Priklopnik sedeža z delovno ploščadjo

FAYMONVILLE MAX Trailer MAX210 Telesattel

Stanje: novo, največja dovoljena obremenitev: 38.400 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available on request. Loading Platform: * Extensible loading platform with pneumatically operated locking system * Platform surface with approx. 30 mm thick wooden planks * 7 pairs of foldable lashing rings (LC 5,000 daN) * 3 pairs of foldable lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) Landing Leg: * JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Tyres: * Tyres 385/65 R 22.5 Axle: * BPW axles and suspension, all axles force-steered by hydro-mechanical system Laodpfx Aoxl Nf Dsb Ujk * Equipped with disc brakes * Technical axle load: 10,000 kg (ET 0) * Air suspension with lift and lower valve Brake System: * WABCO brake system in line with EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Paintwork: * High-quality two-component (2K) topcoat, single colour in RAL 3002 Carmine Red Accessories: * Remote steering front and rear via cable remote control with push buttons, including axle tracking control. (no installation in the tractor unit) * Electro-hydraulic power unit * 4 wheel chocks with holders on the front wall * 2-inch king pin * Galvanised connection panel at the front with yellow-red air couplings * Bracket for a rotating beacon at the rear of the trailer * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes on the outside frame of the loading platform * 1 spare wheel holder under the platform, right-hand side in direction of travel (without spare wheel) * Load pressure gauge for axle load determination including load diagram Including Special Equipment: * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks on the platform, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; when extended an additional locking point is provided for a 45' container * 4 pairs of crosswise stake pocket strips mounted in the platform, for approx. 100 x 50 mm plug-in stakes * Storage bracket for up to 9 pairs of plug-in stakes bolted to the inside of the front wall * Climbing ladder mounted on both left and right sides in the direction of travel * 1 INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted under the platform, front left * Additional INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted under the platform, left side * Platform deck with approx. 30 mm thick wooden floor, framed with omega sections * Lifting axle on the front axle with control via TEBS E * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * HRM metalizing (High Resistance Metallisation)

Stanje: novo, največja dovoljena obremenitev: 38.400 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Extract from the equipment list. Full equipment details available on request. Loading platform: * Extendable loading platform with pneumatically operated locking mechanism * Platform with approx. 30 mm thick wooden floorboards * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching lashing straps (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres 385/65 R 22.5, brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck is via the standardised EBS interface according to ISO 11992. For correct display, the truck must be capable of transmitting and displaying this data. Axle: * BPW axles and suspension * All axles hydro-mechanically force-steered * Disc brakes * Technical axle load: 10,000 kg each (ET 0) * Air suspension with raise/lower valve * Axle tools Brake system: * WABCO brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Lasdpfxew Tpr Ij Ab Uek Steel construction: * Steel construction made from high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical installation according to EU regulations * LED lighting, 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets, connections according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel construction automatically blasted after welding using a wheel blasting machine * Second blasting treatment with corundum for optimal adhesion of the coating system * Final coat with 2 layers of 2K topcoat, in a single colour RAL 3002 Carmine Red conforming to RAL system 841GL * Rims in silver grey * Rear end metallised and painted RAL 9010 (Pure White) * No metallic paint possible * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Accessories: * Remote steering from front and rear via cable remote control with push buttons, axle single-track control (without installation in the tractor unit) * Electro-hydraulic power pack * 4 wheel chocks with holders on the front bulkhead * 2-inch king pin * At the galvanised connection panel at the front, yellow-red air line couplings * At the gooseneck and rear left and right, one holder each for warning panels, including socket * 10 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the platform * One galvanised steel bulkhead (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container lock pockets in the platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container; the extension includes an additional locking point for a 45' container * 4 pairs of crosswise stanchion pocket bars in the platform, for plug-in stanchions approx. 100 x 50 mm * Storage for up to 9 pairs of plug-in stanchions bolted to the inside of the front bulkhead * Access ladder mounted front left and right in direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted at the front under the platform on the

Stanje: novo, največja dovoljena obremenitev: 34.660 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, skupna širina: 2.540 mm, Oprema: ABS, You can find our complete stock of immediately and soon available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Loading platform * Double-extendable design with pneumatically operated locking mechanism * 2 pairs of recessed lashing rings (LC 5,000 daN) * 1 pair of recessed lashing rings (LC 10,000 daN) * 7 pairs of fold-out external lashing rings (LC 5,000 daN) * 3 pairs of fold-out external lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing legs * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Tyres * 235/75 R 17.5 3PMSF Axles * BPW axles, hydro-mechanically forced steering * Air suspension with lift and lower valve Brake system * In accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * Made from high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting * Premium and durable corrosion protection for the standard shot-blasted welded frame is ensured by a 2-component (2K) zinc primer * High-quality 2-component (2K) topcoat, single-color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Including accessories * Rear and front remote steering by cable remote control with push buttons, with axle tracking control (without installation in the tractor unit) * Electro-hydraulic power pack * 4 wheel chocks with holder on the front bulkhead * 2-inch king pin * At the galvanized connection bar at the front, yellow and red air couplings * Yellow reflective tape as per EU regulations on the sides, extension, and rear of the trailer * European reflective plates (red-yellow) at the rear of the trailer * One mud flap at the rear of the trailer * Manual and documentation on USB stick * Loading platform with heavy-duty hardwood floor Laedpfx Ajk Ugacob Ujk * 10 pairs of stake pockets for plug-in stanchions (100 x 50 mm) in the outer frame of the loading platform * Mounting bracket for a rotating beacon at the rear of the trailer * Galvanized supports under the slope of the loading platform * A mounting bracket for a rotating beacon at the rear of the trailer * Mounting rail for aluminium loading ramps at the rear of the vehicle * 80 km/h speed stickers on the rear and both sides * Load gauge for determining axle loads including load diagram * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection for the pumps * Spiral cable to power the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250 A) between trailer and tractor unit with plug connection (NATO-NATO) * Anti-slip sand layer painted on central beam * 6 pairs of WADER container pockets in the loading floor, for 1 x 20' container, 2 x 20' containers or 1 x 40' container, additional locking point in the extension section for one 45' container * 5 crosswise stake pocket bars mounted in the loading floor for plug-in stanchions 100 x 50 mm * Space for up to 9 pairs of plug-in stanchions ca. 100x50 mm, inside front bulkhead * One INOX toolbox, approx. 1,500 x 390 x 810 mm, under the loading platform on both left and right in the direction of travel * Four warning signs, extendable b