Tehnologija gnojevke

Briri APTW 15

APTW 15
0010 RI Single-Axle Special Slurry Spreader Tanker
0020 APTW 15
0030 Approx. 15,500 ltr. capacity, galvanized
0040 Tank recesses for wheels
0050 Cylinder approx. 2000 mm diameter
0060 Length approx. 5200 mm
0090 Large multi-chamber lights, bottom and top
0100 Mounted on the linkage
0110 Hydraulic support leg
0120 Continuous, reinforced galvanized frame rails
0130 With rear towing eye
0140 Baffle plates according to regulations
0150 Hydraulic 6" three-way valve at the rear
0160 Filling level indicator with float and visible arrow at the front
0170 Manually operated domed lid at the top
0180 Two-line air brake system with ALB regulator via
0190 Float indicator at the front of the tank
0200 Heavy-duty axle, 10-bolt, brake 520 x 180
0210 At 40 km/h approx. 30 t
0220 Underslung hitch type "Profi" with ball head
0230 and 4 t support load
0240 Hydraulically suspended drawbar with oil reservoir
0250 With pressure gauge and shut-off ball valve, also for
0260 Front vehicle leveling
0270 Four-point linkage Cat. III, reinforced rear version
Fsdpfx Aleyxh Ndj Hsgb
0280 Lifting capacity approx. 4 t, incl. hydraulic connections & 12 V
0290 Lighting socket
0300 Vogelsang VX 186-260 Q rotary lobe pump up to
ltr./min. with attached hydraulic motor and on-board hydraulics
0320 For pump drive only
0330 Hydro-chopper M 10000 with manual reversing valve and
0340 Automatic-hydraulic knife pre-tensioning
0350 Inlet port front left 200 mm with quick coupler
0360 Pump intake with 8" gate valve
0370 Wide-angle PTO shaft
0380 Automatic-hydraulic filling stop via
0390 Float indicator for any filling quantity
0400 40 km/h TÜV report with mudguards
0410 Tyres: 900/60 R 42/186D BKT,
0420 Approx. 2147 x approx. 900, 2 units with warning plates
0430 Electro-hydraulic control with operating terminal per
0440 BUS system with display, membrane keyboard, function indicator
0450 With switching functions for:
0460 EW drawbar
0470 DW pump intake
0480 DW three-way valve
0490 DW four-point linkage
0500 DW folding/unfolding
0510 Drip-stop for e.g. slot applicator
0520 Section control left
0530 Section control right
0540 DW distributor with hole discs
0550 EW with return – chopper and filler in suction arm
0560 Hydraulic lifting of suction arm
0570 Swinging suction arm right / left
0580 Bending suction arm cylinder 1
0590 Bending suction arm cylinder 2
0600 DW slide valve suction arm
0610 Special vehicle width to approx. 3300
0620 mm (axle track approx. 2200 mm) by
0630 offset rims included
0640 Mudguard extensions (from
0650 external width 3000 mm, a
0660 special permit must be applied for)
0670 Support load enhancement by two-chamber tank
0680 Suction arm 200 mm diameter, mounted on top of tank
0690 Swivels right and left
0700 Incl. docking ball 200 mm
0710 Super turbo filler 200 mm diameter
0720 Mounted on top in suction arm

Oglas je bil avtomatsko preveden. Možne so napake pri prevodu.