Müller-Mitteltal Tm2 18,0 L nakup rabljenega (51.979)

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brakes * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Coupling Eye: * Drawbar with 40 mm bolted towing eye (height-adjustable) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring system ----General Attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate, safety lock pin for various support heights * Enclosed steel mudguards with spray protection * Enclosed side underrun protection usable as advertising panel * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Body: * Swiveling cable drum body, clear width between drum arms 1,700 mm, with tension lock for securing drums at the support arm ends, as well as a central claw lock to secure the cable drum body to the chassis * Motor-hydraulic drum drive with hydraulic motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter including centering and rotating ends * 1 pair of polyamide centering cones, stepwise offset ----Chassis: * Chassis made of torsion-resistant square tubes and cross beams ----Pump Unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight Dedpsu I Iqxefx Apwekp ----Paintwork: * Vehicle hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale reserved ----Delivery Time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 9.070 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.500 mm, širina tovornega prostora: 2.010 mm, višina nakladalnega prostora: 325 mm, Leto izdelave: 2026, * ETS-TA-B 11,9: * Wabco EBS (elektronski kočioni sistem) * RDÜ (nadzor pritiska u pneumaticima) * Bubanj kočnice, 2 x 5,5 t Gigant osovine * Parabolične opruge sa balans agregatom * Vučna ruda podesiva po visini oko 300 mm * BPW oslonac (nožna dizalica) * Mehaničke zadnje potpornice * Plastična kutija za alat napred desno uz čeonu stenu * Bočna zaštita od podlijetanja * LED osvetljenje * Pod od mekog drveta (nordijska jela) debljine 50 mm * U uglovima ispred čeone stene i zadnjeg nosača po 1 x 6,3 t anker, kao i sa svake strane po 2 UVV ankerska prstena od 6,3 t ugrađena u spoljašnji ram * Jednodelne mehaničke rampe od rešetkastog metala sa oprugom za upravljanje jednom osobom, dimenzija cca 2.350 x 870 mm (unutrašnje rastojanje 20 mm, rampe nisu pomične) * Čeona stena, bočne stranice, blatobrani i vučna ruda toplo pocinkovani * Osovine, opruge, vazdušni rezervoar, prednji oslonac lakirani u crnoj boji Dodpfx Apewyhzvewokp * Novo vozilo sa punom fabričkom garancijom * Zadržavamo pravo na greške i međuprodaju * Dostupno od približno 35. nedelje 2026.

Stanje: novo, največja dovoljena obremenitev: 13.830 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 4.995 mm, širina tovornega prostora: 2.380 mm, višina nakladalnega prostora: 900 mm, Leto izdelave: 2026, * KA-TA-R 18 ----Brakes: * EBS-E (electronic braking system with RSS) * Emergency release for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 9 t Gigant axles ----Suspension: * Air suspension with level control during tipping ----Electrics / Lighting: * Tire pressure monitoring system with display possibility in the truck dashboard via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting with galvanized protective cover * 2 LED reversing lights ----Drawbar eye / Drawbar: * Drawbar with 50 mm flange towing eye (adjustable by +77 mm and -33 mm using offset plate) ----General attachments: * Landing leg at the front * Foldable galvanized steel underrun guard for paver feeding * Enclosed single plastic mudguards * Front wall platform made of grating with step on drawbar and handholds on the front wall ----Chassis: Dkodpjx Ipbyjfx Apwjp * Chassis made of fine-grain steel ----Tipper body: * Steel 3-way tipper body with continuous asymmetrical aluminum side walls – without center stanchion – pendulum-mounted with manual central locking, left side foldable with side board spring lifter * Tailgate – made from HBW 400 steel – pendulum-mounted with automatic 2-claw lock * 5 mm steel floor made from HBW 450 steel ----Load securing: * 4 x 3 t lashing rings per side – recessed and foldable – integrated into the steel floor ----Roll tarp: * Roll tarp – agate grey, similar to RAL 7038 * Tarpaulin tensioning using ratchet tensioners on the sides and tensioning rubber at the front and rear ----Painting: * Chassis, underrun guard, and drawbar hot-dip galvanized * Axles, air tanks, landing leg, and flange towing eye painted in a shade of black * Side wall painting according to RAL color of choice (excluding special or metallic paints); color can be changed up to approx. 6 weeks before completion ----Info: * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale * Sample images (vehicle images may vary due to special equipment) ----Delivery time: * Vehicle available from week 42/2026

Stanje: novo, največja dovoljena obremenitev: 10.760 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic braking system (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic suspension with equalizer unit ----Drawbar / Flange towing eye: * Height-adjustable drawbar, adjustable by approx. 300 mm * Drawbar extension by 250 mm (up to 2,250 mm) * 40 mm flange towing eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General attachments: Dkjdpfx Aoxglibepwsp * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Low-bed loading area: * 50 mm softwood flooring * Pre-equipment for retrofitting container locks in front of the front wall * Bolted front wall made of smooth sheet metal * Foldable, trapezoidal-profiled steel side walls with drop-side spring assist * Sliding steel rear wall between the ramps (bracket for storage when not in use inside the front wall) * Bolted rear stanchions ----Load securing: * Perforated outer frame, bent at approx. 45°, with 2 t lashing capacity every 480 mm * Option to fit 3 t drop lashing rings every 600 mm * In each corner, front and rear: 1 x 6.3 t lashing ring * Various holes in the front and rear cross members for 1.2 t lashing options ----Ramps: * One-piece mechanical steel mesh ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, front wall, ramps, and rear wall * Drop-side color in RAL 9010 pure white * Painting of side walls in any RAL color available at extra cost ----Info: * Reinforced and certified body according to EN 12642 XL including load securing certificate * New vehicle with manufacturer’s warranty * Subject to prior sale and errors excepted ----Delivery time: * Available from approx. calendar week 30/2026

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 8.800 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brakes: * EBS brake system * Drum brakes * Emergency release device for spring-loaded cylinders Dkedpfxju I Iqls Apwjp ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange eye: * Drawbar with 40 mm screwed towing eye (height adjustable mm) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring ----General attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate; safety locking pins for various support heights * Closed steel sheet mudguards with splash protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with floor insert (installed horizontally), approx. 500 x 350 x 400 mm ----Superstructure: * Pivoting cable drum superstructure, clear width between drum arms 1,700 mm, with tension locks for securing the drum at the ends of the support arms, and central claw locking device securing the drum superstructure to the chassis * Motor-hydraulic drum drive with oil motor * Valves and movable, rubber-covered drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of stepwise offset centering cones made of polyamide ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Stanje: novo, največja dovoljena obremenitev: 18.900 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Lifting middle axle ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumpers * Mechanical rear drop-down supports ----Container / Low-bed Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length of 5,500 - 7,000 mm possible * Pneumatic 4-point container clamp locking as well as mechanically plug-in front stop angles in the guide tracks * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering of the skips, front 4 skip stops plug-in with pendulum stoppers Dkodpfx Aotplv Tepwjp ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning devices for positive and non-positive load securing of skips * 4 lashing rails in cloverleaf design (side) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Weld bead as anti-slip coating in the ramp incline running area * 1 pair of aluminum approach ramps (16 t/pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without initial registration with manufacturer warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3-in-1 = for roll-off containers, skip containers, and as a low-loader Dkodpfxol Thv Rs Apwjp ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm drawbar eye with height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no installation required on the truck side) ----General Attachments: * Toolbox made of powder-coated steel sheet, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box made of galvanized sheet metal for container nets, approx. 960 x 300 x 400/450 mm, right side * Plastic bumper buffer at rear * Mechanical drop-down supports at rear ----Load Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll containers * Steel floor with roller recesses in the bogie area * Possible to transport roll-off containers with a length of 5,500–7,000 mm * Pneumatic four-point clamp locking as well as mechanical locking angles at the front in the track, securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. volume of 10 m³ possible * Includes 8 removable tub stops for lateral centering of the tubs; front 4 stops plugged in with pivotable stop * Weld bead as anti-slip coating in the ramp area of the run-up incline ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements to securely fix the tubs * 4 lashing bars per side, cloverleaf design * 1 pair of 13.4 t UVV lashing rings at the front ----Ramps: * 1 pair of aluminium drive-on ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-wheeled and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight up to 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. calendar week 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 13.500 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA-Kombi 18.0: * 3 in 1 = for roll-off containers, skip containers, and as a low-loader Dsdpfel Thwcsx Apwekp ----Brakes: * TPMS (Tire Pressure Monitoring System) * EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders ----Axles: * 2 x 12 t Gigant axles ----Suspension: * Parabolic springs ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long * 40 mm towing eye and height adjustment device ----Electrical / Lighting: * LED tail lights * 15-pin power connector * TPMS, display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Tool box made of powder-coated sheet steel, right side * Side underrun protection * Plastic quarter mudguards with spray protection * Storage box for container nets, made of galvanized sheet, approx. 960 x 300 x 400 / 450 mm, right side * Plastic rear collision protection buffers * Mechanical drop-down supports at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, possible container length from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking as well as mechanically insertable stop angles at the front in the track, load securing certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ volume possible * Includes 8 removable skip stops for lateral centering of the skips, front 4 skip stops inserted with pendulum mount * Weld bead as anti-slip coating in the ramp area ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tension elements for positive and non-positive securing of the skips * 4 lashing bars each, cloverleaf design (side) * 1 pair of 13.4 t UVV lashing rings to the front ----Ramps: * 1 pair of aluminum access ramps (10.6 t/pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Information: * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Permissible gross weight of 20,000 kg technically possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 44 / 2026

Stanje: novo, največja dovoljena obremenitev: 8.850 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2024, * KA-TA-R 11.9 "Masterline" ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensating unit ----Drawbar / Flange Eye: * Approx. 300 mm height-adjustable drawbar with 40 mm flange eye ----General Fittings: * Jost mechanical landing gear at front * Rear: 2 mechanical, hot-dip galvanized drop-down support legs * Plastic toolbox approx. 750 x 350 x 300 mm, fitted on right side * Bolted underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS tire pressure monitoring system ----Tipping Platform: * Mesh hooks on the sides and rear in the central locking fixtures, plus 2 at the front wall * Steel pallet, 3-way tipping body (continuous sidewalls – without center stanchions – foldable with drop side spring assistance) * Rear stanchions bolted * Combination steel double rear doors, asymmetrically split, can be swung open and locked at 270°, not foldable – with additional pendulum frame for automatic tailgate opening during tipping operation; locking via galvanized swing bolt locking and central locking system * Deactivation function for automatic rear wall opening when tipping backwards with open door * 4 mm steel floor plate * Rear ramp carrier rail for drive-on ramps ----Load Securing: * 1 x 5 t lashing point in each corner * 4 x 3 t recessed lashing rings per side, fitted in the outer frame ----Ramps: * 1 pair of aluminum drive-on ramps approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for vehicles on rubber tires & tracks * Lockable storage compartment for ramps under the loading platform, integrated into the chassis ----Paint Finish: * Drawbar, front wall, tipping platform, rear stanchions, underrun protection, and mechanical support legs hot-dip galvanized * Sidewalls and tailgate painted RAL 9010 pure white * Sidewall painting in any RAL color available at extra charge * Axles, springs, flange eye, air tank, and landing gear painted in a black tone ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer’s warranty * Errors and prior sale excepted Dkjdsl Thyxopfx Apwjp ----Delivery Time: * Immediately available ex-works Egestorf on A7

Stanje: novo, največja dovoljena obremenitev: 30.740 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift/lowering system and RtR valve * Smard board for load weight determination * Warning sign packages front & rear * Reflective contour marking tapes on sides and rear * Rotating beacon (removable) at rear * LED lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design, right-hand side * Closed single plastic mudguards at front * Straight rear steel splash guards, each with spray suppression * Side underrun protection * Turntable platform front extension by 520 mm with 45° corners and 3 flush storage compartments with lids, lockable * Chassis made of high-strength fine-grained steel * Decking above turntable platform: 50 mm softwood, in low-bed platform: 60 mm softwood * Outer planks of access ramps: hardwood * Each side features 4 stake pockets (stakes not included), with simultaneous 2 t lashing points * Lashing package includes: 2 lashing rings 6.4 t, front left and right on main frame of turntable platform * On sides, front & rear, 2 pairs of 13.4 t lashing rings on outer frame; sides each with 4 pairs of 10 t lashing rings, pivoting & lowerable * Loadable in all directions, recessed in the outer frame * 2 pairs of 6.4 t lashing rings on the excavator stick rest area * 8 pairs of galvanized folding outriggers for 3 m overall width (not in the rear slope) * Extension planks stored left side in a stowage compartment * Excavator stick rest above rear axle to rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports, rear * Hydraulic folding ramps with hydraulic tip section approx. 4,650 x 720 mm including lateral hydraulic ramp shift & load holding valve * Load area over turntable: approx. 2,990 x 2,520 mm * Rear load area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm drive-on slope) Dkedpsl Tphrefx Apwop * Flow divider installed * Chassis, turntable, ramps, outrigger arms, and mechanical rear supports hot-dip galvanized * Axles, drawbar, air reservoir, and turntable painted in a black tone * Tires: 235/75 R 17.5 * New vehicle, not previously registered, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2-in-1: Suitable for swap containers (Abrollbehälter) and as low-loader trailer ----Braking System: * EBS electronic braking system * Emergency release facility for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10-ton axles ----Suspension: * Air suspension with lift and lower system and RTR valve ----Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * Tire pressure monitoring system, display option in truck via EBS signal (no truck-side installation required) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Tool box, powder-coated steel, approx. 1,000 x 300 x 600 mm * Storage box for container net, galvanized sheet metal, 960 x 300 x 450/400 mm * Reflective contour tape on sides and rear * Side underrun protection * Plastic quarter mudguards with splash guards * Rear plastic buffer bumper * Foldable 'A' sign at the rear ----Loading Platform: * Main frame with raised outer frame to guide swap containers * Steel sheet floor with recesses for rollers in the bogie area * Container length possible from 5,500 to 7,000 mm * Pneumatic 4-point clamping lock and mechanical plug-in stops in the running channel at the front, securing certificate according to DIN 30722-1 * Weld bead as anti-slip covering in the inclined running area * Mechanical drop-down supports at the rear ----Load Securing: * 1 pair 10 t UVV lashing rings at the front wall carrier * 3 pairs 10 t UVV lashing rings on each side of the outer frame * Each side with 4 x 2 t cloverleaf lashing eyes * 4 x 8 t recessed lashing brackets in the outer frame ----Ramps: * 1 pair aluminum loading ramps (10.6 t/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from rear) ----Paintwork: * Chassis, bogie, locking elements, rear drop-supports hot-dip galvanized * Drawbar, axles, and air tanks painted in a black shade ----Additional Info: * New vehicle, no initial registration, full manufacturer warranty * Subject to errors and prior sale Dkodpfx Apsl Tq Nmewsp * Sample images ----Delivery Time: * Available approx. from KW 43 / 2026

Stanje: novo, največja dovoljena obremenitev: 17.650 kg, skupna masa: 24.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 9.230 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic brake system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11-tonne Gigant axles ----Suspension: * 17.5" air suspension with lift and lowering device ----Drawbar: * 1,800 mm long drawbar with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck display via EBS signal (no truck-side installation required) * 15-pin power connector * 2 additional LED reversing spotlights (switched via reverse gear) * LED lighting ----General fittings: * Aluminium air tank * Stainless steel toolbox on the side, approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix outer frame bent at 45°, hole pattern for lashing equipment, lashing force per lashing point 2,000 kg at a spacing of 480 mm * Installation of 3,000 kg drop lashing brackets at approx. 600 mm spacing possible – each side is equipped with 12 pcs. 3,000 kg lashing brackets included in delivery * Each side has 5 pockets for 100 x 50 mm stake posts in the outer frame – stakes not included in delivery * 30 mm phenolic resin-coated plywood floor ----Drum supports: * 3 pcs. galvanised drum supports secured by container locks with side forklift pockets center/center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-bracing * Permissible drum weight per cable support 6,000 kg * Without drive and drum brake * Support arm with clamping lock for securing drum shaft * Steel drum shaft 76 mm diameter, with centring and rotating ends Dsdpox Nli Nefx Apwekp * 2 locating rings * 2 centring cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for securing the drum against rotation and uncoiling by the customer ----Loading height: * Approx. 1,040 mm loaded ----Paintwork: * Chassis, turntable, drawbar, outer frame, underrun protection hot-dip galvanised * Axles painted in a shade of black ----Information: * Technical upgrade to 30 tonnes GVW possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from week 51/2026

Stanje: novo, največja dovoljena obremenitev: 37.560 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW axles * Start assist for shunting purposes on the first axle, activated via EBS (without truck-side installation) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes from the driver’s cab via EBS (without truck-side installation) Dedpoykx Nkjfx Apwekp ----Suspension: * Air suspension with lift and lowering function as well as RtR valve ----Electrics / Lighting: * Smart-Board infotool mounted on trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 7-pin socket at rear for overlength lighting * Side marker lamps with indicator function * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) ----General Attachments: * Side underrun protection * Support legs at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swing arm as a carrier for connecting lines from truck to semi-trailer ----Low Loader Platform: * 2nd king pin position * Gooseneck platform with 45° chamfered front corners and front-mounted toolbox made of galvanized, powder-coated sheet steel B = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (in desired RAL color) foldable and removable along the gooseneck platform * Rear wall, insertable, height 150 mm * Rear incline on the gooseneck platform to the low-bed approx. 700 mm long with checker plate covering and at the end a perforated strip for attaching aluminum approach ramps * Gooseneck platform with 50 mm clamped wooden planks, low-bed platform with 60 mm clamped wooden planks * Tread plate over axles * 9 mechanical extension panels to a total width of 3 m, not included in the rear incline (extension planks available with closed transverse stowage compartment under load floor) * Preparation for 3 storage recesses under the gooseneck platform for optional storage of aluminum approach ramps or planks for covering wheel recesses * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Gooseneck platform: * Perforated outer frame, 45° angled, with hole pattern for lashing devices (2 t lashing capacity per point with a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor per side (1 x on gooseneck platform, 1 x on longitudinal frame after the cranking, 1 x above middle axle next to longitudinal frame) Low-bed platform: * 3 x 13.4 t lashing rings per side at the outer frame (1 x start of gooseneck cranking, 1 x start of approach ramp, 1 x end of approach ramp) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side screwed to outer frames of the wheel recesses (2 at front wheel recess, 1 at rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last rigid axle over the steering axle to the end cross member, continuous with internal reinforcing profile approx. W = 770 mm x T rear

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Braking system: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lowering system, including RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED beacon, rear left ----General Attachments: * Side underrun protection * Support legs at the front and mechanical swivel supports at the rear of the chassis * Straight pressed steel fenders * Spare wheel holder under the chassis, right side Dsdpfoy Ngzyox Apwokp ----Low Loader Deck: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm aluminium side boards (RAL 9010 pure white) on the fifth wheel platform, foldable and removable * Rear board plug-in, 150 mm high * Rear slope on fifth wheel platform to low-bed approx. 700 mm long * Fifth wheel platform with 50 mm timber planks, low-bed deck with 60 mm timber planks * Tread plate above the axles ----Widenings: * 8 x mechanical folding extensions to a total width of 3 meters (not on rear slope; extension planks available with storage on the platform) * Mechanically adjustable warning panel sets front and rear ----Load Securing (Lashing Package): * On the fifth wheel platform: 2 x 6.3 t lashing rings on each side, plus 3 x 5 t lashing bars per side in the outer frame * On the low-bed platform: 2 x 13.4 t lashing rings per side, plus 4 x 10 t lashing rings, pivotable and lowerable, recessed in the outer frame * 2 x 6.4 t lashing eyes per side, plus 1 lashing ring at the excavator arm rest * 2 x container locks directly after the neck in the low-bed platform ----Excavator Arm Rest: * Continuous excavator arm rest from end of last fixed axle over steering axle to end crossbeam, with internal reinforcements, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanical one-piece hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * Outer board on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope * Rubber matting on ramp and approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump performance in the truck between 40 l/min and 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Fifth Wheel Height: * approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Coating: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, support legs, air tanks painted in a black shade * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Sample images may show equipment not included with the offered vehicle ----Delivery time: * available from c

Stanje: novo, največja dovoljena obremenitev: 30.440 kg, skupna masa: 40.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, Oprema: ABS, T 4 Profi 40,0 ----Zavore: * Wabco EBS-E (električni zavorni sistem) * Naprava za izredno sprostitev zavor za cilindere vzmetne akumulacije * Bobnaste zavore ----Osi: * 4 x 11 t Gigant osi ----Vzmetenje: * Zračno vzmetenje s sistemom za dvig in spuščanje ter ventilom RtR ----Povezava vlečne glave: * Naravna povezava vlečne glave s 50 mm vtičnico in brezstopenjsko nastavljivo višino ----Elektrika / Osvetlitev: * Sistem za nadzor tlaka v pnevmatikah z možnostjo prikazovanja na zaslonu tovornjaka preko signala EBS - brez namestitve na tovornjaku * SmartBoard kot informacijsko orodje z senzorji tlaka za prikaz obremenitve osi na posamezni skupini osi * 15-polni električni vtič * LED zadnje luči Dodjylfvmepfx Apwjkp * LED obodna svetila (odstranljiva) zadaj ----Splošni dodatni deli: * Paketi opozorilnih tablic spredaj in zadaj * 2 x orodne omare iz pocinkane in prašno lakirane jeklene pločevine, cca 650 x 300 x 600 mm, na desni strani * Spredaj zaprt plastični blažilnik * Zadaj ravne jeklene zaščitne plošče s ščitnikom proti brizganju (zmanjšanje pršenja) * Stranski zaščitni element ----Površina nizkega nakladalnika: * Podaljšana platforma z vrtljivim podvozkjem za 520 mm, z 45° koti in 3 vgrajenimi predali z pokrovi in ključavnico * Talna obloga nad platformo z vrtljivim podvozkjem iz 50 mm iglasta lesa, v platformi nizkega nakladalnika pa iz 60 mm iglasta lesa * Gumijasta obloga 20 mm namesto lesene talne obloge v območju poti, s skupno dolžino nizke platforme 6.780 mm, vključno z rampo za vožnjo * Gumijasta obloga na rampi za vožnjo na levi in desni strani, dolžina cca 860 mm * Na vsaki strani 4 žepi za opornike (oporniki niso vključeni), skupaj z možnostjo pritrjevanja dveh ton * Okvir, izdelan iz visoko trpežnega finozrnatega jekla ----Šasi: * Šasi iz visoko trpežnega finozrnatega jekla ----Zavarovanje tovora (paket Lasi): Platforma z vrtljivim podvozkjem: * 2 para 13,4 t pritrdilnih točk v zunanjem okvirju platforme z vrtljivim podvozkjem Nizka platforma: * Na vsaki strani 4 pari 10 t pritrdilnih točk na zunanjem okvirju, z možnostjo spuščanja in obremenitve v vse smeri * Na vsaki strani zadaj 2 para 13,4 t pritrdilnih točk, ki se lahko vrtijo ----Rampe: * Gumijasta obloga na zložljivih rampah za vožnjo * Hidravlične zložljive rampe z hidravlično nastavljivim končnim delom, cca 4.650 x 720 mm * Hidravlično stransko premikanje ramp in varnostni ventili za obremenitev ----Zadnja opora: * Hidravlična zadnja opora ----Širitev: * 8 parov pocinkanih zložljivih podaljškov za 3 m skupne širine (vendar ne na zadnji rampi) * Plošče za razširitev, nameščene na levi strani v predelu za shranjevanje ----Nosilec za bager: * Nosilec za bager nad zadnjo osjo do konca rampe za vožnjo, cca D=2.100 mm x Š=740 x V=190 mm * 2 para 13,4 t pritrdilnih točk na nosilcu za bager ----Hidravlika: * Hidravlični razdelilnik pretoka na prikolici (pri hidravlični moči črpalke na tovornjaku, ki je večja od 40 - maks. 120 l/min) ----Dimenzije nakladalnega prostora: * zadnja nakladalna površina: cca 6.780 x 2.520 mm (vključno z 860 mm rampo za vožnjo) * nakladalna površina nad vrtljivim podvozkjem: cca 2.990 x 2.520 mm ----Višina nakladanja: * pribl. 890 mm, +/- 20 mm ----Barvanje: * Stranska in zadnja odsevna pasova * Šasi, vrtljivi podvozek, rampe za vožnjo in zložljivi podaljški, vroče pocinkani * Osi, povezava vlečne glave, zračni rezervoar in vrtljivi podvozek, pobarvani v črno barvo ----Informacije: * Novo vozilo z garancijo proizvajalca * Napake

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle is self-steering (lockable from the cab for maneuvering purposes without any installation on the truck side, and additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering (truck-side installation required), with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm draw eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an info tool with pressure sensors for axle load indication per axle group * Tire pressure monitoring with display in the truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * LED rotating beacon (removable), rear ----General Fittings: * Mechanical warning sign set for 3 m total width * Toolbox made of galvanized steel plate approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 stowage compartments with lockable folding lids (folding towards the rear) * Shortening of the low-bed platform by 500 mm to 6,280 mm including extended recess by 500 mm at the front * Rubber covering on the folding frame, approach ramp, and running surface of the low-loader platform * Bamboo wood between the longitudinal beams, in front of the excavator stick rest area ----Load Securing (LaSi Package): * 2 x 6.4 t lashing eyes in the front corners * 2 x 13.4 t UVV lashing points on each side in the front and rear corners * 5 x 10 t UVV lashing rings on each side (swivelable and lowerable, loadable in all directions) * 4 stake pockets per side with simultaneous 2 t lashing option * 1 x 16 t UVV lashing ring on the rear crossmember ----Width Extension: * Extendable and foldable width supports for 3 m total width (plank holder under the chassis, right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to end beam approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-circuit hydraulics and folding tip approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs on the truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm adjustable via air suspension ----Loading Area Dimensions: * Platform above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading platform: 6,280 + 500 x 2,520 mm, incl. 860 mm approach ramp ----Paintwork: * Chassis, turntable, drawbar, width extension consoles, ramps hot-dip galvanized * Drawbar yoke, axles, hydraulic axle supports and air tanks painted in black ----Information: Dodpfx Asxptn Dspwskp * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery Time: Available immediately*

Stanje: novo, največja dovoljena obremenitev: 8.600 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2025, * KA-TA-R 11.9 Masterline: ----Braking system: * Wabco EBS * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Towing Eye: * Height-adjustable hot-dip galvanized drawbar, adjustable by 300 mm, with 40 mm flange towing eye ----Electrical / Lighting: * RDÜ tire pressure monitoring system * LED lighting * 15-pin power connector ----General Attachments: * Toolbox made of galvanized sheet steel on the right side * Bolted underrun protection * Plastic quarter mudguards * Jost mechanical landing gear at the front * Two mechanical hot-dip galvanized folding supports at the rear ----Tipper body: Dedpfx Aov Dz N Aspwokp * Mesh hooks on the sides and rear in the central locking mounts plus 3 pieces on the outside of the front panel * Hot-dip galvanized chassis * Steel pallet 3-way tipper body * Continuous, drop-down side walls without center stanchion, with drop-side spring lift assist * Rear drop gate can be swung down or used as a pendulum via manual central locking * Hot-dip galvanized, bolted rear stanchion * 4 mm steel floor plate * Rear mounting rail for loading ramps ----Load securing: * One flush-mounted, foldable 5 t lashing ring in each corner * Four flush-mounted, foldable 3 t lashing rings in the outer frame on each side ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles * Lockable rear storage compartment underneath the loading area, integrated into the chassis ----Tires: * Tires 235/75 R 17.5 ----Paintwork: * Axles, springs, air tanks, drawbar, and landing gear painted black * Drop side painted RAL 9010 pure white * Painting of the side walls in any RAL color possible for an extra charge * Floor and front wall hot-dip galvanized ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Stanje: novo, največja dovoljena obremenitev: 10.900 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2026, * KA-TA-R 14.4 ----Braking system: * Wabco EBS * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Towing Eye: * Height-adjustable (approx. 300 mm), hot-dip galvanized drawbar with 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding supports at the rear * Hot-dip galvanized bolted underrun protection * Toolbox made of galvanized steel sheet, mounted on the right side * Plastic quarter mudguards * Two-step entry on the left side as access aid ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin electrical connector * LED tail lights ----Tipper Platform: * Steel pallet three-way tipping body * Continuous side walls at the top with internal tube reinforcement (without central stanchions), foldable using drop side spring lifters * Rear wall foldable and pendulum-mounted, with manual central locking * Hot-dip galvanized, bolted rear stanchions * 4 mm fine-grain steel floor plate * Mesh hooks, rear mounting rail for drive-on ramps * Prepared for later retrofitting with side wall extensions Dedpfxsl Th A Ej Apwjkp ----Chassis: * Hot-dip galvanized chassis ----Load Securing: * Each corner with 1 x 5 t lashing ring and each side with 4 x 3 t lashing rings embedded in the outer frame ----Aluminum Drive-on Ramps: * 1 pair of aluminum drive-on ramps approx. 3,570 x 400 mm (load capacity 8 t/pair) suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading platform integrated in the chassis, accessible from the rear ----Tires: * 385/55 R 22.5 tires ----Painting / Coating: * Axles, springs, air tanks, and landing gear painted in black * Chassis, drawbar, floor, front wall, and folding supports hot-dip galvanized * Sidewall finish in RAL 9010 pure white * Side wall painting in other RAL colors available at extra cost ----Info: * Reinforced superstructure with load securing certificate according to EN 12642 XL * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 29/2026

Stanje: novo, največja dovoljena obremenitev: 38.620 kg, skupna masa: 50.000 kg, konfiguracija osi: 3 osi, Leto izdelave: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle self-steering (lockable from the driver's cab for maneuvering purposes without the need for truck-side installation; additionally lockable via switch on trailer). Deactivate the lock before driving on public roads. * Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required), with speed-dependent control via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Dsdpfx Ael Tihujpwekp * Drawbar, 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with indication in the truck via EBS signal (no truck-side installation necessary) * LED lighting system 12/24 V * Removable rear LED beacon ----General Accessories: * Mechanical warning plate kit for 3 m total width * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, mounted side left * Front axle with plastic mudguards, rear with galvanized steel mudguard skirts ----Low Loader Platform: * Front section of turntable platform with 45° angles and 3 storage compartments with lockable, rear-hinged covers * Shortening of the lowbed platform by 500 mm to 6,280 mm including extended step by 500 mm to the front * Rubber covering on folding frame, drive-on ramp and running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator arm rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at front corners * 2 x 13.4 t UVV lashing points each at side front and rear corners * 5 x 10 t UVV lashing rings per side (pivoting and lowerable, loadable in all directions) * 4 stake pockets per side with additional 2 t lashing capability each * 1 x 16 t UVV lashing ring on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m total width (beam holders under chassis, right side) ----Excavator Arm Rest: * Continuous excavator arm rest with reinforcement profile from last axle to tow bar approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on sides of arm rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and extendable tip piece approx. 4,650 x 720 mm including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (required in case of hydraulic pump output on truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Lowbed platform: 6,280 + 500 x 2,520 mm incl. 860 mm inclines ----Paintwork: * Chassis, turntable, drawbar, widening consoles, and ramps hot-dip galvanized * Tow bar, axles, hydraulic axle supports, and air tanks painted in black ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately*

Stanje: novo, največja dovoljena obremenitev: 38.290 kg, skupna masa: 48.000 kg, konfiguracija osi: 3 osi, dolžina tovornega prostora: 8.500 mm, širina tovornega prostora: 2.520 mm, Leto izdelave: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: Dsdpfxol Tnvgs Apwjkp * 3 x 11 t BPW Eco Plus axles * Last axle hydraulically steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lower function as well as RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on trailer as info tool with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * Removable LED flashing beacon, rear left ----General attachments: * Side underrun protection * Landing gears in the front and mechanical swing supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder mounted on the chassis, right-hand side ----Low-loader platform: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel, width = 2,480 mm x height = 500 mm x length = 665 mm, with folding lid * 400 mm high aluminum sideboards (RAL 9010 pure white) on both sides of the fifth wheel platform, foldable and removable * Rear wall – 150 mm high, slotted in * Rear slope on the fifth wheel platform down to the low-bed area, approx. 700 mm long * Fifth wheel platform fitted with 50 mm wooden planks, low-bed area with 60 mm wooden planks * Tread plate above the axles ----Width extensions: * 8 x mechanical folding width extensions to a total width of 3 m, except in the rear slope area (extension planks available with storage on the fifth wheel platform) * Mechanically adjustable warning sign packages front and rear ----Load securing (lashing package): * On the fifth wheel platform, 2 x 6.3 t lashing eyes each as well as 3 x 5 t lashing bars on each side in the outer frame * In the low-bed area, 2 x 13.4 t lashing rings on each side as well as 4 x 10 t lashing rings, swiveling and retractable, integrated into the outer frame * 2 x 6.4 t lashing eyes on each side and 1 lashing eye at the rear in the excavator trough * 2 x container locks directly after the kick-up section in the low-bed platform ----Excavator trough: * Excavator trough from end of last rigid axle over steering axle up to the end brace, continuous, with internal reinforcement profile, approx. L = 2,450 mm x W = 770 mm x D = 270 mm ----Ramps: * Mechanically single-piece, hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * The outer board of the ramp is made from 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacities in the truck from over 40 l to 120 l/min) ----Loading dimensions: * Loading area of fifth wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach slope) ----Coupling height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, ramps, rear swing supports, extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in black tone * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may contain equipment not included with the offered v

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9,9 ML: ----Zavora: * EBS-zavorni sistem * Bobnasta zavora * Naprava za nujno sprostitev za vzmetno shranjevalni valj ----Os: * BPW os ----Vzmetenje: * Parabolične vzmeti ----Vlečna cev / prirobnica vlečne zanke: * Vlečna cev s 40 mm vijačno vlečno zanko (nastavljiva po višini mm) ----Elektrika / Razsvetljava: * 15-polni električni priključek * LED razsvetljava * utripajoče LED stranske označevalne luči * RDÜ nadzor tlaka v pnevmatikah ----Splošni priključni deli: * Podporna vitla spredaj * Vzmetno podprte kvadratne podpore zadaj z osnovno ploščo; varnostni zaporni zatiči za različne višine podpore * Zaprta blatnika iz jeklene pločevine z zaščito pred pršenjem * Zaprta stranska zaščita z možnostjo uporabe kot oglasna površina * Plastična orodjarna z dnom (v ležeči vgradnji) pribl. 500 x 350 x 400 mm ----Nadgradnja: * Zasučna kabelska vitelna nadgradnja, svetla širina med ročicami vitla 1.700 mm, z zapiralom za pritrditev vitla na koncih nosilne roke ter z aretacijo kabelske vitelne nadgradnje in podvozja z osrednjo kremensko zaporo * Motoriziran hidravlični pogon vitla z oljnim motorjem * Ventili in premični pogonski valji z gumijasto prevleko * Hidravlični regulator hitrosti in zavora za pogon vitla * Jeklena vitelna os premera 76 mm z centriranjem in vrtljivimi konci * 1 par centrirnih stožcev iz poliamida, stopničasto oblikovanih ----Podvozje: * Podvozje iz torzijsko odpornih kvadratnih cevi in prečk ----Črpalna enota: * Hidravlična črpalna enota z bencinskim motorjem Loncin, vključno z ročnim in električnim zaganjalnikom * Rezervoar za gorivo in ročni zaganjalnik Dksdsu I Iqfspfx Apwop * 13 KM z zobniško črpalko (150 bar) ----Pnevmatike: * 315/80 R 22,5 ----Lastna masa: * 2.690 kg lastne mase ----Barva: * Vozilo je vroče pocinkano ----Informacije: * Novo vozilo s polno proizvajalčevo garancijo * Napake in vmesna prodaja pridržane ----Dobavni rok: * dobavljivo približno od 41. tedna/2026 dalje

Stanje: novo, največja dovoljena obremenitev: 6.870 kg, skupna masa: 9.900 kg, konfiguracija osi: 1 os, Leto izdelave: 2026, * KWH 9.9 ML: ----Brake System: * EBS braking system * Drum brakes * Emergency release device for spring brake cylinders ----Axle: Dsdpeu I Iq Esfx Apwokp * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange Eye: * Drawbar with 40 mm bolted towing eye (height-adjustable mm) ----Electrics / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * RDÜ tire pressure monitoring system ----General Attachments: * Support winch at the front * Spring-assisted square tube supports at the rear with base plate. Safety locking pins for various support heights * Closed steel mudguards with spray protection * Closed side underrun protection, can be used as advertising space * Plastic toolbox with floor inlay (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, clear width between drum arms 1,700 mm, with tension lock on the drum arm ends, plus central claw lock securing the cable drum superstructure to the chassis * Motor-driven hydraulic cable drum drive with oil motor * Valves and movable, rubber-coated drive rollers * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of polyamide centering cones, stepped ----Chassis: * Chassis made from torsion-resistant square tubing and cross beams ----Pump Unit: * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) ----Tyres: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized ----Notes: * New vehicle with full manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately from Egestorf

Stanje: novo, največja dovoljena obremenitev: 8.670 kg, skupna masa: 11.900 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 5.000 mm, širina tovornega prostora: 2.420 mm, višina nakladalnega prostora: 500 mm, Leto izdelave: 2025, * KA-TA-R 11.9 Masterline: ----Braking system: * Wabco EBS * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensation unit Dsdpfx Apsq Hg Dxjwokp ----Drawbar / Flange Towing Eye: * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flange towing eye ----Electrics / Lighting: * RDÜ tire pressure monitoring system * LED lighting * 15-pin power connector ----General attachments: * Tool box made of galvanized sheet steel, mounted on the right side * Bolted underrun guard * Plastic quarter mudguards * Jost mechanical landing gear at the front * Two rear mechanical hot-dip galvanized folding supports ----Tipper body: * Net hooks on the sides and rear integrated into the central locking brackets as well as 3 pieces mounted externally on the front wall * Hot-dip galvanized chassis * Steel 3-way tipping body * Full-length drop sides without center post, folding down with drop side spring assist * Rear flap drop-down and swinging, lockable via manual central locking * Hot-dip galvanized bolted rear stanchion * 4 mm steel floor plate * Rear mounting rail for loading ramps ----Load securing: * 1 x 5 t recessed and foldable lashing ring in each corner * Additionally, 4 x 3 t recessed and foldable lashing rings in each side frame ----Ramps: * 1 pair of aluminium loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable storage compartment integrated under the loading area at the rear of the chassis ----Tyres: * Tyres 235/75 R 17.5 ----Painting: * Axles, springs, air tanks, drawbar, and landing gear painted in a shade of black * Sideboard painted RAL 9010 pure white * Painting of side walls in any RAL color available at extra cost * Floor and front wall hot-dip galvanized ----Information: * Reinforced body with EN 12642 XL load securing certificate * New vehicle with manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Available immediately ex works Egestorf

Stanje: novo, največja dovoljena obremenitev: 13.700 kg, skupna masa: 18.000 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 7.000 mm, širina tovornega prostora: 2.480 mm, Leto izdelave: 2026, * TRA 18.0: * 2 in 1 = for roll-off containers and as low-bed trailer ----Braking system: * EBS electronic braking system * Emergency release for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 ton axles ----Suspension: * Air suspension with lift and lowering system, including RTR valve ----Drawbar: * Drawbar, 2,000 mm long with 40 mm towing eye and height adjustment ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: * Tool box made from powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Storage box for container net made from galvanized sheet, 960 x 300 x 450/400 mm * Reflective contour marking tape on sides and rear * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumper buffers * Foldable rear A-board ----Loading area: * Main frame with raised outer rails to guide the roll-off containers * Steel floor plate with roller recesses in the bogie area * Container length of 5,500 - 7,000 mm possible * Pneumatic 4-way clamp lock, as well as mechanical plug-in stop angles at the front of the guide track, load securing certificate according to DIN 30722-1 * Weld bead as anti-slip coating in the ramp area * Mechanical drop-down supports at the rear ----Load securing: * 1 pair of 10 ton UVV lashing rings at the front on the bulkhead carrier * 3 pairs of 10 ton UVV lashing rings on the outer frame (side) * 4 pairs of 2 ton side lashing eyes with cloverleaf design on each side * 4 x 8 ton recessed lashing brackets in the outer frame ----Ramps: * 1 pair of aluminum access ramps (10.6 tons/pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paintwork: * Chassis, bogie, locking parts, rear drop-down supports hot-dip galvanized * Drawbar, axles, air tanks painted in black Dkedpel Tpc Asfx Apwep ----Information: * New vehicle without first registration, with full manufacturer's warranty * Subject to errors and prior sale * Sample images ----Delivery time: * Available from approx. week 43 / 2026

Stanje: novo, največja dovoljena obremenitev: 10.360 kg, skupna masa: 14.400 kg, konfiguracija osi: 2 osi, dolžina tovornega prostora: 6.270 mm, širina tovornega prostora: 2.470 mm, višina nakladalnega prostora: 400 mm, Leto izdelave: 2025, * ETÜ-TA-ER 14.4: ----Braking System: * Electronic Braking System (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Towing Eye: * Drawbar height-adjustable by 300 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS (tire pressure monitoring system with indicator function in the truck via EBS signal—no installation required on the truck side) * LED lighting system * 15-pin electrical connector ----General Accessories: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox mounted front right on the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floorboards * Preparation for subsequent installation of 20" container locks at front and rear * Bolted, smooth sheet metal front wall * Side walls made of trapezoidal-profiled steel, foldable with drop-side spring assist * Hot-dip galvanized bolt-on rear stanchions ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing points every 480 mm * Option for 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in front and end crossmembers for 1.2 t securing points ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles, stored in a compartment underneath the loading area in the chassis, accessible from the rear ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, front wall, and rear wall Djdpendpn Ssfx Apwekp * Entire vehicle hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex works Egestorf