Polpriklopnik z nizkim nakladalnikom

Faymonville MAX Trailer 3-Achs-Tele-Semi-Radmul.-ALU

For every used semi-trailer, you receive a current and comprehensive inspection and functionality report.

Gooseneck:
- Gooseneck with rear taper approx. 750 mm x 10°
- 3 pairs of lashing rings (LC 5,000 daN)
- 30 mm hardwood flooring

Load Area:
- Extendable load area with rear bevel approx. 1,000 mm x 8°
- 1 pair of fixed wheel wells in front of the axles, approx. 2,850 x 970 x 400 mm
- Wheel wells with 15 x 15 mm square climbing strips and widening in the lower area
- Between the 1st and 2nd axle: 1 pair of fixed wheel wells, approx. 1,610 x 970 x 400 mm
- 3-piece removable galvanized covers over the wheel wells (width: 670 mm) – max. point load 5 t each
- Recess in the slope and load area for accommodating the excavator dipper arm approx. 2,900 x 750 x 210/290 mm
- 1 pair of flat-mounted lashing rings at the front (LC 10,000 daN)
- 5 pairs of outward-folding lashing rings (LC 5,000 daN)
- 2 pairs of outward-folding lashing rings (LC 10,000 daN)
- 2 pairs of lashing rings in the excavator dipper well (LC 5,000 daN)
- Cutouts in the external frame of the load area for securing straps (LC 2,000 daN)

One-piece ALU ramps:
- 1 pair of one-piece ALU ramps approx. 2,500 x 600 mm
- Ramp with spring lift and manually movable
- Maximum load per pair: 24,000 kg

Axles and Tyres:
- BPW axles and suspension, 2 rigid axles, 1 self-steering axle
- Technical axle load: 12,000 kg
- Electromagnetic reversing lock, activated via reverse gear and manually
- Air suspension with lifting and lowering valve
- Axle tool kit
- Tyres: 235/75 R 17.5
- TPMS tyre pressure monitoring system in accordance with ECE R 141

Included Accessories:
- 1 spare wheel with holder in front of the front wall
- 2" king pin
- 1 galvanized steel front wall approx. 400 mm high
- Front galvanized connection bar with yellow-red air couplings
- 4 wheel chocks
- ALU ramp holder at rear of gooseneck
- Galvanized extensions, extendable by approx. 230 mm per side
- Galvanized folding supports under the rear slope of the load area
- 1 holder for a beacon at the rear of the trailer
- White reflector tape on sides, at extension and rear (red), in compliance with EU regulations
- Gooseneck and rear panel each with a holder for warning signs including socket
Hodpfovu T Urjx Ah Ejw
- On gooseneck: plug-in ALU sidewalls and tailboard approx. 2,440 x 400 mm
- Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm)
- 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container
- 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the load area
- 1 removable galvanized intermediate table with 1 pair of WADER container pockets
- 20 x 20 mm square climbing strips at 200 mm intervals on the outer frame of the load area slope
- Painted anti-slip sand layer on the checker plates on gooseneck and load area
- Four extendable warning plates, approx. 423 x 423 mm, extendable by approx. 400 mm, with position light
- Holder for beacon on warning plates
- Axle load gauge including load chart
- HRM metallization (High Resistance Metallisation) of the outer frame
- Complete steel construction shot-blasted, then the defined visible surfaces metallized and hot-finished with ZINACOR 850 (zinc 85% – aluminum 15%)

Oglas je bil preveden samodejno, zaradi česar je morda prišlo do napak pri prevodu.