mm – in front of the 1st axle, 390 mm deep with climbing strips in the sloped area
* 1 pair – lower 560 mm, upper 1,640 mm – between 1st and 2nd axle, 390 mm deep with climbing strips in the sloped area
* Various wheel well depths using wheel well covers (depths approx. 390 mm and 260 mm)
* ALLTEC aluminium wheel well covers “Premium” 600 mm wide

----Widening:

* Prepared for beams for 3,000 mm widening with 8 t wheel load
* Two widening beams per side fitted in the external frame for overall width of 3,000 mm

----Ramps:

* Lateral climbing strips in the rear slope
* Sliding design for easy mounting/removal of ramps
* ALLTEC VFR 120 R one-piece aluminium loading ramps approx. 2,500 x 600 mm (24 t capacity per pair)
* Mechanically adjustable sideways

----Loading Dimensions:

Gooseneck:

* Approx. 3,700 x 2,550 mm, incl. 550 mm run-up slope to low-bed

Low-bed length:

* Approx. 8,700 x 2,550 mm, incl. 550 mm run-up slope (8°) at the rear

----Loading Height:

* Approx. 855 mm

----Paintwork:

* Chassis preservation with corrosion-resistant zinc dust primer and effective cavity sealing

----Coupling Height:

* Approx. 1,220 mm

----Information:

* Subject to errors and prior sale

----Delivery Time:

* Available immediately ex Egestorf on the A7

Oglas je bil preveden samodejno, zaradi česar je morda prišlo do napak pri prevodu.